Blizzard Lighting Verismo IP Profile WW User guide

Download

Page 1

Blizzard Lighting, LLC

http://www.blizzardpro.com

Page 2

TABLE OF CONTENTS

1. Getting Started 3

What’s In The Box? 3 Getting It Out Of the Box 3 Powering Up! 3 Getting A Hold Of Us 3 Safety Instructions 4

2. Meet the Verismo™ Prole IP WW 5

Main Features 5

DMX Quick Reference 5 Verismo™ Prole IP WW Pin-Up Picture 6 The Rear Connections 6

3. Setup 7

Fuse Replacement 7 Connecting A Bunch of Verismo™ Prole IP Fixtures 7 Data/DMX Cabling 7

Cable Connectors 8

Take It To The Next Level: Setting Up DMX Control 8

Lens Barrels & Focusing 8 Insert the Gobo Holder 9

Rotating the Shutter Barrel 9 Mounting & Rigging 9

4. Operating Adjustments 10

The Control Panel 10 Control Panel Menu Structure 11 Static Mode 12

Dimming Curves 12

Dimming Speed 12 Dimming Frequency 13 DMX Fail 13 Fan Settings 13

System Reset 13 DMX Values In-Depth 13

5. Appendix 14

Keeping Your Verismo™ Prole IP As Good As New 14 Returns (Gasp!) 14

Shipping Issues 14 Tech Specs! 15

Page 2

Page 3

1. GETTING STARTED

What’s In The Box?

• Verismo™ Prole IP WW Engine

• Power Cable

• Gobo Holder

• This Lovely User Manual

Optional Accessories (sold separately)

The following accessories are available for this xture. But the lone wolves that

they are, they must be purchased separately. Contact your authorized Blizzard Lighting dealer for pricing.

• Verismo-LENS-19: Verismo Prole 19° Lens

• Verismo-LENS-26: Verismo Prole 26° Lens

• Verismo-LENS-36: Verismo Prole 36° Lens

• Verismo-LENS-50: Verismo Prole 50° Lens

Getting It Out Of the Box

Congratulations on purchasing the Verismo™ Prole IP WW. Now that you’ve got your xture, you should carefully unpack the box and check the contents

to ensure that all parts are present and in good condition. If anything looks as if it has been damaged in transit, notify the shipper immediately and keep the

packing material for inspection. Again, please save the carton and all packing materials. If a xture must be returned to the factory, it is important that the xture be returned in the original factory box and packing.

Powering Up!

All xtures must be powered directly o a switched circuit and cannot be run o a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch.

Warning! All xtures must be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something happens to go wrong, visit blizzardpro.com/support and open a support ticket. We’ll be happy to help, honest.

Disclaimer: The information contained in this document are subject to change without

notice. Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions

that may appear in this user manual. We reserve the right to update the existing, or create

a new document to correct any errors or omissions at any time. You can download the

latest version of this document from www.blizzardpro.com.

Author: Date: Last Edited: Date:

J. Thomas 1/24/2022 J. Thomas 1/29/2024

Page 3

Page 4

Safety Instructions

Please read these instructions carefully. They include

important information about the installation, usage and

maintenance of this product.

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the xture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately. NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please open a support ticket at www.blizzardpro.com/support.

Page 4

Page 5

2. MEET THE VERISMO™ PROFILE IP WW

Main Features

• Light source: 300W WW COB LED

• 19°, 26°, 36°, and 50° lens tubes are available

• Color temperature: 3200K, CRI: 98

• 16-bit dimming, with 4 user-selectable dimming curves

• User selectable dimming speeds (low/medium/high)

• 4x manual framing shutters & manual focus

• 1-25Hz strobe eects

• Flicker-free resolution, perfect for video

• Adjustable LED refresh rates (1000-8000 Hz)

• Gobo/pattern holder (B sized gobos)

• IP Rating: IP65

• Aluminum housing (black)

• PowerCON® TRUE1™ compatible in/out power connectors

• 5-pin male/female XLR input & output connections

Control

• Control system: STM32 control chip, DMX-512

• DMX channels: 1/2/3/4-channels

• Easy-to-use 4-button control panel with OLED display

• Operating modes: DMX-512, standalone

DMX Quick Reference (1/2/3/4-Channel Modes)

1-CH 2-CH 3-CH 4-CH What It Does

1 1 1 1 Dimmer (0% <--> 100%)

-- 2 2 2 Dimmer Fine (0% <--> 100%)

-- -- 3 3 Strobe (slow <--> fast)

-- -- -- 4 Dimming Curves

Page 5

Page 6

Verismo™ Prole IP WW Pin-Up Picture

Mounting

Bracket

Gobo

Holder Slot

Framing Shutters

The Rear Connections

Control Menu

*Lens barrels are sold separately with 19°,

26°, 36°, and 50° angles.

Focus Knobs

Lens Barrel

Safety Loop

Locking

Knob

5-pin DMX Out

Power Out

Page 6

5-pin DMX In

Power In

Locking

Knob

Page 7

3. SETUP

Before replacing the fuse, disconnect the power cord.

ALWAYS replace it with the same type and rating.

Fuse Replacement

Verismo™ Prole IP xtures utilize a high-output switch-mode power supply

with an internal fuse. Under normal operating conditions, the fuse should not

require replacement. The fuse is eld replaceable, however it is an advanced procedure suited to qualied individuals. Should the fuse require replacement,

please contact Blizzard Lighting for instructions, or to return your unit for

service.

Connecting A Bunch of Verismo™ Prole IP Fixtures

You can use a serial data link to run light shows when using a DMX-512 controller with two or more xtures. The combined number of channels required by all the xtures on a serial data link determines the number of xtures the

data link can support.

Fixtures on a serial data link must be daisy chained in one single line. Also,

connecting more than 32 xtures on one serial data link without the use of a DMX optically-isolated splitter may result in deterioration of the digital DMX signal. The maximum recommended cable-run distance is 500 meters (1640 ft). The maximum recommended number of xtures on a serial data link is 32 xtures.

Data/DMX Cabling

To link xtures together you’ll need data cables. You should use data-grade

cables that can carry a high quality signal and are less prone to electromagnetic interference.

For instance, Belden© 9841 meets the specications for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but note that

they cannot transmit DMX data as reliably over long distances. The cable should have the following characteristics:

• 2-conductor twisted pair plus a shield

• Maximum capacitance between conductors – 30 pF/ft.

• Maximum capacitance between conductor & shield – 55 pF/ft.

• Maximum resistance of 20 ohms / 1000 ft.

• Nominal impedance 100 – 140 ohms

Page 7

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR connector on the other end. This xture oers both 3-pin and 5-pin connections.

INPUT OUTPUT

DMX -

Common

DMX +

A Word on Termination:

DMX is a resilient communication protocol, however

errors still occasionally occur. Termination reduces signal errors, and therefore best practices include use of a terminator in all circumstances. If you are experiencing

problems with erratic xture behavior, especially over long signal cable runs, a terminator may help improve

performance.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the DMX cable to the female connector

(output) on the controller.

Step 2: Connect the female connector of

the DMX cable to the rst xture’s male

connector (input).

Note: It doesn’t matter which xture address is the rst one connected. We recommend connecting the xtures in terms

of their proximity to the controller, rather than connecting

the lowest xture number rst, and so on.

Step 3: Connect other xtures in the chain

from output to input. You should place a DMX

terminator on the output of the nal xture to

ensure best communication.

Lens Barrels & Focusing

Next Fixture in Chain

DMX OUTDMX IN

First Fixture in Chain

DMX OUTDMX IN

1.) Align and insert a lens tube (sold separately) into the shutter barrel.

2.) Install the top focus knob.

3.) Install the top and bottom focus knobs.

4.) When in use, slide the lens barrel in/out to achieve proper focus, and

tighten the focus knobs to secure the lens.

Page 8

Page 9

Insert the Gobo Holder

The gobo holder slot is on the top side of the shutter barrel and in front of the shutters. It can accommodate standard B sized gobos, with a recommended image size of 40mm.

94.5 mm

Ø 70 mm

200 mm

155.6 mm

68.5

Rotating the Shutter Barrel

1.) Loosen the upper and lower barrel rotation knobs located directly behind the

shutters. Do not remove the barrel rotation knobs.

2.) Rotate the barrel to the desired position (it can rotate up to 34° in either

direction from the centered position).

3.) Once the barrel is positioned, tighten the barrel's rotation knobs to lock it in place.

34° 34°

Mounting & Rigging

This xture may be mounted in any SAFE position provided there is enough room for ventilation. The fan or vent pathway must never be obstructed.

Mount the xture using a suitable "C" or "O"

type clamp. The clamp should be rated to hold

at least 10x the xture’s weight to ensure

structural stability. Do not mount to surfaces of unknown strength, and ensure properly rated rigging is used when mounting

xtures overhead.

IMPORTANT: Regardless of the rigging option you choose for your xtures, always be sure to secure your xture with a safety cable.

Page 9

Page 10

4. OPERATING ADJUSTMENTS

The Control Panel

All the features and dierent modes possible with the Verismo™ Prole IP are accessed by using the control panel on the rear of the xture. There are 4 control buttons under the menu display which allow you to navigate through the various control panel menus.

<MENU>

Is used to navigate to the previous higher-level menu item.

<UP>

Scrolls through menu items and numbers in ascending order.

<DOWN>

Scrolls through menu items and numbers in descending order.

<ENTER>

Is used to select and conrm/store the current selection.

The control panel display shows the menu items you select from the menu map on page #11. When a menu function is selected, the display will show immedi-

ately the rst available option for the selected menu function. To select a menu

item, press <ENTER>.

Use the <UP> and <DOWN> buttons to navigate the menu options. Press the <ENTER> button to select the menu function currently displayed, or to enable

a menu option. To return to the previous option or menu without changing the value, press the <MENU> button.

Page 10

Page 11

Control Panel Menu Structure

DMX Address Set the starting address (1-512)

Control Mode 1-CH

2-CH 3-CH 4-CH

Static Dimmer Dimmer (0% <--> 100%)

Dimmer Fine Fine dimming (0% <--> 100%) Strobe Strobe (slow <--> fast)

Personality Dim Curve Linear

Square law

Inv square law S Curve

Dim Speed O

Low Medium High

Frequency 1000Hz

1200Hz 1500Hz 2000Hz 4000Hz 8000Hz

Fan Mode Full

Auto Silent

DMX Fail Hold

Blackout

Info Version Shows current rmware version

RDM UID Unique RDM ID

Usage Time Power on Total running hrs.

LED total LED running hrs.

Temperature Celsius (°C)

Fahrenheit (°F)

Reset Yes/No Load factory defaults

Page 11

Page 12

DMX Mode

Allows the unit to be controlled by any universal DMX controller.

Select the Channel Mode

1.) Navigate the menu to reach DMX, and press <ENTER>.

2.) Use the <UP/DOWN> buttons to select Control Mode, then <ENTER>.

3.) Then use the <UP/DOWN> buttons to select CH-1, CH-2, CH-3, or CH-

4, and press <ENTER> to conrm.

Select the Starting DMX Address

1.) Navigate the menu to reach DMX, and press <ENTER>.

2.) Use the <UP/DOWN> buttons to select Address, then <ENTER>.

3.) Then use the <UP/DOWN> buttons to select a value from 1-512, and press <ENTER> to conrm.

Static Mode

1.) Navigate the menu to reach Static, and press <ENTER>.

2.) Use the <UP/DOWN> buttons highlight Dimmer, Dimmer Fine, or Strobe, and press <ENTER>.

3.) The Dimmer values will increase/decrease the brightness from 0% to 100%, and Strobe values will change the eect (from slow to fast).

Dimming Curves

1.) Navigate the menu to reach Personality, and press <ENTER>.

2.) Use <UP/DOWN> to highlight Dim Curve, and press <ENTER>.

3.) Then use the <UP/DOWN> buttons to select Linear, Square Law, Inv

Square Law, or S Curve, and press <ENTER>.

Linear Square Law Inv Square Law S Curve

Output

DMX% DMX% DMX% DMX%

Note: Smoother (and slower) dimming capabilities can be achieved with use of the 4

available dimming curve settings.

Output

Dimming Speed

Allows you to set a fade speed of either Low, Medium, or High. This can help simulate fade speeds of incandescent lamps.

1.) Navigate the menu to reach Personality, and press <ENTER>.

2.) Use the <UP/DOWN> buttons to select Dim Speed. Press <ENTER>.

3.) Then use the <UP/DOWN> buttons highlight O, Low, Medium, or High, then press the <ENTER> button.

Page 12

Page 13

Dimming Frequency

1.) Navigate the menu to reach Personality, and press <ENTER>.

2.) Use the <UP/DOWN> buttons to select Frequency, then <ENTER>.

3.) Then use the <UP/DOWN> buttons to select a dimming frequency ranging from 1000Hz-8000Hz, and press <ENTER> to conrm.

DMX Fail

This setting allows you to choose to either hold the last received signal or

blackout the xture if the DMX signal is lost.

1.) Navigate the menu to reach Personality, and press <ENTER>.

2.) Use the <UP/DOWN> buttons to select DMX Fail, then <ENTER>.

3.) Then use the <UP/DOWN> buttons to select Hold or Blackout, and press <ENTER> to conrm.

Fan Settings

1.) Navigate the menu to reach Personality, and press <ENTER>.

2.) Use the <UP/DOWN> buttons to select Fan Mode, then <ENTER>.

3.) Then use the <UP/DOWN> buttons to highlight Full, Auto, or Silent, and press <ENTER> to conrm.

System Reset

1.) Navigate the menu to reach Reset, and press <ENTER>.

2.) Then use the <UP/DOWN> buttons to highlight Yes or No, and press

<ENTER> to conrm, or <MENU> to exit.

DMX Values In-Depth (1/2/3/4-Channel Modes)

1-CH 2-CH 3-CH 4-CH Value What It Does

1 1 1 1 000 <-> 255 Dimmer (0% <--> 100%)

-- 2 2 2 000 <-> 255 Dimmer Fine (0% <--> 100%)

-- -- 3 3 000 <-> 255

-- -- -- 4 000 <-> 050 051 <-> 100 101 <-> 150 151 <-> 255

Strobe

Strobe (slow <--> fast)

Dimming Curves

Linear Square law

Inverse square law S curve

Page 13

Page 14

5. APPENDIX

Keeping Your Verismo™ Prole IP As Good As New

The xture you’ve received is a rugged, tough piece of pro lighting equipment,

and as long as you take care of it, it will take care of you. That said, you’ll need to take care of it if you want it to operate as designed. You should keep the

xture clean, especially if you are using it in an environment with a lot of dust,

fog, haze, wild animals, wild teenagers or spilled drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve

the quality of light output. Keeping the fans free of dust and debris will keep

the xture running cool and prevent damage from overheating.

In transit, keep the xtures in cases. You wouldn’t throw a prized guitar, drumset, or other piece of expensive gear into a gear trailer without a case, and similarly, you shouldn’t even think about doing it with your shiny new light xtures.

Common sense and taking care of your xtures will be the single biggest thing

you can do to keep them running at peak performance and let you worry about designing a great light show, putting on a great concert, or maximizing your client’s satisfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry about sending a defective unit back, or sending a unit in for service. But,

like any complex piece of equipment designed and built by humans, once in a

while, something doesn’t go as planned. If you nd yourself with a xture that isn’t behaving like a good little xture should, you’ll need to obtain a Return Authorization (RA).

Don’t worry, this is easy. Just visit www.blizzardpro.com/support and open a support ticket, and we’ll issue you an RA. Then, you’ll need to send the unit to us using a trackable, pre-paid freight method. We suggest using USPS Priority or UPS. Make sure you carefully pack the xture for transit, and whenever

possible, use the original box & packing for shipping.

When returning your xture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the xture. Please remember

that any shipping damage which occurs in transit to us is the customer’s responsibility, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and must be reported to the carrier immediately upon receipt of the items. Claims must be made within seven (7) days of receipt.

Page 14

Page 15

Tech Specs!

Weight & Dimensions

Dimensions 25.6" x 12.6" x 18" (649 x 320 x 458 mm) Weight (engine only) 19 lbs. (8.6 kg)

Power

Operating Voltage 100-240VAC, 50-60 Hz Power 266W 2.36A, PF: .99

Light Source

LED 300W WW COB LED, 50,000+ hour lifetime

Optical

Luminous Intensity 19° Lens: 27,165 Lux @ 2.5M, 7,421 Lux 5M

26° Lens: 13,336 Lux @ 2.5M, 4,018 Lux 5M 36° Lens: 10,192 Lux @ 2.5M, 3,813 Lux 5M 50° Lens: 6,500 Lux @ 2.5M, 1,808 Lux 5M

Gobo Size B (86mm outer, 40mm image) Color Temperature 3200K, CRI: 98

Noise Level

Measured at 1m distance from

the 4 sides and level with

centerline.

Control

Protocol USITT DMX-512 DMX Channels 1/2/3/4-channel Input/Output 5-pin XLR male/female Operating Modes DMX-512, standalone

Warranty

Fan Mode Front Back Left Right Average

Full 43.2 39.1 41.4 40.6 41.075

Auto 36.7 32.6 33.9 34.1 34.325

Silent 37.3 31.8 34.6 34.8 34.625

2-year limited warranty, does not cover malfunction caused by damage to LEDs.

Dimensional Drawings

25.6" (649 mm)

12.4"

(315 mm)

Page 15

10.1"

(255 mm)

12.6" (320 mm)

18" (458 mm)

Page 16

Enjoy your product!

Our sincerest thanks for your purchase!

--The team @ Blizzard Lighting

Blizzard Lighting Verismo IP Profile WW User guide

Specifications and Main Features

Frequently Asked Questions

User Manual