Blizzard Lighting TOURnado IP EXA User Manual

Blizzard Lighting, LLC

www.blizzardlighting.com

Brookfi eld, WI USA
Copyright (c) 2011

TABLE OF CONTENTS

Flurry™ TRI 1

1. Getting Started 3

What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The Flurry™ TRI 5

Features 5
DMX Quick Reference (13-Channel Mode) 5
DMX Quick Reference (5-Channel Mode) 6
The Flurry Pin-up Picture 6

3. Setup 7

Fuse Replacement 7
Connecting A Bunch Of Flurry™ TRI Lumieres 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9

4. Operating Adjustments 10

The Control Panel 10
Control Panel Menu Structure 11
Additional User Adjustments 12
Setting the pan/tilt/Menu to inverting or non-inverting 12
Setting the DMX channel confi guration 12
Setting the maximum pan angle 12
Setting the maximum tilt angle 12
Service Functions 12
Resetting the fi xture 12
Restoring Factory Defaults 12
Stand-Alone (“Auto”) Mode 13
Master/Slave (“Auto” or “Sound Active”) 13
Easy Controller Mode 13
DMX Mode 13
DMX Channel Values In-Depth (13-Channel Mode) 14
DMX Channel Values In-Depth (5-Channel Mode) 15
Troubleshooting 16

5. Appendix 17

A Quick DMX Lesson 17
Keeping Your Flurry As Good As New 18
Returns (Gasp!) 18
Shipping Issues 18
Tech Specs 19

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 2

1. GETTING STARTED

What’s In The Box?

• 1 x Flurry™ TRI

• An Ever-So-Handy Power Cord

• A Sweet DMX Cable

• A Totally Useful Mounting Bracket

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on purchasing one of the niftiest little moving lights
this side of anywhere! Now that you’ve got your Flurry (or hopefully,
Flurries), you should carefully unpack the box and check the contents
to ensure that all parts are present and in good condition. If anything
looks as if it has been damaged in transit, notify the shipper immedi­ately and keep the packing material for inspection. Again, please save
the carton and all packing materials. If a fi xture must be returned to
the factory, it is important that the fi xture be returned in the original

factory box and packing.

Powering Up!

All fi xtures must be powered directly off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0% to
100% switch.

AC Voltage Switch - Not all fi xtures have a voltage select switch, so
please verify that the fi xture you receive is suitable for your local pow-
er supply. See the label on the fi xture or refer to the fi xture’s specifi -
cations chart for more information. A fi xture’s listed current rating is
its average current draw under normal conditions. Check the fi xture or
device carefully to make sure that if a voltage selection switch exists
that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit
matches the line voltage applied. Damage to your fi xture may
result if the line voltage applied does not match the voltage
indicated on the voltage selector switch. All fi xtures must be

connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, just give us a call or send an email.
We’ll be happy to help, honest.

Blizzard Lighting
PO Box 1874., Brookfi eld, WI 53008 USA
[e-mail] | Phone: [phone]
www.blizzardlighting.com

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 3

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de­cal or rear panel of the fi xture.

• This product is intended for indoor use only.

• To prevent risk of fi re or shock, do not expose fi xture to rain or moisture.

• Make sure there are no fl ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.

• ALWAYS secure fi xture using a safety chain. NEVER carry the fi xture by its
head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech­nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at sup­[e-mail].

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 4

2. MEET THE FLURRY™ TRI

CONTROL FEATURES

• 5 or 13-channel DMX-512 LED moving head lumiere

• Pan: 540 degrees / Tilt: 270 degrees

• RGB color mixing

• Variable electronic strobe

• Variable electronic dimmer (0 – 100%)

• Vector speed channel for pan/tilt, RGB color mixing and color macros

• Built-in movement macros via master/slave or DMX

ADDITIONAL FEATURES

• User-selectable basic or advanced operating modes

• User-selectable pan/tilt ranges
Pan: 540°, 360°, 180°
Tilt: 270°, 180°, 90°

• Compact and lightweight (it kept its new year’s resolution!)

• LED display menu with invert

• Reset to factory settings option

• Display auto on/off

• Pan/tilt invert option

• Fan cooled

OPTIONAL CONTROLLERS

• Easy Controller (CA-9)

DMX Quick Reference (13-Channel Mode)

Channel What It Does

1Pan
2 Pan Fine (16-Bit)
3 Tilt
4 Tilt Fine (16-Bit)
5 Pan/Tilt Speed
6 Dimmer & Strobe
7 Red Intesity
8 Green Intensity
9 Blue Intensity
10 Color Macros
11 Color Speed
12 Movement Macros
13 Reserved

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 5

DMX Quick Reference (5-Channel Mode)

Channel What It Does

1Pan
2 Tilt
3 Dimmer & Strobe
4 Color Macros
5 Reserved

Figure 1: The Flurry Pin-Up Picture

Head

High Power
LED’s

LED
Readout

Control Panel

Figure 2: The Rear Connections

DMX In DMX Out

AC Power

Fuse Cover

110V/220V Switch

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Easy Controller (CA-9)

Page 6

3. SETUP

Fuse Replacement

With a fl at head screwdriver, wedge the
fuse holder out of its housing. Remove the
damaged fuse from its holder and replace
with exact same type fuse. Insert the fuse
holder back in its place and reconnect
power.

Connecting A Bunch of Flurry™ TRI Lumieres

You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more fi xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the fi xtures on a serial data link determines the number of fi x-
tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 fi xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640
ft). The maximum recommended number of fi xtures on a serial data
link is 32 fi xtures.

Data/DMX Cabling

To link fi xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.

For instance, Belden© 9841 meets the specifi cations for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc­es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 7

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the fi x-
ture’s chassis ground. Grounding the common can cause a ground
loop, and your fi xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male
(Input)

Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output)
on the controller.

Step 2: Connect the female connector of the
DMX cable to the fi rst fi xture’s male connec-
tor (input). Note: It doesn’t matter which
fi xture address is the fi rst one connected.
We recommend connecting the fi xtures in
terms of their proximity to the controller,
rather than connecting the lowest fi xture
number fi rst, and so on.

Step 3: Connect other fi xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the fi nal fi xture
to ensure best communication.

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 8

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
the fi rst fi xture.

2. Connect the end of the cable coming from the
fi rst fi xture which will have a (female) 3 pin connec-
tor to the input connector of the next fi xture con-
sisting of a (male) 3 pin connector. Then, proceed
to connect from the output as stated above to the
input of the following fi xture and so on.

A quick note: Often,
the setup for Master­Slave and Standalone
operation requires that
the fi rst fi xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the fi xtures
that follow may also re­quire a slave setting.

Check the “Operating Adjustments” section in this manual for com­plete instructions for this type of setup and confi guration.

Mounting & Rigging

This fi xture may be mounted in any SAFE position provided there is
enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the
fi xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the fi xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting fi xutres overhead.

Adjust the angle of the fi xture by loosening both knobs and tilting the
fi xture. After fi nding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the fi xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 9

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and different modes possible with the Flurry™ TRI are
accessed by using the control panel on the front of the fi xture. There
are 4 control buttons below the LED display which allow you to navi­gate through the various control panel menus.

<MODE/ESC>

Is used to initially access the control panel system, and also navigate
to the previous higher-level menu item.

<UP>

Scrolls through menu items and numbers in ascending order.
<DOWN>

Scrolls through menu items and numbers in descending order.

<ENTER>

Is used to select and confi rm/store the current selection.

The Control Panel LED Display shows the menu items you select from
the menu map on page #11. When a menu function is selected, the
display will show immediately the fi rst available option for the selected
menu function. To select a menu item, press <ENTER>.

Press the <MODE/ESC> button repeatedly until you reach the desired
menu function. Use the <UP> and <DOWN> buttons to navigate the
menu options. Press the <ENTER> button to select the menu function
currently displayed, or to enable a menu option. To return to the previ­ous option or menu without changing the value, press the
<MODE/ESC> button.

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 10

Control Panel Menu Structure

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 11

Additional User Adjustments

TO SET THE PAN TO REVERSED OR NORMAL:

1.) Press the <MODE/ESC> button until it shows

2.) Use the <UP/DOWN> buttons to set to the desired position, press

<ENTER> to confi rm.

TO SET THE TILT TO REVERSED OR NORMAL:

1.) Press the <MODE/ESC> button until it shows

2.) Use the <UP/DOWN> buttons to set to the desired position, press

<ENTER> to confi rm.

TO SET THE LED READOUT TO REVERSED OR NORMAL:

1.) Press the <MODE/ESC> button until it shows

2.) Use the <UP/DOWN> buttons to set to the desired position, press

<ENTER> to confi rm.

TO SET THE DMX CHANNEL CONFIGURATION:

1.) Press the <MODE/ESC> button until it shows or

2.) Use the <UP/DOWN> buttons to set to the desired position, press

<ENTER> to confi rm.

TO SET THE MAXIMUM PAN ANGLE:

1.)Press the <MODE/ESC> button until it shows
or

2.) Use the <UP/DOWN> buttons to set to the desired position, press

<ENTER> to confi rm.

or

or

or

or

TO SET THE MAXIMUM TILT ANGLE:

1.) Press the <MODE/ESC> button until it shows

2.) Use the <UP/DOWN> buttons to set to the desired position, press

<ENTER> to confi rm.

or

Service Functions

TO RESET THE FIXTURE:

1.) Press the <MODE/ESC> button until the display shows

2.) Press <ENTER> to confi rm your selection.

TO RESTORE ALL SETTINGS TO THEIR FACTORY DEFAULTS:

1.) Press the <MODE/ESC> button until the display shows

2.) Press <ENTER> to confi rm your selection.

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 12

Stand-Alone Mode (Auto Mode):

Allows a single unit to run to a factory installed program at one of two speeds.

1.) To set the fi xture in auto mode fast, select .

Once confi rmed the display reads

2.) To set the fi xture in auto mode Slow, select

Once confi rmed the display reads

.

.

.

Master/Slave Mode (Auto or Sound Active):

Allows you to link up to 32 units together without a controller.

1.) Use standard DMX cables to daisy chain your units together via the DMX con-

nector on the rear of the units. It may be necessary to use a terminator at the
last fi xture. For more information about terminators, see page 8.

2.) Choose a unit to function as the Master. Select NAFA/NASL or NStS (see be-

low for readout) depending upon which master mode you want. The master unit
must be the fi rst unit. Finally, chain the units together using DMX cable.

Master Auto

Master Sound

3.) Select slave function by using the <UP>/<DOWN> keys to reach SLAv in

the Master/Auto menu on the slave units, and they will react in the same as the
Master.

Slave

or .

becomes when confi rmed.

becomes when confi rmed.

Easy Controller Mode

Allows you to use the optional CA-9 Easy Controller for basic control functionality.

1.) Connect the CA-9 Easy Controller to the controller port on the rear panel of

the unit.

2.) Select the Easy Controller function by using the <UP>/<DOWN> keys to

reach NStc in the menu structure.

Easy Control

3.) In Easy Controller Mode, the fi xture will react as follows:

Button What it Does...

Standby Blackout.
Function 1st click = Strobe On, 2nd click = Strobe Off.
Mode 1st click = Sound Active Mode (Remote LED will be on).

DMX Mode

Allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, please read the DMX Primer on page #17.

2nd click = Auto Mode (LED will be off).

becomes when confi rmed.

1.) The default mode for the fi xture is DMX, which appears as on the

LED Readout.

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 13

DMX Channel Values (13 Channel Mode)

Channel Channel Value Does...

1 000 <-> 255 Pan

2 000 <-> 255 Pan Fine

3 000 <-> 255 Tilt

4 000 <-> 255 Tilt Fine

5 000 <-> 255 Pan/Tilt Speed (Normal to Slow)

6

7 000 <-> 255

8 000 <-> 255

9 000 <-> 255

10

11 000 <-> 255 Color Speed

12

13 Reserved

000 <-> 007
008 <-> 134
135 <-> 239
240 <-> 255

000 <-> 007
008 <-> 021
022 <-> 035
036 <-> 049
050 <-> 062
063 <-> 076
077 <-> 090
091 <-> 104
105 <-> 118
119 <-> 132
133 <-> 146
147 <-> 160
161 <-> 174
175 <-> 188
189 <-> 202
203 <-> 216
217 <-> 230
231 <-> 243
244 <-> 255

000 <-> 007
008 <-> 023
024 <-> 039
040 <-> 055
056 <-> 071
072 <-> 087
088 <-> 104
105 <-> 117
118 <-> 135
136 <-> 151
152 <-> 167
168 <-> 183
184 <-> 199
200 <-> 215
216 <-> 231
232 <-> 247
247 <-> 255

Dimmer/Strobe

Closed
100%-0% Dimming
Strobe (Slow-Fast)
Open

Red

0-100%

Green

0-100%

Blue

0-100%

Color Macros

No Function
White
Red
Green
Blue
Cyan
Magenta
Yellow
Purple
Orange
Chartruese
Pink
Brown
Gold
Crimson
Violet
Crepe
Color Change Macro #1
Color Change Macro #2

Movement/Color Macros

No Function
Automatic Program #1
Automatic Program #2
Automatic Program #3
Automatic Program #4
Automatic Program #5
Automatic Program #6
Automatic Program #7
Automatic Program #8
Sound Active Program #1
Sound Active Program #2
Sound Active Program #3
Sound Active Program #4
Sound Active Program #5
Sound Active Program #6
Sound Active Program #7
Sound Active Program #8

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 14

DMX Channel Values (5 Channel Mode)

Channel Channel Value Does...

1 000 <-> 255 Pan

2 000 <-> 255 Tilt

3

4

5 Reserved

000 <-> 007
008 <-> 134
135 <-> 239
240 <-> 255

000 <-> 007
008 <-> 021
022 <-> 035
036 <-> 049
050 <-> 062
063 <-> 076
077 <-> 090
091 <-> 104
105 <-> 118
119 <-> 132
133 <-> 146
147 <-> 160
161 <-> 174
175 <-> 188
189 <-> 202
203 <-> 216
217 <-> 230
231 <-> 243
244 <-> 255

Dimmer/Strobe

Closed
100%-0% Dimming
Strobe (Slow-Fast)
Open

Color Macros

No Function
White
Red
Green
Blue
Cyan
Magenta
Yellow
Purple
Orange
Chartruese
Pink
Brown
Gold
Crimson
Violet
Crepe
Color Change Macro #1
Color Change Macro #2

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 15

Troubleshooting

Symptom Solution

Fixture Auto­Shut Off

Beam is Dim Check optical system and clean excess dust/grime. Also

No Light Output Check to ensure fi xture is operating under correct mode, IE

Chase Speed
Too Fast/Slow

No Power Check fuse, AC cord and circuit for malfunction.
Blown Fuse Check AC cord and circuit for damage, verify that moving

Slow Movement Verify that 220V/110V switch is in the correct position, if

No Response to
Audio

Fixture Not
Responding /
Responding Er­raticly

Intermittant
Lamp

Remote Doesn’t
Work

Fixture Moving
On Its Own

Check the fan in the fi xture. If it is stopped or moving
slower than normal, the unit may have shut itself off due to
high heat. This is to protect the fi xture from overheating.
Clear the fan of obstructions, or return the unit for service.

ensure that the 220V/110V switch is in the correct position,
if applicable.

sound active/auto/DMX/Etc., if applicable. Contact service
for more information.

Check to ensure proper setup of speed adjustment.

parts are not restricted and that unit’s ventilation is not
obstructed

applicable. Also check that speed channels are set appropri­ately.

Verify that the fi xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.

Make sure all connectors are seated properly and securely.
Use Only DMX Cables.
Install a Terminator.
Check all cables for defects.
Reset fi xture(s).

Check lamp for properly installation.
Relamp, lamp may have reached end of life.

Verify remote control cable is installed properly and securely.
Verify remote is correct type (CA-9 or other as applicable.)

Verify proper mode of operation. Is the fi xture in “Auto”
mode?

If your problem isn’t listed, or if problems persist,

please contact support: [e-mail].

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 16

5. APPENDIX

A Quick Lesson On DMX

DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre
Technology (USITT) as a standardized method for connecting lighting consoles to lighting
dimmer modules. It was revised in 1990 and again in 2000 to allow more fl exibility. The
Entertainment Services and Technology Association (ESTA) has since assumed control over
the DMX512 standard. It has also been approved and recognized for ANSI standard clas­sifi cation.

DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common
communications standard used by lighting and related stage equipment.

DMX provides up to 512 control “channels” per data link. Each of these channels was origi­nally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting
console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an
8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb
being completely off while 255 corresponds to the light bulb being fully on.

DMX data is transmitted at 250,000 bits per second using the RS-485 transmission stan­dard over two wires. As with microphone cables, a grounded cable shield is used to prevent
interference with other signals.

There are fi ve pins on a DMX connector: a wire for ground (cable shield), two wires for
“Primary” communication which goes from a DMX source to a DMX receiver, and two wires
for a “Secondary” communication which goes from a DMX receiver back to a DMX source.
Generally, the “Secondary” channel is not used so data fl ows only from sources to receiv-
ers. Hence, most of us are most familiar with DMX-512 as being employer over typical
3-pin “mic cables,” although this does not conform to the defi ned standard.

DMX is connected using a daisy-chain confi guration where the source connects to the input
of the fi rst device, the output of the fi rst device connects to the input of the next device,
and so on. The standard allows for up to 32 devices on a single DMX link.

Each receiving device typically has a means for setting the “starting channel number” that
it will respond to. For example, if two 6-channel fi xtures are used, the fi rst fi xture might
be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next
fi xture would be set to start at channel 7 so it would respond to channels 7 through 12.

The greatest strength of the DMX communications protocol is that it is very simple and
robust. It involves transmitting a reset condition (indicating the start of a new “packet”),
a start code, and up to 512 bytes of data. Data packets are transmitted continuously. As
soon as one packet is fi nished, another can begin with no delay if desired (usually another
follows within 1 ms). If nothing is changing (i.e. no lamp levels change) the same data will
be sent out over and over again. This is a great feature of DMX -- if for some reason the
data is not interpreted the fi rst time around, it will be re-sent shortly.

Not all 512 channels need to be output per packet, and in fact, it is very uncommon to fi nd
all 512 used. The fewer channels are used, the higher the “refresh” rate. It is possible to
get DMX refreshes at around 1000 times per second if only 24 channels are being trans­mitted. If all 512 channels are being transmitted, the refresh rate is around 44 times per
second.

In summary, since its design and evolution in the 1980’s DMX has become the standard
for lighting control. It is fl exible, robust, and scalable, and its ability to control everything
from dimmer packs to moving lights to foggers to lasers makes it an indispensible tool for
any lighting designer or lighting performer.

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 17

Keeping Your Flurry As Good As New

The fi xture you’ve received is a rugged, tough piece of pro lighting equip-
ment, and as long as you take care of it, it will take care of you. That said, like
anything, you’ll need to take care of it if you want it to operate as designed.
You should absolutely keep the fi xture clean, especially if you are using it in an
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled
drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve
the quality of light output. Keeping the fans free of dust and debris will keep
the fi xture running cool and prevent damage from overheating.

In transit, keep the fi xtures in cases. You wouldn’t throw a prized guitar,
drumset, or other piece of expensive gear into a gear trailer without a case,
and similarly, you shouldn’t even think about doing it with your shiny new light
fi xtures.

Common sense and taking care of your fi xtures will be the single biggest thing
you can do to keep them running at peak performance and let you worry about
designing a great light show, putting on a great concert, or maximizing your cli­ent’s satistfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But, like
any complex piece of equipment designed and built by humans, once in a while,
something doesn’t go as planned. If you fi nd yourself with a fi xture that isn’t
behaving like a good little fi xture should, you’ll need to obtain a Return Authori-
zation (RA).

Don’t worry, this is easy. Just send an email to [e-mail],
and we’ll issue you an RA. Then, you’ll need to send the unit to us using a
trackable, pre-paid freight method. We suggest using USPS Priority or UPS.
Make sure you carefully pack the fi xture for transit, and whenever possible, use
the original box & packing for shipping.

When returning your fi xture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the fi xture. Please remember that
any shipping damage which occurs in transit to us is the customer’s responsibil­ity, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and
must be reported to the carrier immediately upon receipt of the items.
Claims must be made within seven (7) days of receipt.

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

Page 18

Tech Specs!

Weight & Dimensions

Length 6.8 inches (173 mm)
Width 6.8 inches (173 mm)
Height 9.8 inches (249 mm)
Weight 6.7 lbs (3.8 kg)

Power

Operating Voltage 110-230VAC, 50-60 Hertz (autoranging)
Fuse 2A 250V
Power Consumption 120W

Light Source

LED 18x3W (TRI-Color), 100,000 hours, Edison®

Brand.

Optical

Beam Angle 18 degrees
Luminous Intensity 12,110 (full white) lux/1m

Movement Range

Pan 540 degrees
Tilt 270 degrees

Thermal

Max. Operating Temp. 104 degrees F (40 degrees C) ambient

Control

Protocol USITT DMX-512
DMX Channels 5 or 13 (User Selectable)
Input 3-pin XLR Male
Output 3-pin XLR Female
Optional Controller CA-9 Easy Controller

Military Callsign

Foxtrot Tango

2-year limited warranty, does not cover mal-

Warranty

Flurry TRI Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC

function caused by damage to LED’s.

Page 19

Enjoy your product!

Our sincerest thanks for your purchase!

--The team @ Blizzard Lighting