Blomberg CEA 2211 X Instruction Manual

CEA 2211 X

Instruction manual

Built In Coffee Machine

Please read this manual first!

Dear Customer,
We hope that your product, which has been produced in modern plants and

checked under the most meticulous quality control procedures, will provide you
an effective service.

For this, we recommend you to carefully read the entire manual of your product
before using it and keep it at hand for future references.

This manual

• Will help you use your appliance in a fast and safe way.

• Read the manual before installing and operating your product.

• Follow the instructions, especially those for safety.

• Keep the manual in an easily accessible place as you may need it later.

• Besides, read also the other documents provided with your product.

Please note that this manual may be valid for other models as well.

Disposal of electrical appliances

European Directive 2002/96/CE on electrical waste and electronic
equipment (WEEE) requires that electrical appliances not be
disposed of as unsorted municipal waste. Used appliances must be
collected separately to optimize the reclamation or recycling of the
component materials and prevent potential harm to human health
and to the environment.

The symbol of the cancelled garbage bin is displayed on all these products to
remind users of the obligation of separate collection. For further information on
the correct disposal of electrical appliances, please contact your local authorities
or the retailer.

Disposal of electrical appliances 2

1 Machine description 2

Front and overall view 2
Control buttons and display panel 2
Important safefguards 3
Safety instructions and warnings 3
Correct use 4
Technical safety 4
Use 5
Save these instructions 6
Correct use 6
Technical safety 6
Usage safety 7

2 Desciption and operation 9
3 Installation 10
4 Important ınstructions for first time use! 13
5 Adding water and coffee beans İn the respective containers 14

Filling the water tank 14
Filling the coffee bean container 14

6 Removing coffee grounds and water 15
7 Operation and use 16

Programming the machine 16
Automatic switch-on 16
Automatic switch-off 17
Auto shut down 17
Energy savings 17
Display language 17
Water hardness 17
Descaling 17
Ground coffee quantity 18
Coffee temperature 18
Steam temperature 18
Setting the grind 18
Coffee counter 18

Selecting the type of espresso 19

Adjusting the espresso dose 19

8 Preparing the beverages 20

Cleaning 20
Preparing espresso 20
Steam 20
Preparing cappuccino 20

9 Care and cleaning 22

Water tank 22
Steam dispenser 22

10 Descaling the machine 23
11 Trouble-shooting 24

Auto-diagnostics 24
Technical service 24
Water pressure 24
Grinder 24

12 Technical Data 25

Contents

EN

2

1 Machine description

Front and overall view

Control buttons and display panel

1. Lighting 10. Short, medium, or long coffee selector

2. Steam dispenser 11. Coffee dispensing button

3. Drawer handle 12. Steam selector

4. Coffee dispenser 13. "cleaning" button

5. Water tank 14. Display

6. Drip grille 15. Grind adjuster

7. Container for coffee beans 16. Attention

8. On/Off button 17. Main switch

9. 1 cup/2 cup selector

EN

3

Important safefguards

Safety instructions and
warnings

This machine complies with
current safety regulations. The
appliance is not to be used by
persons (including children) with
reduced physical, sensorial or
mental capacities, or without
experience or knowledge, unless
they benefit, through a person
responsible for their safety,
of surveillance or instructions
regarding the use of the appliance.
Children must be overlooked to
ensure they do not play with the
appliance. Read these instructions

carefully before using the machine.
They contain important information
on safety, use and maintenance,
to provide protection and to avoid
damages to the machine.

1. Read all instructions

2. Do not touch hot surface, use
handles or knobs

3. To protect against fire, electrical
shock and injury to persons do not
immerse cord or plugs in water or
other liquid

4. Close supervision is necessary when
any appliance is used by or near
children.

5. Unplug from outlet when not in use
and before cleaning. Allow unit to
cool before putting on or taking
off parts, and before cleaning the
appliance.

6. Do not operate any appliance with
damaged cord, plug, after the
appliance malfunctions, or has been

damaged in any manner. Return

appliance to the nearest authorized
service facility for inspection, repair or
adjustment

7. The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electric shock or injury

8. Do not use outdoors

9. Do not let cord hang over edge
of table or counter, or touch hot
surfaces

10. Do not place on or near a hot gas or
electrical burner, or in a heated oven

11. Always attach plug to appliance first,
then plug cord into the wall outlet. To
disconnect, turn any control off. Then
remove plug from wall outlet.

12. Do not use appliance for other than
intended use

13. To reduce the risk of fire, do not
place any heating or cooking
appliance beneath the appliance

14. To reduce the risk of fire, do not
mount unit over or near any portion
of a heating or cooking appliance

15. To reduce the risk of electrical shock,
do not mount over a sink

16. To reduce the risk of fire, do not
store anything directly on top of
the appliance surface when the
appliance is in operation.

EN

4

Correct use

• This machine is designed solely for

preparing espresso, cappuccino,
long coffee and for boiling water for
tea and other hot drinks. Other types
of use are not permitted and may
prove dangerous. The manufacturer
will not be held liable for any damage
caused by incorrect use of the
machine.

Technical safety

• Before connecting the machine to the

electricity supply, check the electrical
information (voltage and frequency)
on the data sheet with that of the
electricity supply thoroughly.

• This data should be exactly the same

to avoid damaging the machine. In
case of doubt, contact a qualified
electrician.

• The electrical safety of the machine

is only guaranteed if it is connected
to a regulation earth wire. It is very
important to check this carefully. In
case of doubt, have the electricity
supply checked by a qualified
electrician.

• The manufacturer will not be

held liable for any harm or
damage caused due to a lack or
malfunctioning of the earth wire (e.g.
risk of electric shock).

• Only operate the machine when

installed so as to avoid contact with
electric parts. For the assembly,
dismantling and daily maintenance
of the machine, always make sure
it is disconnected from the electrical
supply.

• The machine should not be

connected to the electrical supply

with extension cables, as these do

not provide the necessary safety
for the machine (e.g. danger of
overheating).

• The machine may also be built into a

cabinet (special accessory). It is not
suitable for outdoor use. Due to the
weight of the machine, the cabinet
must be secured firmly to the wall.

• Installation, maintenance and repair

works must only be carried out by
qualified persons. Any installation,
maintenance and repair works
carried out incorrectly may cause
considerable danger to the user,
for which the manufacturer will not
assume any liability.

• The machine should only be

disconnected from the electrical
supply when:

- The main switch of the electrical
supply is disconnected;

- The fuse for the house electrical
supply is removed;

- The plug to the machine is taken
out of the electrical socket. To
disconnect the machine from the
electrical supply, unplug without
pulling on the cable.

“TO REDUCE THE RISK OF INJURY,
DO NOT DRAPE CORD OVER THE
COUNTER TOP OR TABLE TOP
WHERE IT CAN BE PULLED ON
BY CHILDREN OR TRIPPED OVER
UNINTENTIONALLY”

POWER CORD HAS TO BE: UL
approved, type SJO/SJT 16AWGx3C
moulded plug, max length 4-1/2ft

(1.4Mt)

EN

5

• A short power-supply cord (or

detachable power-supply cord) is to
be provided to reduce risks resulting
from becoming entangled in or
tripped over a longer cord.

• Longer detachable power-supply
cord or extension cord are available
and may be used if care is exercised

in their use

• If a long detachable power-supply
cord or extension cord is used

the marked electrical rating of the
detachable power-supply cord or

extension cord should be at least as

great as the electrical rating of the
appliance.

• If the appliance is of the grounded
type, the extension cord should be a

grounding-type 3-wire cord.

• The longer cord should be arranged

so that it will not drape over the
counter op or table top where it
can be pulled by children or tripped
over. An appliance that utilizes a
detachable power-supply cord shall
be provided with: the appropriate
detachable power-supply cord as
indicated in supply connections,
instructions that advise the consumer
that the appropriate detachable
power-supply cord is not provided,
and specify which detachable power­supply cord or cords are appropriate.
If long and short de-tacable power­supply cords are available, the
instructions shall include information
regarding the problems attendant
with each.

• Under no circumstances should

the machine casing be opened.
Touching the voltage cables
or changing the electrical and
mechanical structure may cause
danger of electric shock. It may also
affect the operation of the machine.

The manufacturer declines all

responsibility for persons or
property if the above instructions
are not observed in full.

• If the machine is to be installed

with other appliances, it must be
separated from them with a shelf.

Use

Warning! Danger of burning!
Liquids leaving the dispensers are
boiling!

• Children should only use the machine

while under supervision. Children’s
skin is more sensitive to high
temperatures.

They may burn themselves!

Remember too that espresso coffee

is not a children’s drink.

• When using the machine for the first

time, rinse the pipes to get rid of any
deposits and to ensure hygiene.

• Only fill the water tank with drinking

water at room temperature or chilled.

Hot or boiling water or any other

liquid may damage the operation of
the machine. It is advisable to replace
the water daily to prevent bacterial
growth.

• Only pour coffee beans into the

coffee container. If ground coffee
is poured into the container, it may
damage the grinder.

EN

6

• Sugar damages the machine!

Do not fill the machine with coffee

beans treated with caramel, sugar or
similar substances, instant coffee or
other substances containing sugar.

• Boiling water and steam may cause

burning, so these functions should
be performed with the utmost care.

Never direct the steam dispenser

towards parts of the body. It may
cause burning!

• Always ensure that the steam

selector is disconnected when no
steam is required, otherwise, steam
may escape unintentionally. It may

cause burning!

• The water/steam dispenser gets

very hot during use. Only hold the
dispenser by the handle. It may

cause burning!

• Depending on the lime content of

the water, the machine should be
descaled regularly with a citric acid
solution. In areas of very hard water,
the water pipes should be descaled
more frequently.

The manufacturer will not be held

liable for any damage caused by
inadequate descaling.

Follow the mixing instructions

indicated on the descaling pack.
Otherwise, the machine may get
damaged.

• Do not lean on the open drawer

of the coffee machine, as this may
damage the machine.

• If the coffee machine is installed near

an oven with a self-cleaning function,
disconnect the coffee machine
during self-cleaning, otherwise it may
get damaged.

The manufacturer cannot be held

liable for any damage caused
by failure to observe the safety
instructions and warnings.

Save these instructions

This machine complies with the safety
regulations currently in force. Incorrect
use of the machine may lead to
personal injury and damage to objects.

Please read all the instructions
carefully before using the machine as
they contain important information on
safety and the use and maintenance of
the machine. This will protect you and
prevent damage to the machine.

Correct use

• The machine is designed exclusively

for preparing espresso and
cappuccino, as well as boiling water
for tea and other hot beverages.
Other types of use are not
permitted and could be dangerous.
The manufacturer declines all
responsibility for damage caused by
improper and/or or incorrect use of
the machine.

Technical safety

• Before connecting the machine to

the power mains, check carefully
to make sure that the voltage and
frequency ratings shown on the
rating plate correspond to those of
the electrical system. These values
must absolutely correspond in order
to avoid damage to the machine. In
case of doubt, contact a qualified
electrician.

EN

7

• The electrical safety of the machine is

guaranteed only if it is connected to
a standard earth conductor. It is very
important to verify this information
with the utmost attention, and in case
of doubt have the electrical system
checked by a qualified electrician.
The manufacturer declines all
responsibility for any damage
caused to people or things due to
the lack or malfunction of the earth
conductor (for example: risk of
electrocution).

• Put the machine into operation only

after complete installation in order
to avoid contact with the electrical

components. Before carrying out

assembly, disassembly, or daily
maintenance of the machine, always
make sure to disconnect the power
cable from the electrical outlet.

• The connection of the machine to

the power mains must not be made

using extension cables, as they do

not guarantee the necessary safety
of the machine (for example: risk of
overheating).

• The machine can also be flush-

mounted in a wall unit (special
accessory). It is not suitable for
outdoor use. Considering the heavy
weight of the machine, it is essential
for the unit to be adequately secured
to the adjacent wall.

• If the power cable is damaged,

it must be replaced by the
manufacturer, its technical service, or
by a qualified electrician, in order to
prevent any risk.

• All installation, maintenance, and

repair operations must be carried out
by qualified personnel only. Incorrect
installation, maintenance, and repairs
may lead to serious dangers to the
user, for which the manufacturer
declines all responsibility.

• The machine is disconnected from

the power mains only when:

- the main switch of the electrical
system is switched off;

- the fuse of the home electrical
system is completely disconnected;

- the power plug of the machine
is completely removed from the
electrical outlet.

To disconnect the machine from the

power mains, grasp the plug and
remove; do not pull on the power
cable.

• Do not open the machine casing for

any reason. Touching the voltage
cables or modifying the electrical or
mechanical structure may lead to
electrocution. This could also cause
disturbance in the operation of the
machine.

The manufacturer declines all

responsibility towards persons or
things due to failure to observe
the instructions above.

• In the event that the machine has

to be installed in combination
with another appliance, it must be
separated from the other appliance
by a solid intermediate shelf.

Usage safety

Warning! Danger of burning!
The liquids that come out of the
dispensers are extremely hot!

EN

8

• Children may access the machine

only under adult supervision.
Children’s skin is more sensitive
to high temperatures. Danger of

burning!

Remember, too, that espresso

coffee is not a suitable beverage for
children.

• The first time the machine is put into

operation, it is necessary to rinse the
pipes to eliminate any deposits and
to ensure hygiene.

• Fill the water tank only with room

temperature or cold potable water.

Hot or boiling water or any other

liquid can damage the operation
of the machine. We recommend
changing the water daily to prevent
the germ proliferation.

• Place only whole coffee beans in

the coffee container. Ground coffee
poured into the container can
damage the operation of the grinder.

• Sugar damages the machine!
Never use coffee beans that are

treated with caramel, sugar, or other
similar substances, instant coffee, or
any substances containing sugar.

• Boiling water and steam can cause

burning; therefore, please use these
functions with the utmost attention.
Do not turn the steam dispenser
towards any parts of your body.

Danger of burning!

• Always make sure that the steam

selector is disengaged when steam is
not needed. Otherwise, steam could
be dispensed inadvertently. Danger

of burning!

• The steam dispenser becomes very

hot during use. Grasp the dispenser
only by the coupling. Danger of

burning!

• Depending on the lime content of

the water, the machine should be
descaled regularly using a liquid
solution of citric acid. In zones where
the water is very hard, it will be
necessary to descale the water pipes
more often.

The manufacturer declines all

responsibility for any damage
caused by insufficient descaling.

Follow the mixture ratio indicated

on the package of the descaling
product; otherwise the machine
could be damaged.

• Do not put weight on the open door

of the coffee machine, as this could
damage the machine.

The manufacturer declines all

responsibility for any damage
caused by failure to follow
the safety instructions and
precautions.

EN

9

2 Desciption and operation

The coffee machine has two water
heaters, one for the water and one for
the coffee.

Differently from the norm, in this
espresso machine the beans can
be ground at the moment and only
when necessary. This provides the
best aroma of the coffee because it is
freshly ground.

If the container used, glass or cup,
has a smaller volume than the dosage
programmed by the machine, coffee
dispensing can be interrupted at any

time by pressing key “11” (Fig. 1A/1B),

allowing the user to decide on the
preferred dose.

The grinding level can also be set,
choosing a coarser or finer grind
depending on user preference, by
turning the dial situated on the left side
of the machine.

The steam from the dispenser can also
be used for pre-heating the cups.

Fig. 1A

Fig. 1B

EN

10

3 Installation

The installation of the appliance must

be carried out exclusively by qualified

personnel in compliance with the
regulations in force. Considering the
heavy weight of the machine, it is
essential that the furniture unit be
suitably secured to the wall.

1. Check to make sure that the

opening for housing the machine has

the correct dimensions (Fig.2A/2B).

Fig. 2A

595 mm (23

7/16

”)

560 mm (22”)

600 mm (23

5/8

”)

542 mm (20”)

436 mm (17

1/4

”)

440 mm (17

3/4

”)

445,4 mm (18”)

320 mm (11”)

19 mm (23

3/4

”)

Min 320 mm (12

3/8

”)

EN

11

2. Remove the machine from the base

by unhooking it from the lateral
guides using the levers (Fig. 3). raising
the lever of the right-hand guide and
lowering the lever of the left-hand
guide (1).

3. Slide the base of the machine into
the unit all the way back (2).

4. Attach the base to the shelf using the
10 holes and the screws provided
(Fig.4).

Note : If the sides of the base are not

flush with the sides of the unit, use
the shims provided (3).

5. Close the machine guides all the
way.

6. Connect the plug to the power outlet
following the safety regulations in
force. Important: The power outlet
must be accessible after the machine
has been installed.

7. Insert the machine in the unit, taking
care that the machine guides are
correctly inserted in the guides on
the base, and slide the machine
in leaving the necessary space for
reaching and connecting the power
plug.

8. Close the machine by sliding it all the
way back.

9. Fill the water tank and the coffee
container.

10. Supply power to the machine using
the main switch situated on the left
side of the machine (page 3 Fig. 18)

The manufacturer declines any
responsibility towards persons or
objects, as well as for the proper
operation of the machine, due to
failure to follow the instructions
given above.

EN

12

Fig. 4

Fig. 3

EN

13

4 Important ınstructions for first time use!

Instructions additional to the
instruction booklet, which must be
read prior to using the machine.

The manufacturer declines all
responsibility for damage caused by
improper or incorrect use and failure
to follow the instructions provided in
the instruction booklet and given here
below.

1. Extract the machine by lifting the

handle of the drawer and pulling it
towards you.

2. Fill the water tank and the coffee
container following the instructions on
page 10 of the instruction booklet.

3. Supply power to the machine using
the main switch (18) located in the
upper part of the left side of the
machine.

4. Close the machine.

5. Switch on the machine using the
key

If a failure is signalled, turn the main
switch off and back on to help the
water circuit fill up.

6. The machine is now ready for use.

EN

14

5 Adding water and coffee beans İn the respective

containers

The water tank needs to be refilled
when the display shows:

Filling the water tank

Filling the coffee bean
container

The coffee bean container needs to be
refilled when the display shows:

To ensure the best result in making
espresso, in addition to using good
quality coffee, it is also essential to use
good water. We therefore recommend
emptying the water tank frequently
and refilling it with fresh water. Avoid
leaving the water in the tank for

excessively long periods.

IMPORTANT: Use only cold potable
water with hardness less than 7°F.

• Open the machine by raising the

drawer handle and pulling outward.

• Fill the tank up to 4 cm (1 9/16 inches

from the top).

• Close the machine.

N.B. When the water tank is almost
empty, the message “ WATER LOW “

will appear on the display panel

Note: The tank can be removed for

cleaning.

Fill the coffee bean container using
only beans for espresso coffee.

Any other substance, including ground
coffee, can damage the coffee grinder.

Do not use beans treated with
caramel, sugar, or similar substances,
instant coffee, or any beverage
containing sugar. Sugar can damage
the machine.

• Open the machine by raising the

drawer handle and pulling outward.

• Remove the lid of the coffee bean

container.

• Fill the container with beans up to 2

cm (3/4 inches) from the top.

• Put the lid back on the container.

• Close the machine.

EN

15

6 Removing coffee grounds and water

After twenty coffees have been made,

the message “COFFEE GROUNDS”

will appear on the display.
The container should be emptied. After

this message appears, the machine
will allow 5 more coffees to be
prepared and then it stops.

IMPORTANT
The container must be emptied

regularly to prevent the formation
of mould and bacteria.

1. Open the drawer A.

2. Remove the grille B.

3. Extract and empty the coffee

grounds container C and the water
container D.

4. Place the two containers and the
grille back in their seats.

5. Close the drawer.

6. Press the key

for about 3

seconds until you hear the beep of

confirmation. Now the machine is

ready for use again.

IMPORTANT:
ALWAYS EMPTY THE GROUNDS

CONTAINER

C

B

A

D

EN

16

7 Operation and use

Switch-on

Switch the machine on using the key

.

After a few seconds, the following
message appears on the display panel:

Welcome message

During the heating phase, the words

COFFEE and WATER flash. The

machine is ready for use only when
they have stopped flashing.

The display also shows the type of
coffee selected (short/medium/ long)
as well as the choice of making one or
two coffees at the same time.

Programming the machine

Various functions can be adjusted and

programmed, as indicated below:

To enter programming mode, with
the machine off press the key

for 3

seconds until the display panel shows:

Use the keys to select the
functions to be programmed, which
are, in order of appearance:

Pressing the key the display
panel shows:

Use the keys to set the hour.
Initially the two digits related to the
hour flash.

After setting the hour, press the key

.

The two digits related to the minutes
flash. Set the minutes by pressing the
keys

.

Automatic switch-on

Press the key and the display
panel shows:

Use the keys to set the time
you want the machine to switch on
automatically.

Automatic switch-on can be activated
or de-activated by pressing the key
(with the machine off). The display will

show an * next to the time

EN

17

Automatic switch-off

Press the key and the display
panel shows:

Use the keys

to set the minutes
(15,30.45.60.75,90 min) after which
the machine goes into “energy

savings” mode. In this phase, the

temperature of the water heater is
lowered to reduce consumption.

Press the key to restore the
machine to a ready status quickly.

The display shows the number of litres
of water that have been dispensed
and the theoretical level of lime scale

build-up expressed as a percentage

(100% indicates that you need to
carry out descaling). This parameter
is calculated based on the water
hardness and the number of litres
of water dispensed. The lime scale
indicator will reset after a descaling
cycle has been carried out.

Use the keys

to set the time
you want the machine to switch off
automatically.

Auto shut down

Press the key and the display
panel shows:

Use the keys

to set the
minutes (15-30-45-60-75-90 min)
after which the machine switches off
automatically. 0=OFF.

Energy savings

press the key and the display
panel shows:

Use the keys

to set the hardness
of the water after using the special
measuring kit to establish the correct
number (0,5,10,15,20,25°dh) to be
entered. (1°dh=1.786°F=1.250°e=

17.86ppm=0.1786mmol/lt)

Descaling

Use the keys to select the
desired language. Available languages
are English, Spanish, Italian, French
and German.

Water hardness

Press the key and the display
panel shows:

Display language

Press the key and the display
panel shows:

EN

18

Ground coffee quantity

Press the key and the display
panel shows:

Using the keys

you can change

and set the temperature
of the steam. The scale of variation

ranges 14° to +50° F (-10 °C a +10
°C). The 0 position corresponds to the
optimal factory setting.

Press the key to exit the
programming function.

Setting the grind

A number of factors help you to
understand whether the grinding level
needs to be adjusted:

• If the coffee is dispensed too quickly,

this means that the beans have been
ground too coarsely.

• If the coffee comes out in slow drips,

this means that the beans have been
ground too finely. A very important
factor for ensuring a good coffee is
the right setting for the grinding level,
which is factory-set but can also be
modified as follows:

• Open the machine.

• Carefully turn the dial located on the

left side of the machine “A” (Fig.5).

Turning the dial clockwise produces
a finer grind; turning it anticlockwise
produces a coarser grind.

Note: Turn the dial min. 3 complete
turns, clockwise or anti-clockwise,
to obtain a change in the degree of
grinding, finer or coarser.

IMPORTANT !! After setting the
new grind, it is necessary to
dispense at least 2 coffees.

Using the keys

you can change
and set the quantity of ground coffee
to make the flavour of the coffee the
desired strength. The scale of variation
ranges from -5 to +5 (0.1 sec). The 0
position corresponds to the optimal
factory setting.

Coffee temperature

Press the key and the display
panel shows:

Coffee counter

Press the key and the display
panel shows:

Steam temperature

Using the keys you can change
and set the temperature of the coffee.
The scale of variation ranges from 14°
to +50° F (da -10 °C a +10 °C). The
0 position corresponds to the optimal
factory setting.

EN

19

Fig. 5

Using the key you can select
from among the following types of
espresso dose:

SHORT
NORMAL
LONG

Adjusting the espresso dose

To change and memorize the quantity
of coffee, proceed as follows:

• During the infusion, press and hold

the key until the desired quantity
(coffee dose) is reached.

The display shows the message

“MEMO ?”

Selecting the type of espresso

If you want to memorize the dosage of
coffee just made, proceed as follows:

Setting 1 or 2 coffees

With this machine you can prepare
a single coffee or 2 coffees
simultaneously.

Make your selection using the key

EN

20

8 Preparing the beverages

Cleaning

Before or after a long period of

inactivity, it is recommended to carry
out a washing cycle on the unit.

• Press the key for 3 seconds. The

machine carries out a washing cycle
on the unit by passing only water
through the circuit.

Preparing espresso

• Position the cup or cups under the

dispenser spout.

• Make sure that the word “COFFEE”

has stopped flashing, which means
water temperature reached.

• Press the key to start the

dispensing. Dispensing stops
automatically, but it can also be
stopped beforehand by pressing the
same key again.

Steam

• Switch on the steam for preparing

steam using the key

and wait

till the word “STEAM” has stopped

flashing.

• Position the cup or other container

under the nozzle.

• Press the steam button to dispense

the steam

.

Fig. 7

Preparing cappuccino

• Select the steam function using the

key

.

• Wait till the word “STEAM” stops

flashing on the display.

• Before positioning the container

under the steam nozzle to flush out
the water remaining in the pipes.

• Prepare a medium coffee in a

cappuccino cup.

• Fill the 50 cl jug milk with about

10 cl of milk. This is the quantity
for preparing one cappuccino. We
recommend preparing frothed milk
for one cappuccino at a time.

• Introduce the steam nozzle into the

milk container so that the spout is
positioned on the bottom of the
container (Fig. 7A).

• Turn the steam dial anti-clockwise to

release the steam and heat the milk
for a few seconds.

EN

21

• Important: Do not heat the milk

excessively. Overheated milk no
longer produces froth.

• After a few seconds, position the

spout of the nozzle at the surface of

the milk (Fig. 7B).

• When the desired froth is obtained,

close the steam tap.

• Pour the milk delicately into the cup

previously filled with coffee.

N.B.: If the machine is switched off
with the steam function activated, this
function remains in memory when it is

switched back on the next time.

Fig. 7A

Fig. 7B

EN

22

9 Care and cleaning

The appliance must not be immersed
in water or other liquids for cleaning.

Let the coffee machine cool down
before proceeding with cleaning.

Danger of burning !

Do not use steam appliances for
cleaning the machine.

Do not use any detergent substances

containing soda, acids, or chlorides!

These substances will ruin the surface
of the machine.

Regular cleaning guarantees the

efficient operation and long life of your
espresso coffee machine.

Remove the grille and tray from the

machine and clean both the front
panel and the inside compartments
with a soft sponge dampened with a
sanitising detergent solution. Dry with
a soft cloth to avoid scratching.

Water tank

It is preferable to empty the water
tank daily and refill it, when possible
just before preparing coffee, with cold
potable water. Wash the water tank
by hand using a sanitising detergent
solution.

Steam dispenser

Clean the steam dispenser with
a soft sponge using only water,
preferably hot water. To remove any
incrustations, we recommend washing
the components in the dishwasher.
The steam spout can be unscrewed
for washing in the dishwasher. When it
is used for frothing milk, it is advisable
to release some steam first to flush out
any remaining residues of milk or froth.

EN

23

10 Descaling the machine

When the message “DESCALING”
appears on the display with the
machine off, it is time to descale
your machine using specific
products that are appropriate for
coffee machines.

Attention - Very Important!
Do not use lemon-based products

for descaling. These products
contain citric acid, which in
contact with calcium at high
temperatures forms a chemical
reaction, creating calcium citrate
that could lead to the total
obstruction of the water circuits.

Proceed as follows:
Open the drawer and remove the

water from the tray and any coffee

grounds from the container. Re-close

the drawer without replacing the grille,
and position the steam nozzle so that
the water that comes out of it falls into
the tray.

• Switch on the machine and wait till

the words WATER and STEAM have

stopped flashing.

• Switch off the machine and go into

programming mode by pressing the
key until the displays shows

“PROGRAMMING”.

• Select the descaling function

using the keys

and

“DESCALING” appears on the
display panel.

• Press and hold the two keys

together and then press

• The machine prepares for

descaling. When you hear the
beep of confirmation, the message
DESCALING STAGE 01 appears
on the display.

DESCALING STAGE 01: Fill the tank
halfway full with the descaling product
then press button .

DESCALING STAGE 02: keep the
steam button pressed.

DESCALING STAGE 03: machine
starts to delivery water from nozzles.

DESCALING STAGE 04: refill water
tank with fresh water, Press button

.

DESCALING STAGE 05: machine
starts cleaning cicle.

Press the steam button, fill the tank
with water and wait until the coffee
and water temperatures are reached.

The manufacturer declines all
responsibility for any damage
caused by failure to carry out
descaling.

IMPORTANT: machine provided
with direct water supply mast be
plumbed according to regional
rules, with main tap, retaining
valve, 150micron filter.

EN

24

11 Trouble-shooting

The machine does not switch on.

• Front panel not completely closed.

• No electricity.

The coffee does not come out or
only comes out in slow drips.

• Lack of water in the tank.

• Coffee grind too fine.

• Coffee Machine pipes obstructed.

The coffee comes out too fast and
is not creamy.

• Coffee grind too coarse.

• Coffee too old.

• Coffee blend.

The milk froth does not form.

• Check that the flow of steam is

suitable.

Loud noise of the pump when
dispensing.

• Lack of water in the tank.

• Insufficient pressure in the filter holder

due to a coarse grind.

Auto-diagnostics

The electronic circuits manage
and recognize various alarms and
operating anomalies.

These are indicated as flashing on the
display panel

1. With the machine on:

Technical service

Solution: Before calling in the technical

service, try opening and re-closing the
machine.

2. With the machine on:

Water pressure

Solution: Check the water tank and
turn the switch on the left side off. Turn
the machine back on until the alarm
disappears.

3. With the machine on:

Grinder

Solution: Check for the presence of
foreign bodies in the grinder (stones,
impurities, other foreign bodies).

Turn the grind adjustment knob anti­clockwise (coarse grind) all the way.

Remove any impurities by running

the grinder for a few seconds. Then
re-adjust the grind to the previous
position.

For any other operating anomaly,
contact your nearest service
center.

EN

25

12 Technical Data

• External dimensions: H.458 x L.595 x

D.320 mm

• Flush-mount dimensions:
H.450 x L.568 x D.315 mm

• Operating voltage:
220-240 V~ 50/60Hz: 110V~60Hz

• Pump pressure: 15 bar

• Pump power: 48 W

• Coffee water heater power: 1000 W

• Steam water heater power: 600 W

• Grinder power: 100 W

• Max power: 1700/1100 W

• Water tank capacity: approx. 2.5 I

• Coffee tank capacity: approx. 350 g

• Coffee water heater heating time:

approx. 2 min.

• Gross weight: 32 kg

• Net weight: 28 kg

CE This appliance complies with
Directive 73/23

• regarding electrical safety

standards EN 60335-1 (ed. 2002

- Safety of household and similar
electrical appliances) and EN
60335-2-15 (ed. 2002 - Particular
requirements for appliances for
heating liquids).

• EMC 89/336 and the respective

standards:
55014-1
55014-2
61000-3-2
61000-3-3