Blink HQ Charger Instruction Manual

Download

Page 1

Instruction Manual

Blink HQ Charger

Charge on.

a CarCharging Company

Page 2

iii

Charge on.Charge on.

No part of the contents of this document may be reproduced or transmitted in any form or by any means without the express written permission of Blink Network,

by the manufacturer to be consistent with the described components; however, inconsistencies sometimes occur. Such inconsistencies should be brought to the attention of an Blink Network, LLC representative. Changes to this manual may be made at any time without notice.

Disclaimer of Consequential Damages

Blink Network, LLC is not responsible for the use or application by any person of the materials in this manual. Blink Network, LLC is not responsible for damages, either direct or consequential, arising out of or relating to the use or application of these materials.

Blink, Blink Network, and the Blink logo are registered trademarks of Blink Network, LLC

SAE J1772™ is a trademark of SAE International

Blink Network, LLC 430 S. 2nd Avenue Phoenix, Arizona 85003-2418

1-888-998-BLINK www.blinknetwork.com

Table of Contents

Important Instructions ......................................................... 1

Introduction ........................................................................ 3

1.1 Product View .................................................................................................. 4

2 ...................................................................... 5

2.1 ...................................................................................... 5

3 Installation ......................................................................... 7

3.1 Before Installation ............................................................................................ 7

3.1.1 Safety Check ........................................................................................ 7

3.1.2 Grounding Instructions ...........................................................................7

3.2 Tools & Parts Required for Installation ................................................................7

3.3 Install the Charger ........................................................................................... 8

4 Operations ....................................................................... 13

4.1 About the Charger ........................................................................................13

4.1.1 Power ON/OFF Switch ........................................................................ 13

4.1.2 Charging Status Indicators .................................................................... 13

4.2 Delay Timer Indicator Flow ............................................................................. 14

4.3 Charging an Electric Vehicle (EV) .................................................................... 15

4.3.1 Interrupt Charging ............................................................................... 18

4.3.2 Auto Restart ........................................................................................ 18

4.3.3 Power Outage Recovery ....................................................................... 19

4.4 Troubleshooting ............................................................................................19

4.5 General Care ............................................................................................... 20

Federal Communications Commission (FCC) Regulatory Statements and Notices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Notice:

party responsible for compliance could void the user’s authority to operate the equipment.

LLC. The contents of this document have been veried

Page 3

Charge on.Charge on.

Save These Important Instructions

Before using the Blink Network, LLC (Blink) electric vehicle supply equipment (EVSE) Blink Charger, read all of these instructions, as well as the WARNING and CAUTION

markings in this document, on the Blink Charger,

and on your electric vehicle (EV).

Consult the following symbols and related instructions for the actions necessary to avoid hazards.

Safety Instructions

Instructions Pertaining to a Risk of Fire or Electric Shock.

Legend

WARNING: Used when there is a risk of personal injury

WARNING: RISK OF ELECTRIC SHOCK – Used when there is a risk of electric shock

WARNING: RISK OF FIRE

CAUTION: Used when there is a risk of damage to the equipment

• specifying a range of values or a nominal value of tightening torque to be applied to the clamping screws of the terminal connectors.

•

• Make sure that the materials used and the installation procedures follow local building codes and safety standards.

• The information provided in this manual in no way exempts the user of responsibility to follow all applicable codes or safety standards.

• Blink is not responsible for physical injury, damage to property or equipment caused by the installation of this device.

• This document provides instructions for the Blink Charger and should not be used for any other product. Before installation or use of this product, review this manual carefully and consult with a licensed contractor, licensed electrician, or trained installation expert to make sure of compliance with local building codes and safety standards.

• The Ø symbol (or phi symbol) represents the word “phase”. Phase or Ø can be used interchangeably.

List of Figures

Figure 1-1. Product View ....................................................................................................4

Figure 3-1. Mounting Bracket .............................................................................................8

Figure 3-2. Prepare for Wiring ............................................................................................9

Figure 3-3. Wiring ..........................................................................................................10

Figure 3-4. Blink Charger and Mounting Bracket .................................................................10

Figure 3-5. Mounting Bracket Screws .................................................................................11

Figure 3-6. Blink Charger and Charger Plug .......................................................................12

Figure 4-1. Remove the Charging Plug from the Charger ......................................................15

Figure 4-2. Connect the Charging Plug to the EV .................................................................15

Figure 4-3. Set the Delay Timer.... .....................................................................................16

Figure 4-4. Delay Timer Indicators .....................................................................................16

Figure 4-5. Press the Stop Button .......................................................................................17

Figure 4-6. Remove the Charging Plug from the EV..............................................................17

Figure 4-7. Place the Charging Plug into the Charger Holster

...............................................18

List of Tables

.........................................................................................5

.........................................................................6

Table 3-2. Tools & Parts Required for Installation ...................................................................7

Table 4-1. Charging Status Indictors ..................................................................................13

Table 4-2. Delay Timer Status Indicator ..............................................................................14

Page 4

Charge on.Charge on.

WARNING: RISK OF ELECTRIC SHOCK

Basic precautions should always be followed when using electrical products, including the following:

• Read all the instructions before using this product.

• This device should be super vised when used around children.

• Do not put ngers into the EV connector.

• Do not use this product if the exible power cord or EV cable is frayed, has broken insulation, or any

other signs of damage.

• Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.

WARNING: RISK OF ELECTRIC SHOCK

Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualied electrician or serviceman if you are in doubt as to whether the product is properly grounded.

WARNING: RISK OF ELECTRIC SHOCK

• Do not touch live electrical parts.

• Incorrect connections may cause electric shock.

WARNING: This equipment is intended only for charging vehicles that do not require ventilation during

charging. Please refer to your vehicle’s owner’s manual to determine ventilation requirements.

WARNING: Do not use extender cables to increase the length of the charging cable. Maximum length

is limited to 25 feet by the National Fire Protection Agency.

WARNING: To reduce the risk of re, replace only with same type and ratings of fuse.

WARNING: To reduce the risk of re, connect only to a circuit provided with 40 amperes maximum

branch circuit overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70.

General Conventions

Note: Indicates additional information that is relevant to the current process or procedure.

1 Introduction

This Instruction Manual describes how to properly install the Blink Model HQ EVSE Charger, referred to as the “Blink Charger” throughout this document. Contact the Blink Support Center at 1-888-998-BLINK for troubleshooting and more detailed technical questions.

• Unauthorized modication to the Blink equipment voids the manufacturer’s warranty.

The Blink Level 2 EVSE Charger specied in this document is designed for the U.S. market to charge plug-in electric vehicles (PEVs) and battery electric vehicles (BEVs). It provides AC Level 2 charging that effectively shortens charging times for typical EVs, when compared to a Level 1 cordset EVSE unit.

Page 5

Charge on.Charge on.

1.1 Product View

2 Specications

2.1 Product Specications

Table 2-1. Product Specications

Model HQ Specication

Power Input

Input Rating 208-240 VAC, single phase, 30 A maximum, 60 Hz

Connections & Wiring L1, L2, and Ground, hardwired w/ terminal block

Standby Power < 5 W

Power Output

Output Rating

208-240 VAC, single phase, 30 A maximum, 60 Hz, 7.2 kW maximum

Cold-Load Pickup

Randomized delay before charge resume after power failure

Protection

Internal Residual Current Detection

20 mA CCID per UL 2231

Upstream Breaker

2-pole 40 A breaker on dedicated circuit, non-GFCI

type

Plug-Out Protection

Power output is terminated upon detection of charging connector plug-out

Electrical Protection

Over Current, Short Circuit, Over Voltage, Under Voltage, Ground Fault, Surge Protection, Over temperature

User Interface & Control

Status Indicators

Standby (green), Charging (ashing green), Fault (red), Warning (ashing red)

Buttons/Switches Charger On/Off, Stop Charging, Delay Timer

Delay Timer Delay charging for 2, 4, 6, or 8 hours, adjustable

Environmental

Operating Temperature Storage Temperature

-22°F to 122°F (-30°C to 50°C)

-40°F to 176°F (-40°C to 80°C)

Humidity 95% relative humidity, non-condensing

Figure 1-1. Front View

Page 6

Charge on.Charge on.

Model HQ

Mechanical

Charging Cable Length 18 ft (5.5 m), straight cable

Ingress Protection Type 3R

Mounting Type Wall-Mount

Cooling Natural cooling

Dimension (W x H x D)

13.8 x 15.7 x 5.0 inch (350 x 400 x 126 mm), excluding charging cable, support bracket and cable holder

Net Weight 15.4 lb (7 kg)

Regulation

Charging Interface SAE J1772 compliant charging plug

Accessibility

such that the height of the storage means for the coupling device is located between 24 inches (600 mm) and 4 feet (1.2 m) from grade per NEC Article 625.

3 Installation

3.1 Before Installation

3.1.1 Safety Check

CAUTION: DISCONNECT ELECTRICAL POWER PRIOR TO INSTALLING THE BLINK CHARGER. FAILURE

TO DO SO MAY CAUSE PHYSICAL INJURY OR DAMAGE TO THE ELECTRICAL SYSTEM AND BLINK CHARGING UNIT.

The Blink Charger should be installed only by a licensed contractor, and/or a licensed electrician in accordance with all applicable state, local and national electrical codes and standards.

Before installing the Blink Charger, review this manual carefully and consult with a licensed contractor, licensed electrician and trained installation expert to ensure compliance with local building practices, climate conditions, safety standards, and state a

nd local codes.

Use appropriate protection when connecting to the main power distribution cable. Use tools as outlined in the section “Tools Required for Installation”.

3.1.2 GROUNDING INSTRUCTIONS

This product must be connected to a grounded, metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.

3.2 Tools & Parts Required for Installation

Table 3-2. Tools & Parts Required for Installation

Tool Size Supplier

EVSE Mounting Bracket N/A Blink

Torx Bolts (3 each) - used to secure the EVSE to the mounting bracket

T30 Blink

Cable hanger bracket N/A Blink

Conduit – used for power wire 1” Commercially available

Screws (2 each) – used to secure the main body mounting bracket on the wall

#10 x 2.5” Wood Screws, Countersunk Phillips Head

Commercially available

Torx Driver T30 Commercially available

Torque Wrench N/A Commercially available

Screws, wood (if required) No. 8 Commercially available

Bolts (for masonry) 1/4”, expansion Commercially available

Wire, Copper No. 8 AWG, 75°C or 90°C Commercially available

Page 7

Charge on.Charge on.

Figure 3-2. Prepare for Wiring

1. Connect the electrical wiring to the Blink Charger.

a. Choose the appropriate conduit in accordance with all applicable state, local and national electri-

cal codes and standards.

b. Use No. 8 AWG, 75°C or 90°C copper wire with Listed pressure terminal connectors, such as

ring and fork types, on the end of the conductor before attachment to the terminal blocks and

17.7 lb-in Torque force when connecting to Input terminal block.

3.3 Install the Charger

1. Drill bolt holes in the wall for the mounting bracket and the cable hanger.

Note: Follow applicable accessibility requirements for the mounting position. The unit shall be mounted at a sufcient height from grade such that the height of the storage means for the coupling device is located between 24 inches (600 mm) and 4 feet (1.2 m) from grade per NEC Article 625.

Masonry Walls Sheet Rock and Wood Stud Walls

Figure 3-1. Mounting Bracket

2. Secure the main body mounting bracket and the cable hanger bracket to the wall with appropriate bolts, as follows:

a. For masonry walls, use ¼” expansion bolts.

b. For nished walls supported by wood studs, use #10 x 2.5” Countersunk Phillips Head Wood

Screws.

c. Attach cable hanger to wall below mounting bracket with appropriate screws or anchors.

Page 8

Charge on.Charge on.

Figure 3-3. Wiring

4. Align the screw holes of the mounting bracket with the Blink charger holes.

Figure 3-4. Blink Charger and Mounting Bracket

5. Install and secure with three screws to the mounting bracket.

Figure 3-5. Mounting Bracket Screws

PE L2 L1

Page 9

Charge on.Charge on.

Figure 3-6. Blink Charger and Charger Plug

4 Operations

4.1 About the Charger

4.1.1 Power ON/OFF Switch

There is an ON/OFF switch located on the side of the Blink Charger. If the Blink Charger is expected not to be used for a long period of time, turn OFF the Blink Charger. Turn ON the Blink Charger before use.

4.1.2 Charging Status Indicators

Table 4-1. Charging Status Indicators

FRONT PANEL

LED BEHAVIOR

DESCRIPTION

DEFINITION

Not illuminated

Charger is powered OFF. Use the “Power ON/OFF” switch to power ON the Charger.

Green

Charger is powered ON and ready for charging.

Flashing green Charging in process.

Red

Charger malfunction. Stop using immediately.

Flashing red

Charger is recovering from a minor fault such as OVP, UVP, OTP, OCP. Wait until the indicator turns green to resume charging.

6. Secure the charger plug to the charger and place the charger cable on the cable hanger.

Page 10

Charge on.Charge on.

4.3 Charging an Electric Vehicle (EV)

1. Turn ON the Blink Charger power switch.

2. Release the charging plug from the charger holster.

Figure 4-1. Remove the Charging Plug from the Charger Holster

Figure 4-2. Connect the Charging Plug to the EV

3. Set the delay timer by pressing the Delay Timer button once for each 2 hour interval, then connect the charging plug to the EV.

4.2 Delay Timer Indicator Flow

Table 4-2. Delay Timer Status Indicator

FRONT PANEL DELAY TIMER

LED BEHAVIOR

DESCRIPTION

DEFINITION

2HR 4HR 6HR 8HR

4 LEDs OFF Delay Timer is not enabled.

2HR 4HR 6HR 8HR

Charger is ready and the delay timer can be set.

2HR 4HR 6HR 8HR

2HR LED solid ON Delay Timer is set to 2 hours

2HR 4HR 6HR 8HR

2HR and 4HR LEDs solid ON

Delay Timer is set to 4 hours

2HR 4HR 6HR 8HR

2HR, 4HR, and

6HR LEDs solid ON

Delay Timer is set to 6 hours

2HR

4HR 6HR 8HR

2HR, 4HR, 6HR, and 8HR LEDs solid ON

Delay Timer is set to 8 hours

2HR

4HR 6HR 8HR

Delay charging is enabled. Current delay time is less than 2 hours.

2HR 4HR 6HR 8HR

2HR LED solid on and 4HR

Delay charging is enabled. Current delay time is 2 - 4 hours.

2HR 4HR 6HR 8HR

2HR and 4HR LEDs solid

Delay charging is enabled. Current delay time is 4 - 6 hours.

2HR 4HR 6HR 8HR

2HR, 4HR, and 6HR LEDs Delay charging is enabled. Current

delay time is 6 - 8 hours.

Page 11

Charge on.Charge on.

Note: Refer to Table 4-2 for more information about the Delay Timer functionality.

4. If the delay timer is set, charging starts after timer expires. Other wise, charging starts immediately.

Figure 4-3. Set the Delay Timer

5. Disconnect the charging plug from the EV or press the “STOP” button to stop charging before the charge is complete.

6. Reconnect the charging plug to start charging again. Refer to Step 2 of this Section.

Figure 4-5. Press the Stop Button

7. When charging is complete, disconnect the charging plug from the EV and place it in the charger holster.

Figure 4-6. Remove the Charging Plug from the EV

Figure 4-4. Delay Timer Indicators

Page 12

Charge on.Charge on.

Figure 4-7. Place the Charging Plug into the Charger Holster

4.3.1 Interrupt Charging

There are two ways to interrupt a charging session at any time:

1. Disconnect the charging plug from the EV and return it to the charger holster.

2. Press the STOP button on the front panel of the Blink Charger. The charging plug will need to be disconnected and reconnected to start charging again.

To resume charging after a user-initiated charge interruption, follow normal procedures to initiate charging again.

4.3.2 Auto Restart

When a charging session is interrupted due to a temporary error condition, the Blink Charger will automatically restart charging when the cause of the temporary error condition returns to normal. Status indicator lights remain ashing RED until the error condition is resolved.

• Temporary error conditions include: Over Current, Over Voltage, Under Voltage, Over Temperature.

• For Over Current conditions: The charger will tr y to automatically restart two times for each

charging session.

• When a charging session is interrupted due to a CCID trip, the Blink Charger will tr y to restart after

10 minutes.

4.3.3 Power Outage Recovery

When power resumes after an outage, the Blink Charger restarts automatically with a delay ranging from 10 to 100 seconds. The delay is designed to avoid impacting the utility grid when multiple chargers are in the same area attempting to resume charging simultaneously.

SITUATION

ACTION

Status indicator does not turn

1. Make sure the power input is connected correctly

2. Turn the Blink HQ charger power OFF then back ON

3. If the problem persists, contact Customer Support

Status indicator does not blink

when the charger is connected

to the EV

1. Check if the delay timer is activated. If the delay timer is activated (counting down), the charging session will start when the delay timer expires. As soon as a charging session starts, the status indicator will start to ash in green.

2. Disconnect the charging plug and reconnect it securely to the receptacle on the EV.

3. Inspect the cable and plug for damage

4. Inspect the EV and its receptacle for damage

5. Try to charge with the portable cord set that came with the vehicle

6. If the charge starts, contact Blink Customer Support

7. If the charge doesn’t start, contact EV Customer Service

Status indicator blinks red while

charging

1. There is a temporary error

2. Wait until the temporary error is resolved and the Charger returns to normal condition. It usually takes less than 10 seconds.

3. If the status indicator doesn’t return to green, turn OFF the charger and then back ON using the ON/OFF switch

4. If the situation persists, contact Customer Support

4.4 Troubleshooting

If an error message is displayed during the charging process, follow the associated instructions out- lined in the troubleshooting table.

Page 13

Charge on.

SITUATION

Status indicator is in solid red

Cannot set delay timer

ACTION

1. There is a critical error (CCID trip or Relay failure)

2. Unplug the charging connector

3. Turn the Blink HQ charger power OFF then back ON

4. If the situation persists, contact Customer support

1. Delay timer can only be set when the charger is in Standby state and the status indicator is solid green

2. Once the charger is in Charging state (and the status indicator is in blinking green), the delay timer button is disabled

3. Stop the ongoing charging session by pressing the STOP button

4. Unplug the charging connector

5. Wait until the status indicator turns solid green

6. Press Delay timer button to set delay timer

7. Connect charger to the EV

8. Delay timer will start to count down

4.5 General Care

The exterior of the Charger is designed to be rainproof. To ensure proper maintenance of the charger, follow these guidelines:

• Despite the water resistance of the enclosure, when cleaning it is preferred to not direct streams of water at the unit. Clean with a soft, damp cloth.

• Make sure the charging plug is put back in the holster after charging to avoid damage.

• Ensure the power cable is stored on the cable hanger after use to avoid damage.

• If the power cable or the charging plug is damaged contact Customer Support..