Blodgett B12C-B Installation Manual

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain
this manual for the life of the equipment:

Model #: __________________________
Serial #: __________________________
Date Purchased: ___________________

Owner’s Manual

Heavy Duty Series Sectional Range

Charbroiler Models
Flush Open Burner Models
Graduated Hot-Top Models

Uniform Hot-Top Models

Standard Griddle Models

Step-Up Open-Burner Models

Thermostatic Griddle Models

Combination Open-Burner Hot-Top Models

Combination Open-Burner Griddle Models

Model B36A-BBB

Model B36A-TTT

Model B36A-BBB-SU

Model B36A-HHH

WARNING

Model B36A-CCC

Model B36A-GRAD

Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
Read installation, operation, and maintenance instructions thoroughly before installing or servicing this equipment.

1100 Old Honeycutt Road, Fuquay-Varina, NC 27526 USA • www.blodgettrange.com

MANUAL 1184743 REV 4 (10/08)
$21.00

HEAVY DUTY SERIES SECTIONAL RANGE

MANUAL SECTION SR

SAFETY PRECAUTIONS HEAVY DUTY SERIES SECTIONAL RANGE

SAFETY PRECAUTIONS

Before installing and operating this equipment, be sure everyone involved in its operation is fully trained and aware of
precautions. Accidents and problems can be caused by failure to follow fundamental rules and precautions.

The following symbols, found throughout this manual, alert you to potentially dangerous conditions to the operator,
service personnel, or to the equipment.

DANGER

WARNING

CAUTION

NOTICE

This symbol warns of immediate hazards that will result in severe injury or death.

This symbol refers to a potential hazard or unsafe practice that could result in injury or
death.

This symbol refers to a potential hazard or unsafe practice that could result in injury,
product damage, or property damage.

This symbol refers to information that needs special attention or must be fully understood,
even though not dangerous.

WARNING

FIRE HAZARD

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of cookin g appliances.
Keep area around cooking appliances free and clear of combustibles.
Purchaser of equipment must post in a prominent location detailed instructions to be followed in the event the

operator smells gas. Obtain the instructions from the local gas supplier.

WARNING

BURN HAZARD

Contact with hot surfaces will cause severe burns. Always use caution when operating cooking appliances.

WARNING

EXPLOSION AND ASPHYXIATION HAZARD

In the event a gas odor is detected, shut down equipment at the main gas shut-off valve and immediately call
the emergency phone number of your gas supplier.

Improper ventilation can result in headaches, drowsiness, nausea, and could result in death. Do not obstruct the
flow of combustion and ventilation air to and from cooking appliances.

WARNING

ELECTRIC SHOCK HAZARD

For appliances that use electric power, disconnect the power to the appliance before cleaning. Do not remove
panels that require tools to remove.

NOTICE

Blodgett Range appliances are intended for commercial use only. Not for household use.
Warranty will be void if service work is performed by other than a qualified technician, or if other than genuine

Blodgett Range replacement parts are installed.
Give this Owner’s Manual and important papers to the proper authority to retain for future reference.

Copyright © 2008 by Blodgett Range. All rights reserved. Published in the United States of America.

PAGE 2 OF 48 OWNER’S MANUAL 1184743 REV 4 (10/08)

HEAVY DUTY SERIES SECTIONAL RANGE INTRODUCTION

INTRODUCTION

Congratulations! You have purchased one of the finest pieces of heavy-duty commercial cooking equipment on the
market.

You will find that your new equipment, like all Blodgett Range equipment, has been designed and manufactured to
meet the toughest standards in the industry. Each piece of Blodgett Range equipment is carefully engineered and
designs are verified through laboratory tests and field installations. With proper care and field maintenance, you will
experience years of reliable, trouble-free operation. For best results, read this manual carefully.

RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This manual is for the Blodgett Range Heavy Duty Series Sectional Ranges
This manual does NOT cover Blodgett Range sectional fryers, fryer filter systems, salamander broilers, upright

broilers, cheese melters, or refrigerated bases. Those appliances have their own manuals.
The location of the serial plate depends on the type of base (see

serial plate is located on the backside of the kick-plate below the oven door (lift the kick-plate straight up and tilt the
top edge out and down.) On models with a cabinet base, the serial plate is located inside the left cabinet door. On
modular (countertop) models, the serial plate is located inside the front valve panel.

Read these instructions carefully before attempting installation. Installation and initial startup should be performed by
a qualified installer. Unless the installation instructions for this product are followed by a qualified service technician (a
person experienced in and knowledgeable with the installation of commercial gas and/or electric cooking equipment)
then the terms and conditions on the Manufacturer’s Limited Warranty will be rendered void and no warranty of any
kind shall apply.

In the event you have questions concerning the installation, use, care, or service of the product, write to:

Blodgett Range

1100 Old Honeycutt Road

Fuquay-Varina, North Carolina 27526 USA

Figure 1

Location of Serial Plate

Figure 1 below). On models with oven bases, the

Location of Serial Plate

OWNER’S MANUAL 1184743 REV 4 (10/08) PAGE 3 OF 48

SPECIFICATIONS HEAVY DUTY SERIES SECTIONAL RANGE

SPECIFICATIONS

NOTICE

Local codes regarding installation vary greatly from one area to another. The National Fire Protection Association,
Inc., states in its NFPA 96 latest edition that local codes are the “authority having jurisdiction” when it comes to
installation requirements for equipment. Therefore, installations should comply with all local codes.

Blodgett Range reserves the right to change specifications and product design without notice. Such revisions do
not entitle the buyer to corresponding changes, additions, or replacements for previously purchased equipment.

Blodgett Range appliances are intended for commercial use only, not for household use.
The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1, Natural Gas Installation Code, CAN/CGA-B149.1, or the Propane Installation Code CAN/CGA-
B149.2, as applicable, including:

1. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).

2. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.45
kPa).

CLEARANCES

WARNING

MINIMUM CLEARANCES FROM COMBUSTIBLE CONSTRUCTION

There must be adequate clearance between the sectional range and combustible construction. Clearance must
also be provided for servicing and for operation.

Open-Top

Standard-Burner

Models

Sides 10" 13" 10" 10" 6"

Back 6" 6" 12" 12" 6"

Floor* 0" 0" 0" 0" 0"

Do NOT install sectional charbroilers next to combustible materials.

* Models with 6" legs or casters are suitable for installation on combustible floors.
Adequate clearance must be provided in the aisle in front of the unit to permit operation (including opening of

doors and/or removal of grease drawers, drippings trays, and/or oven racks), as well as for servicing. No ad ditional
clearance is required for servicing as the sectional range is serviceable from the front.

Models with a convection-type oven require a minimum clearance of 2" between the motor on the back and non­combustible construction. Care must be taken to provide adequate air circulation to prevent the motor from
overheating.

Open-Top

45K-Burner

Models

Griddle
Models

Uniform Hot-Top

Models

Graduated

Hot-Top

Models

Minimum clearance from noncombustible construction is zero on the sides and back for all models (except for
models with a convection-type oven).

The high-temperature flue products flow out through the top of the flue riser of all models, and from the top of
open-top and charbroiler models. Installation under a vented hood is recommended.

Salamander broilers and cheese melters mounted on the flue riser of a sectional range may require additional
minimum clearances (see the documentation for those appliances).

PAGE 4 OF 48 OWNER’S MANUAL 1184743 REV 4 (10/08)

HEAVY DUTY SERIES SECTIONAL RANGE SPECIFICATIONS

VENTILATION

WARNING

Improper ventilation can result in personal injury or death. Ventilation which fails to properly remove flue products
can cause headaches, drowsiness, nausea, or could result in death.

All gas appliances must be installed in such a manner that the flow of combustion and ventilation air is not
obstructed. Provisions for adequate air supply must be provided. Do not obstruct the area under the control panel
or below the oven door (on the front), or the area below the flue riser (on the back) as combustion air enters
through these areas.

NOTICE

Proper ventilation is the owner’s responsibility. Any problem due to improper ventilation will not be covered by the
warranty.

Be sure to inspect and clean the ventilation system according to the ventilation equipment manufacturer’s
instructions.

Air for combustion enters from the front below the valve panel, as well as from the rear into the burner box. Ranges
with solid tops (griddles and hot-tops) vent their flue products up the flue riser. On units with a base oven, combustion
air enters from the front below the oven door. Oven flue products are vented up the flue riser.

Lack of sufficient ventilation will cause poor burner and pilot operating characteristics, resulting in inefficient
performance. Such conditions also cause high ambient temperatures at the manifold area and create valve and
thermostat problems.

If a ventilation canopy is used, it is recommended that the canopy extend 6" past the sectional range and that the
bottom edge be located 6'6" from the floor. Filters should be installed at an angle of 45° or more from the horizontal.
This position prevents dripping grease, and facilitates collecting the run-off grease in a drip pan under the filter.

A strong exhaust fan tends to create a vacuum in the room and may interfere with burner performance or may
extinguish pilot flames. Fresh air openings approximately equal to the fan area will relieve such a vacuum. The
exhaust fan should be installed at least 2" above the top of the flue riser.

If the sectional range is connected directly to an outside flue, a CSA design certified down draft diverter must be
installed.

In case of unsatisfactory performance by any gas appliance, check the appliance with the exhaust fan turned OFF. Do
this only long enough to check whether doing so corrects any problems with equipment performance. Then turn the
exhaust fan back on and let it run to remove any exhaust that may have accumulated during the test.

GAS SUPPLY

The sectional range is design-certified for operation on natural or propa ne gases. The sectional range is shipped
configured and adjusted for the type of gas specified by the purchaser, which is indicated on the serial plate (see
Figure 1 on page 3). Connect the sectional range ONLY to the type of gas for which it is configured and adjusted.

Each section has a 1-1/4" front gas manifold that can be coupled to adjacent section(s). Sections can be ordered with
an optional 1" rear gas connection with a male NPT connector. Minimum supply pressure is 7" W.C. for natural gas,
11" W.C. for propane. An external pressure regulator and shut off valve must be provided. If using a flexible-hose gas
connection, the I.D. of the hose must not be smaller than the connector on the unit and must comply with ANSI
Z21.69. Provide an adequate means of restraint to prevent undue strain on the gas connection.

If applicable, the vent line from the gas appliance pressure regulator shall be installed to the outdoors in accordance
with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1, Natural Gas
Installation Code, CAN/CGA-B149.1, or the Propane Installation Code CAN/CGA-B149.2, as applicable.

An adequate gas supply is imperative. Undersized or low pressure lines will restrict the volume of gas required for
satisfactory performance. Fluctuations of more than 25% on natural gas or 10% on propane gas will create problems
and affect burner operating characteristics. A 1/8" pressure tap is located on the manifold to measure the manifold
pressure. The supply line to the sectional range should be no smaller than the inside diameter of the pipe on the
sectional range to which it is connected.

OWNER’S MANUAL 1184743 REV 4 (10/08) PAGE 5 OF 48

SPECIFICATIONS HEAVY DUTY SERIES SECTIONAL RANGE

Figure 2

Dimensions

36" Flue Riser

12"

(305)

24"

(610)

7" (178)

2" (51)

33-3/4"

35-3/4"

(908)

(859)

Front Gas

Manifold

15-3/4"

(400)

2-1/2" (64)

SIDE VIEW

24" (610)

41-3/4" (1060)
38" (965)

35-3/4" (908)

32" (813)

Motor for

Convection

Oven Model

Flue riser for “deep” depth-option extends rearward 6"
(cooking suface area is same as for “standard” depth).

8-1/2" (216)

SIDE VIEW of MODULAR MODEL

38-3/4"

(984)

2" (51)

36" (914)

48" (1219)

24" Flue Riser

5" Flue Riser

36"

(914)

Optional

Rear Gas

Connection

6" (152)

41"

(1041)

20"

(508)

60"

(1524)

72"

(1829)

7" (178)

7" (178)

2-1/2" (64)

Electrical

Connection

for Oven

Models

18"

(457)

7" (178)

2-1/2" (64)

PAGE 6 OF 48 OWNER’S MANUAL 1184743 REV 4 (10/08)

HEAVY DUTY SERIES SECTIONAL RANGE SPECIFICATIONS

UTILITY REQUIREMENTS AND CRATED WEIGHT

Model Width Base Type Top Type

B12C-B 12" cabinet flush 35K open-burner 70,000 60,000 - - 225 (102)
B12C-G 12" cabinet standard griddle 32,000 28,000 - - 225 (102)
B12C-H 12" cabinet uniform hot top 32,000 28,000 - - 180 (82)
B12N-B 12" modular flush 35K open-burner 70,000 60,000 - - 175 (79)
B12N-G 12" modular standard griddle 32,000 28,000 - - 175 (79)
B12N-H 12" modular uniform hot top 32,000 28,000 - - 130 (59)
B24C-BB 24" cabinet flush 35K open-burner 140,000 120,000 - - 480 (218)
B24C-BB-SU 24" cabinet step-up 35K open-burner 140,000 120,000 - - 480 (218)
B24C-CC 24" cabinet charbroiler 64,000 56,000 - - 360 (163)
B24C-GG 24" cabinet standard griddle 64,000 56,000 - - 300 (136)
B24C-HH 24" cabinet uniform hot top 64,000 56,000 - - 280 (127)
B24C-TT 24" cabinet thermostatic griddle 64,000 56,000 - - 300 (136)
B24N-BB 24" modular flush 35K open-burner 140,000 120,000 - - 395 (179)
B24N-BB-SU 24" modular step-up 35K open-burner 140,000 120,000 - - 395 (179)
B24N-CC 24" modular charbroiler 64,000 56,000 - - 360 (163)
B24N-GG 24" modular standard griddle 64,000 56,000 - - 300 (136)
B24N-HH 24" modular uniform hot top 64,000 56,000 - - 205 (93)
B24N-TT 24" modular thermostatic griddle 64,000 56,000 - - 300 (136)
B36A-BBB 36" convection oven flush 35K open-burner 255,000 222,000 3.8 1.6 740 (336)
B36A-BBB-SU 36" convection oven step-up 35K open-burner 255,000 222,000 3.8 1.6 740 (336)
B36A-CCC 36" convection oven charbroiler 141,000 126,000 3.8 1.6 775 (352)
B36A-GGG 36" convection oven standard griddle 141,000 126,000 3.8 1.6 840 (381)
B36A-GRAD 36" convection oven graduated hot-top 107,000 87,000 3.8 1.6 760 (345)
B36A-HHH 36" convection oven uniform hot top 141,000 126,000 3.8 1.6 720 (327)
B36A-TTT 36" convection oven thermostatic griddle 141,000 126,000 3.8 1.6 840 (381)
B36A-XX 36" convection oven flush 45K open-burner 225,000 222,000 3.8 1.6 740 (336)
B36C-BBB 36" cabinet flush 35K open-burner 210,000 180,000 - - 490 (222)
B36C-BBB-SU 36" cabinet step-up 35K open-burner 210,000 180,000 - - 490 (222)
B36C-CCC 36" cabinet charbroiler 96,000 84,000 - - 620 (281)
B36C-GGG 36" cabinet standard griddle 96,000 84,000 - - 590 (268)
B36C-GRAD 36" cabinet graduated hot-top 62,000 45,000 - - 510 (231)
B36C-HHH 36" cabinet uniform hot top 96,000 84,000 - - 470 (213)
B36C-TTT 36" cabinet thermostatic griddle 96,000 84,000 - - 590 (268)
B36C-XX 36" cabinet flush 45K open-burner 180,000 177,000 - - 490 (222)
B36D-BBB 36" standard oven flush 35K open-burner 255,000 222,000 0* 0* 690 (313)
B36D-BBB-SU 36" standard oven step-up 35K open-burner 255,000 222,000 0* 0* 690 (313)
B36D-CCC 36" standard oven charbroiler 141,000 126,000 0* 0* 750 (340)
B36D-GGG 36" standard oven standard griddle 141,000 126,000 0* 0* 790 (358)
B36D-GRAD 36" standard oven graduated hot-top 107,000 87,000 0* 0* 710 (322)
B36D-HHH 36" standard oven uniform hot top 141,000 126,000 0* 0* 670 (304)
B36D-TTT 36" standard oven thermostatic griddle 141,000 126,000 0* 0* 790 (358)
B36D-XX 36" standard oven flush 45K open-burner 225,000 222,000 0* 0* 690 (313)
B36N-BBB 36" modular flush 35K open-burner 210,000 180,000 - - 450 (204)
B36N-BBB-SU 36" modular step-up 35K open-burner 210,000 180,000 - - 450 (204)
B36N-CCC 36" modular charbroiler 96,000 84,000 - - 350 (159)
B36N-GGG 36" modular standard griddle 96,000 84,000 - - 530 (240)
B36N-GRAD 36" modular graduated hot-top 62,000 45,000 - - 450 (204)
B36N-HHH 36" modular uniform hot top 96,000 84,000 - - 410 186)
B36N-TTT 36" modular thermostatic griddle 96,000 84,000 - - 530 (240)
B36N-XX 36" modular flush 45K open-burner 180,000 177,000 - - 450 (204)
B48A-CCCC 48" convection oven charbroiler 173,000 154,000 3.8 1.6 621(281)
B48A-GGGG 48" convection oven standard griddle 173,000 154,000 3.8 1.6 729 (330)
B48A-TTTT 48" convection oven thermostatic griddle 173,000 154,000 3.8 1.6 729 (330)
B48C-CCCC 48" cabinet charbroiler 128,000 112,000 - - 462 (209)
B48C-GGGG 48" cabinet standard griddle 128,000 112,000 - - 480 (217)
B48C-TTTT 48" cabinet thermostatic griddle 128,000 112,000 - - 480 (217)
B48D-CCCC 48" standard oven charbroiler 173,000 154,000 0* 0* 568 (257)
B48D-GGGG 48" standard oven standard griddle 173,000 154,000 0* 0* 676 (306)
B48D-TTTT 48" standard oven thermostatic griddle 173,000 154,000 0* 0* 676 (306)
B48N-CCCC 48" modular charbroiler 128,000 112,000 - - 276 (125)
B48N-GGGG 48" modular standard griddle 128,000 112,000 - - 395 (179)
B48N-TTTT 48" modular thermostatic griddle 128,000 112,000 - - 395 (179)

Natural Gas

(BTU/hour)

GAS ELECTRICITY

Propane

(BTU/hour)

120V

(amps)

208/240V

(amps)

* Standing Oven Pilot Models

Crated Weight

pounds (kg)

OWNER’S MANUAL 1184743 REV 4 (10/08) PAGE 7 OF 48

SPECIFICATIONS HEAVY DUTY SERIES SECTIONAL RANGE

ELECTRICITY SUPPLY

Units with convection-oven bases with optional electronic ignition require electric po wer (50Hz or 60Hz single-phase
AC). 120V models have a 7-foot (2134 mm) power cord with a grounded plug (1.0 amps for “D” Models and 4.8 amps
for “A” Models). The 208/240V models have a terminal block for connection to a single-phase 208/24 0V source (1.0
amps for “D” Models and 2.6 amps for the “A” Models).

The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as
applicable. An electrical diagram is located on the rear of the range, near the motor.

PAGE 8 OF 48 OWNER’S MANUAL 1184743 REV 4 (10/08)

HEAVY DUTY SERIES SECTIONAL RANGE OPERATION

OPERATION

DANGER

EXPLOSION HAZARD

In the event a gas odor is detected, shut down equipment at the main shut off valve. Immediately call the
emergency phone number of your gas supplier.

CAUTION

If a pilot flame pilot should go out, the flow of gas to the corresponding burner is NOT interrupted. Consequently, it
is the responsibility of the operator to check the ignition of each burner immediately EVERY TIME a burner is
turned on. Should ignition fail after 10 seconds, turn off the burner, wait 5 minutes, and then try again.

LIGHTING AFTER GAS HAS BEEN SHUT OFF

When turning on the main gas supply to a sectional range, do the following:

1. Make sure that all the control knobs and power switches of all the connected appliances are in the OFF position.

2. Turn on the gas-supply shut-off valve(s).

3. Light the standing pilots of each connected appliance.

4. Light the ovens of the sectional range first, then wait six minutes before turning on the top sections. This enables
all air to be purged from the sectional-range gas piping.

SHUTDOWN OF ENTIRE RANGE

To place the range in a standby state (ready for use), Oven bases with the electronic ignition option, turn all burner
control knobs to OFF, set all thermostats to their lowest position, and switch all ovens OFF. The pilots will remain lit.
On the standing pilot units, same as above except turn thermostat knob to the “OFF” position. The pilots will remain
lit.

To completely shut down the range for an extended period (or prior to disconnecting the gas supply), place the range
in a standby state (as described in the previous paragraph), then turn OFF the manual shut -off valves of all gas
supply connections. This will extinguish the pilots.

OWNER’S MANUAL 1184743 REV 4 (10/08) PAGE 9 OF 48

OPERATION HEAVY DUTY SERIES SECTIONAL RANGE

Figure 3

Operation of Open-Burner Sections

Each 12"-wide section has two control knobs. The left knob
controls the rear burner, while the right knob controls the
front burner. Each knob can be turned to OFF or to any
position in the range from LOW to HIGH.

To start cooking, turn the appropriate control knob to HIGH.
Visually check that the burner ignites. The gas does NOT
automatically shut off if the burner does not ignite! If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

While cooking, do not allow excessive drippings and/or
debris to accumulate on or below the burners. When
necessary, pull out and clean the drippings tray.

Burner Grate

(lifts out for cleaning)

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each burner has a pilot located beside the burner. To light a
pilot, do the following:

1. Check that the burner control knob is in the OFF position.

2. Check that the pilot is in the correct position beside the
burner.

3. Turn on the gas supply to the sectional range (if not
already on).

4. Light the pilot with a match or a pilot-lighting device. The
pilot flame should be blue and steady.

Base-Oven Gas

Rear-Burner

Control Knob

(OFF, HIGH-to-LOW)

PAGE 10 OF 48 OWNER’S MANUAL 1184743 REV 4 (10/08)

Front-Burner

Control Knob

(OFF, HIGH-to-LOW)

Drippings Tray

(slides out for cleaning)

Shut-Off Valve
(has no effect on
range-top burners)

HEAVY DUTY SERIES SECTIONAL RANGE OPERATION

Figure 4

Operation of Uniform Hot-Top Section

Each 12”-wide section has one control knob, which can be
turned to OFF or to any position in the range from LOW to
HIGH. When the control is set to HIGH, the hot top surface
will heat to about 700°F (370°C).

To start cooking, turn the appropriate control knob to HIGH.
Visually check that the burner ignites. The gas does NOT
automatically shut off if the burner does not ignite! If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Do not waste gas and abuse equipment by leaving the
burner on HIGH all the time. Damage to the plates and
certain electronic components may occur, and MAY VOID
YOUR WARRANTY. During idle periods, turn the control to
LOW to keep the top warm.

Uniform Hot Top Plate

(lifts out for cleaning

and lighting pilot)

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each 12”-wide section has two burners, each of which has a
pilot located near the front of the burner. To light the pilots,
do the following:

1. Check that the control knob is in the OFF position.

2. Lift up a hot-top section plate in order to expose the two
pilots.

3. Check that each pilot is in the correct position.

4. Turn on the gas supply to the sectional range (if not
already on).

5. Light the pilots with a match or a pilot-lighting device. The
pilot flames should be blue and steady.

Base-Oven Gas
Shut-Off Valve

Burner Control Knob

(OFF, HIGH-to-LOW)

OWNER’S MANUAL 1184743 REV 4 (10/08) PAGE 11 OF 48

(has no effect

on hot-top)

OPERATION HEAVY DUTY SERIES SECTIONAL RANGE

Figure 5

Operation of Graduated Hot-Top Section

Each section has one control knob, which can be turned to
OFF or to any position in the range from LOW to HIGH.
When the control is set to HIGH, the round center section will
heat to about 725°F (385°C), the ring-shaped section will
heat to about 625°F (330°C), and the outer areas will heat to
about 500°F (260°C).

To start cooking, turn the control knob to HIGH. Visually
check that the burner ignites. The gas does NOT
automatically shut off if the burner does not ignite! If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Do not waste gas and abuse equipment by leaving the
burner on HIGH all the time. Damage to the plates and
certain electronic components may occur, and MAY VOID
YOUR WARRANTY. During idle periods, turn the control to
LOW to keep the top warm.

When done cooking, turn the control knob to OFF. (The pilot
should remain lit).

Each section has one burner. The pilot is located adjacent to
the burner. To light the pilot, do the following:

1. Check that the control knob is in the OFF position.

2. Lift out the round center plate in order to expose the pilot.

3. Check that the pilot is in the correct position.

4. Turn on the gas supply to the sectional range (if not
already on).

5. Light the pilot with a match or a pilot-lighting device. The
pilot flame should be blue and steady.

Lower Temperature Area

(plate lifts out for cleaning)

Medium Temperature Area

(plate lifts out for cleaning)

Burner Control Knob

(OFF, HIGH-to-LOW)

HighTemperature Area

(plate lifts out for cleaning

and lighting pilot)

Lower Temperature Area

(plate lifts out for cleaning)

Base-Oven Gas
Shut-Off Valve
(has no effect

on hot-top)

PAGE 12 OF 48 OWNER’S MANUAL 1184743 REV 4 (10/08)

HEAVY DUTY SERIES SECTIONAL RANGE OPERATION

Figure 6

Operation of Charbroiler Section

Each 12”-wide section has one control knob, which can be
turned to OFF, HIGH, or LOW. Each burner top-grate can be
turned over to provide either wide branding marks or
narrower branding marks with channels to carry away
drippings (and so reduce flare up). The back-to-front slope of
each top-grate is adjusted by positioning the back end of the
top-grate on either the lower or the higher grate-support rail.
The radiants (just above the burners) can be reversed front­and-back to provide higher heat toward the back than the
front, or vice versa. “Lava rock” briquettes can be placed on
grates located above the radiants.

To start cooking, turn the appropriate control knob to HIGH.
Visually check that the burner ignites. The gas does NOT
automatically shut off if the burner does not ignite! If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Grates

(lift out for cleaning)

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each 12”-wide section has two burners, each of which has a
pilot located near the front of the burner. To light the pilots,
do the following:

1. Check that the burner control knob is in the OFF position.

2. Lift up a grate in order to expose the two pilots. They are
accessible through a slot near the front end of the radiant
plate.

3. Check that each pilot is in the correct position.

4. Turn on the gas supply to the sectional range (if not
already on).

5. Light the pilots with a match or a pilot-lighting device. The
pilot flames should be blue and steady.

Base-Oven Gas
Shut-Off Valve

Burner Control Knob

(OFF, HIGH, or LOW)

OWNER’S MANUAL 1184743 REV 4 (10/08) PAGE 13 OF 48

Drippings Tray

(slides out for cleaning)

(has no effect
on charbroiler)

OPERATION HEAVY DUTY SERIES SECTIONAL RANGE

Figure 7

Operation of Standard (Non-Thermostatic) Griddle Sections

Each 12”-wide section has one control knob, which can be
turned to OFF, HIGH, or LOW.

To start cooking, turn the appropriate control knob to HIGH.
Check that the burner ignites. The gas does NOT
automatically shut off if the burner does not ignite! If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Always remember to heat the griddle slowly because quick
heating may cause costly damage. Never place utensils on
the griddle.

Do not waste gas and abuse equipment by leaving the
griddle on HIGH all the time. Damage to the griddle and
certain electronic components may occur, and MAY VOID
YOUR WARRANTY. During idle periods, turn the control to
LOW to keep the griddle warm. (Do not allow the griddle to

overheat above 550°F (288°C), as this will cause warping or
breakage.)

When necessary while cooking, pull out and empty the
grease drawer.

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each griddle section has a single pilot that is lit using a long
match inserted thorough a hole in the front valve panel. (A
48"-wide griddle has two pilots.) To light the pilot, do the
following:

1. Check that all the control knobs are in the OFF position.

2. Turn on the gas supply to the sectional range (if not
already on).

3. Light the pilot by inserting a long match (at least 11" long)
or pilot-lighting device straight into the hole on the front
valve panel of the griddle.

Base-Oven Gas
Shut-Off Valve

Burner Control Knob

(OFF, HIGH, or LOW)

PAGE 14 OF 48 OWNER’S MANUAL 1184743 REV 4 (10/08)

Grease Drawer

(slides out for cleaning)

Pilot-Lighting

Opening

(has no effect

on griddle)

HEAVY DUTY SERIES SECTIONAL RANGE OPERATION

Figure 8

Operation of Thermostatic Griddle Sections

Each 12”-wide section has one control knob that can be
turned to OFF, or to any temperature in the range 150°F to
400°F (66°C to 204°C).

To start cooking, turn on the appropriate control knob. Check
that the burner ignites. If the burner does not ignite, check
and/or light the pilots (see procedure at right).

Never place utensils on the griddle.

Do not waste gas and abuse equipment by leaving the
griddle set at a high temperature all the time. Damage to

the griddle and certain electronic components may occur,
and MAY VOID YOUR WARRANTY. During idle periods,
turn the control to a low temperature to keep the griddle
warm. (Do not allow the griddle to overheat above 550°F
(288°C), as this will cause warping or breakage.)

When necessary while cooking, pull out and empty the
grease drawer.

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each griddle section has a single pilot that is lit using a long
match inserted thorough a hole in the front valve panel. (A
48"-wide griddle has two pilots.) To light the pilot, do the
following:

1. Check that all control knobs are in the OFF position.

2. Turn on the gas supply to the sectional range (if not
already on).

3. Turn on the Griddle Gas Shut-Off Valve (if not already
on).

4. Press and hold in the Safety Switch Button.

5. Light the pilot by inserting a long match (at least 11" long)
or pilot-lighting device straight into the hole on the front
valve panel of the griddle.

6. After about a minute, release the Safety Switch Button.
The pilot should remain lit.

Safety
Switch
Button

Base-Oven Gas
Shut-Off Valve

Burner Control Knob

(OFF, temperature)

OWNER’S MANUAL 1184743 REV 4 (10/08) PAGE 15 OF 48

Griddle Gas

Shut-Off Valve

Grease Drawer

(slides out for cleaning)

Pilot-Lighting

Opening

(has no effect

on griddle)