Blizzard Lighting Wink User Manual

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

Wink™ LED Moving Head 1

1. Getting Started 3

What’s In The Box? 3 Getting It Out Of The Box 3 Powering Up! 3 Getting A Hold Of Us 3 Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet Wink™ 5

Main Features 5 DMX Quick Reference 5 The Wink™ Pin-up Picture 6

3. Setup 7

Fuse Replacement 7 Connecting A Bunch Of Wink™ Fixtures 7 Data/DMX Cables 7 Cable Connectors 8 3-Pin??? 5-Pin??? Huh? 8 Take It To The Next Level: Setting up DMX Control 8 Installation 9

4. Operating Adjustments 10

The Control Panel 10 Control Panel Menu Structure 11 Set the Starting DMX Address 12 Select the DMX Channel Mode 12 DMX Mode 12 Slave Mode 12 Auto Mode 12 Sound Active Mode 12 Static Mode 12 Display Timeout 13 Display Invert 13 Pan/Tilt Invert 13 Calibration Settings 13 Fixture Test 13 Motor/Factory Reset 13 Runtime Info 13 Software 13 DMX Values In-Depth 14

5. Appendix 16

A Quick DMX Lesson 16 Keeping Your Wink™ As Good As New 17 Returns (Gasp!) 17 Shipping Issues 17 Tech Specs 18 Troubleshooting 18 Dimensional Drawings 19 Photometric Data 19

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x Wink™ LED Moving Head Fixture

• 1 x Ever-So-Handy Power Cord

• 1 x Mounting Bracket

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on your purchase of Wink™, your new eye of the storm LED moving head

xture! Now that you’ve got your Wink™ (or hopefully Winks)

, you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition. If anything looks as if it has been damaged in transit, notify the shipper immediately and keep the packing material for inspection. Again, please save the carton and all packing

materials. If a xture must be returned to the factory, it is important that the xture be

returned in the original factory box and packing.

Powering Up!

All xtures must be powered directly o a switched circuit and cannot be run o a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch.

AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the xture you receive is suitable for your local power supply. See the label on the xture or refer to the xture’s specications chart for more information. A xture’s listed current rating is its average current draw under normal conditions. Check the xture or device

carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch. All xtures must

be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, please just visit our website at www.blizzardlighting.com/ support and open a support ticket. We’ll be happy to help, honest.

Disclaimer: The information and specications contained in this document are subject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time. You can download the latest version of this document from www. blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Thomas 10/6/2017 J. Thomas 11/9/2017

Page 4

Please read these instructions carefully. They include

important information about the installation, usage and

maintenance of this product.

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the de-

cal or rear panel of the xture.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately. NEVER try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please open a support ticket at www. blizzardlighting.com/support.

Page 5

2. MEET WINK™

MAIN FEATURES

• 1* 60W RGBW high power 4-in-1 LED

• 4-segment RGB colored ring with 8* 0.5W RGB 3-in-1 LEDs

• Individual pixel and LED ring control

• 5-45 degree zoomable beam angle

• Blazing fast 540°/270° + innite pan/tilt

• Built-in auto and sound active programs

• Multiple static color presets and virtual color wheel

• Variable electronic dimming & strobe eects (1-20Hz)

• Flicker-free constant-current LED driver

• 3-pin male input and 3-pin female output

• PowerCON™ compatible AC power In/Out connectors

• Protocol: USITT DMX-512

• 19/26/35-channel DMX modes

• 2.4 inch TFT color LCD display panel with 4x touch sensitive buttons

DMX Quick Reference (19/26/35-Channel Modes)

CH. Basic (19ch) CH. Standard (26ch) CH. Extended (35ch)

1 Pan (0-540°) 1 Pan (0-540°) 1 Pan (0-540°) 2 Tilt (0-270°) 2 Fine Pan (16-bit) 2 Fine Pan (16-bit) 3 Pan & Tilt Speed 3 Tilt (0-270°) 3 Tilt (0-270°) 4 Innite Pan 4 Fine Tilt (16-bit) 4 Fine Tilt (16-bit) 5 Innite Tilt 5 Pan & Tilt Speed 5 Pan & Tilt Speed 6 Zoom (45-5°) 6 Innite Pan 6 Innite Pan 7 Zoom Speed 7 Innite Tilt 7 Innite Tilt 8 Red (0-100%) 8 Zoom (45-5°) 8 Zoom (45-5°) 9 Green (0-100%) 9 Zoom Speed 9 Zoom Speed 10 Blue (0-100%) 10 Red (0-100%) 10 Red (0-100%) 11 White (0-100%) 11 Green (0-100%) 11 Green (0-100%) 12 Strobe 12 Blue (0-100%) 12 Blue (0-100%) 13 Dimmer 13 White (0-100%) 13 White (0-100%) 14 Virtual Color Wheel 14 Strobe 14 Strobe 15 Color Presets 15 Dimmer 15 Dimmer 16 Color Presets Dimmer 16 Virtual Color Wheel 16 Virtual Color Wheel 17 Reset 17 Color Presets 17 Color Presets 18 Ring Macros 18 Color Presets Dimmer 18 Color Presets Dimmer 19 Ring Macro Speed 19 Reset 19 Reset

-- -- 20 Ring Red (0-100%) 20 Ring LED 1 - Red

-- -- 21 Ring Green (0-100%) 21 Ring LED 1 - Green

-- -- 22 Ring Blue (0-100%) 22 Ring LED 1 - Blue

-- -- 23 Ring Strobe 23 Ring LED 2 - Red

-- -- 24 Ring Dimmer 24 Ring LED 2 - Green

-- -- 25 Ring Macro 25 Ring LED 2 - Blue

-- -- 26 Ring Macro Speed 26 Ring LED 3 - Red

-- -- -- -- 27 Ring LED 3 - Green

-- -- -- -- 28 Ring LED 3 - Blue

-- -- -- -- 29 Ring LED 4 - Red

-- -- -- -- 30 Ring LED 4 - Green

-- -- -- -- 31 Ring LED 4 - Blue

-- -- -- -- 32 Ring Strobe

-- -- -- -- 33 Ring Dimmer

-- -- -- -- 34 Ring Macros

-- -- -- -- 35 Ring Macro Speed

Page 6

Figure 1: Wink™ Pin-Up Picture

1* 60W

RGBW

4-in-1 LED

with 5-45

Degree

Zoom

Figure 2: The Rear Connections

3-Pin

DMX In

4-Button

Control

Panel

with 2.4"

TFT Color

Display

3-Pin

DMX Out

Power

Output

Power

Input

4-Segment

LED Ring

with 8* 0.5W

RGB 3-in-1

LEDs

*Ring sec-

tions 1-4 run clockwise with "LED 1" at the

bottom position

if upright, or

the top position

if mounted

upside down.

Head/Arms

Blizzard Lighting Wink User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual