Blodgett 6G-6K-SB User Manual
Project
Item No.
Quantity
Model 6G-6K-SB(36) (two 3 pan convection steamer compartments with
one 6 gallon kettle on a 36” wide, 200,000 BTU boiler)
CONSTRUCTION
Stainless steel construction
Stainless steel steamer doors with strong continuous hinge and are field
reversible for left or right swing. Insulated doors have a one piece,
replaceable seal. Hidden magnetic door switch cuts power to blower and
steam flow to that cavity, when the door is opened
Steamer pan support racks are polished stainless steel and removable
for easy cleaning
Wide drip sink with condensate drain is positioned under cavity doors
Kettle has reinforced rim and butterfly shaped pouring lip.
Kettle support legs are heavy tubular stainless steel.
Kettle shall be coded and registered for operation up to 55 PSI.
Gas heated, 36” wide cabinet base shall have stainless steel frame with
all stainless steel top deck, hinged front access panel and removable
side and rear panels
Cabinet-mounted boiler is ASME Code-constructed and National Board
registered for operation up to 15 PSI.
Front and rear legs shall have adjustable bullet feet
OPERATION
Steamer cavity controls are mounted on the front panel for easy access
with separate ON-OFF/60 minute timer control with constant steam setting, for each steamer cavity.
Kettle steam control valve and HOT/COLD water faucet handles are front
mounted with boiler controls.
Gas boiler has a gas control valve, power-ON switch, RESET light, start
switch, low water sensor, pop safety valve, water level sight glass and
outside cabinet mounted pressure gauge.
Unit will shut off if water level is low or unit builds too much pressure
When power switch is turned “off”, the boiler automatically drains to
reduce sediment build-up, after the water has cooled to 170°F.
Each steamer cavity shall have a powerful side mounted blower, which
increases steam velocity and provides efficient steam distribution
throughout cavity and between loaded pans.
Twin gas-heated, cabinet-mounted pressure boiler to provide atmospher-
ic steam to each chamber at a temperature of approximately 212º (F)
and steam to kettle at approximately 10 PSI.
The 200,000 BTU generator delivers 3.7 boiler horsepower.
Electronic ignition
STANDARD FEATURES
1/2” NPT power take-off valve for powering adjacent equipment
Flush mounted pouring sink with splash shield
Unit shall be provided with hot and cold water faucet with swing spout
One year parts and labor warranty*
* For all international markets, contact your local distributor.
BLODGETT
44 Lakeside Avenue, Burlington, VT 05401
Toll Free: (800) 331-5842 • Phone: (802) 860-3700 • Fax: (802) 864-0183
OPTIONS AND ACCESSORIES
(AT ADDITIONAL CHARGE)
Flange mounting feet
Independent cold water to condensate spray
Cover and-or basket insert for kettle
6G-6K-SB(36)
Convection Steamer with Kettle
on a Gas Boiler Base
6G-5K-SB STEAMER WITH KETTLE ON A GAS BOILER BASE
Pan Size Per Cavity Total
12” x 20” x 1” 6 12
12” x 20” x 2.5” 3 6
12” x 20” x 4” 2 4
CAPACITY
BLODGETT
www.blodgett.com • 44 Lakeside Avenue, Burlington, VT 05401 • Phone: (802) 658-6600 • Fax: (802) 864-0183
6G-6K-SB(36)
SHORT FORM SPECIFICATIONS
Provide Blodgett model 6G-6K-SB (6 pan steamer and 6 gallon direct steam kettle on a 36” wide, 200,000 BTU gas boiler base base. All stainless steel construction with two independent steamer chambers, each with powerful blower to circulate steam within cavity and individual 60 minute timer with constant steam setting. Steamer doors are insulated, field reversible,
with easy open latch and hidden magnetic door switch. Drip sink with condensate drain is provided under cavity doors. Three (21/2” deep) pan capacity per chamber. Cabinet base has
stainless steel frame, all stainless steel exterior, with removable front access doors and adjustable bullet feet. Pouring sink and HOT/COLD water faucet provided for kettle. Boiler ASME
code constructed for 15 PSI maximum with 200,000 BTU firing rate, 120,000 BTU output and 3.7 boiler horsepower. Power take-off to divert steam to adjacent equipment is standard.
Provide options and accessories as indicated.
Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY
NOTE: The company reserves the right to make substitutions of
components without prior notice.
TOP VIEW
2
4
6
3
7
5
5
1
7.56 (192)
21.25 (540)
18.5 (470)
14.38
(365)
3 (76)
2.5
(64)
30.63
(778)
Condensate
drain vent
Flue
Clearance
6 (152)
20.38
(518)
18.06 (459)
Sink
drain
Treated
water supply
connection
Un-treated
water supply
connection
(optional)
DETAIL VIEW
of water connection
(if second connection ordered)
RESET
ONREADY
55
50
45
40
35
30
25
20
15
10
5
ON
OFF
TIMED
TIMED
OFF
ON
5
10
15
20
25
30
35
40
45
50
55
FRONT VIEW
4 (102)
Clearance
2” (51)
26.56
(675)
1.5 (38) min.
5.63 (67 max.
57.19
(1453)
4.63 (117)
36.13 (918)
4 (102)
Clearance
4” (102)
2
3
4
7
6
SIDE VIEW
34.19 (868)
2 (51)
1
3.88 (98)
23.06
(586)
24.31
(618)
Adjustable
bullet feet
6.25
(159)
5
NOTES:
1. Drain connection 1.25” (31) NPT (includes automatic & manual boiler, steamers,
condensate spray, kettle & sink)
2. Cold water supply 0.5 (31) NPT (for boiler, condensate spray & faucet)
3. Option: separate condensate spray 3/8” (9) NPT
4. Hot water supply 3/8” (9) NPT for faucet
5. Electrical connection 7/8” (22) dia hole (ref ½”(13) conduit knock out)
6. Gas connection 1/2” (13) NPT
7. Steam power take-off 1/2” (13) NPT
8. Dimensions are in inches (mm)
”
APPROVAL/STAMP
P/N S00132 Rev A (4/11)
WATER SUPPLY:
Water quality is a major factor affecting the performance of your steamer. If you
are unsure of water quality, consult a local water treatment specialist and have
the water analyzed. Your water supply must be within these general guidelines:
Total dissolved solids: Less than 30 PPM Total alkalinity: Less than 20 PPM
Silica: Less than 13 PPM Chlorine: Less than 1.5 PPM
pH Factor: 7.0 - 9.0
Water which fails to meet these standards should be treated by installation of a
water conditioner. Failure or malfunction of this steamer due to poor water quality is not covered under warranty.
WATER & DRAIN CONNECTIONS:
Drain 1 1/4” NPT free venting drain
Cold Water 1/2” NPT cold water supply line
Hot Water 3/8” NPT hot water supply line for faucet
Appliance is to be installed with backflow protection in accordance with Federal,
State or Local codes.
MAXIMUM INPUT:
6G-6K-SB(36) 200,000 BTU/hr
GAS SUPPLY:
1/2” NPT pipe or approved equivalent.
Minimum Inlet Pressure:
Natural 3.5" W.C. static to unit
Propane 10.0" W.C. static to unit
POWER SUPPLY:
115 volt, single phase, 60 cycle 15 AMP electric service, 4
AMP maximum load
SHIPPING INFORMATION:
Approx. Weight:
6G-6K-SB(36) 805 lbs. (366 kg)
Loading...