Blomberg CTE30400 Installation
Glass Ceramic Cooktop
CTE 30400
CTE 36500
Installation Instructions
Instructions d’Installation
Instrucciones de Installación
Table of
Contents
Page
Special Warnings ..............................................................
Product Dimensions
Important Preparation Suggestions.....................................
Co
oktop Installation..........................................................
Electrical Connections....................................................
General information...........................................................
3-
Wire branch circuit ......................................................... 1
4-Wire branch circuit ......................................................... 1
IMPORTANT: Save these instructions for the local electrical inspector use.
INSTALLER: Please leave this manual with owner for future reference.
OWNER: Please keep this manual for future reference.
Pay attention to these symbols present in this
manual
and Cutout Requirements.............
You can
IMMEDIATELY follow instructions.
be killed or seriously injured if you don't
DANGER
Proper installation is your responsibility. Have a
qualified technician install this cooktop.
Please read
WARNING
Special Warnings
all instructions before using this appliance
Important:
Observe all
Write down the model and serial numbers before
installing the cook top. Both numbers are on the
serial rating plate located on bottom of cooktop
box.
Before Starting Installation
governing codes and ordinances.
WARNING
the customer's responsibility to contact a
It is
qualified electrical installer. To assure that the
electrical installation is Adequate and in
conformity with national electrical code:
ANSI/NFPA 70-latest edition** or CSA standards
C22.1-94, Canadian Electrical Code, part No.0M91 - latest edition*** and all local codes and
ordinances.
Installation Manual
ENGLISH
WARNING
is is the safety alert symbol. This symbol
Th
alerts you to potential hazards that can kill or
hurt you and others.
You can be killed or seriously injured if you
don't follow these instructions.
READ AND SAVE THESE INSTRUCTIONS.
To installer:
Leave these instructions with the appliance.
To customer:
Retain these instructions for future reference.
WARNING
the information in this manual is not followed
If
exactly, a fire or explosion may result in
personal injury or death.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
Copies of the standards listed may be obtained from:
** National Fire Protection Association One Batterymarch Park
Quincy, Massachusetts 02269
*** CSA International 8501 East Pleasant Valley Rd. Cleveland,
OH 44131-5575
eliminate the risk of burns by reaching over
To
heated surface units, cabinet storage space located
above the surface units should be avoided. If he
cabinet storage is to be provided, the risk can be
reduced by installing a range hood that projects
horizontally a minimum of 5" (12,7 cm) beyond the
bottom of cabinet.
3
Installation Manual
ENGLISH
�
CTE 30400
CTE 36500
30”
(76,2 cm)
36”
(91,4 cm)
21”
(53,3 cm)
21”
(53,3 cm)
3” 1/8
(7,9 cm)
3” 1/8
(7,9 cm)
Figure 1.
Figure .
1-1/4" (3,2cm) Canadian
2-1/4" (5,7cm) US
4
Installation Manual
ENGLISH
Figure 3.
CUTOUT
WIDTH
30”
(76.2cm)
36”
(91.4 cm)
IMPORTANT
Under the cooktop it is necessary to install a partition,
spaced at least 15 mm. from the bottom of the
appliance as shown in figure 3.
Cutout dimensions and requirements
A B C D E F G
28-11/16”
(72.9 cm)
28 15/16”
(73.5 cm)
34-1/16”
(86,5 cm)
34-5/16”
(87.2 cm)
19-1/4”
(49.0 cm)
19-/”
(49. cm)
19-1/4”
(49.0 cm)
19-/”
(49. cm)
30”
(76.2 cm) min
36”
(91.4 cm) min
* NOTE
24” (61 cm) min. clearance if bottom of wood or metal cabinets is
protected by not less than 1/4“ (0.6 cm) flame retardant millboard
covered with no less than No. 28 MSG sheet steel 0.015” (0.04 cm)
stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper.
30”(76.2 cm) min. clearance between top of cooking platform and bottom
of unprotected wood or metal cabinet
Important Preparation Suggestions
1.
Chamfer all exposed edges of decorative laminate
to prevent damage from chipping.
2. Radius corners of cutout and file to Insure
smooth edges and prevent corner cracking.
Recommend 1/4“or 3/8“diameter drill In each
corner.
3. Rough edges, inside corners which have not been
rounded and forced fits can contribute to cracking
of the countertop laminate.
18” (45.7 cm)
min
Height from
countertop to
nearest
cabinet on
either side of
unit
30” (76.2 cm)
min.
(see note*)
Clearance from
countertop to
unprotected
overhead
surface
2” (5 cm) min
Clearance from
cutout to side
wall on the left
and right of the
unit
13” (33 cm)
Depth of
unprotected
overhead
cabinets
This cooktop has been designed with wide
tolerances of cut-out to cover possible
replacement with other brands. We recommend to
that you consider the minimum dimension of cutout size In the case of new Installation.
Some cut out sizes for possible replacements:
Dim.
30"
36
Inches cm
28-15/16" x 19-/"
"
34-5/16" x 19-/"
73,5 x 49,
87,2 x 49,
5
Installation Manual
ENGLISH
Cooktop Installation
WARNING
Excessive
Use two or more people to move and install
cooktop.
Failure to do so can result in back or other injury.
Cut Hazard
Beware of sharp edges. Use the polystyrene ends
when carrying the product. Failure to use caution
could result in minor injury or cuts.
Always consult
specific instructions.
Ensure the countertop is square and level and
ensure no structural members interfere with space
requirements.
Prepare the cut-out according to the instructions
(see cut-out dimensions).
Make sure the wall coverings, countertop and
cabinets around the cooktop can withstand heat
(up to 200 °F / 93 °C).
Weight Hazard
the countertop manufacturer for
Step 1
Remove
packaging materials and literature package
from the cooktop before beginning installation.
Remove Installation Manual from literature pack and
read them carefully before you begin.
MANUAL
T
OP-CARDBOARD
TOP PACKAGING
GASKET
SCRAPER
TOP
COOK
BOTTOM PACKAGING
CARDBOARD
Figure 4. Tools you will need
6
Figure 5. Parts
Step 2
Place
a towel or table cloth onto the counter top. Lay
the cooktop upside down onto the protected surface.
gure 6.
Fi
Installation Manual
ENGLISH
Step 3
A foam tape is provided to seal the cooktop edges to the
countertop. Apply tape approximately 1/16” (1.5 mm)
from the glass edge to the underside of the cooktop
glass. Use tape around the entire glass perimeter. Cut
off excess where tape ends butt.
Figure 7
Step 4
Insert the cooktop centered into the cutout opening.
Make sure the front edge of the counter top is parallel
to the cooktop. Make nal check that all required
clearances are met.
Step 5
Four clamp brackets are provided to clamp the cooktop
to the countertop. Tighten screws just enough to hold
brackets in place when cooktop is put into cutout.
Tighten screws securely.
Figure 9
Figure 8
7
Installation Manual
ENGLISH
Figure 1.
Figure 1.
WARNING
THE CONDUIT IS 3 FEET LONG
The junction box, must be located where it will
allow considerable slack in the conduit for
serviceability.
Important:
For solid surface material installations such as
Surel™ and Corian®, consult with solid surface
manufacturer. Apply heat reflective tape such as
Scotch® Aluminum Foil Tape #425 or #427
around the cutout so that it folds over on the top
and sides.
Do not wrap the tape underneath the cooktop.
Be sure the tape extends beyond the outermost
flange of the cooktop. All corners should be
covered with tape.
8
Installation Manual
ENGLISH
Electrical Connections
Disconnec
DANGER
t power before servicing the product.
Failure to do so could result in death or
electrical shock.
General information
WARNING
The models may be powered at 240V or
208V.
This coo
the cooktop is to be completely enclosed in a cabinet,
feed the cooktop cable through the opening in the
cabinet. Make the electrical connection following the
appropriate steps for your installation.
Your cooktop must be connected to the proper
electrical voltage and frequency as specified in the
table on the right.
ktop does not require a neutral connection. If
The flexible conduit (supplied) 3 feet long (100 cm)
located at the right rear of the cooktop bottom box
should be connected directly to junction box. Do not
cut the conduit. A U.L - or CSA - listed conduit
connector must be provided at each end of the power
supply cable (at the cooktop and at the junction box.)
A time delay fuse or circuit breaker is recommended.
Do not ground to a gas pipe. Do not have a fuse in the
grounding or neutral circuit.
Fuse both supply (phase) lines.
WARNING
proper connection of aluminum house wiring to
Im
the copper leads can result in a serious problem.
Power Supply
240 V 60 Hz 208 V 60 Hz
7,1kW 29,6A 5,33kW 25,6A
9,9kW 41,3A 7,43kW 35,8A
Approval
code
512T40NH
512V50ND
30”
CTE 30400
36”
CTE 36500
Model
AG
SERIAL T
Figure 12. Location of serial tag
nnect with copper wire only
Co
If the house has aluminum wiring, follow the
procedure below:
1. Connect the aluminum wiring to the copper wire
by using special connectors designed and
Underwriters Laboratories-listed for joining copper
to aluminum. Follow the electrical connector
manufacturer's recommended procedure.
2. Aluminum/copper connection must conform with
local codes and industry- accepted wiring
practices.
National
Batter/march Park Quincy, Massachusetts 02269
Fire Protection Association
A three-wire, single phase, 240 Volt 60 cycle electrical
system (properly circuit protected to meet Local
Codes of NFPA No.70) must be provided. Unit must
be properly grounded in accordance with local wiring
code. The chart below recommends the minimum
circuit protector and wire size if the appliance is the
only unit on the circuit. If smaller sizes of wire are
used, the unit efficiency will be reduced and a fire
hazard may be created. It is advisable that the
electrical wiring and hookup be accomplished by a
competent electrician.
9
Loading...