Page 1
BCC1
Installation, Operation & Maintenance Manual
(HC Gas R290 used)
Page 1
Page 2
Safety Tips
Position on a flat, stable surface.
A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove
any components or service panels on this product.
Consult Local and National Standards to comply with
The following:
·Health and Safety at Work Legislation
·BS EN Codes of Practice
·Fire Precautions
·IEE Wiring Regulations
·Building Regulations
DO NOT use jet/pressure washers to clean the appliance.
DO NOT use the appliance outside.
DO NOT use this appliance to store medical supplies.
DO NOT use electrical appliances inside the appliance.
(e.g. heaters, ice-cream makers etc.)
DO NOT stand or support yourself on the base,
drawers or doors.
DO NOT allow oil, fat or greases to come into contact with the
surfaces, plastic components or door seal. Clean immediately if
contact occurs. This can cause brown spots or staining
to appear on the stainless steel
Bottles that contain a high percentage of alcohol must
be sealed and placed vertically in the refrigerator.
Always carry, store and handle the appliance in a
vertical position and move by holding the base of the
appliance.
Always switch off and disconnect the power supply to
the unit before cleaning.
Keep all packing away from children. Dispose of the
packaging in accordance with the regulations of local
authorities.
If the power cord is damaged, it must be replaced by
an agent or a recommended qualified technician in
order to avoid a hazard.
Introduction
Please take a few moments to carefully read through this
manual. Correct maintenance and operation of this
machine will provide the best possible performance from
your product.
Pack Contents
The following is included：
·Refrigerator or Freezer
·Shelf guides (2 per door)
·Shelves (1 per door)
·Instruction manual
·Keys
We pride ourselves on quality and service, ensuring that
at the time of packing the contents are supplied fully
functional and free of damage. Should you find any
damage as a result of transit, please contact your dealer
immediately.
Installation
Note: If the unit has not been stored or move in an
upright position, let it stand upright for approximately
12 hours before operation. If in doubt allow to stand.
1. Remove the appliance from the packaging. Make
sure that all protective plastic film and coatings
are thoroughly removed from all surfaces.
2. Maintain a distance of 20 cm (7 inches) between
the unit and walls or other objects for ventilation
increase this distance if the obstacle is a heat
source.
Note: Before using the appliance for the first time,
clean the shelves and interior with soapy water.
3. Set the brakes on the castors to keep the appliance
in position OR level the appliance by adjusting the screw feet.
4. Ensure the ambient temperature is within the design range of
the cabinet, avoid locations below 15 degrees C. Beware of
enclosed rooms with other refrigeration equipment as
additional ventilation may be required
Fitting the Shelves
1. Place one set of shelf guides on either side of the cabinet
at the desired height.
2. Slide the shelf into place.
3. Repeat for the remaining shelves.
Storing Food
To get the best result from your appliance, follow these instruction:
·Only store foodstuffs in the appliance when it has reached the
correct operating temperature.
·Do not place uncovered hot food or liquid inside the appliance.
·Warp or cover food where possible.
·Do not obstruct the fans inside the appliance.
·Ensure that the load is equally distributed throughout and that
air can circulate around and through stored products
·Avoid opening the doors for prolonged periods of time.
Turn on
1. Close the door(s) of the appliance.
2. Ensure the power switch is set to [O] and turn on at the socket.
3. Switch on the power [l]. The current temperature within the
the appliance is displayed.
Adjusting the Set Temperature
1. Press and hold the set button for 3 seconds till the C led starts
blinking with the current set temperature shown
2. Use the arrow keys to adjust to the required set temperature
setting.
3. Press the set key to store, then leave for approx. 5 secs till the
display shows the cabinet temperature, the cabinet will then cool
down to the new set temperature.
NOTE! The temperature shown on the display will fluctuate during
normal use as the unit regulates the cabinet temperature.
Manual Defrost
The appliance will automatically run a defrost cycle every six hours.
Note: The cycle starts from the time the appliance is initially
powered up.
To manually defrost the appliance:
1. Press and hold the DEFROST button for 5 seconds.
2. The defrost cycle will start immediately and the Defrost
LET illuminates. The defrost will last a maximum of 30 minutes.
Note: Starting a manual defrost also resets the automatic defrost
timer.
3. The next automatic defrost will start six hours after the manual
defrost has finished.
Page 2
Page 3
ROUTINE MAINTENANCE
the temperature is too
Appliance is located near a heat source
or air flow to the condenser is being
he appliance is leaking
Movement of water to the drain is
he appliance is unusually
Regular servicing of the appliance should be undertaken to ensure
it is functioning as intended and correctly and it is safe to use. Safely
disconnect the appliance from the power supply before cleaning,
servicing or undertaking general maintenance. This appliance must
be maintained at regular intervals. The frequency of maintenance
will depend upon the appliance’s specific use and location. The
maximum service interval should be 12 months.
Note: Service and maintenance should only be undertaken by
suitably qualified technicians
cleaning.
· Clean the interior of the appliance as often as possible.
· Do not use abrasive cleaning agents. These can leave harmful
residues.
· Clean the door seal with water only.
· Always wipe dry after cleaning.
· Do not allow water used in cleaning to run through the drain
hole into the evaporation pan.
· Take care when cleaning the rear of the appliance. Sharp edges
can cut.
· An agent or qualified technician must carry out repairs if required.
Cleaning, Care & Maintenance
· Switch off and disconnect from the power supply before
Cleaning the Condenser
Periodically cleaning the condenser can extend the life of the
appliance. We recommend that our agent or qualified
technician clean the clean the condenser.
Troubleshooting
If your appliance develops a fault, please check the following table before making a call to your retailer.
Fault Probable Cause Action
The unit is not switch on Check the unit is plugged in correctly and switched on
Plug and lead are damaged Call your agent or qualified technician
The appliance is not working
Fuse in the plug has blown Replace the fuse
Power supply Check power supply
Internal wiring fault Call your agent or qualified technician
The appliance turns on, but
high/low.
T
water
Too much ice on the evaporator Defrost the appliance
Condenser blocked with dust Call your agent or qualified technician
Doors are not shut properly Check doors are shut, and seals are not damaged
Move the refrigerator to a more suitable location
interrupted
Ambient temperature is too high Increase ventilation or move appliance to a cooler position
Unsuitable foodstuffs are being stored in
the appliance
Appliance is overloaded Reduce the amount of food stored in the appliance
The appliance is not properly levelled Adjust the screw feet to level the appliance (If applicable)
The discharge outside is blocked Clear the discharge outlet
obstructed
Remove any excessive hot foodstuffs or blockages to the fan
Clear the floor of the appliance (if applicable)
T
loud
The water container is damaged Call your agent or qualified technician
The drip tray is overflowing Empty the drip tray (if applicable)
Loose nut/screw Check and tighten all nuts and screws
The appliance has not been installed in a
level or stable position
Page 3
Check installation position and change if necessary
Page 4
Technical Specifications
BZ-BCC1PREPXX
R600a
120
0.8
37
BZ-BCC1XX
R600a
120
0.8
37
240V/50Hz
BZ-BCC2-4DXX
220
R600a
170
1.2
2～8℃
850x900x700
75
BZ-BCC2-GR-TOPXX
R600a
170
1.2
850x900x700
75
BZ-BSP2XX
R600a
170
1.2
876x900x700
69
240V/50Hz
BZ-BCC3XX
R290
240
1.6
850x1365x700
110
BZ-BCC3-6DXX
R290
240
1.6
850x1365x700
110
BZ-BSP3XX
220
R290
240
1.6
2～8℃
876x1365x700
115
BZ-BPD3XX
R290
240
1.6
876x1365x700
115
BZ-BCC3ENXX
R290
240
1.6
970x1365x700
115
Model Voltage Gas
type
220～
240V/50Hz
220～
240V/50Hz
BZ-BCC1-2DXX
BZ-BCC2XX
BZ-BCC2PREPGRANITEXX
BZ-BCC2ENXX
220～
240V/50Hz
220～
～
240V/50Hz
220～
240V/50Hz
220～
240V/50Hz
220～
240V/50Hz
220～
R600a 120 0.8
R600a 170 1.2
R600a 170 1.2
R600a 170 1.2
Power
(W)
Current
(A)
Temperature
Range
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
Dimensions
HxWxD(mm)
435x700x850
435x700x850
435x700x850
850x900x700 75
1075x900x700 106
970x900x700 69
Weight
(kg)
43
BZ-BPD2XX
BZ-BCC3PZBAXX
BZ-BCC3-GR-TOPXX
BZ-BCC3PREPGRANITEXX
220～
240V/50Hz
220～
240V/50Hz
220～
240V/50Hz
220～
240V/50Hz
220～
240V/50Hz
～
240V/50Hz
220～
240V/50Hz
220～
240V/50Hz
220～
240V/50Hz
R600a 170 1.2
R290 240 1.6
R290 240 1.6
R290 240 1.6
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
2～8℃
850x900x700 69
1020x1400x700 170
850x1365x700 110
1075x1365x700 166
Electrical Wiring
Appliances are supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13-amp fuse as standard. The plug is to be
connected to a suitable mains socket. Appliances are wired as follows:
·Live wire (coloured brown) to terminal marked L
·Neutral wire (coloured blue) to terminal marked N
·Earth wire (coloured green/yellow) to terminal marked E
All appliances must be earthed, using a dedicated earthing circuit.
Page 4
Page 5
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being
required they must be readily accessible.
R290 refrigerant is used for this equipment.
Caution!
Consult repair manual/owner ’s guide before attempting to install or service this product. All safety precautions must be followed. Dispose of
properly in accordance with federal or local regulations. Risk of fire or explosion due to puncture of refrigerant tubing. Follow handling
instructions carefully.
Danger!
Risk of fire or explosion. Flammable refrigerant used. To be repaired only by trained service personnel. Do not use mechanical devices to defrost
refrigerator. Do not puncture refrigerant tubing.
Disposal
EU regulations require refrigeration product to be disposed of by specialist companies who remove or recycle all glasses,
metal and plastic components.
Consult your local waste collection authority regarding disposal of your appliance. Local authorities are not obliged to
dispose of commercial refrigeration equipment but may be able to offer advice on how to dispose of the equipment locally.
All packaging materials should be disposed of in an environmentally friendly way.
The cardboard may be used as scrap paper. The protective foil and the foam cushions are CFD-free.
Do not allow children to play with the packaging and destroy plastic gags safely.
Environmental protection
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively support us in
conserving resources and protecting the environment by returning this appliance to the collection centers (if available).
Compliance
Parts have undergone strict product testing in order to comply with regulatory standards and specification set by
international, independent, and federal authorities.
Products have been approved to carry the following symbol:
Page 5
Loading...