Blizzard Lighting Lo-Pro CSI User Manual

Download

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

Lo-Pro CSI™ 1

1. Getting Started 3

What’s In The Box? 3 Getting It Out Of The Box 3 Powering Up! 3 Getting A Hold Of Us 3 Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The Lo-Pro CSI™ 5

Features 5 DMX Quick Reference 5 The Lo-Pro CSI™ Pin-up Picture 6

3. Setup 7

Fuse Replacement 7 Connecting A Bunch Of Stiletto’s 7 Data/DMX Cables 7 Cable Connectors 8 3-Pin??? 5-Pin??? Huh? 8 Take It To The Next Level: Setting up DMX Control 8 Fixture Linking (Master/Slave Mode) 9 Mounting/Rigging 9

4. Operating Adjustments 10

The Control Panel 10 Control Panel Menu Structure 11 DMX Channel Settings 11 View Fixture Info (Hours, Version#) 11 Dimmer Delay Settings 11 DMX, Auto & Sound Active Modes 11 Manual Settings 11 Troubleshooting 12

5. Appendix 13

A Quick DMX Lesson 13 Keeping Your Lo-Pro CSI™ As Good As New 14 Returns (Gasp!) 14 Shipping Issues 14 Tech Specs 15

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x Lo-Pro CSI™

• An Ever-So-Handy Power Cord

• One really classy DMX cable

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on your purchase of the amazing Lo-Pro CSI™. With a name like Lo-Pro

CSI™, it is denitely worth some investigation! Now that you’ve got your Lo-Pro CSI™

(or hopefully, CSI’s!)

, you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition. If anything looks as if it has been damaged in transit, notify the shipper immediately and keep the packing material for

inspection. Again, please save the carton and all packing materials. If a xture must be returned to the factory, it is important that the xture be returned in the original factory

box and packing.

Powering Up!

All xtures must be powered directly o a switched circuit and cannot be run o a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch.

AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the xture you receive is suitable for your local power supply. See the label on the xture or refer to the xture’s specications chart for more information. A xture’s listed current rating is its average current draw under normal conditions. Check the xture or device

carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch. All xtures

must be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, please just visit our website at www.blizzardlighting. com and open a support ticket. We’ll be happy to help, honest.

Blizzard Lighting N16 W23390 Stoneridge Dr. Ste E Waukesha, WI 53188 USA www.blizzardlighting.com 414-395-8365

Disclaimer: The information and specications contained in this document are subject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time. You can download the latest version of this document from www.blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Henry 2/17/2015 J. Thomas 4/9/2015

Page 4

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the de-

cal or rear panel of the xture.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately. NEVER try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please open a support ticket at www. blizzardlighting.com/tickets.

Page 5

2. MEET THE LO-PRO CSI™

MAIN FEATURES

• 36x high output, 3-watt ~365nm UV LED

• Full on UV intensity + 2 unique pixel patterns

• Variable electronic strobe and dimmer

• Built-in auto programs via master/slave

• Built-in sound active programs

• Standalone, master/slave, auto, sound active modes

• Easy 1/2/3/4/5-channel DMX control

• 15° Beam angle

• Lightweight and Compact (It kept its New Years’ resolution!)

• 4-button LED control panel for easy programming

• Power outlet for xture linking

• Two-piece mounting yoke allows exibility in positioning

DMX Quick Reference (1/2/3/4/5-Channel Modes)

Channel

1.001 2.001 3.001 4.001 5.001

Dimmer UV Intensity Dimmer Dimmer Dimmer

-- UV Intensity UV Intensity Strobe Strobe

-- -- UV Intensity UV Intensity UV Intensity

-- -- -- UV Intensity UV Intensity

-- -- -- -- Color Temp

Page 6

Figure 1: The Lo-Pro CSI™ Pin-Up Picture

36x3w ~365nm UV LEDs

Figure 2: The Rear Connections

PowerCon™ Compatible In/Out

LED Display

Touring-

grade

compact

shell

Two-piece

mounting

yoke

4-button Control Panel

Safety Cable Attachment Holes

DMX 3-pin In/Out

Tightening

Knob

Page 7

3. SETUP

Fuse Replacement

CAUTION! The Lo-Pro Flux™ utilizes a high-output switch-mode power supply with an internal fuse. Under normal operating conditions, the fuse

should not require replacement. The fuse is eld replaceable, however it is an advanced procedure suited to qualied individuals. Should your Lo-

Pro Flux™ fuse require replacement, please contact Blizzard Lighting for instructions, or to return your unit for service.

Connecting A Bunch of Lo-Pro Flux™ Fixtures

You will need a serial data link to run light shows using a DMX-512

controller or to run shows on two or more xtures set to sync in master/

slave operating mode. The combined number of channels required by all

the xtures on a serial data link determines the number of xtures the

data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also, connecting more than 32 xtures on one serial data link without the

use of a DMX optically-isolated splitter may result in deterioration of the digital DMX signal. The maximum recommended cable-run distance is 500

meters (1640 ft). The maximum recommended number of xtures on a serial data link is 32 xtures.

Data/DMX Cabling

To link xtures together you’ll need data cables. You should use data-

grade cables that can carry a high quality signal and are less prone to electromagnetic interference.

For instance, Belden© 9841 meets the specications for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but note that they cannot transmit DMX data as reliably over long distances. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft. Maximum capacitance between conductor & shield – 55 pF/ft. Maximum resistance of 20 ohms / 1000 ft. Nominal impedance 100 – 140 ohms

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the x- ture’s chassis ground. Grounding the common can cause a ground

loop, and your xture may perform erratically. Test cables with an

ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. They are widely available over the internet and from specialty retailers If you’d like to build your own, the chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male (Input)

Ground/Shield Pin 1 Pin 1

DMX Data (-) Pin 2 Pin 2

DMX Data (+) Pin 3 Pin 3

Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output) on the controller.

Step 2: Connect the female connector of the DMX cable to the rst xture’s male connector (input). Note: It doesn’t matter which

xture address is the rst one connected. We recommend connecting the xtures in

terms of their proximity to the controller,

rather than connecting the lowest xture number rst, and so on.

Step 3: Connect other xtures in the chain

from output to input as above. Place a DMX

terminator on the output of the nal xture

to ensure best communication.

Page 9

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of

the rst xture.

2. Connect the end of the cable coming from the

rst xture which will have a (female) 3 pin connector to the input connector of the next xture con-

sisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the

input of the following xture and so on.

A quick note: Often, the setup for MasterSlave and Standalone operation requires that

the rst xture in the

chain be initialized for this purpose via either settings in the control panel or DIP-switches.

Secondarily, the xtures

that follow may also require a slave setting.

Check the “Operating Adjustments” section in this manual for com-

plete instructions for this type of setup and conguration.

Mounting & Rigging

This xture may be mounted in any SAFE position provided there is

enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the

xture using a suitable “C” or “O” type clamp. The clamp should be rated to hold at least 10x the xture’s weight to ensure structural sta-

bility. Do not mount to surfaces with unknown strength, and ensure

properly “rated” rigging is used when mounting xtures overhead.

Adjust the angle of the xture by loosening both knobs and tilting the xture. After nding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the xture will be exposed to rain,

high humidity, extreme temperature changes or restricted ventilation.

Page 10

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and dierent modes possible with the Lo-Pro CSI™ are accessed by using the control panel on the front of the xture. There

are 4 control buttons below the LED display which allow you to navigate through the various control panel menus.

Button Function

<MENU>

<UP>

<DOWN>

<ENTER>

Used to access the menu or to return to a previous menu option.

Scrolls through menu options in ascending order.

Scrolls through menu options in descending order.

Used to select and store the current menu or option within a menu.

Access control panel functions using the four panel buttons located directly underneath the LED Display.

The Control Panel LED Display shows the menu items you select from the menu map on page #11. When a menu function is selected, the

display will show immediately the rst available option for the selected

menu function. To select a menu item, press <ENTER>.

Use the <UP> and <DOWN> buttons to navigate the menu map and menu options. Press the <ENTER> button to access the menu function currently displayed or to enable a menu option. To return to the previous option or menu without changing the value, press the <MENU> button.

Page 11

Control Panel Menu Structure

Main Menu Mode Value Function

Addr

001-512 DMX Address

CH--

1.001

-- 1-Channel Mode

2.001

-- 2-Channel Mode

3.001

-- 3-Channel Mode

4.001

-- 4-Channel Mode

5.001

-- 5-Channel Mode

uL--

001-100 Section 1 UV Intensity

EL--

001-100 Section 2 UV Intensity

FLAS

001-100 Strobe Speed (Slow <--> Fast)

FAdE

001-100 Fade In & Out (Slow <--> Fast)

ASC-

001-100 Speed

AuTo

0-49 Built-In Programs

Sond

50-100 Sound

dEL0

-- Dimmer Delay O

dEL1

-- Dimmer Delay 25%

dEL2

-- Dimmer Delay 50%

dEL3

-- Dimmer Delay 75%

DMX Channel Values In-Depth

1.001 2.001 3.001 4.001 5.001

Channel Value

What it does

1 -- 1 1 1

000 <-> 255

Dimmer

-- -- -- 2 2

000 <-> 255

Strobe

-- 1 2 3 3

000 <-> 255

Section 1 UV Intensity

-- 2 3 4 4

000 <-> 255

Section 2 UV Intensity

-- -- -- -- 5

000 <-> 255

Color Temperature

Page 12

Troubleshooting

Symptom Solution

Fixture Auto-

Shut O

Check the fan in the xture. If it is stopped or moving slower than normal, the unit may have shut itself o due to high heat. This is to protect the xture from overheating.

Clear the fan of obstructions, or return the unit for service.

Zoom is Dim Check optical system and clean excess dust/grime. Also

ensure that the 220V/110V switch is in the correct position, if applicable.

No Light Output Check to ensure xture is operating under correct mode, IE

sound active/auto/DMX/Etc., if applicable. Contact service for more information.

Chase Speed Too Fast/Slow

Check to ensure proper setup of speed adjustment.

No Power Check fuse, AC cord and circuit for malfunction.

Blown Fuse Check AC cord and circuit for damage, verify that moving

parts are not restricted and that unit’s ventilation is not obstructed

Slow Movement Verify that 220V/110V switch is in the correct position, if

applicable. Also check that speed channels are set appropriately.

No Response to Audio

Verify that the xture is in “Sound Active” mode. Adjust Audio Sensitivity, If Applicable.

Fixture Not Responding / Responding Erratically

Make sure all connectors are seated properly and securely. Use Only DMX Cables. Install a Terminator. Check all cables for defects.

Reset xture(s).

Intermittent Lamp

Check lamp for properly installation. Relamp, lamp may have reached end of life.

Fixture Moving On Its Own

Verify proper mode of operation. Is the xture in “Auto”

mode?

If your problem isn’t listed, or if problems persist,

please open a support ticket at www.blizzardlighting.com/tickets.

Page 13

5. APPENDIX

A Quick Lesson On DMX

DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre Technology (USITT) as a standardized method for connecting lighting consoles to lighting

dimmer modules. It was revised in 1990 and again in 2000 to allow more exibility. The

Entertainment Services and Technology Association (ESTA) has since assumed control over the DMX512 standard. It has also been approved and recognized for ANSI standard clas-

sication.

DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common communications standard used by lighting and related stage equipment.

DMX provides up to 512 control “channels” per data link. Each of these channels was originally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an 8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb

being completely o while 255 corresponds to the light bulb being fully on.

DMX data is transmitted at 250,000 bits per second using the RS-485 transmission standard over two wires. As with microphone cables, a grounded cable shield is used to prevent interference with other signals.

There are ve pins on a DMX connector: a wire for ground (cable shield), two wires for

“Primary” communication which goes from a DMX source to a DMX receiver, and two wires for a “Secondary” communication which goes from a DMX receiver back to a DMX source. Generally, the “Secondary” channel is not used so data ows only from sources to receivers. Hence, most of us are most familiar with DMX-512 as being employer over typical

3-pin “mic cables,” although this does not conform to the dened standard.

DMX is connected using a daisy-chain conguration where the source connects to the input of the rst device, the output of the rst device connects to the input of the next device,

and so on. The standard allows for up to 32 devices on a single DMX link.

Each receiving device typically has a means for setting the “starting channel number” that

it will respond to. For example, if two 6-channel xtures are used, the rst xture might

be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next

xture would be set to start at channel 7 so it would respond to channels 7 through 12.

The greatest strength of the DMX communications protocol is that it is very simple and robust. It involves transmitting a reset condition (indicating the start of a new “packet”), a start code, and up to 512 bytes of data. Data packets are transmitted continuously. As

soon as one packet is nished, another can begin with no delay if desired (usually another

follows within 1 ms). If nothing is changing (i.e. no lamp levels change) the same data will be sent out over and over again. This is a great feature of DMX -- if for some reason the

data is not interpreted the rst time around, it will be re-sent shortly.

Not all 512 channels need to be output per packet, and in fact, it is very uncommon to nd

all 512 used. The fewer channels are used, the higher the “refresh” rate. It is possible to get DMX refreshes at around 1000 times per second if only 24 channels are being transmitted. If all 512 channels are being transmitted, the refresh rate is around 44 times per second.

In summary, since its design and evolution in the 1980’s DMX has become the standard

for lighting control. It is exible, robust, and scalable, and its ability to control everything

from dimmer packs to moving lights to foggers to lasers makes it an indispensable tool for any lighting designer or lighting performer.

Page 14

Keeping Your Lo-Pro CSI™ As Good As New

The xture you’ve received is a rugged, tough piece of pro lighting equipment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed.

You should absolutely keep the xture clean, especially if you are using it in an

environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve the quality of light output. Keeping the fans free of dust and debris will keep

the xture running cool and prevent damage from overheating.

In transit, keep the xtures in cases. You wouldn’t throw a prized guitar,

drumset, or other piece of expensive gear into a gear trailer without a case, and similarly, you shouldn’t even think about doing it with your shiny new light

xtures.

Common sense and taking care of your xtures will be the single biggest thing

you can do to keep them running at peak performance and let you worry about designing a great light show, putting on a great concert, or maximizing your client’s satisfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry about sending a defective unit back, or sending a unit in for service. But, like any complex piece of equipment designed and built by humans, once in a while,

something doesn’t go as planned. If you nd yourself with a xture that isn’t behaving like a good little xture should, you’ll need to obtain a Return Authori-

zation (RA).

Don’t worry, this is easy. Just go to our website and open a support ticket at www.blizzardlighting.com/tickets, and we’ll issue you an RA. Then, you’ll need to send the unit to us using a trackable, pre-paid freight method. We suggest

using USPS Priority or UPS. Make sure you carefully pack the xture for transit,

and whenever possible, use the original box & packing for shipping.

When returning your xture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the xture. Please remember that

any shipping damage which occurs in transit to us is the customer’s responsibility, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and must be reported to the carrier immediately upon receipt of the items. Claims must be made within seven (7) days of receipt.

Page 15

Tech Specs!

Weight & Dimensions

Width 9 inches (22.7 cm) Depth 4.75 inches (12 cm) Height 11.5 inches (29.2 cm) Weight 7.6lbs (3.45 kg)

Power

Operating Voltage 90-250VAC 50/60Hz Power Consump-

tion

34W, .52A, PF:.62

Light Source

LED 36 x 3W ~365nm UV LED

Optical

Beam Angle 15°

Thermal

Max. Operating Temp.

104 degrees F (40 degrees C) ambient

Control

Protocol USITT DMX-512 DMX Channels 1/2/3/4/5 channels Input 3-pin XLR Male Output 3-pin XLR Female

Other Information

Age is something that doesn’t matter, unless you are a cheese.

Warranty

2-year limited warranty, does not cover malfunction caused by damage to LED’s.

DISCLAIMER:

The power connector tted to the xture and xture cord are designed for compatibility

with products manufactured by Neutrik AG, Neutrik USA and their related entities, how-

ever they are not manufactured by, aliated with or endorsed by Neutrik AG, Neutrik

USA, or any related entity. Neutrik® and powerCON® are registered trademarks of Neutrik AG.

Enjoy your product!

Our sincerest thanks for your purchase!

--The team @ Blizzard Lighting

Blizzard Lighting Lo-Pro CSI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual