Blizzard Lighting, LLC
www.blizzardlighting.com
Wisconsin, USA
Copyright (c) 2011
TABLE OF CONTENTS
The Puck™ Q12 LED PAR Can 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The Puck™ Q12 LED PAR Can 5
Features 5
DMX Quick Reference (4 and 7-Channel Modes) 5
The Puck
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of Puck™ Q12 LED PAR Cans 7
Data/DMX Cables 7
4. Operating Adjustments 8
™ Q12 Pin-up Picture 6
DMX Mode & DMX Mode Selection 8
Master/Slave Mode 8
Sound Active Mode 8
Custom Color Display 8
Fixture running hour display 8
Troubleshooting 9
5. Appendix 10
Keeping The Puck™ Q12 LED PAR Can As Good As New 10
Returns (Gasp!) 10
Shipping Issues 10
Tech Specs 11
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 2
1. GETTING STARTED
What’s In The Box?
• 1 x Puck™ Q12 Flat LED PAR Fixture
• 1x IEC Power Cord
• This Lovely User Manual
Getting It Out Of The Box
Congratulations on being completely and utterly qtastic! Now that
you’ve got The Puck™ Q12 (or hopefully, Pucks!), you should carefully
unpack the box and check the contents to ensure that all parts are
present and in good condition. If anything looks as if it has been damaged in transit, notify the shipper immediately and keep the packing
material for inspection. Again, please save the carton and all packing
materials. If a fi xture must be returned to the factory, it is important
that the fi xture be returned in the original factory box and packing.
Powering Up!
All fi xtures must be powered directly off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0% to
100% switch.
AC Voltage Switch - Not all fi xtures have a voltage select switch, so
please verify that the fi xture you receive is suitable for your local pow-
er supply. See the label on the fi xture or refer to the fi xture’ s specifi -
cations chart for more information. A fi xture’s listed current rating is
its average current draw under normal conditions. Check the fi xture or
device carefully to make sure that if a voltage selection switch exists
that it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit
matches the line voltage applied. Damage to your fi xture may
result if the line voltage applied does not match the voltage
indicated on the voltage selector switch. All fi xtures must be
connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email.
We’ll be happy to help, honest.
Blizzard Lighting
W220 N1531 Jericho Ct. Suite E, Waukesha, WI 53186 USA
support@blizzardlighting.com
www.blizzardlighting.com
1.866.493.6025
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 3
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fi xture.
• This product is intended for indoor use only.
• To prevent risk of fi re or shock, do not expose fi xture to rain or moisture.
• Make sure there are no fl ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure fi xture using a safety chain. NEVER carry the fi xture by its
cord. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at support@blizzardlighting.com.
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 4
2. MEET The Puck™ Q12A / Q12W Flat LED PAR
Can
CONTROL FEATURES
• RGBA color mixing via 12x 10-Watt Quad Color RGBA LEDs (Q12A)
• RGBW color mixing via 12x 10-Watt Quad Color RGBW LEDs (Q12W)
• Variable electronic strobe
• Variable electronic dimmer
• Built-in automated programs via DMX and master/slave
• Built-in sound active programs
• Full RGBA/RGBW color mixing in standalone and master/slave
• RGBA/RGBW (4-Channel) and extended (7-Channel) DMX modes
ADDITIONAL FEATURES
• Lightweight and Compact (It kept its New Years’ resolution!)
• 4-Button LED control panel for easy programming
• Light source: 12x 10-Watt LEDs, Quad-Color
• Dual bracket for fl exibility in mounting
• Power outlet for fi xture linking (up to 10 fi xtures)
DMX Quick Reference (7-Channel Mode)
Channel What It Does
1 Dimmer
2 Red Intensity
3 Green Intensity
4 Blue Intensity
5 Amber / White Intensity
6 Strobe (0-15 off, 16-255 strobe
slow <-> fast)
7 Color Macros (slow <-> fast)
DMX Quick Reference (4-Channel Mode)
Channel What It Does
1 Red Intensity
2 Green Intensity
3 Blue Intensity
4 Amber / White Intensity
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 5
Figure 1: The Puck™ Q12 Pin-Up Picture
Dual Mounting
Yokes
Quad-Color
LED’s
Figure 2: The Rear Connections
DMX In DMX Out
LED Control Panel
Microphone
Ridiculously thin!
AC Power In/Out
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 6
3. SETUP
Fuse Replacement
With a fl at head screwdriver, wedge the
fuse holder out of its housing. Remove the
damaged fuse from its holder and replace
with exact same type fuse. Insert the fuse
holder back in its place and reconnect
power.
Connecting A Bunch of Puck™ Q12 Flat LED PAR Cans
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more fi xtures set to sync in mas-
ter/slave operating mode. The combined number of channels required
by all the fi xtures on a serial data link determines the number of fi x-
tures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 fi xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640
ft). The maximum recommended number of fi xtures on a serial data
link is 32 fi xtures.
Data/DMX Cabling
To link fi xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specifi cations for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distances. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 7
4. OPERATING ADJUSTMENTS
NOTE: After making any adjustment, the fi xture will return to the correct mode
after approximately 5 seconds.
DMX Mode
Allows the unit to be controlled by any universal DMX controller.
1.) The default mode for the fi xture is DMX, which appears as
Readout. Use the <ENTER> button then the <UP> and <DOWN> buttons to
choose a channel between
2.) To change between 3 and 6 channel DMX mode, select
<ENTER>. Select either
fi rm.
1 and 512. Press <ENTER> again to confi rm.
7Ch or 4Ch, then press <ENTER> again to con-
Addr on the LED
ChNd, then press
Master/Slave Mode (Auto/Sound Active/Color Preset/Custom):
Allows you to link up to 32 units together without a controller.
1.) Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the units.
2.) Choose a unit to function as the Master. Select MAST. The master unit must
be the fi rst unit. Finally, chain the units together using DMX cable.
Master
3.) Select slave function by using the <UP>/<DOWN> keys to reach SLAV in
the Master/Auto menu on the slave units, and they will react in the same as the
Master.
Slave
4.) On the master fi xture, use the <UP>/<DOWN> keys to reach SHND, which
allows you to select the Master/Slave mode.
SLNd then NASt to confi rm.
SLNd then SLAu to confi rm.
Sound active
Auto mode
Color preset
SoUn then <ENTER> to confi rm.
CoLo then Auto, then <ENTER> to confi rm.
CoLo then CoL 1 - CoL 15, <ENTER>.
To set a custom color in Master/Slave / Standalone Mode:
Using this function, you can select any color by adjusting the Red, Green, Blue and White/
Amber values from 0-255. You may also adjust the color balance of the fi xture.
Please note that modifying the values in this step will affect ALL modes, therefore
we recommend resetting all levels to their highest value (255) after using this
mode.
1.) Select
2.) Choose
3.) Using the <UP>/<DOWN> keys, select the color you wish to display by
varying Red/Green/Blue intensity between 0 and 255, then hit <ENTER> to
confi rm each color choice.
4.) Select Color preset mode as instructed above, then select
<ENTER> to confi rm.
NAnu from the control panel, then hit <ENTER>.
rEd, GrEE, bLuE or Uhit, then hit <ENTER> to confi rm.
CoL 15. then
To Show the Fixture Running Hours:
1.) Select
FhrS from the control panel, then hit <ENTER> to confi rm.
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 8
Troubleshooting
Symptom Solution
Fixture AutoShut Off
Beam is Dim Check optical system and clean excess dust/grime. Also
No Light Output Check to ensure fi xture is operating under correct mode, IE
Chase Speed
Too Fast/Slow
No Power Check fuse, AC cord and circuit for malfunction.
Blown Fuse Check AC cord and circuit for damage, verify that moving
Slow Movement Verify that 220V/110V switch is in the correct position, if
No Response to
Audio
Check the fan in the fi xture. If it is stopped or moving
slower than normal, the unit may have shut itself off due to
high heat. This is to protect the fi xture from overheating.
Clear the fan of obstructions, or return the unit for service.
ensure that the 220V/110V switch is in the correct position,
if applicable.
sound active/auto/DMX/Etc., if applicable. Contact service
for more information.
Check to ensure proper setup of speed adjustment.
parts are not restricted and that unit’s ventilation is not
obstructed
applicable. Also check that speed channels are set appropriately.
Verify that the fi xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.
Fixture Not
Responding /
Responding Erraticly
Intermittant
Lamp
Remote Doesn’t
Work
Fixture Moving
On Its Own
Make sure all connectors are seated properly and securely.
Use Only DMX Cables.
Install a Terminator.
Check all cables for defects.
Reset fi xture(s).
Check lamp for properly installation.
Relamp, lamp may have reached end of life.
Verify remote control cable is installed properly and securely.
Verify remote is correct type (CA-9 or other as applicable.)
Verify proper mode of operation. Is the fi xture in “Auto”
mode?
If your problem isn’t listed, or if problems persist,
please contact support: support@blizzardlighting.com.
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Page 9
5. APPENDIX
Keeping Your Puck™ Q12 As Good As New
The fi xture you’ve received is a rugged, tough piece of pro lighting equip-
ment, and as long as you take care of it, it will take care of you. That said, like
anything, you’ll need to take care of it if you want it to operate as designed.
You should absolutely keep the fi xture clean, especially if you are using it in an
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled
drinks.
Cleaning the optics routinely with a suitable glass cleaner will greatly improve
the quality of light output. Keeping the fans free of dust and debris will keep
the fi xture running cool and prevent damage from overheating.
In transit, keep the fi xtures in cases. You wouldn’t throw a prized guitar,
drumset, or other piece of expensive gear into a gear trailer without a case,
and similarly, you shouldn’t even think about doing it with your shiny new light
fi xtures.
Common sense and taking care of your fi xtures will be the single biggest thing
you can do to keep them running at peak performance and let you worry about
designing a great light show, putting on a great concert, or maximizing your client’s satistfaction and “wow factor.” That’s what it’s all about, after all!
Returns (Gasp!)
We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But, like
any complex piece of equipment designed and built by humans, once in a while,
something doesn’t go as planned. If you fi nd yourself with a fi xture that isn’t
behaving like a good little fi xture should, you’ll need to obtain a Return Authori-
zation (RA).
Don’t worry, this is easy. Just send an email to support@blizzardlighting.com,
and we’ll issue you an RA. Then, you’ll need to send the unit to us using a
trackable, pre-paid freight method. We suggest using USPS Priority or UPS.
Make sure you carefully pack the fi xture for transit, and whenever possible, use
the original box & packing for shipping.
When returning your fi xture for service, be sure to include the following:
1.) Your contact information (Name, Address, Phone Number, Email address).
2.) The RA# issued to you
3.) A brief description of the problem/symptoms.
We will, at our discretion, repair or replace the fi xture. Please remember that
any shipping damage which occurs in transit to us is the customer’s responsibility, so pack it well!
Shipping Issues
Damage incurred in shipping is the responsibility of the shipper, and
must be reported to the carrier immediately upon receipt of the items.
Claims must be made within seven (7) days of receipt.
Page 10
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Tech Specs!
Weight & Dimensions
Length 8.25 inches (210 mm)
Width 3.75 inches (95.25 mm)
Height 7.5 inches (190 mm)
Weight 4.2 lbs (1.9 kg)
Power
Operating Voltage 90-230VAC, 50-60 Hertz
Fuse 3A 250V
Power Consumption 56W
Light Source
LED 12x 10-Watt (4*2.5-watt) Quad-Color RGBA
(Q12A) / RGBW (Q12W) LED’s 60K hrs.
Optical
Beam Angle 25 degrees
29 degree fi eld
Luminous Intensity Puck Q12A: 9,770 Lux @ 1m
Puck Q12W: TBA Lux @ 1m
Thermal
Max. Operating Temp. 104 degrees F (40 degrees C) ambient
Control
Protocol USITT DMX-512
DMX Channels 4 or 7 (User Selectable)
Input 3-pin XLR Male
Output 3-pin XLR Female
Standalone, Master/Slave, Sound Active,
Other Operating Modes
Color Preset, Standalone color mixing
Military Callsign
Tango-Papa-Quebec-One-Two-Alpha (Q12A) or
Tango-Papa-Quebec-One-Two-Whiskey (Q12W)
2-year limited warranty, does not cover mal-
Warranty
function caused by damage to LED’s.
Page 11
The Puck Q12A / Q12W Manual Rev. A Copyright (c) 2011 Blizzard Lighting, LLC
Enjoy your product!
Our sincerest thanks for your purchase!
--The team @ Blizzard Lighting
Loading...