Blodgett KLTF-40G User Manual

KLTF-G

Gas Fully Jacketed

Floor Model Tilting Kettle

OPTIONS AND ACCESSORIES

(AT ADDITIONAL CHARGE)

n Faucets
q Single pantry faucet with swing spout
q Double pantry faucet with swing spout
n Draw Off valves and accessories
q 2” (50mm) draw off valve
q 3” (76mm) draw off valve
q 3” (76mm) dairy valve
q Perforated strainer for draw off
q Solid stainless steel disc for draw off valve
n Etched markings
q Gallons
q Litres

q Spring assist hinged stainless steel cover
q Triple basket assembly
q Graduated measuring strip
q Strainer hook
q Pour strainer
q Correctional package
q 220VAC
q 316 stainless steel liner

KLTF-G FULLY JACKETED TILTING KETTLE

Project

Item No.

Quantity

q Model KLTF-40G - 40 gallon (151 litres) gas floor modeL tilting kettle

CONSTRUCTION

n 304 stainless steel construction
n Fully jacketed with factory sealed distilled water enclosure
n Hemispherical design on bottom of kettle for superior heat circulation
n Drip proof stainless steel console
n Legs fitted with four hole adjustable flanged feet for securing to floor
n Self-locking tilt mechanism with trunnions connected to the gear and

control consoles permit the kettle to tilt forward 90° for emptying

n Stainless steel control housing
n 304 stainless steel liner
n High efficiency power burner system

OPERATION

n Integrally mounted controls
n Power switch
n Pressure switch
n Direct immersion thermostat
n Water sight glass
n Cook indicator light
n Pressure gauge
n Low water light
n Low water shut off
n Pressure relief valve
n 165-275°F (74-135°C) temperature range

STANDARD FEATURES

n Manual control
n Stainless steel faucet bracket
n 120 VAC, 1 phase, 60 Hz
n One year parts and labor warranty*

* For all international markets, contact your local distributor.

BLODGETT

www.blodgett.com

44 Lakeside Avenue, Burlington, VT 05401 • Phone: [phone] • Fax: [phone]

KLTF-G FLOOR MODEL TILTING KETTLE

APPROVAL/STAMP

SHORT FORM SPECIFICATIONS

Provide Blodgett model KLTF-40G (40 gallon) gas fired tri-leg tilting kettle. The unit shall have a double wall interior to form a full steam jacket around the kettle. The jacket enclosure shall
contain distilled water which is factory sealed. The bottom of the kettle shall be of hemispherical design for superior heat circulation. The console shall be drip proof, stainless steel clad and
shall be mounted on 6” removable legs fitted with two hole adjustable flanged feet for securing to floor. The unit shall pivot on trunions connected to the tilt mechanism and the outboard
bearing connected to the gear and control consoles and shall permit the kettle to tilt forward a full 90° for complete emptying. The tilt mechanism shall be self locking for positive stop
action. Construction shall be of all welded satin finish 304 stainless steel. The controls shall be integrally mounted and shall include a power switch, direct immersion thermostat water site
glass with range of 165-275°F (74-135°C), a cook indicator light, pressure gauge, pressure relief valve, low water light and low water shut off. Unit shall be ASME code stamped and
National Board registered. Provide options and accessories as indicated.

MAXIMUM INPUT:

KLTF-40G 120,000 BTU

GAS SUPPLY:

3/4” IPS supply line required

Minimum Inlet Pressure:

POWER SUPPLY:

120VAC, 1 phase, 60 Hz., 2-wire w/ground

SHIPPING INFORMATION:

Approx. Weight:

KLTF-40G 1100 lbs. (499 kg)
Natural 6.0” W.C. static to unit
Propane 11.0” W.C. static to unit

NOTE: The company reserves the right to make substitutions of components without prior notice.

BLODGETT

www.blodgett.com

44 Lakeside Avenue, Burlington, VT 05401 • Phone: [phone] • Fax: [phone]

Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY

P/N S00099 Rev B (9/12)