Blizzard Lighting BladeRunner White User Manual

TM
white
Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA Copyright (c) 2014
BladeRunner™ White Moving Head Fixture 1
1. Getting Started 3
What’s In The Box? 3 Getting It Out Of The Box 3 Powering Up! 3 Getting A Hold Of Us 3 Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The BladeRunner™ White 5
Main Features 5 Control 5 DMX Quick Reference 5 The BladeRunner™ White Pin-up Picture 7
3. Setup 8
Fuse Replacement 8 Connecting A Bunch Of BladeRunner™ White Fixtures 8 Data/DMX Cables 8 Cable Connectors 9 3-Pin??? 5-Pin??? Huh? 9 Take It To The Next Level: Setting up DMX Control 9 Fixture Linking (Master/Slave Mode) 10 Mounting/Rigging 10
4. Operating Adjustments 11
Navigating The Control Panel 11 Control Panel Menu Structure 11 DMX Mode 12 Set The DMX Starting Address 12 DMX Mode Selection 12 Slave Mode 12 Stand-Alone, Master/Slave, Sound Active Modes 12 PRO-Movement 12 Speed Settings 12 Auto Mode 12 Sound Active Mode 12 Manual Color Adjustments 13 Program Mode 13 LCD Display 13 Version 13 Reset 13 DMX Channel Values In-Depth 14
5. Appendix 15
A Quick DMX Lesson 15 Troubleshooting 15 Keeping Your BladeRunner™ White As Good As New 16 Returns (Gasp!) 16 Shipping Issues 16 Tech Specs 17 Dimensional Drawings 18
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 2
1. GETTING STARTED
What’s In The Box?
• 1 x BladeRunner™ Moving Head Fixture
• 2 x 1/4 Turn Mounting Brackets
• 1 x Stand Mounting Bracket
• An Ever-So-Handy Power Cord
• This Lovely User Manual
Getting It Out Of The Box
Congratulations! You have just purchased a totally unique, stunning quad white beam
moving head xture that’s guaranteed to turn heads anywhere it goes (and tilt them too)!
So now that you’re the proud owner of a BladeRunner™ (or hopefully, BLADERUNNERS!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition. If anything looks as if it has been damaged in transit, notify the shipper immediately and keep the packing material for inspection. Again, please save
the carton and all packing materials. If a xture must be returned to the factory, it is important that the xture be returned in the original factory box and packing.
Powering Up!
All xtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the xture you receive is suitable for your local power supply. See the label on the xture or refer to the xture’s specications chart for more information. A xture’s listed current rating is its average current draw under normal conditions. Check the xture or device
carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your xture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch. All xtures must
be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email. We’ll be happy to help, honest.
Blizzard Lighting N16 W23390 Stoneridge Dr. Ste E Waukesha, WI 53118 USA www.blizzardlighting.com 414-395-8365 Email: support@blizzardlighting.com
Disclaimer: The information and specications contained in this document are subject
to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time. You can download the latest version of this document from www. blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Thomas 4/4/2014 J. Thomas 4/17/2014
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 3
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the
decal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
cord. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately. NEVER try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact Blizzard Lighting at support@blizzardlighting.com.
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 4
2. MEET THE BLADERUNNER™ WHITE
MAIN FEATURES:
• 4x moving heads, each with 1x CREE® 10w White LED
• Blazing fast 540° pan and 270° tilt
• User selectable 9 or 19 DMX channels
• Narrow 2 degree beam angle
• Outstanding quad beam effects
• Built-in sound active programs
• Built-in automated programs via master/slave
• Built-in sound activated programs via master/slave
• 3-pin male input and 3-pin female output
• PowerCon™ compatible AC power In/Out connectors
CONTROL:
• USITT DMX-512 (9/19 Channels)
• 3-pin Input/Output
• 4-button menu with LCD display
DMX Quick Reference (9-Channel Mode)
Channel What is does
1 Dimmer (0% <--> 100%)
2 Strobe (slow <--> fast)
3 Built-in Programs + Sound Active
4 Program Speed (slow <--> fast)
5 Pan
6 Tilt
7 Pan Speed (fast <--> slow)
8 Tilt Speed (fast <--> slow)
9 Motor Reset (246-255)
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 5
DMX Quick Reference (19-Channel Mode)
Channel What is does
1 Dimmer (0% <--> 100%)
2 Strobe (slow <--> fast)
3 1st Head White Intensity (0% <--> 100%)
4 2nd Head White Intensity (0% <--> 100%)
5 3rd Head White Intensity (0% <--> 100%)
6 4th Head White Intensity (0% <--> 100%)
7 Built-in Programs + Sound Active
8 Program Speed (slow <--> fast)
9 1st Head Pan Motor
10 1st Head Tilt Motor
11 2nd Head Pan Motor
12 2nd Head Tilt Motor
13 3rd Head Pan Motor
14 3rd Head Tilt Motor
15 4th Head Pan Motor
16 4th Head Tilt Motor
17 Pan Speed (fast <--> slow)
18 Tilt Speed (fast <--> slow)
19 Motor Reset (246-255)
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 6
Figure 1: The BladeRunner™ White Pin-Up Picture
4x Mini Moving Heads,
each tted with 1x CREE®
High Output White
10-watt LED.
LED
Control
Panel
Bracket
Rubber
Feet
Mounting Holes
Stand
Mounting
Bracket
Figure 2: The Rear Connections
Power Switch
DMX In
Bracket
Mounting Holes
DMX Out
Rubber
Feet
Power In Power Out
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 7
3. SETUP
Fuse Replacement
CAUTION! The BladeRunner™ White utilizes a high-output switch-
mode power supply with an internal fuse. Under normal operating
conditions, the fuse should not require replacement. The fuse is eld replaceable, however it is an advanced procedure suited to qualied
individuals. Should your BladeRunner™ White fuse require replacement, please contact Blizzard Lighting for instructions, or to return your unit for service.
Connecting A Bunch of BladeRunner™ White Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in master/
slave operating mode. The combined number of channels required by all
the xtures on a serial data link determines the number of xtures the
data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without the
use of a DMX optically-isolated splitter may result in deterioration of the digital DMX signal. The maximum recommended cable-run distance is 500 meters (1640 ft).
The maximum recommended number of xtures on a serial data link is 32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but note that they cannot transmit DMX data as reliably over long distances. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft. Maximum capacitance between conductor & shield – 55 pF/ft. Maximum resistance of 20 ohms / 1000 ft. Nominal impedance 100 – 140 ohms
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 8
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the
xture’s chassis ground. Grounding the common can cause a ground loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. They are widely available over the internet and from specialty retailers. If you’d like to build your own, the chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male (Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output) on the controller.
Step 2: Connect the female connector of
the DMX cable to the rst xture’s male
connector (input). Note: It doesn’t matter
which xture address is the rst one
connected. We recommend connecting the
xtures in terms of their proximity to the
controller, rather than connecting the lowest
xture number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 9
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the DMX cable to the output
(female) 3 pin connector of the rst xture.
2. Connect the end of the cable coming from the rst xture which will have a (female) 3 pin connector to the input connector of the next xture consisting of
a (male) 3 pin connector. Then, proceed to connect from the output as stated
above to the input of the following xture and so on.
A quick note: Often, the setup for Master-Slave and Standalone operation
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is enough
room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the xture
using a suitable “C” or “O” type clamp. The clamp should be rated to hold at
least 10x the xture’s weight to ensure structural stability. Do not mount to
surfaces with unknown strength, and ensure properly “rated” rigging is used
when mounting xtures overhead.
Adjust the angle of the xture by loosening both knobs and tilting the xture. After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp replacement access (if applicable) and routine maintenance.
requires that the rst xture in the
chain be initialized for this purpose via either settings in the control panel or DIP-switches. Secondarily,
the xtures that follow may also
require a slave setting.
Check the “Operating Adjustments” section in this manual for complete instructions for this type of setup and
conguration.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
Lighting Stand Mounting
This xture comes with an easy to use stand mounting bracket. Please make
sure the lighting stand you use is rated to safely hold the weight of this unit and do not over-extend the lighting stand. For the safety of yourself, your audience,
and the xture... always take advantage of the use of the stand’s safety pins!
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 10
4. OPERATING ADJUSTMENTS
The Control Panel
All the goodies and different modes possible with the BladeRunner™ White are accessed by
using the control panel on the front of the xture. There are 4 control buttons below the
LCD display which allow you to navigate through the various control panel menus.
MENU ENTERDOWNUP
Main Menu
To navigate through the LCD control panel main menu, use the <MENU> button to scroll through the various top level menu options. Then to scroll through sub-menu options, use the <UP/DOWN> buttons. Push the <ENTER> button to save any changes made.
Control Panel Menu Structure
Address 001-512 DMX Address CHND 9CH 9 Channel DMX Mode 19CH 19 Channel DMX Mode AUTO STOP/RUN Auto Mode (slower color changing) AUTO 1 STOP/RUN Auto Mode (faster color changing) AUDIO STOP/RUN Sound Active Mode
COLOR White 1 Head 1 - White (0-255) White 2 Head 2 - White (0-255) White 3 Head 3 - White (0-255) White 4 Head 4 - White (0-255) Shut Strobe Rate (0-255)
PROGRAM 01-10 Built-in Programs PRO-Movement ON/OFF Auto Movement On/Off SPEED <ENTER> Speed Settings Movement Movement Speed (001-255) Color Color Speed (001-255) LED ON/OFF LCD Backlight On/Off VERSION V1.0.0 Firmware Version RESET Yes? Fixture Reset
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 11
DMX Mode
Allows the unit to be controlled by any universal DMX controller.
Set The DMX Starting Address
To assign a DMX staring address to the xture, use the <MENU> button to scroll to Address,
then use the <UP/DOWN> buttons to display any value within the range of 001-512. Then
push the <ENTER> button to conrm your choice.
DMX Mode Selection
To use the xture in either of its two DMX channel mode congurations, use the <MENU>
button to scroll to CHND, then use the <UP/DOWN> buttons to display either 9CH or 19CH.
Then push the <ENTER> button to conrm your choice.
Slave Mode
1.) Disconnect xture(s) from any DMX signal source.
2.) Set each xture to matching DMX modes (9CH or 19CH).
3.) Connect all xtures together via DMX. The rst xture in the DMX chain will be the master
xture, followed by the slave xtures.
4.) Connect DMX controller to the master unit for DMX control.
Stand-Alone, Master/Slave, Sound Active Modes:
Allows a single or Master/Slaved units to run factory installed programs at user selectable speeds.
PRO-Movement
This allows you to enable/disable auto movement of the heads in Program Mode or within Manual Color Adjustments. This will not effect movement in Auto or DMX modes.
1.) Use the <MENU> button to scroll to PRO-Movement, then use the <UP/DOWN> buttons
to display either ON or OFF. Then push the <ENTER> button to conrm your choice.
Speed Settings
This allows you to adjust the speed of the moving heads and color macros in Program Mode, Auto Mode or within Manual Color Adjustments. This will not effect speed in DMX mode.
1.) Use the <MENU> button to scroll to SPEED, then use the <UP/DOWN> buttons to display
either Movement or Color, then push the <ENTER> button. You can now adjust the speed
settings from 001-255 (slow <--> fast).
Auto Mode
To run the xture in auto mode, use the <MENU> button to scroll to AUTO or AUTO 1, then
push the <ENTER> button to conrm. You then adjust the movement and macro speed settings
of the auto mode program (see Speed Settings).
Sound Active Mode
To run the xture in sound active mode, use the <MENU> button to scroll to AUDIO, then push
the <ENTER> button to conrm.
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 12
Manual Color Adjustments
Allows the user to adjust the intensity level of each individual moving head xture. You can set your own
intensity levels and then add PRO-Movement if you like! (See p. 12).
1.) Use the <MENU> button to scroll to COLOR, then use the <UP/DOWN> buttons to
display the White intensity levels for xtures 1, 2, 3, and 4. Push the <ENTER> button while
highlighting any to display the color intensity range settings from 000-255. Use the <UP/
DOWN> buttons to adjust the intensity, then push <ENTER> to conrm your choice.
2.) The last option in the COLOR submenu is Shut (strobe). Using the same steps as above,
you can adjust the strobe rate values from 000-255 (slow <--> fast).
Program Mode
Allows a single unit to display a variety of built-in programs without a DMX controller.
1.) Use the <MENU> button to scroll to PROGRAM, then use the <UP/DOWN> buttons to
display the built-in program number from 01-10. Push the <ENTER> to conrm your choice. If
you wish, you can then also enable/disable PRO-Movement, or adjust the Speed Settings of the
Movement or Color Macros. (See p. 12)
LCD Display
To turn on/off the backlit LCD display, use the <MENU> button to scroll to LED, then push
<ENTER>. Then use the <UP/DOWN> buttons to scroll or either ON or OFF, and push
<ENTER> button to conrm your choice. ON will leave the display illuminated constantly, and
OFF will turn the display off after 40 seconds of idle.
Version
This menu option simply displays the xtures installed rmware version number.
Reset
To automatically reset the motors to realign the moving head positions, use the <MENU>
button to scroll to RESET, then push <ENTER>.
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 13
DMX Values In-Depth (9-Channel Mode)
Channel Value What It Does
1 000 <--> 255 Dimmer (0% <--> 100%)
2 000 <--> 255 Strobe (Slow <--> Fast)
3
4 000 <--> 255 Macro Speed (0% <--> 100%)
5 000 <--> 255 Pan
6 000 <--> 255 Tilt
7 000 <--> 255 Pan Speed (fast <--> slow)
8 000 <--> 255 Tilt Speed (fast <--> slow)
9 000 <--> 245
000 <--> 250 251 <--> 255
246 <--> 255
Built-In Programs + Sound Active
Macro Functions Sound Active Mode
No Function Reset Motors
DMX Values In-Depth (19-Channel Mode)
Channel Value What It Does
1 000 <--> 255 Dimmer (0% <--> 100%)
2 000 <--> 255 Strobe (Slow <--> Fast)
3 000 <--> 255 1st Head - White Intensity (0% <--> 100%)
4 000 <--> 255 2nd Head - White Intensity (0% <--> 100%)
5 000 <--> 255 3rd Head - White Intensity (0% <--> 100%)
6 000 <--> 255 4th Head - White Intensity (0% <--> 100%)
7
8 000 <--> 255 Macro Speed (0% <--> 100%)
9 000 <--> 255 1st Head - Pan
10 000 <--> 255 1st Head - Tilt
11 000 <--> 255 2nd Head - Pan
12 000 <--> 255 2nd Head - Tilt
13 000 <--> 255 3rd Head - Pan
14 000 <--> 255 3rd Head - Tilt
15 000 <--> 255 4th Head - Pan
16 000 <--> 255 4th Head - Tilt
17 000 <--> 255 Pan Speed (fast <--> slow)
18 000 <--> 255 Tilt Speed (fast <--> slow)
19 000 <--> 245
000 <--> 250 251 <--> 255
246 <--> 255
Built-In Programs + Sound Active
Macro Functions Sound Active Mode
No Function Reset Motors
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 14
5. APPENDIX
A Quick Lesson On DMX
DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common communications standard used by lighting and related stage equipment.
DMX provides up to 512 control “channels” per data link. Each of these channels was originally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an 8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb being completely off while 255 corresponds to the light bulb being fully on.
DMX data is transmitted at 250,000 bits per second using the RS-485 transmission standard over two wires. As with microphone cables, a grounded cable shield is used to prevent interference with other signals.
There are ve pins on a DMX connector: a wire for ground (cable shield), two wires for
“Primary” communication which goes from a DMX source to a DMX receiver, and two wires for a “Secondary” communication which goes from a DMX receiver back to a DMX
source. Generally, the “Secondary” channel is not used so data ows only from sources
to receivers. Hence, most of us are most familiar with DMX-512 as being employer over
typical 3-pin “mic cables,” although this does not conform to the dened standard.
DMX is connected using a daisy-chain conguration where the source connects to the input of the rst device, the output of the rst device connects to the input of the next device,
and so on. The standard allows for up to 32 devices on a single DMX link.
Each receiving device typically has a means for setting the “starting channel number” that
it will respond to. For example, if two 6-channel xtures are used, the rst xture might
be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next
xture would be set to start at channel 7 so it would respond to channels 7 through 12.
Troubleshooting
Symptom Solution
Fixture Auto­Shut Off
Beam is Dim Check optical system and clean excess dust/grime. Also ensure that
No Light Output Check to ensure xture is operating under correct mode, IE sound
Chase Speed Too Fast/Slow
No Power Check fuse, AC cord and circuit for malfunction.
No Response to Audio
Fixture Not Responding / Responding Er­ratically
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Check the fan in the xture. If it is stopped or moving slower than
normal, the unit may have shut itself off due to high heat. This is to
protect the xture from overheating. Clear the fan of obstructions,
or return the unit for service.
the 220V/110V switch is in the correct position, if applicable.
active/auto/DMX/Etc., if applicable. Contact service for more infor­mation.
Check to ensure proper setup of speed adjustment.
Verify that the xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.
Make sure all connectors are seated properly and securely. Use Only DMX Cables. Install a Terminator. Check all cables for defects.
Reset xture(s).
Page 15
Keeping Your BladeRunner™ White As Good As New
The xture you’ve received is a rugged, tough piece of pro lighting equipment,
and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed.
You should absolutely keep the xture clean, especially if you are using it in an
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.
Cleaning the optics routinely with a suitable glass cleaner will greatly improve the quality of light output. Keeping the fans free of dust and debris will keep
the xture running cool and prevent damage from overheating.
In transit, keep the xtures in cases. You wouldn’t throw a prized guitar,
drumset, or other piece of expensive gear into a gear trailer without a case, and similarly, you shouldn’t even think about doing it with your shiny new light
xtures.
Common sense and taking care of your xtures will be the single biggest thing
you can do to keep them running at peak performance and let you worry about designing a great light show, putting on a great concert, or maximizing your client’s satisfaction and “wow factor.” That’s what it’s all about, after all!
Returns (Gasp!)
We’ve taken a lot of precautions to make sure you never even have to worry about sending a defective unit back, or sending a unit in for service. But, like any complex piece of equipment designed and built by humans, once in a
while, something doesn’t go as planned. If you nd yourself with a xture that isn’t behaving like a good little xture should, you’ll need to obtain a Return
Authorization (RA).
Don’t worry, this is easy. Just send an email to support@blizzardlighting.com, and we’ll issue you an RA. Then, you’ll need to send the unit to us using a trackable, pre-paid freight method. We suggest using USPS Priority or UPS.
Make sure you carefully pack the xture for transit, and whenever possible, use
the original box & packing for shipping.
When returning your xture for service, be sure to include the following:
1.) Your contact information (Name, Address, Phone Number, Email address).
2.) The RA# issued to you
3.) A brief description of the problem/symptoms.
We will, at our discretion, repair or replace the xture. Please remember
that any shipping damage which occurs in transit to us is the customer’s responsibility, so pack it well!
Shipping Issues
Damage incurred in shipping is the responsibility of the shipper, and must be reported to the carrier immediately upon receipt of the items. Claims must be made within seven (7) days of receipt.
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 16
Tech Specs!
Weight & Dimensions
Length 40.5 inches (102.9 cm)
Height 8.25 inches (21 cm)
Depth Base: 3.27” (8.3 cm), Head: 5” (12.7 cm)
Weight 22.1 lbs (10 kg)
Power
Operating Voltage AC 110-240VAC, 50-60 Hertz
Power Consumption 77w, 1.13A
Power Factor .6
Light Source
LED 4* 10-watt White CREE® LEDs
Luminous Intensity 96,000 Lux @1m, 24,730 Lux @ 2m
Optical
Beam Angle 2 degree
Thermal
Max. Operating
104 degrees F (40 degrees C) ambient
Temp.
Control
Protocol USITT DMX-512
DMX Channels 9 or 19 Channels
Input 3-pin XLR Male
Output 3-pin XLR Female
Other Operating Modes Standalone, Master/Slave, Auto, Sound Active
Other Information
Every ght is a food ght when you’re a cannibal.
2-year limited warranty, does not cover mal-
Warranty
DISCLAIMER:
The power connector tted to the xture and xture cord are designed for compatibility
with products manufactured by Neutrik AG, Neutrik USA and their related entities, how-
ever they are not manufactured by, afliated with or endorsed by Neutrik AG, Neutrik
USA, or any related entity. Neutrik® and powerCON® are registered trademarks of Neutrik AG.
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
function caused by damage to LED’s.
Page 17
Dimensional Drawings
8.25 in
3.27 in
3.27 in
40.5 in
4.8 in
5 in
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 18
This page intentionally left blank.
BladeRunner™ White User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Page 19
Enjoy your product!
Our sincerest thanks for your purchase!
--The team @ Blizzard Lighting
Loading...