Blizzard Lighting BladeRunner RGBW User Manual

Download

rgbw

Blizzard Lighting, LLC

www.blizzardlighting.com

TABLE OF CONTENTS

BladeRunner™ RGBW Moving Head Fixture 1

1. Getting Started 3

What’s In The Box? 3 Getting It Out Of The Box 3 Powering Up! 3 Getting A Hold Of Us 3 Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The BladeRunner™ RGBW 5

Main Features 5 Control 5 DMX Quick Reference 5 The BladeRunner™ RGBW Pin-up Picture 7

3. Setup 8

Fuse Replacement 8 Connecting A Bunch Of BladeRunner™ RGBW Fixtures 8 Data/DMX Cables 8 Cable Connectors 9 3-Pin??? 5-Pin??? Huh? 9 Take It To The Next Level: Setting up DMX Control 9 Fixture Linking (Master/Slave Mode) 10 Mounting/Rigging 10 Lighting Stand Mounting 10

4. Operating Adjustments 11

Navigating The Control Panel 11 Control Panel Menu Structure 11 DMX Mode 12 Set The DMX Starting Address 12 DMX Mode Selection 12 Slave Mode 12 Stand-Alone, Master/Slave, Sound Active Modes 12 PRO-Movement 12 Speed Settings 12 Auto Mode 12 Sound Active Mode 12 Manual Color Adjustments 13 Program Mode 13 LCD Display 13 Version 13 Reset 13 DMX Channel Values In-Depth 14

5. Appendix 16

A Quick DMX Lesson 16 Troubleshooting 16 Keeping Your BladeRunner™ RGBW As Good As New 17 Returns (Gasp!) 17 Shipping Issues 17 Tech Specs 18 Dimensional Drawings 19

Page 2

1. GETTING STARTED

What’s In The Box?

• 1 x BladeRunner™ Moving Head Fixture

• 2 x Omega 1/4 Turn Mounting Brackets

• 1 x Stand Mounting Bracket

• An Ever-So-Handy Power Cord

• This Lovely User Manual

Getting It Out Of The Box

Congratulations! You have just purchased a totally unique, stunning quad-beam RGBW

moving head xture that’s guaranteed to turn heads anywhere it goes (and tilt them too)!

So now that you’re the proud owner of a BladeRunner™ (or hopefully, BLADERUNNERS!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition. If anything looks as if it has been damaged in transit, notify the shipper immediately and keep the packing material for inspection. Again, please save

the carton and all packing materials. If a xture must be returned to the factory, it is important that the xture be returned in the original factory box and packing.

Powering Up!

All xtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch.

AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the xture you receive is suitable for your local power supply. See the label on the xture or refer to the xture’s specications chart for more information. A xture’s listed current rating is its average current draw under normal conditions. Check the xture or device

carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch. All xtures must

be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, just give us a call or send an email. We’ll be happy to help, honest.

Blizzard Lighting N16 W23390 Stoneridge Dr. Ste E Waukesha, WI 53118 USA www.blizzardlighting.com 414-395-8365 Email: support@blizzardlighting.com

Disclaimer: The information and specications contained in this document are subject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time. You can download the latest version of this document from www. blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Thomas 4/4/2014 J. Thomas 4/17/2014

Page 3

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the

decal or rear panel of the xture.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

cord. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately. NEVER try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact Blizzard Lighting at support@blizzardlighting.com.

Page 4

2. MEET THE BLADERUNNER™ RGBW

MAIN FEATURES:

• 4x moving heads, each with 1x CREE® 10w R/G/B/W 4-in-1 LED

• Blazing fast 540° pan and 240° tilt

• User selectable 14 or 32 DMX channels

• Full RGBW color in standalone & DMX mode

• Narrow 2 degree beam angle

• Outstanding quad beam effects

• Built-in sound active programs

• Built-in automated programs via master/slave

• Built-in sound activated programs via master/slave

• 3-pin male input and 3-pin female output

• PowerCon™ compatible AC power In/Out connectors

CONTROL:

• USITT DMX-512 (14/32 Channels)

• 3-pin Input/Output

• 4-button menu with LCD display

DMX Quick Reference (14-Channel Mode)

Channel What is does

1 Dimmer (0% <--> 100%)

2 Strobe (slow <--> fast)

3 Red Intensity (0% <--> 100%)

4 Green Intensity (0% <--> 100%)

5 Blue Intensity (0% <--> 100%)

6 White Intensity (0% <--> 100%)

7 Static Colors + Color Snap/Fade

8 Built-in Programs + Sound Active

9 Built-in Program Speed (slow <--> fast)

10 Global Pan

11 Global Tilt

12 Pan Speed (fast <--> slow)

13 Tilt Speed (fast <--> slow)

14 Motor Reset (246-255)

Page 5

DMX Quick Reference (32-Channel Mode)

Channel What is does

1 Dimmer (0% <--> 100%)

2 Strobe (slow <--> fast)

3 1st Head Red Intensity (0% <--> 100%)

4 1st Head Green Intensity (0% <--> 100%)

5 1st Head Blue Intensity (0% <--> 100%)

6 1st Head White Intensity (0% <--> 100%)

7 2nd Head Red Intensity (0% <--> 100%)

8 2nd Head Green Intensity (0% <--> 100%)

9 2nd Head Blue Intensity (0% <--> 100%)

10 2nd Head White Intensity (0% <--> 100%)

11 3rd Head Red Intensity (0% <--> 100%)

12 3rd Head Green Intensity (0% <--> 100%)

13 3rd Head Blue Intensity (0% <--> 100%)

14 3rd Head White Intensity (0% <--> 100%)

15 4th Head Red Intensity (0% <--> 100%)

16 4th Head Green Intensity (0% <--> 100%)

17 4th Head Blue Intensity (0% <--> 100%)

18 4th Head White Intensity (0% <--> 100%)

19 Static Colors + Color Snap/Fade

20 Built-in Programs + Sound Active

21 Built-in Program Speed (slow <--> fast)

22 1st Head Pan Motor

23 1st Head Tilt Motor

24 2nd Head Pan Motor

25 2nd Head Tilt Motor

26 3rd Head Pan Motor

27 3rd Head Tilt Motor

28 4th Head Pan Motor

29 4th Head Tilt Motor

30 Pan Speed (0% <--> 100%)

31 Tilt Speed (0% <--> 100%)

32 Motor Reset (246-255)

Page 6

Figure 1: The BladeRunner™ RGBW Pin-Up Picture

4x Mini Moving Heads,

each tted with 1x CREE®

High Output RGBW

10-watt LED.

LED

Control

Panel

Bracket

Rubber

Feet

Mounting Holes

Stand

Mounting

Bracket

Figure 2: The Rear Connections

Power Switch

DMX In

Bracket

Mounting Holes

DMX Out

Rubber

Feet

Power In Power Out

Page 7

3. SETUP

Fuse Replacement

CAUTION! The BladeRunner™ RGBW utilizes a high-output switch-

mode power supply with an internal fuse. Under normal operating

conditions, the fuse should not require replacement. The fuse is eld replaceable, however it is an advanced procedure suited to qualied

individuals. Should your BladeRunner™ RGBW fuse require replacement, please contact Blizzard Lighting for instructions, or to return your unit for service.

Connecting A Bunch of BladeRunner™ RGBW Fixtures

You will need a serial data link to run light shows using a DMX-512

controller or to run shows on two or more xtures set to sync in master/

slave operating mode. The combined number of channels required by all

the xtures on a serial data link determines the number of xtures the

data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also, connecting more than 32 xtures on one serial data link without the

use of a DMX optically-isolated splitter may result in deterioration of the digital DMX signal. The maximum recommended cable-run distance is 500 meters (1640 ft).

The maximum recommended number of xtures on a serial data link is 32 xtures.

Data/DMX Cabling

To link xtures together you’ll need data cables. You should use data-

grade cables that can carry a high quality signal and are less prone to electromagnetic interference.

For instance, Belden© 9841 meets the specications for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but note that they cannot transmit DMX data as reliably over long distances. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft. Maximum capacitance between conductor & shield – 55 pF/ft. Maximum resistance of 20 ohms / 1000 ft. Nominal impedance 100 – 140 ohms

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the

xture’s chassis ground. Grounding the common can cause a ground loop, and your xture may perform erratically. Test cables with an

ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. They are widely available over the internet and from specialty retailers. If you’d like to build your own, the chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male (Input)

Ground/Shield Pin 1 Pin 1

DMX Data (-) Pin 2 Pin 2

DMX Data (+) Pin 3 Pin 3

Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output) on the controller.

Step 2: Connect the female connector of

the DMX cable to the rst xture’s male

connector (input). Note: It doesn’t matter

which xture address is the rst one

connected. We recommend connecting the

xtures in terms of their proximity to the

controller, rather than connecting the lowest

xture number rst, and so on.

Step 3: Connect other xtures in the chain

from output to input as above. Place a DMX

terminator on the output of the nal xture

to ensure best communication.

Page 9

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the DMX cable to the output

(female) 3 pin connector of the rst xture.

2. Connect the end of the cable coming from the rst xture which will have a (female) 3 pin connector to the input connector of the next xture consisting of

a (male) 3 pin connector. Then, proceed to connect from the output as stated

above to the input of the following xture and so on.

A quick note: Often, the setup for Master-Slave and Standalone operation

Mounting & Rigging

This xture may be mounted in any SAFE position provided there is enough

room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the xture

using a suitable “C” or “O” type clamp. The clamp should be rated to hold at

least 10x the xture’s weight to ensure structural stability. Do not mount to

surfaces with unknown strength, and ensure properly “rated” rigging is used

when mounting xtures overhead.

Adjust the angle of the xture by loosening both knobs and tilting the xture. After nding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp replacement access (if applicable) and routine maintenance.

requires that the rst xture in the

chain be initialized for this purpose via either settings in the control panel or DIP-switches. Secondarily,

the xtures that follow may also

require a slave setting.

Check the “Operating Adjustments” section in this manual for complete instructions for this type of setup and

conguration.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the xture will be exposed to rain, high

humidity, extreme temperature changes or restricted ventilation.

Lighting Stand Mounting

This xture comes with an easy to use stand mounting bracket. Please make

sure the lighting stand you use is rated to safely hold the weight of this unit and do not over-extend the lighting stand. For the safety of yourself, your audience,

and the xture... always take advantage of the use of the stand’s safety pins!

Page 10

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and different modes possible with the BladeRunner™ RGBW are accessed

by using the control panel on the front of the xture. There are 4 control buttons below

the LCD display which allow you to navigate through the various control panel menus.

MENU ENTERDOWNUP

Main Menu

To navigate through the LCD control panel main menu, use the <MENU> button to scroll through the various top level menu options. Then to scroll through sub-menu options, use the <UP/DOWN> buttons. Push the <ENTER> button to save any changes made.

Control Panel Menu Structure

Address 001-512 DMX Address CHND 14CH 14 Channel DMX Mode 32CH 32 Channel DMX Mode AUTO STOP/RUN Auto Mode (slower color changing) AUTO 1 STOP/RUN Auto Mode (faster color changing) AUDIO STOP/RUN Sound Active Mode

COLOR Red 1 Head 1 - Red (0-255) Green 1 Head 1 - Green (0-255) Blue 1 Head 1 - Blue (0-255) White 1 Head 1 - White (0-255) Red 2 Head 2 - Red (0-255) Green 2 Head 2 - Green (0-255) Blue 2 Head 2 - Blue (0-255) White 2 Head 2 - White (0-255) Red 3 Head 3 - Red (0-255) Green 3 Head 3 - Green (0-255) Blue 3 Head 3 - Blue (0-255) White 3 Head 3 - White (0-255) Red 4 Head 4 - Red (0-255) Green 4 Head 4 - Green (0-255) Blue 4 Head 4 - Blue (0-255) White 4 Head 4 - White (0-255) Shut Strobe Rate (0-255)

PROGRAM 01-20 Built-in Programs PRO-Movement ON/OFF Auto Movement On/Off SPEED <ENTER> Speed Settings Movement Movement Speed (001-255) Color Color Speed (001-255) LED ON/OFF LCD Backlight On/Off VERSION V1.0.0 Firmware Version RESET Yes? Fixture Reset

Page 11

DMX Mode

Allows the unit to be controlled by any universal DMX controller.

Set The DMX Starting Address

To assign a DMX staring address to the xture, use the <MENU> button to scroll to Address,

then use the <UP/DOWN> buttons to display any value within the range of 001-512. Then

push the <ENTER> button to conrm your choice.

DMX Mode Selection

To use the xture in either of its two DMX channel mode congurations, use the <MENU>

button to scroll to CHND, then use the <UP/DOWN> buttons to display either 14CH or 32CH.

Then push the <ENTER> button to conrm your choice.

Slave Mode

1.) Disconnect xture(s) from any DMX signal source.

2.) Set each xture to matching DMX modes (14CH or 32CH).

3.) Connect all xtures together via DMX. The rst xture in the DMX chain will be the master

xture, followed by the slave xtures.

4.) Connect DMX controller to the master unit for DMX control.

Stand-Alone, Master/Slave, Sound Active Modes:

Allows a single or Master/Slaved units to run factory installed programs at user selectable speeds.

PRO-Movement

This allows you to enable/disable auto movement of the heads in Program Mode or within Manual Color Adjustments. This will not effect movement in Auto or DMX modes.

1.) Use the <MENU> button to scroll to PRO-Movement, then use the <UP/DOWN> buttons

to display either ON or OFF. Then push the <ENTER> button to conrm your choice.

Speed Settings

This allows you to adjust the speed of the moving heads and color macros in Program Mode, Auto Mode or within Manual Color mixing. This will not effect speed in DMX mode.

1.) Use the <MENU> button to scroll to SPEED, then use the <UP/DOWN> buttons to display

either Movement or Color, then push the <ENTER> button. You can now adjust the speed

settings from 001-255 (slow <--> fast).

Auto Mode

To run the xture in auto mode, use the <MENU> button to scroll to AUTO or AUTO 1, then

push the <ENTER> button to conrm. You then adjust the movement and color macro speed

settings of the auto mode program (see Speed Settings).

Sound Active Mode

To run the xture in sound active mode, use the <MENU> button to scroll to AUDIO, then push

the <ENTER> button to conrm.

Page 12

Manual Color Adjustment

Allows the user to adjust the color balance of each individual moving head xture. You can set your own

intensity levels and then add PRO-Movement if you like! (See p. 12).

1.) Use the <MENU> button to scroll to COLOR, then use the <UP/DOWN> buttons to display

any of Red, Green, Blue, or White settings for xtures 1, 2, 3, and 4. Push the <ENTER> button

while highlighting any to display the color intensity range settings from 000-255. Use the <UP/

DOWN> buttons to adjust the intensity, then push <ENTER> to conrm your choice.

2.) The last option in the COLOR submenu is Shut (strobe). Using the same steps as above,

you can adjust the strobe rate values from 000-255 (slow <--> fast).

Program Mode

Allows a single unit to display a variety of colors and programs without a DMX controller.

1.) Use the <MENU> button to scroll to PROGRAM, then use the <UP/DOWN> buttons to

display the built-in program number from 01-20. Push the <ENTER> to conrm your choice. If

you wish, you can then also enable/disable PRO-Movement, or adjust the Speed Settings of the

Movement or Color Macros. (See p. 12)

LCD Display

To turn on/off the backlit LCD display, use the <MENU> button to scroll to LED, then push

<ENTER>. Then use the <UP/DOWN> buttons to scroll or either ON or OFF, and push

<ENTER> button to conrm your choice. ON will leave the display illuminated constantly, and

OFF will turn the display off after 40 seconds of idle.

Version

This menu option simply displays the xtures installed rmware version number.

Reset

To automatically reset the motors to automatically realign the moving head positions, use the

<MENU> button to scroll to RESET, then push <ENTER>.

Page 13

DMX Values In-Depth (14-Channel Mode)

Channel Value What It Does

1 000 <--> 255 Dimmer (0% <--> 100%)

2 000 <--> 255 Strobe (Slow <--> Fast)

3 000 <--> 255 Red Intensity (0% <--> 100%)

4 000 <--> 255 Green Intensity (0% <--> 100%)

5 000 <--> 255 Blue Intensity (0% <--> 100%)

6 000 <--> 255 White Intensity (0% <--> 100%)

000 <--> 028 029 <--> 057 058 <--> 086

9 000 <--> 255 Color Macro Speed (0% <--> 100%)

10 000 <--> 255 Pan

11 000 <--> 255 Tilt

12 000 <--> 255 Pan Speed (fast <--> slow)

13 000 <--> 255 Tilt Speed (fast <--> slow)

087 <--> 115 116 <--> 144 145 <--> 173 174 <--> 202 203 <--> 204 205 <--> 229 230 <--> 255

000 <--> 012 013 <--> 025 026 <--> 038 039 <--> 051 052 <--> 064 065 <--> 077 078 <--> 091 092 <--> 103 104 <--> 116 117 <--> 129 130 <--> 142 143 <--> 155 156 <--> 168 169 <--> 181 182 <--> 194 195 <--> 207 208 <--> 220 221 <--> 233 234 <--> 246 247 <--> 250 251 <--> 255

000 <--> 245 246 <--> 255

Static Colors + Color Snap/Fade

Red Green Blue White Red+Green Green+Blue Red+Blue Red+Green+Blue+White Color Snap Color Fade

Built-In Programs + Sound Active

Red Green Blue White Red+Green Green+Blue Red+Blue Red+Green+Blue+White Color Snap Color Fade Red+Green+Blue+White+Strobe (slow) Red+Green+Blue+White+Strobe (fast) Red Chase (1 head on, back and fourth) R/G/B/W Chase (1 head on, left to right) R/G/B/W Chase (1 head on, back and fourth) Green Chase (1 head on, left to right) Green Chase (1 head on, back and fourth) R/G/B/W Color Chase, Head 1+2 | 3+4 (all on) R/G/B/W Color Chase, Head 1+3 | 2+4 (all on) R/G/B/W Color Chase (all on) Sound Active Mode

No Function Reset Motors

DMX Values In-Depth (32-Channel Mode)

Channel Value What It Does

1 000 <--> 255 Dimmer (0% <--> 100%)

2 000 <--> 255 Strobe (Slow <--> Fast)

3 000 <--> 255 1st Head - Red Intensity (0% <--> 100%)

4 000 <--> 255 1st Head - Green Intensity (0% <--> 100%)

5 000 <--> 255 1st Head - Blue Intensity (0% <--> 100%)

6 000 <--> 255 1st Head - White Intensity (0% <--> 100%)

Page 14

DMX Values In-Depth (32-Channel Mode, continued)

Channel Value What It Does

7 000 <--> 255 2nd Head - Red Intensity (0% <--> 100%)

8 000 <--> 255 2nd Head - Green Intensity (0% <--> 100%)

9 000 <--> 255 2nd Head - Blue Intensity (0% <--> 100%)

10 000 <--> 255 2nd Head - White Intensity (0% <--> 100%)

11 000 <--> 255 3rd Head - Red Intensity (0% <--> 100%)

12 000 <--> 255 3rd Head - Green Intensity (0% <--> 100%)

13 000 <--> 255 3rd Head - Blue Intensity (0% <--> 100%)

14 000 <--> 255 3rd Head - White Intensity (0% <--> 100%)

15 000 <--> 255 4th Head - Red Intensity (0% <--> 100%)

16 000 <--> 255 4th Head - Green Intensity (0% <--> 100%)

17 000 <--> 255 4th Head - Blue Intensity (0% <--> 100%)

18 000 <--> 255 4th Head - White Intensity (0% <--> 100%)

000 <--> 028 029 <--> 057 058 <--> 086

21 000 <--> 255 Color Macro Speed (0% <--> 100%)

22 000 <--> 255 1st Head - Pan

23 000 <--> 255 1st Head - Tilt

24 000 <--> 255 2nd Head - Pan

25 000 <--> 255 2nd Head - Tilt

26 000 <--> 255 3rd Head - Pan

27 000 <--> 255 3rd Head - Tilt

28 000 <--> 255 4th Head - Pan

29 000 <--> 255 4th Head - Tilt

30 000 <--> 255 Pan Speed (fast <--> slow)

31 000 <--> 255 Tilt Speed (fast <--> slow)

087 <--> 115 116 <--> 144 145 <--> 173 174 <--> 202 203 <--> 204 205 <--> 229 230 <--> 255

000 <--> 245 246 <--> 255

Static Colors + Color Snap/Fade

Red Green Blue White Red+Green Green+Blue Red+Blue Red+Green+Blue+White Color Snap Color Fade

Built-In Programs + Sound Active

No Function Reset Motors

Page 15

5. APPENDIX

A Quick Lesson On DMX

DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common communications standard used by lighting and related stage equipment.

DMX provides up to 512 control “channels” per data link. Each of these channels was originally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an 8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb being completely off while 255 corresponds to the light bulb being fully on.

DMX data is transmitted at 250,000 bits per second using the RS-485 transmission standard over two wires. As with microphone cables, a grounded cable shield is used to prevent interference with other signals.

There are ve pins on a DMX connector: a wire for ground (cable shield), two wires for

“Primary” communication which goes from a DMX source to a DMX receiver, and two wires for a “Secondary” communication which goes from a DMX receiver back to a DMX

source. Generally, the “Secondary” channel is not used so data ows only from sources

to receivers. Hence, most of us are most familiar with DMX-512 as being employer over

typical 3-pin “mic cables,” although this does not conform to the dened standard.

DMX is connected using a daisy-chain conguration where the source connects to the input of the rst device, the output of the rst device connects to the input of the next device,

and so on. The standard allows for up to 32 devices on a single DMX link.

Each receiving device typically has a means for setting the “starting channel number” that

it will respond to. For example, if two 6-channel xtures are used, the rst xture might

be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next

xture would be set to start at channel 7 so it would respond to channels 7 through 12.

Troubleshooting

Symptom Solution

Fixture AutoShut Off

Beam is Dim Check optical system and clean excess dust/grime. Also ensure that

No Light Output Check to ensure xture is operating under correct mode, IE sound

Chase Speed Too Fast/Slow

No Power Check fuse, AC cord and circuit for malfunction.

No Response to Audio

Fixture Not Responding / Responding Erratically

Check the fan in the xture. If it is stopped or moving slower than

normal, the unit may have shut itself off due to high heat. This is to

protect the xture from overheating. Clear the fan of obstructions,

or return the unit for service.

the 220V/110V switch is in the correct position, if applicable.

active/auto/DMX/Etc., if applicable. Contact service for more information.

Check to ensure proper setup of speed adjustment.

Verify that the xture is in “Sound Active” mode.

Adjust Audio Sensitivity, If Applicable.

Make sure all connectors are seated properly and securely. Use Only DMX Cables. Install a Terminator. Check all cables for defects.

Reset xture(s).

Page 16

Keeping Your BladeRunner™ RGBW As Good As New

The xture you’ve received is a rugged, tough piece of pro lighting equipment,

and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed.

You should absolutely keep the xture clean, especially if you are using it in an

environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve the quality of light output. Keeping the fans free of dust and debris will keep

the xture running cool and prevent damage from overheating.

In transit, keep the xtures in cases. You wouldn’t throw a prized guitar,

drumset, or other piece of expensive gear into a gear trailer without a case, and similarly, you shouldn’t even think about doing it with your shiny new light

xtures.

Common sense and taking care of your xtures will be the single biggest thing

you can do to keep them running at peak performance and let you worry about designing a great light show, putting on a great concert, or maximizing your client’s satisfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry about sending a defective unit back, or sending a unit in for service. But, like any complex piece of equipment designed and built by humans, once in a

while, something doesn’t go as planned. If you nd yourself with a xture that isn’t behaving like a good little xture should, you’ll need to obtain a Return

Authorization (RA).

Don’t worry, this is easy. Just send an email to support@blizzardlighting.com, and we’ll issue you an RA. Then, you’ll need to send the unit to us using a trackable, pre-paid freight method. We suggest using USPS Priority or UPS.

Make sure you carefully pack the xture for transit, and whenever possible, use

the original box & packing for shipping.

When returning your xture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the xture. Please remember

that any shipping damage which occurs in transit to us is the customer’s responsibility, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and must be reported to the carrier immediately upon receipt of the items. Claims must be made within seven (7) days of receipt.

Page 17

Tech Specs!

Weight & Dimensions

Length 40.5 inches (102.9 cm)

Height 8.25 inches (21 cm)

Depth Base: 3.27” (8.3 cm), Head: 5” (12.7 cm)

Weight 22.1 lbs (10 kg)

Power

Operating Voltage AC 110-240VAC, 50-60 Hertz

Power Consumption 77w, 1.13A

Power Factor .6

Light Source

LED 4* 10-watt R/G/B/W CREE® LEDs

Optical

Beam Angle 2 degree

Thermal

Max. Operating

104 degrees F (40 degrees C) ambient

Temp.

Control

Protocol USITT DMX-512

DMX Channels 14 or 32 Channels

Input 3-pin XLR Male

Output 3-pin XLR Female

Other Operating Modes Standalone, Master/Slave, Auto, Sound Active

Other Information

If you have a pear shaped body, you should not wear pear colored clothes, or act juicy.

2-year limited warranty, does not cover mal-

Warranty

DISCLAIMER:

The power connector tted to the xture and xture cord are designed for compatibility

with products manufactured by Neutrik AG, Neutrik USA and their related entities, how-

ever they are not manufactured by, afliated with or endorsed by Neutrik AG, Neutrik

USA, or any related entity. Neutrik® and powerCON® are registered trademarks of Neutrik AG.

function caused by damage to LED’s.

Page 18

Luminous Intensity

Lux/Meter 1 Meter 2 Meter

Red 10,270 Lux 3,460 Lux

Green 13,590 Lux 4,700 Lux

Blue 15,560 Lux 6,050 Lux

White 21,000 Lux 6,700 Lux

Dimensional Drawings

40.5 in

4.8 in

8.25 in

5 in

3.27 in

Page 19

Enjoy your product!

Our sincerest thanks for your purchase!

--The team @ Blizzard Lighting

Blizzard Lighting BladeRunner RGBW User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual