Bloomfield 1090 User Manual

Technical Data

Wall Bracket

Stile

Headrail

(cross section)

Hex Nut

Flat Washer

Lock Washer

Hex Nuts

Flat Shoe Retainer

Wedge Anchor

Flat Washer

Leveling Bar

Slide
Latch

Keeper

Bracket

Panel

Screw

Bracket

Coat
Hook

Hinge

Hinge

Bracket

Threaded

Inserts

Stile

Door

Threaded

Inserts

Stile

Threaded

Inserts

Door

Screw

Through Bolts

Door
Stop

Screw

Angle

Bracket

Continuous

Hinge

Slide

Latch

Keeper

Door
Stop

Angle

Bracket

Threaded

Inserts

Stile

Door

Threaded

Inserts

Stile

Threaded

Inserts

Door

U-channel

Continuous Hinge

Panel

Screw

Through Bolts

Coat

Hook

Threaded

Rod

Lock Washer

Flat Washer

Hex Nut

Stile

Leveling Bar

Shoe Retainer

I-Beam

(not furnished)

Finished

Ceiling

Bevel Washer

Spacer

Specify Product Application:

 Toilet Partitions
 Dressing Compartments
 Shower Dividers
 Urinal Screens
 With Outswing Door
 With Institutional Hardware (.67)

SierraSeries

®

WATER- AND FIRE-RESISTANT

SOLID COLOR REINFORCED

COMPOSITE TOILET PARTITIONS

AND URINAL SCREENS

Specify Series Required:

 1091 Series Floor-Anchored (Screens only)
 1092 Series Overhead-Braced
 1093 Series Post-to-Ceiling (Screens only)
 1095 Series Wall-Hung (Screens only)
 1096 Series Floor-to-Ceiling Anchored
 1098 Series Ceiling-Hung 8' 0" (244cm) Ceiling Maximum

GraffitiOff™

Surface

1090

SERIES

Solid Color
Reinforced
Composite

Material

STANDARD-SIZE COMPONENTS:
Stiles: For compartments — 3", 4'', 5'', 6'', 8'', 10'', 12'', 16'', 20'', or 24'' (8, 10,

13, 15, 20, 25, 30, 41, 51, or 61cm) wide; overhead-braced — 83'' (211cm) high;
floor- to-ceiling anchored — height as required; ceiling-hung — 83'' (211cm) high

for 8' 0'' (244cm) ceilings or as required up to 10' 0'' (305cm) ceilings.

Doors: 58'' (147cm) high. Inswing doors are standard for 22'' to 37'' (56–94cm)
widths in whole-inch increments. Outswing

b

doors are standard for 25'' to 37''

(64–94cm) widths in whole-inch increments.

Wall Posts: — 1-1/2'' wide x 58'' high (4 x 147cm).

COMPARTMENT AND SCREEN ELEVATIONS

18 - 60''

46 - 152cm

21''

53cm

25''

64cm

18''

46cm

1091 Series

Floor-Anchored Screen

58''

147cm

12''

30cm

Post

21''

53cm

25''

64cm

18''

46cm

Headrail

1092 Series

Overhead-Braced

58''

147cm

85''

216cm

12''

30cm

Wall Hung
Urinal Screen Bracket

Panels: For compartments — Up to 84'' (213cm) wide; 58'' (147cm) high. For
wall-hung screens — 18'' or 24'' (46 or 61cm) wide; 42'' or 48" (107 or 122cm)

high. For ceiling-hung and post-to-ceiling screens — 24'', 36'', 48'', or 60'' (61,
91, 122, or 152cm) wide; 58'' (147cm) high.

Posts: For 1093 Series post-to-ceiling screens only. 1-1/4'' (3cm) square. 10 ft
(305cm); cut to required height in field.

a

Minimum 8'' (20cm) wide stile recommended for ceiling-hung and floor-anchored

compartments.

b

Use outswing doors to comply with local codes requiring access for physically

disabled persons.

8'0''/244cm
or as required
up to 10'0''/305cm

X''

21''

53cm

25''

64cm

18''

46cm

1096 Series

Floor-to-Ceiling Anchored

58''

147cm

12''

30cm

As

Required

10'0''

(305cm)

Max.

21''

53cm

25''

64cm

18''

46cm

1098 Series

Ceiling-Hung

58''

147cm

12''

30cm

TYPICAL HARDWARE DETAILS

Heavy-Duty Hardware (standard)

46''

117cm

18''

46cm

58''

147cm

12''

30cm

10'0''

305cm

Max.

36''

91cm

21''

53cm

1093 Series

Post-to-Ceiling Screen

These mounting points require backing. For suggested backing methods, Bobrick Advisory Bulletins TB-32 for ceiling-hung installations and TB-46
for floor-anchored are available upon request.

42''

107cm

18''

46cm

42''

107cm

15''

38cm

1095 Series

Wall-Hung Screen 42" or 48"

12''

31cm

48''

122cm

Institutional Hardware (.67 option)

TYPICAL INSTALLATION DETAILS

Floor Leveling Device

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 8/08 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.

Front Side

Front Side

Overhead-BracingCeiling Leveling Device

Standard gaps are provided at all walls
and between components to allow for
hardware attachment.

Wall gaps are standard 1/2" to 1"

MATERIALS:

Stilesc — 3/4'' (19mm) thick, Solid Color Reinforced Composite with GraffitiOff ™ surface thermoset and integrally fused into one homogenous piece. Surface,
edge, core are to be the same color. Leveling Device: 7 gauge, 3/16" (5mm) thick, corrosion-resistant, chromate-treated, double zinc-plated steel angle leveling
bar bolted to stile; furnished with 3/8'' (10mm) stainless steel diameter threaded wedge anchor, hex nuts, lock washer, flat washers, and shoe retainers. Shoe:
18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish; 4'' (102mm) high.

®

Panels — 1/2'' (13mm) thick, Solid Color Reinforced Composite with GraffitiOff

surface thermoset and integrally fused into one homogeneous piece. Surface,

edge, core are to be the same color.

®

Doors — 3/4'' (19mm) thick, Solid Color Reinforced Composite with GraffitiOff

surface thermoset and integrally fused into one homogeneous piece. Surface,

edge, core are to be the same color.

Posts (for 1093 Series screens only) — 1-1/4'' (32mm) square tubing; 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. Floor and ceiling
connections are constructed of 18-8 S, type-304, heavy-gauge stainless steel. Furnished in 10-ft (305-cm) lengths; to be cut in field to job specifications.

Headrail (for 1092 Series compartments only) — Extruded anodized aluminum with satin finish. Enclosed construction with sloping top. Face has raised
grip-resistant edge.

Designer's Notes: Headrails with integral curtain tracks and hooks are available for compar tments without doors. Optional vinyl curtains are available.

Wall Posts — 1" x 1-1/2" (25 x 38mm) tubing; 18-8 S, type-304, 16-gauge (1.6mm) stainless steel with satin-finish. 58" (147cm) high, pre-drilled for door hardware.

Heavy-Duty Hardware (standard) — Hinges, door latches, door keepers, clothes hooks, door stop plates, and mounting brackets are constructed of 18-8 S,

type-304, heavy-gauge stainless steel with satin finish. Threaded inser ts are factory installed for securing hinges, door stop plates, and door latches. Theft-resistant,
stainless steel pin-in-head Tor x screws are furnished for door hardware and all mounting brackets. Barrel hinge is adjustable to adjust door swing of unoccupied
toilet compartment from partially open to fully closed. Toilet compartment door is locked from inside by sliding door latch into keeper. Threaded inser ts are
factory installed to secure door hinges, latch and door stops. Two door stops prevents door from being kicked in/out beyond stile by vandals. Mounting screws
for stile to panel bracket, latch keeper, and coat hook connections are through-bolted.

Institutional Hardware (.67 option) — Hinges, door latches, door keepers, clothes hook, U-channels, door stop plates and angle brackets are constructed
of 18-8 S, type-304, heavy-gauge stainless steel with satin finish: one-piece, full-height hinge is 16 gauge (1.6mm); one-piece door keeper is 11 gauge (3.2mm);
one-piece, full-height U-channels and angle brackets are 18 gauge (1.2mm). U-channels secure panels to stiles, and angle brackets secure panels and stiles to
walls. Door latch slides on a shock-resistant nylon track. Two door stops prevent door from being kicked in/out beyond stile by vandals. Theft-resistant, stainless
steel pin-in-head Torx screws are fur nished for door hardware, U-channels, and angle brackets. Doors are equipped with a self-closing hinge. Threaded inserts
are factory installed to secure door hinge, latch, and doorstops. Mounting screws for stile-to-panel brackets and latch keeper connections are through-bolted. To

specify institutional hardware, add suffix .67 to series number. Example: specify 1092.67 for overhead-braced partitions furnished with institutional hardware, including
factory-installed threaded inser ts for door hardware attachment.

INSTALLATION:

Bobrick installation instructions are packed with each shipment and are available also in advance on request.

Notes:

1. Ceiling-hung and floor-to-ceiling toilet compar tments require structural members (not furnished by Bobrick) in ceiling. For suggested types of ceiling support
systems, see Bobrick Advisory Bulletin TB-32.

2. Wall backing is required to secure the mounting brackets of panels, stiles, and wall posts. For suggested wall backing, see Bobrick Advisor y Bulletin TB-46.

3. Floor-anchored stiles are furnished with expansion shields and threaded rods. The expansion shields require minimum 2'' (50mm) penetration into minimum
3'' (75mm) thick structural concrete.

4. Bobrick stainless steel partition-mounted washroom accessories are available for mounting in panels between two compartments. See current Bobrick Catalog
for description of accessories. Cutouts in panels can be pre-cut for Bobrick models at factory if location and size of all cutouts and Bobrick model numbers are
furnished at time of order.

GUARANTEE:

Bobrick toilet partitions including all hardware and mounting brackets are guaranteed to be free from defects in material and workmanship for a period of one
year from date of purchase. Any products returned to Bobrick under this guarantee will be repaired or replaced at no charge. 10-Year Warranty: Bobrick ex-
tends a ten-year limited warranty from date of purchase for SierraSeries

®

Solid Color Reinforced Composite partition panels, doors, and stiles against breakage,

warpage, delamination and corrosion when materials are properly installed, and normally used.

SPECIFICATION:

Water-resistant, solid color reinforced composite ____________________ (insert one: toilet partitions, dressing compartments, shower dividers, urinal screens)
shall be _______________ (insert one: overhead-braced toilet partition or floor anchored, wall-hung, post-to-ceiling urinal screens). Stiles, panels and doors shall
be constructed of Solid Color Reinforced Composite with GraffitiOff

®

surface thermoset and integrally fused into one homogeneous piece. Surface, edges and
core are to be same color. Solid Color Reinforced Composite material shall be covered by a 10-year limited warranty against breakage, warpage, corrosion, and
delamination. Stiles and doors shall be 3/4'' (19mm) thick; panels shall be 1/2'' (13mm) thick. All units shall meet ICC and NFPA Class B or UBC Class II, ASTM
E 84 Fire-Resistance Standards. Stiles shall have leveling device that is concealed by a one-piece, type-304, satin-finish stainless steel shoe that is 4'' (102mm) high.
Stiles, panels and doors shall be __________ (insert color name and number from current Bobrick catalog). Headrails for overhead-braced compartments shall
be anodized aluminum with satin finish.

**

All door hardware and mounting brackets shall be type-304 stainless steel with satin finish. All doors shall be supplied
with three hinges. Threaded inserts shall be factory installed for securing door hinges, latches and door stops. Theft-resistant, stainless steel pin-in-head Torx
screws shall be furnished for door hardware and all mounting brackets. Through bolts shall be used for securing latch keeper, clothes hook and panel-to-stile
brackets. A clothes hook shall be furnished for each door with heavy duty hardware option. Hinges shall be adjustable to hold doors of unoccupied compar tments
partially open or fully closed. Two door stops shall be furnished for each door to prevent it from being kicked in/out beyond stile by vandals. Manufacturer's
service and par ts manual shall be provided to the building owner/manager upon completion of project.

**

To specify Institutional hardware, replace end of specification paragraph with: .67 option All door hardware, U-channels, and angle brackets shall be type-304
stainless steel with satin finish: one-piece, full-height hinges shall be 16 gauge (1.6mm); one-piece door keepers shall be 11 gauge (3.2mm); one-piece, full-height
U-channels and angle brackets shall be 18 gauge (1.2mm). U-channels shall be furnished to secure panels to stiles, and angle brackets furnished to secure panels
and stiles to walls. Doors shall be equipped with a self-closing hinge. Two door stops shall be furnished for each door to prevent it from being kicked in/out beyond
stile by vandals. A clothes hook shall be furnished for each door. Theft-resistant, stainless steel pin-in-head, Torx screws shall be furnished for door hardware,
U-channels, and angle brackets. Through bolts shall be used for securing latch keeper and panel- to-stiles brackets. Threaded inserts shall be factory installed to
secure all door hinges, latches, and doorstops. Manufacturer's service and parts manual shall be provided to the building owner/manager upon request.

_________________ (insert one: Toilet Partitions, Dressing Compartments, Shower Dividers, Urinal Screens) shall be ____________________ Series
(insert series number) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, Califor nia; Bobrick
Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. 1090 Revised 8/08 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.