Blizzard Lighting 500 HushPar Infiniwhite User Manual

HUSH

PA R

InfInI whIte

500

tM

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Copyright (c) 2014

TABLE OF CONTENTS

HushPar™ Inniwhite 500 1

1. Getting Started 3

What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4

2. Meet The HushPar™ Inniwhite 500 5

Features 5
DMX Quick Reference 5
The HushPar™ Inniwhite 500 Pin-up Picture 6

3. Setup 7

Fuse Replacement 7
Connecting A Bunch Of HushPar™ Inniwhite 500 PAR Cans 7
Data/DMX Cables 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9

4. Operating Adjustments 12

Navigating The Control Panel 12
Control Panel Menu Structure 13
DMX Mode 14
Master/Slave Mode 14
Sound Active Mode 14
Standalone (Program) Mode 14
Manual Color Adjustment 14
DMX Channel Values In-Depth 15
Troubleshooting 17

5. Appendix 18

A Quick DMX Lesson 18
Keeping Your HushPar™ As Good As New 19
Returns (Gasp!) 19
Shipping Issues 19

Tech Specs 20

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 2

1. GETTING STARTED

What’s In The Box?

• 1 x HushPar™ Inniwhite 500 Professional LED PAR Fixture

• This Lovely User Manual

Getting It Out Of The Box

Congratulations on purchasing one of the most rocking box-shaped PAR xtures any­where! Now that you’ve got your HushPar™ Inniwhite 500 (or hopefully, HushPares!),

you should carefully unpack the box and check the contents to ensure that all parts are
present and in good condition. If anything looks as if it has been damaged in transit,
notify the shipper immediately and keep the packing material for inspection. Again,

please save the carton and all packing materials. If a xture must be returned to the
factory, it is important that the xture be returned in the original factory box and pack

ing.

Powering Up!

All xtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch.

AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that
the xture you receive is suitable for your local power supply. See the label on the
xture or refer to the xture’s specications chart for more information. A xture’s
listed current rating is its average current draw under normal conditions. Check the
xture or device carefully to make sure that if a voltage selection switch exists that it is
set to the correct line voltage you will use.

Warning! Verify that the voltage select switch on your unit matches the line

voltage applied. Damage to your xture may result if the line voltage applied

does not match the voltage indicated on the voltage selector switch. All

xtures must be connected to circuits with a suitable Ground (Earthing).

-

Getting A Hold Of Us

If something is wrong, just give us a call or send an email. We’ll be happy to

help, honest.

Blizzard Lighting

N16 W23390 Stoneridge Dr. Suite E
Waukesha, WI 53188 USA

www.blizzardlighting.com

414-395-8365
Email: [e-mail]

Disclaimer: The information and specications contained in this document are subject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability
for any errors or omissions that may appear in this user manual. Blizzard Lighting™

reserves the right to update the existing document or to create a new document to
correct any errors or omissions at any time. You can download the latest version of this

document from www.blizzardlighting.com.

Author: Date: Last Edited: Date:

J. Thomas 01/14/2014 J. Thomas 01/14/2014

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 3

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the de­cal or rear panel of the xture.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

cord. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech­nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at sup­[e-mail].

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 4

2. MEET THE HUSHPAR™ INFINIwHITE 500 LED PAR

MAIN FEATURES:

• 36x 3-watt 3-in-1 Amber/Cool White/Warm White LED’s

• Full color mixing in standalone, master/slave and DMX modes

• Efcient convection cooling for zero fan noise

• Built-in automated programs via master/slave

• Built-in sound activated programs via master/slave

• Easy to use LED digital control panel

• Dual mounting yoke allows exibility in positioning

• Rugged die cast aluminum enclosure

OPTICAL:

• Installed optics: 25 degree

• Constant current driver: 500MA

• PWM Dimmer: 400HZ (16666 steps)

• Amber=590-595nm, WW=3000-3300K, CW=8000-9000K

DMX Quick Reference - 7 / 8 Channel Mode

Channel 7-Channel 8-Channel

1 Dimmer Dimmer

2 Amber Intensity Amber Intensity

3 Warm White Intensity Warm White Intensity

4 Cool White Intensity Cool White Intensity

5 Strobe Strobe

6 Built-In Programs Built-In Programs

7 ACW Gradual Mixing ACW Gradual Mixing

8 --- 32-bit dimmer (Set by Display

on xture) 0-4

DMX Quick Reference - 3-Channel (ACW) / 6-Channel Mode

Channel 3-Channel - ACW 5-Channel

1 Amber Intensity Dimming

2 Warm White Intensity Amber Intensity

3 Cool White Intensity Warm White Intensity

4 --- Cool White Intensity

5 --- Strobe

6 --- Built-In Programs

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 5

Figure 1: The HushPar™ Inniwhite 500 Pin-Up Picture

Heavy-duty Die

Cast Aluminum

Enclosure

Locking

Knobs

Figure 2: The Rear Connections

High Power

5w 3-in-1 LEDs

Dual Mounting

Brackets

DMX In DMX Out

LED Display

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 6

Menu Buttons

3. SETUP

Fuse Replacement

CAUTION! The HushPar™ Inniwhite 500 utilizes a high-output

switch-mode power supply with an internal fuse. Under normal oper­ating conditions, the fuse should not require replacement. The fuse is
eld replaceable, however it is an advanced procedure suited to quali­ed individuals. Should your HushPar™ Inniwhite 500 fuse require

replacement, please contact Blizzard Lighting for instructions, or to

return your unit for service.

Connecting A Bunch of HushPar™ Inniwhite 500 Fixtures

You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in mas­ter/slave operating mode. The combined number of channels required
by all the xtures on a serial data link determines the number of x-

tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also, connecting more than 32 xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640
ft). The maximum recommended number of xtures on a serial data
link is 32 xtures.

Data/DMX Cabling

To link xtures together you’ll need data cables. You should use data­grade cables that can carry a high quality signal and are less prone to

electromagnetic interference.

For instance, Belden© 9841 meets the specications for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but

note that they cannot transmit DMX data as reliably over long distanc­es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 7

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR

connector on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the x-

ture’s chassis ground. Grounding the common can cause a ground

loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not

grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output)

5-Pin Male
(Input)

Ground/Shield Pin 1 Pin 1

DMX Data (-) Pin 2 Pin 2

DMX Data (+) Pin 3 Pin 3

Not Used. No Connection. No Connection.

Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output)

on the controller.

Step 2: Connect the female connector of the

DMX cable to the rst xture’s male connec-

tor (input). Note: It doesn’t matter which

xture address is the rst one connected.
We recommend connecting the xtures in

terms of their proximity to the controller,

rather than connecting the lowest xture
number rst, and so on.

Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture

to ensure best communication.

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 8

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the

DMX cable to the output (female) 3 pin connector of
the rst xture.

2. Connect the end of the cable coming from the

rst xture which will have a (female) 3 pin connec­tor to the input connector of the next xture con-

sisting of a (male) 3 pin connector. Then, proceed

to connect from the output as stated above to the
input of the following xture and so on.

A quick note: Often,

the setup for Master­Slave and Standalone
operation requires that
the rst xture in the

chain be initialized for

this purpose via either

settings in the control

panel or DIP-switches.
Secondarily, the xtures
that follow may also re­quire a slave setting.

Check the “Operating Adjustments” section in this manual for com­plete instructions for this type of setup and conguration.

Mounting & Rigging

This xture may be mounted in any SAFE position provided there is
enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the
xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the xture’s weight to ensure structural sta-

bility. Do not mount to surfaces with unknown strength, and ensure

properly “rated” rigging is used when mounting xutres overhead.

Adjust the
angle of the xture by loosening both knobs and tilting the xture.
After nding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp

replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 9

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and different modes possible with the HushPar™ Inni­white 500 LED are accessed by using the control panel on the rear of
the xture. There are 4 control buttons below the LED display which
allow you to navigate through the various control panel menus.

<MENU>

Is used to navigate to the previous higher-level menu item.

<UP>

Scrolls through menu items and numbers in ascending order.

<DOWN>

Scrolls through menu items and numbers in descending order.

<ENTER>

Is used to select and conrm/store the current selection.

The Control Panel LED Display shows the menu items you select from

the menu map on page #11. When a menu function is selected, the

display will show immediately the rst available option for the selected

menu function. To select a menu item, press <ENTER>.

Press the <MENU> button repeatedly until you reach the desired
menu function. Use the <UP> and <DOWN> buttons to navigate the
menu options. Press the <ENTER> button to select the menu function

currently displayed, or to enable a menu option. To return to the previ­ous option or menu without changing the value, press the

<MENU> button.

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 10

Control Panel Menu Structure

Addr d001 - d512 To choose the DMX address

SLAU SL.AU To run the xture in slave mode

CHnd 8CH 8 channel DMX mode

7CH 7 channel DMX mode

6CH 6 channel DMX mode

3CH 3 channel DMX mode

SP -- SP00 -SP15 Speed adjustments (0-15)

Pr -- Pr00 -Pr15 Built-in programs (0-15)

ASC - AC00 -AC15 Auto mode (0-15)

FAdE FA00 -FA15 Fade settings (0-15)

FLAS FL00 -FL15 Flash / strobe speed (0-15)

rL -- r.000 - r.255 Amber dimmer (0% <--> 100%)

GL -- G.000 - G.255 Warm White dimmer (0% <--> 100%)

bL -- b.000 - b.255 Cool White dimmer (0% <--> 100%)

SouA So.uA Sound active mode

LED on - oFF Display menu on/off

nodE nod0-nod4 Dimming mode (0-4)

UErn UE2.0 Software version

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 11

DMX Mode

Allows the unit to be controlled by any universal DMX controller.

1.) The default mode for the xture is DMX, which appears as

select a different DMX address, using the <MENU> button, select

Use the <UP/DOWN> buttons to select the correct address, then hit <ENTER> to conrm.

Setting the DMX Channel Mode:

1.) To select a DMX channel mode, press the <MENU> button, then use the <UP> or

<DOWN> buttons until the display reads

the <UP> or <DOWN> buttons until the display reaches your desired channel mode. Press the

<MENU> button to conrm.

Chnd and press the <MENU> button. Then use

d001 on the LED Readout. To

Addr,then hit <ENTER>.

Stand-Alone, Master/Slave, Sound Active Modes:

Allows a single or Master/Slaved units to run factory installed programs at user selectable speeds.

1.) To set the xture in Flash/Fade mode, select

<ENTER> button.

2.) Now, you can adjust the ash settings from

FLAS or FAdE. To conrm, press the

FL00-FL15 or the fade settings from

FA00-FA15. Then press the <ENTER> button to conrm.

3.) To use the xture in automatic mode, select

use the <UP/DOWN> to choose from

conrm.

4.) Adjust the speed of the chase as above using

press the <ENTER> button to conrm.

5.) To set the xture as a slave unit, select

ashing

SL.AU to indicate it is in slave mode.

Sound Active Mode:

1.) To use sound active mode, select

SouA, then press the <ENTER> button to conrm.

Standalone (Program) Mode:

Allows a single unit to display a variety of colors and programs without a DMX controller.

1.) To set the xture in manual mode, select Pr--.

To conrm, press the <ENTER> button.

2.) Now, select the program by using the <UP> and <DOWN> buttons to select

. To conrm, press the <ENTER> button.

Pr15

Manual Color Adjustment:

Allows the user to adjust the color balance of the xture. These settings are global, they will effect all

modes.

1.) Use the <MENU> and <UP/DOWN> button to select

White Level),

2.) Using the <UP/DOWN> buttons, select the maximum level for each color between

bL-- (Cool White Level), then hit <ENTER>.

ASC-, and press the <ENTER> button. Then

AS00-AS15, then press the <ENTER> button to

SP15 (slowest) to SP00 (fastest) then

SLAU, and hit <ENTER>. The unit will display a

Pr00-

rL-- (Amber Level), GL-- (Warm

x000-x255 (000=off), then hit <ENTER> to conrm.

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 12

DMX Values In-Depth (8-Channel Mode)

Channel Value What It Does

1 000 <--> 255 Dimmer (0% <--> 100%)

2 000 <--> 255 Amber Intensity (0% <--> 100%)

3 000 <--> 255 Warm White Intensity (0% <--> 100%)

4 000 <--> 255 Cool White Intensity (0% <--> 100%)

5

6

7

Ch. 1 Controls

Saturation

8

000 <--> 014
015 <--> 255

000 <--> 031
032 <--> 063
064 <--> 095
096 <--> 127
128 <--> 159
160 <--> 191
192 <--> 223
224 <--> 255

000 <--> 009
010 <--> 029
030 <--> 039
040 <--> 049
050 <--> 069
070 <--> 079
080 <--> 089
090 <--> 109
110 <--> 119
120 <--> 129
130 <--> 149
150 <--> 159
160 <--> 169
170 <--> 189
190 <--> 199
200 <--> 219
220 <--> 229
230 <--> 249
250 <--> 255

000 <--> 005
006 <--> 055
056 <--> 105
106 <--> 155
156 <--> 205
206 <--> 255

Strobe

Dimming

Strobe (Slow <--> Fast)

Fade, Color Change, Sound Active

No Function

Fade In (Ch. 5 Controls Speed)
Fade Out (Ch. 5 Controls Speed)
Fade In / Fade Out (Ch. 5 Controls Speed)
ACW Gradual Change (Ch. 5 Controls Speed)
Fade In / Fade Out, Auto Run
Color Jump (Ch. 5 Controls Speed)
Sound Active

Color Saturation

Invalid

A 100%

A85%+(A+C)15%
A60%+(A+C)40%
(A+C)100%
(A+C)85%+C15%
(A+C)60%+C40%

C 100%

C85%+W15%
C60%+W40%

W 100%

W85%+(C+W)15%
W60%+(C+W)40%
(C+W)100%
(C+W)50%+(A+W)50%
(A+W)100%
(A+W)50%+(A+C+W)50%
(A+C+W)95%+(A+C)5%

All Colors on 100%

32-Bit Dimmer

As set in the control menu display

Mode 0 = 8-bit, 256 dimming steps
Mode 1 = 32-bit, 0-25% intensity range
Mode 2 = 32-bit, 0-50% intensity range
Mode 3 = 32-bit, 0-75% intensity range
Mode 4 = 32-bit, full intensity dimming

DMX Values In-Depth (7-Channel Mode)

Channel Value What It Does

1 000 <--> 255 Dimmer (0% <--> 100%)

2 000 <--> 255 Amber Intensity (0% <--> 100%)

3 000 <--> 255 Warm White Intensity (0% <--> 100%)

4 000 <--> 255 Cool White Intensity (0% <--> 100%)

5

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

000 <--> 014
015 <--> 255

Strobe

Dimming

Strobe (Slow <--> Fast)

Page 13

DMX Values In-Depth (7-Channel Mode, Continued)

Channel Value What It Does

6

7

Ch. 1 Controls

Saturation

000 <--> 031
032 <--> 063
064 <--> 095
096 <--> 127
128 <--> 159
160 <--> 191
192 <--> 223
224 <--> 255

000 <--> 009
010 <--> 029
030 <--> 039
040 <--> 049
050 <--> 069
070 <--> 079
080 <--> 089
090 <--> 109
110 <--> 119
120 <--> 129
130 <--> 149
150 <--> 159
160 <--> 169
170 <--> 189
190 <--> 199
200 <--> 219
220 <--> 229
230 <--> 249
250 <--> 255

Fade, Color Change, Sound Active

No Function

Fade In (Ch. 5 Controls Speed)
Fade Out (Ch. 5 Controls Speed)
Fade In / Fade Out (Ch. 5 Controls Speed)
ACW Gradual Change (Ch. 5 Controls Speed)
Fade In / Fade Out, Auto Run
Color Jump (Ch. 5 Controls Speed)
Sound Active

Color Saturation

Invalid

A 100%

A85%+(A+C)15%
A60%+(A+C)40%
(A+C)100%
(A+C)85%+C15%
(A+C)60%+C40%

C 100%

C85%+W15%
C60%+W40%

W 100%

W85%+(C+W)15%
W60%+(C+W)40%
(C+W)100%
(C+W)50%+(A+W)50%
(A+W)100%
(A+W)50%+(A+C+W)50%
(A+C+W)95%+(A+C)5%

All Colors on 100%

DMX Values In-Depth (6-Channel Mode)

Ch. Value What It Does

1 000 <--> 255 Dimmer (0% <--> 100%)

2 000 <--> 255 Amber Intensity (0% <--> 100%)

3 000 <--> 255 Warm White Intensity (0% <--> 100%)

4 000 <--> 255 Cool White Intensity (0% <--> 100%)

5

6

000 <--> 014
000 <--> 255

000 <--> 031
032 <--> 063
064 <--> 095
096 <--> 127
128 <--> 164
165 <--> 191
192 <--> 223
224 <--> 255

Strobe

Dimming

Strobe (Slow <--> Fast)

Fade, Color Change, Sound Active

No Function

Fade In (Ch. 5 Controls Speed)
Fade Out (Ch. 5 Controls Speed)
Fade In / Fade Out (Ch. 5 Controls Speed)
ACW Gradual Change (Ch. 5 Controls Speed)
Fade In / Fade Out, Auto Run
Color Jump (Ch. 5 Controls Speed)
Sound Active

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 14

DMX Values In-Depth (3-Channel ACW Mode)

Ch. Value What It Does (3 Ch.)

1 000 <--> 255 Amber Intensity (0% <--> 100%)

2 000 <--> 255 Warm White Intensity (0% <--> 100%)

3 000 <--> 255 Cool White Intensity (0% <--> 100%)

Troubleshooting

Symptom Solution

Fixture Auto-Shut

Off

Check the fan in the xture. If it is stopped or
moving slower than normal, the unit may have
shut itself off due to high heat. This is to pro­tect the xture from overheating. Clear the fan
of obstructions, or return the unit for service.

Beam is Dim Check optical system and clean excess dust/

grime. Also ensure that the 220V/110V switch

is in the correct position, if applicable.

No Light Output Check to ensure xture is operating under cor-

rect mode, IE sound active/auto/DMX/Etc., if

applicable.

Chase Speed Too
Fast/Slow

Check to ensure proper setup of speed adjust-

ment.

No Power Check fuse, AC cord and circuit for malfunction.

Blown Fuse Check AC cord and circuit for damage, verify

that moving parts are not restricted and that
unit’s ventilation is not obstructed

Slow Movement Verify that 220V/110V switch is in the correct

position, if applicable. Also check that speed
channels are set appropriately.

No Response to

Audio

Fixture Not

Responding /
Responding
Erraticly

Verify that the xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.

Make sure all connectors are seated properly

and securely.

Use Only DMX Cables and/or check cables for

defects
Install a Terminator.

Reset xture(s).

Fixture Moving On

Its Own

Verify proper mode of operation. Is the xture

in “Auto” mode?

If your problem persists or isn’t listed contact [e-mail].

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 15

5. APPENDIX

A Quick Lesson On DMX

DMX (aka DMX-512) was created in 1986 by the United States Institute for Theatre

Technology (USITT) as a standardized method for connecting lighting consoles to lighting

dimmer modules. It was revised in 1990 and again in 2000 to allow more exibility. The
Entertainment Services and Technology Association (ESTA) has since assumed control over
the DMX512 standard. It has also been approved and recognized for ANSI standard clas­sication.

DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common
communications standard used by lighting and related stage equipment.

DMX provides up to 512 control “channels” per data link. Each of these channels was origi­nally intended to control lamp dimmer levels. You can think of it as 512 faders on a lighting
console, connected to 512 light bulbs. Each slider’s position is sent over the data link as an
8-bit number having a value between 0 and 255. The value 0 corresponds to the light bulb
being completely off while 255 corresponds to the light bulb being fully on.

DMX data is transmitted at 250,000 bits per second using the RS-485 transmission stan­dard over two wires. As with microphone cables, a grounded cable shield is used to prevent

interference with other signals.

There are ve pins on a DMX connector: a wire for ground (cable shield), two wires for
“Primary” communication which goes from a DMX source to a DMX receiver, and two wires
for a “Secondary” communication which goes from a DMX receiver back to a DMX source.
Generally, the “Secondary” channel is not used so data ows only from sources to receiv­ers. Hence, most of us are most familiar with DMX-512 as being employer over typical
3-pin “mic cables,” although this does not conform to the dened standard.

DMX is connected using a daisy-chain conguration where the source connects to the input
of the rst device, the output of the rst device connects to the input of the next device,
and so on. The standard allows for up to 32 devices on a single DMX link.

Each receiving device typically has a means for setting the “starting channel number” that
it will respond to. For example, if two 6-channel xtures are used, the rst xture might
be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next
xture would be set to start at channel 7 so it would respond to channels 7 through 12.

The greatest strength of the DMX communications protocol is that it is very simple and
robust. It involves transmitting a reset condition (indicating the start of a new “packet”),
a start code, and up to 512 bytes of data. Data packets are transmitted continuously. As
soon as one packet is nished, another can begin with no delay if desired (usually another
follows within 1 ms). If nothing is changing (i.e. no lamp levels change) the same data will
be sent out over and over again. This is a great feature of DMX -- if for some reason the
data is not interpreted the rst time around, it will be re-sent shortly.

Not all 512 channels need to be output per packet, and in fact, it is very uncommon to nd
all 512 used. The fewer channels are used, the higher the “refresh” rate. It is possible to
get DMX refreshes at around 1000 times per second if only 24 channels are being trans­mitted. If all 512 channels are being transmitted, the refresh rate is around 44 times per

second.

In summary, since its design and evolution in the 1980’s DMX has become the standard
for lighting control. It is exible, robust, and scalable, and its ability to control everything
from dimmer packs to moving lights to foggers to lasers makes it an indispensable tool for

any lighting designer or lighting performer.

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 16

Keeping Your HushPar™ Inniwhite 500 As Good As New

The xture you’ve received is a rugged, tough piece of pro lighting equip-

ment, and as long as you take care of it, it will take care of you. That said, like
anything, you’ll need to take care of it if you want it to operate as designed.

You should absolutely keep the xture clean, especially if you are using it in an
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled

drinks.

Cleaning the optics routinely with a suitable glass cleaner will greatly improve
the quality of light output. Keeping the fans free of dust and debris will keep
the xture running cool and prevent damage from overheating.

In transit, keep the xtures in cases. You wouldn’t throw a prized guitar,
drumset, or other piece of expensive gear into a gear trailer without a case,
and similarly, you shouldn’t even think about doing it with your shiny new light
xtures.

Common sense and taking care of your xtures will be the single biggest thing

you can do to keep them running at peak performance and let you worry about
designing a great light show, putting on a great concert, or maximizing your cli­ent’s satisfaction and “wow factor.” That’s what it’s all about, after all!

Returns (Gasp!)

We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But, like
any complex piece of equipment designed and built by humans, once in a while,
something doesn’t go as planned. If you nd yourself with a xture that isn’t
behaving like a good little xture should, you’ll need to obtain a Return Authori­zation (RA).

Don’t worry, this is easy. Just send an email to [e-mail],
and we’ll issue you an RA. Then, you’ll need to send the unit to us using a
trackable, pre-paid freight method. We suggest using USPS Priority or UPS.
Make sure you carefully pack the xture for transit, and whenever possible, use

the original box & packing for shipping.

When returning your xture for service, be sure to include the following:

1.) Your contact information (Name, Address, Phone Number, Email address).

2.) The RA# issued to you

3.) A brief description of the problem/symptoms.

We will, at our discretion, repair or replace the xture. Please remember that

any shipping damage which occurs in transit to us is the customer’s responsibil­ity, so pack it well!

Shipping Issues

Damage incurred in shipping is the responsibility of the shipper, and
must be reported to the carrier immediately upon receipt of the items.

Claims must be made within seven (7) days of receipt.

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 17

Tech Specs!

Weight & Dimensions

Length

Width

Height

Weight

13 inches (33 cm)

12.6 inches (32 cm)

15.4 inches (39 cm)

12.1 pounds (5.5 kg)

Power

Operating Voltage 100-264VAC, 47-63 Hertz

Fuse 3A 250V

Power Consumption 90W

Light Source

LED 18x 5W 3-in-1 LEDs 100,000 hours.

Optical

Beam Angle 25 degree optics

Thermal

Max. Operating Temp. 104 degrees F (40 degrees C) ambient

Control

Protocol USITT DMX-512

DMX Channels 3 / 6 / 7 / 8

Input 3-pin XLR Male

Output 3-pin XLR Female

Standalone, Master/Slave, Sound Active, Color

Other Operating Modes

Preset

Innity

Nature’s way of procrastinating.

2-year limited warranty, does not cover mal

Warranty

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

function caused by damage to LED’s.

Page 18

-

This page left intentionally blank

HushPar Inniwhite Manual Rev. A © 2014 Blizzard Lighting, LLC

Page 19

Enjoy your product!

Our sincerest thanks for your purchase!

--The team @ Blizzard Lighting