Blizzard Lighting Rocklite Raygun User Manual Rev A

Blizzard Lighting, LLC

www.blizzardlighting.com

Brookfi eld, WI USA

Copyright © 2012

TABLE OF CONTENTS

ROCKLITE™ RAYGUN LED 1

1. Getting Started 3

What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The ROCKLITE™ RAYGUN LED 5

Features 5
DMX Quick Reference 5

The RAYGUN

3. Setup 7

Fuse Replacement 7
Connecting A Bunch Of ROCKLITE™ RAYGUN

Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9

™ Pin-up Picture 6

™ PAR Cans 7

4. Operating Adjustments 10

Navigating The Control Panel 10
Control Panel Menu Structure 11
DMX Mode 12
Master/Slave Mode 12
Sound Active Mode 12
Standalone (Program) Mode 12
LED Display On/Off 12
DMX Channel Values In-Depth 13
Troubleshooting 14

5. Appendix 15

A Quick DMX Lesson 15
Keeping Your RAYGUN™ As Good As New 16
Returns (Gasp!) 16
Shipping Issues 16
Tech Specs 17

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 2

1. GETTING STARTED

What’s In The Box?

• 1x ROCKLITE™ RAYGUN™ LED Very Narrow Spot LED Fixture

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on purchasing The ROCKLITE™ RAYGUN™! You’ll now
be able to repel any alien takeover while headbanging your permed
mullet well into the wee hours of the morning! Well, now that you’ve
got your RAYGUN™ (or hopefully, RAYGUNs!), You should carefully
unpack the box and check the contents to ensure that all parts are
present and in good condition. If anything looks as if it has been dam­aged in transit, notify the shipper immediately and keep the packing
material for inspection. Again, please save the carton and all packing
materials. If a fi xture must be returned to the factory, it is important

that the fi xture be returned in the original factory box and packing.

Powering Up!

All fi xtures must be powered directly off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0% to
100% switch.

AC Voltage Switch - Not all fi xtures have a voltage select switch, so
please verify that the fi xture you receive is suitable for your local pow-
er supply. See the label on the fi xture or refer to the fi xture’s specifi -
cations chart for more information. A fi xture’s listed current rating is
its average current draw under normal conditions. Check the fi xture or
device carefully to make sure that if a voltage selection switch exists
that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit
matches the line voltage applied. Damage to your fi xture may
result if the line voltage applied does not match the voltage
indicated on the voltage selector switch. All fi xtures must be

connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, just give us a call or send an email.
We’ll be happy to help, honest.

Blizzard Lighting
W220 N1531 Jericho Ct. Suite E, Waukesha, WI 53186 USA
[e-mail]
www.blizzardlighting.com
414-395-8365

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 3

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de­cal or rear panel of the fi xture.

• This product is intended for indoor use only.

• To prevent risk of fi re or shock, do not expose fi xture to rain or moisture.

• Make sure there are no fl ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.

• ALWAYS secure fi xture using a safety chain. NEVER carry the fi xture by its
cord. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech­nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at sup­[e-mail].

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 4

2. MEET THE ROCKLITE™ RAYGUN LED PAR

CONTROL FEATURES

• Capable of fi ghting intergalactic crime with its ultra-bright 50W white
LED light source

• Variable electronic strobe

• Variable electronic dimmer

• Built-in color & chase macros via DMX

• Built-in automated programs via master/slave

• Built-in sound active programs in standalone & DMX

ADDITIONAL FEATURES

• Rugged and well-built (It hits the gym regularly)

• Light source: 1x 50-watt US-Made Luminus CBT-90 White LED,
6,500K, 50,000 Hours

• Internal Fan Cooling

• Dual mounting brackets for positioning fl exibility

DMX Quick Reference - 3/5 Channel Mode

Channel What It Does

1 Color Wheel
2 Dimmer
3 Strobe
4 N/A Built-In Programs & Sound Active
5 N/A Remote Reset

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 5

Figure 1: The RAYGUN™ Pin-Up Picture

“The Business End” -- Large­Scale Collimating Lens

Mounting Yokes &
Adjustment/Locking Knobs

Figure 2: The Rear Connections

LED Control Panel

Grounding
Screw

Heavy-Gauge
Spun Aluminum
Enclosure

DMX In DMX Out

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 6

3. SETUP

Fuse Replacement

CAUTION! The ROCKLITE™ RAYGUN utilizes a high-output switch-

mode power supply with an internal fuse. Under normal operating
conditions, the fuse should not require replacement. The fuse is fi eld
replaceable, however it is an advanced procedure suited to qualifi ed
individuals. Should your ROCKLITE™ fuse require replacement, please
contact Blizzard Lighting for instructions, or to return your unit for
service.

Connecting A Bunch of ROCKLITE™ RAYGUN Fixtures

You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more fi xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the fi xtures on a serial data link determines the number of fi x-
tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 fi xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640
ft.). The maximum recommended number of fi xtures on a serial data
link is 32 fi xtures.

Data/DMX Cabling

To link fi xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.

For instance, Belden© 9841 meets the specifi cations for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc­es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft..
Maximum capacitance between conductor & shield – 55 pF/ft..
Maximum resistance of 20 ohms / 1000 ft..
Nominal impedance 100 – 140 ohms

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 7

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the fi x-
ture’s chassis ground. Grounding the common can cause a ground
loop, and your fi xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male
(Input)

Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output)
on the controller.

Step 2: Connect the female connector of the
DMX cable to the fi rst fi xture’s male connec-
tor (input). Note: It doesn’t matter which
fi xture address is the fi rst one connected.
We recommend connecting the fi xtures in
terms of their proximity to the controller,
rather than connecting the lowest fi xture
number fi rst, and so on.

Step 3: Connect other fi xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the fi nal fi xture
to ensure best communication.

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 8

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
the fi rst fi xture.

2. Connect the end of the cable coming from the
fi rst fi xture which will have a (female) 3 pin connec-
tor to the input connector of the next fi xture con-
sisting of a (male) 3 pin connector. Then, proceed
to connect from the output as stated above to the
input of the following fi xture and so on.

A quick note: Often,
the setup for Master­Slave and Standalone
operation requires that
the fi rst fi xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the fi xtures
that follow may also re­quire a slave setting.

Check the “Operating Adjustments” section in this manual for com­plete instructions for this type of setup and confi guration.

Mounting & Rigging

This fi xture may be mounted in any SAFE position provided there is
enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the
fi xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the fi xture’s weight to ensure structural sta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting fi xtures overhead.

Adjust the angle of the fi xture by loosening both knobs and tilting the
fi xture. After fi nding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the fi xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 9

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and different modes possible with the ROCKLITE™ LED
are accessed by using the control panel on the rear of the fi xture.
There are 4 control buttons below the LED display which allow you to
navigate through the various control panel menus.

<MENU>

Is used to navigate to the previous higher-level menu item.

<UP>

Scrolls through menu items and numbers in ascending order.
<DOWN>

Scrolls through menu items and numbers in descending order.

<ENTER>

Is used to select and confi rm/store the current selection.

The Control Panel LED Display shows the menu items you select from
the menu map on page #11. When a menu function is selected, the
display will show immediately the fi rst available option for the selected
menu function. To select a menu item, press <ENTER>.

Press the <MENU> button repeatedly until you reach the desired
menu function. Use the <UP> and <DOWN> buttons to navigate the
menu options. Press the <SAVE> button to select the menu function
currently displayed, or to enable a menu option. To return to the previ­ous option or menu without changing the value, press the
<MENU> button.

Page 10

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Control Panel Menu Structure

A001 <ENTER>

3CH
5CH

<UP/DOWN/ENTER>

A001 - A512

<UP/DOWN/ENTER>

Soud <ENTER> Soud <ENTER>
RuN0 <ENTER> RuN0 <ENTER>
RuN1 <ENTER> RuN1 <ENTER>
RuN2 <ENTER> RuN2 <ENTER>

L000 <ENTER> L000-L255 <ENTER>
P000 <ENTER> P000-P255 <ENTER>

LEoN <ENTER> LEoN - LoFF <UP/DOWN/ENTER>

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 11

DMX Mode

Allows the unit to be controlled by any universal DMX controller in one of 2 channel modes.

1.) The default mode for the fi xture is DMX, which appears as
Readout.

2.) To select the DMX personality (channel mode), select either
nel Mode), or

3.) Then, use the <UP/DOWN> buttons to select the correct address between

5 Ch (5-Channel Mode), then hit <ENTER> to confi rm.

A001 on the LED

3 Ch (3-Chan-

A001-A512, then hit <ENTER> to confi rm.

Stand-Alone, Master/Slave, Sound Active Modes:

Allows a single or Master/Slaved units to run factory installed programs at user selectable
speeds.

1.) To set the fi xture in one of 3 standalone automatic operating modes, select

RuN 0 - RuN 2

To confi rm, press the <ENTER> button.

2.) To set the fi xture to a specifi c color (or color scroll), use the <MENU> button
to reach

channel you wish to display. For instance, to display Yellow, you would select
a value between
scroll, you would select a value around

to confi rm. (See DMX Values on P. 13)

P000-P255. This value corresponds to the DMX value for the color

P080-P111. To select a medium-speed clockwise color

P160, then press the <ENTER> button

3.) Next, use the <MENU> button to reach
responds to the DMX value for the dimmer channel. For instance, to cause the

fi xture to output at approximately 25%, you would select a value of
cause the fi xture to output at 100%, you would select

<ENTER> button to confi rm.

4.) To set the fi xture as a slave unit, select

Sound Active Mode:

1.) To use sound active mode, select
to confi rm.

Soud, then press the <ENTER> button

L000-L255. This value cor-

L064. To

L255, then press the

A001, and hit <ENTER>.

To Turn the LED Display On/Off:

Allows the user to enable/display the LED display while the fi xture is in operation.

1.) Use the <MENU> button to reach LEoN / LoFF

2.) Now, select the status by using the <UP> and <DOWN> buttons to select

LEoN (LED Display On), or LoFF (LED Display Off). To confi rm, press the

<ENTER> button.

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 12

DMX Values In-Depth (3 & 5-Channel Mode)

Channel Value What It Does

(3 Ch.)

1

000 <--> 007
008 <--> 015
016 <--> 031
032 <--> 047
048 <--> 063
064 <--> 079
080 <--> 111
112 <--> 128
129 <--> 192
193 <--> 255

2 000 <--> 255 Dimmer (0% <--> 100%)
3

000 <--> 015
016 <--> 255

4

000 <--> 002
003 <--> 199
200 <--> 255

5

000 <--> 254
255 <--> 255

Color

White / Open
Pink
Orange
Blue
Green
Magenta
Yellow
Cyan
Color Wheel Scroll CW (Slow <--> Fast)
Color Wheel Scroll CCW (Fast <--> Slow)

Strobe

Open / No Function
Strobe (Slow <--> Fast)

N/A Built-In Programs

N/A Fixture Reset

What It Does
(5 Ch.)

No Function
Built-In Programs
Sound Active Mode

No Function
Reset (Hold For 5 Seconds)

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 13

Troubleshooting

Symptom Solution

Fixture Auto­Shut Off

Beam is Dim Check optical system and clean excess dust/grime. Also

No Light Output Check to ensure fi xture is operating under correct mode, IE

Chase Speed
Too Fast/Slow

No Power Check fuse, AC cord and circuit for malfunction.
Blown Fuse Check AC cord and circuit for damage, verify that moving

Slow Movement Verify that 220V/110V switch is in the correct position, if

No Response to
Audio

Check the fan in the fi xture. If it is stopped or moving
slower than normal, the unit may have shut itself off due to
high heat. This is to protect the fi xture from overheating.
Clear the fan of obstructions, or return the unit for service.

ensure that the 220V/110V switch is in the correct position,
if applicable.

sound active/auto/DMX/Etc., If applicable. Contact service
for more information.

Check to ensure proper setup of speed adjustment.

parts are not restricted and that unit’s ventilation is not
obstructed

applicable. Also check that speed channels are set appropri­ately.

Verify that the fi xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.

Fixture Not
Responding /
Responding Er­ratically

Intermittent
Lamp

Remote Doesn’t
Work

Fixture Moving
On Its Own

If your problem isn’t listed, or if problems persist,

please contact support: [e-mail].

Make sure all connectors are seated properly and securely.
Use Only DMX Cables.
Install a Terminator.
Check all cables for defects.
Reset fi xture(s).

Check lamp for properly installation.
Relamp, lamp may have reached end of life.

Verify remote control cable is installed properly and securely.
Verify remote is correct type (CA-9 or other as applicable.)

Verify proper mode of operation. Is the fi xture in “Auto”
mode?

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 14

5. APPENDIX

A Quick Lesson On DMX

DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre
Technology (USITT) as a standardized method for connecting lighting consoles to lighting
dimmer modules. It was revised in 1990 and again in 2000 to allow more fl exibility. The
Entertainment Services and Technology Association (ESTA) has since assumed control over
the DMX512 standard. It has also been approved and recognized for ANSI standard clas­sifi cation.

DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common
communications standard used by lighting and related stage equipment.

DMX provides up to 512 control “channels” per data link. Each of these channels was origi­nally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting
console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an
8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb
being completely off while 255 corresponds to the light bulb being fully on.

DMX data is transmitted at 250,000 bits per second using the RS-485 transmission stan­dard over two wires. As with microphone cables, a grounded cable shield is used to prevent
interference with other signals.

There are fi ve pins on a DMX connector: a wire for ground (cable shield), two wires for
“Primary” communication which goes from a DMX source to a DMX receiver, and two wires
for a “Secondary” communication which goes from a DMX receiver back to a DMX source.
Generally, the “Secondary” channel is not used so data fl ows only from sources to receiv-
ers. Hence, most of us are most familiar with DMX-512 as being employer over typical
3-pin “mic cables,” although this does not conform to the defi ned standard.

DMX is connected using a daisy-chain confi guration where the source connects to the input
of the fi rst device, the output of the fi rst device connects to the input of the next device,
and so on. The standard allows for up to 32 devices on a single DMX link.

Each receiving device typically has a means for setting the “starting channel number” that
it will respond to. For example, if two 6-channel fi xtures are used, the fi rst fi xture might
be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next
fi xture would be set to start at channel 7 so it would respond to channels 7 through 12.

The greatest strength of the DMX communications protocol is that it is very simple and
robust. It involves transmitting a reset condition (indicating the start of a new “packet”),
a start code, and up to 512 bytes of data. Data packets are transmitted continuously. As
soon as one packet is fi nished, another can begin with no delay if desired (usually another
follows within 1 ms). If nothing is changing (i.e. no lamp levels change) the same data will
be sent out over and over again. This is a great feature of DMX -- if for some reason the
data is not interpreted the fi rst time around, it will be re-sent shortly.

Not all 512 channels need to be output per packet, and in fact, it is very uncommon to fi nd
all 512 used. The fewer channels are used, the higher the “refresh” rate. It is possible to
get DMX refreshes at around 1000 times per second if only 24 channels are being trans­mitted. If all 512 channels are being transmitted, the refresh rate is around 44 times per
second.

In summary, since its design and evolution in the 1980’s DMX has become the standard
for lighting control. It is fl exible, robust, and scalable, and its ability to control everything
from dimmer packs to moving lights to foggers to lasers makes it an indispensable tool for
any lighting designer or lighting performer.

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 15

Keeping Your ROCKLITE™ As Good As New

The fi xture you’ve received is a rugged, tough piece of pro lighting equip-
ment, and as long as you take care of it, it will take care of you. That said, like
anything, you’ll need to take care of it if you want it to operate as designed.
You should absolutely keep the fi xture clean, especially if you are using it in an
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled
drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve
the quality of light output. Keeping the fans free of dust and debris will keep
the fi xture running cool and prevent damage from overheating.

In transit, keep the fi xtures in cases. You wouldn’t throw a prized guitar,
drumset, or other piece of expensive gear into a gear trailer without a case,
and similarly, you shouldn’t even think about doing it with your shiny new light
fi xtures.

Common sense and taking care of your fi xtures will be the single biggest thing
you can do to keep them running at peak performance and let you worry about
designing a great light show, putting on a great concert, or maximizing your cli­ent’s satisfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But, like
any complex piece of equipment designed and built by humans, once in a while,
something doesn’t go as planned. If you fi nd yourself with a fi xture that isn’t
behaving like a good little fi xture should, you’ll need to obtain a Return Authori-
zation (RA).

Don’t worry, this is easy. Just send an email to [e-mail],
and we’ll issue you an RA. Then, you’ll need to send the unit to us using a
trackable, pre-paid freight method. We suggest using USPS Priority or UPS.
Make sure you carefully pack the fi xture for transit, and whenever possible, use
the original box & packing for shipping.

When returning your fi xture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the fi xture. Please remember that
any shipping damage which occurs in transit to us is the customer’s responsibil­ity, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and
must be reported to the carrier immediately upon receipt of the items.
Claims must be made within seven (7) days of receipt.

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 16

Tech Specs!

Weight & Dimensions

Length 14.25 inches (360 mm)
Width 11 inches (278 mm)
Height 7.75 inches (197 mm)
Weight 7.2 lbs (3.25 kg)

Power

Operating Voltage 90-230VAC, 50-60 Hertz, Autoranging
Fuse 3A 250V

30W @ 120VAC

Power Consumption

.35A Operating, .32A Inrush
Power Factor: .66

Light Source

LED 50-watt Luminus CBT-90 White LED, 6,500

Color Temperature, 50,000 Hours

Optical

Beam Angle 2.5 degree
Luminous Intensity 28,220 Lux @ 1m

13,180 Lux @ 2m

Thermal

Max. Operating Temp. 104 degrees F (40 degrees C) ambient

Control

Protocol USITT DMX-512
DMX Channels 3 / 5
Input 3-pin XLR Male
Output 3-pin XLR Female

Standalone, Master/Slave, Sound Active,

Other Operating Modes

Color Preset

Poison or Def Leppard?

Yes.

2-year limited warranty, does not cover mal-

Warranty

function caused by damage to LED’s.

Page 17

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

This page intentionally left blank.

ROCKLITE RAYGUN Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC

Page 18

This page intentionally left blank.

Enjoy your product!

Our sincerest thanks for your purchase!

--The team @ Blizzard Lighting