Blomberg DUS 2040 X, DUS 2042 X, DUS 5042 X Instruction Manual

Cooker Hood Dunstabzugshaube Hotte
DUS 2040 X DUS 2042 X DUS 5042 X
Instructions Booklet Bedienungsanleitung Mode d’emploi
Our Dear Customer,
We wish our product, which has been produced in modern facilities and which has been passed through strict quality control to provide you the best efficiency. For this, we kindly request you to read the whole of this guide very carefully before using your prduct and to keep it as a source of reference.
Section 1 : The points that you need to pay attention before using your aspirator and safety precautions.
Section 2 : Technical properties of your aspirator.
Section 3 : Installation of your aspirator.
Section 4 : The use of your aspirator.
Section 5 : The information in relation to the maintenance cleaning and transportation.
1
SECTION 1 : The points that you need to pay attention before using your aspirator and safety precautions.
Please do not plug in your aspirator before completing its installation.The operating voltage is 200 240 volts.The preparation of the place and the electrical installation of the product is
on the customer's account.
Please do not make connection to those stacks to which the stoves are connected to,
to the stacks where waste gas is discharged or to those stacks where flames rise.
The height between the lower surface of your aspirator and the upper surface of the
oven / range should not be less than 65 cm for electrical ranges and should not be less than 75 cm for the gas ranges or for the mixed ranges.
Do not operate your aspirator without filter. Do not take out the filters while your
aspirator is operating.
Do not touch the bulbs of your aspirator after you operate the lamps for a long period.
The hot bulbs may burn your hands.
Please check your aspirator once a while while frying. Overheated oil may create
danger by splashing your aspirator.
Flaming risk may happen at your aspirator in case periodical cleaning is not made.Please do not form high flames under your aspirator. Otherwise fire may burst out by
the flaming of the oils on the aluminum filters.
Do not keep the flame on any of the ranges of the range while the aspirator is
operating in case you using a gas range. Certainly turn off the range when you remove the food container from the range. We advise you to turn off the range before taking the food container out from the range.
Please operate your aspirator after you put the pot or fan on the range(s).Please operate your aspirator for a while, after the cooling or frying work is finished
for the good cleaning of the air in the kitchen from odors and from the vapours that are being formed while the dish is cooked.
Please provide fresh air to the medium especially while the gas ranges are used
simultaneously with the aspirator.
Please keep the packaging materials away from the reach of children since these
may form a hazard.
The length of the stack connection tube (flue) may be as long as 4 to 5 metres in
case no bend or elbow is made during the installation. The use of your aspirator with a carbon filter is advised for internal use in case there is an obligation for the flue to be longer than 5 meters.
Please make sure that your children do not play with this piece of equipment. Please
do not let the small children to use the aspirator.
Our company will not be responsible due to the problems that originate from not
complying with the above warnings.
This product has been designed for being used in homes.Please apply to the closest Beko Authorized Service to you for the installation of
your aspirator.
2
SECTION 2 : Technical properties of your aspirator.
1. Screen glass
2. Motor Command switch
3. Screen glass holder
4. Panel with holes (filter protection panel)
5. Panel with holes hatch
6. Lamp / illumination glass
7. Aluminum filters
8. Aluminum filter locks
DUS 2040 X
Width
Depth
Height
Feed Voltage
Capacity
Command
Motor power
Lamp power
Total power
Air disharge tube diameter
Net weight
The values shown in the markings on the product or the values given in the printed matter delivered together with the product are the values attained under the laboratory medium in accordance with the related standards. These values may change in accordance with the conditions of usage or in accordance with the conditions of the environment.
Usage Lifetime : 10 years (the spare parts availability period for the product)
598 mm
490 mm
150 mm
220-240V-50Hz
300 m³ / hr
3 Stage, sliding
1 x 140 W
1 x 40 W
180 W
120 mm
7,5 kg
DUS 2042 X
598 mm
490 mm
150 mm
220-240V-50Hz
450 m³ / hr
3 Stage, sliding
2 x 125 W
2 x 40 W
300 W
120 mm
8,49 kg
DUS 5042 X
598 mm
490 mm
150 mm
220-240V-50Hz
450 m³ / hr
3 Stage, sliding
2 x 125 W
2 x 40 W
300 W
120 mm
8,49 kg
3
SECTION 3 : Installation of your aspirator.
Your aspirator may be installed on your kitchen furniture (Figure 1)
Template
Tube hole
Shelf in the cupboard
Upper installation holes
(min.)
(Figure 1)
Tube Adapter
Installation on the cupboard that has been previously drilled :
Please make connection under the cupboard by making use of the 4 each 4.2 x 45 mm screws (given together with your aspirator) through the previously drilled holes. In such case, there is no need to dismantlethe filter protection panel / casette filter.
Installation un the cupboard, which has not been drilled :
Please drill 4 each connection holes by making use of the paper template that is being furnished together with the aspirator and please apply the above instructions.
4
Usage Method
Your aspirator may operate to discharge the sucked air to outside medium (by being connected to a stack) and may also operate in compliance with internal recirculation (with carbon filter). All kitchen aspirators operate in a more efficient manner with being connected to a stack. However, the operation of the aspirator at the internal recirculation position may prove to be more economical during winter for not disharging the heat in the medium to outside.
Usage With Stack Connection
Please open the filter protection cover of the aspirator. Put the selective switch on the DUCTING position (Figure 2). There are connections on and at the rear side of your aspirator for discharging air to outside in order to be able to make connection to the stack (Figure 3). Please install the 120 mm diameter tube connection part, which is being furnished together with your aspiratorin such a manner just to be fit on its place for the hatches of the tube connector. Please do not interfere anyway with the blind cap, which is present at the rear outlet under such condition. Please dismantle the blind cap from the where it is put and please install it to the top, in case you want to make a connection from the rear. Please fit the tube connection part on the place of the blind cap. Please never connect the stack connection of the aspirator while you perform the necessary procedures to a stack, which is being used for other purposes.
Usage Without Stack Connection (With Carbon Filter)
Please take the aluminum filters out. Please put the selective switch on the RECYCLING position (Figure 2). Under such condition the fitting of the carbon filter to the aspirator is needed. Please fit the carbon filter after you get in on the fixing cap (Figure 4). Please put the aluminum filters on again. Note: You may obtain the carbon filters from the Authorized Services against payment.
Figure 2
Figure 3 Figure 4
5
Uplung the product from the mains or put the switch off or untighten or close the fuse, which feeds the aspirator.
Aluminum Filter
This filter is for holding the oil particles in the air. Your cleaning the filter in normal use in intervals of 1 month long is being proposed. For this procers, first take aut the aluminum filters. Please wash the filters in water with detergent and rinse and dry them. Then please fit the filters in their places. Colour change may be observed as they are washed. Sudn a situation is normal and your replacing the filter is not necessary.
Figure 5
The Dismantling Of The Aluminum Filters
1. Please push the aluminum filter lock forward.
2. Them slightly lower it and pull forward. Otherwise you may bend the filter (Figure 5).
Please fit the aluminum filter in its place by following the above steps from the reverse.
Carbon Filter (Usage Without Stack)
This filter gets rid of cooking odours.
Attention : Carbon filter must never be washed. The carbon filter must be renewed every 4 months in normal usage. You may obtain the carbon filter from the Beko Authorized Services against payment (Please refer to page 6).
6
SECTION 4 : The use of your aspirator.
Your aspirator is commanded through a control panel, which is placed on the front panel with sliding controls (switches).
Your aspirator has 3 speed stages :
1st position : Light aspiration 2nd position : Medium aspiration 3rd position : Heavy aspiration 0 position : Motor does not operate, no aspiration occurs.
Note: The motor must be in open position for using the motor positions of DUS 2042 X and DUS 5042 X models.
Functions on the switch keys
DUS 2040 X DUS 2042 X / DUS 5042 X
Lamp
Closed
Lamp Open
Lamp Open
Lamp Open
Motor in 1st position
Motor in 1st position
Motor in 2nd position
Motor in 3rd position
Lamp
Closed
Lamp Open
Lamp Open
Lamp Open
Motor
Closed
Motor
Open
Motor
Open
Motor
Open
Motor in
1st position
Motor in
1st position
Motor in
2nd position
Motor in
3rd position
Illumination Lamp:
You may open and close the illumination lamp independent of the motor through the lamp switch on the control panel.
7
Loading...
+ 19 hidden pages