Page 1
REPLACEMENT PARTS:
In the event that replacement parts are ever needed, please call
1-888-633-7840. Please provide your original order number and a
description of the part needed.
ONE YEAR LIMITED WARRANTY:
What is covered by this warranty and for how long:
For a period of one (1) year from the date of purchase, all products are
warranted against defects in materials and workmanship provided that the
product is installed according to the product instructions. We reserve the
right to determine if your piece warrants a repair or partial replacement
of any parts or in the unlikely event the entire piece is defective, we will
replace this window covering with a new window covering of equal or
superior value. This shall be your sole remedy under this warranty.
Who is covered by this warranty:
This warranty applies to the original customer with proof of purchase in
a residential application within the United States.
What is not covered in this warranty:
This warranty does not cover removal or installation or reinstallation of any
window covering. This warranty does not cover damage or defects caused
by or resulting from improper maintenance, neglect or improper use,
abuse, misuse, neglect, accidents, Acts of God, alteration, commercial use,
installation, removal or reinstallation or exposure to excessive moisture.
Your rights under State Law:
This warranty gives you the specific legal rights. You may also have other
rights which may vary from state to state. Blindschalet.com will not be
liable for INCIDENTAL OR CONSEQUENTIAL DAMAGES or for any other
direct or indirect damage, loss, cost, expense or fee. Some states do
not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
How to obtain warrant service:
To obtain warranty service please contact Customer Service at
1-888-633-7840 or via e-mail at customerservice@blindschalet.com.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER
OBLIGATIONS, LIABILITIES, OR WARRANTIES.
1-888-633-7840
Tavarua Roman Shade
Installation Instructions
Thank you for purchasing your custom Tavarua window shade. With proper
installation, your shade should look beautiful and provide years of service.
Please check all parts and read these instructions, before starting installation.
MOUNTING HARDWARE KIT INCLUDES:
Mounting Bracket with Wing Nut
Width of Shade Qty
18˝ to 42˝ 2
42 1/8˝ to 84˝ 3
84 1/8˝ to 96˝ 4
Bracket Screw – 1 inch
Width of Shade Qty
18˝ to 42˝ 4
42 1/8˝ to 84˝ 6
84 1/8˝ to 96˝ 8
Cord Cleat and Screws: Provided with all standard
cord lock shades. All cords should be secured
with cord cleats to prevent the risk of strangulation.
Keep cords away from children and pets.
Clutch Control Shades: Shades with clutch
controls come with a continuous cord loop and
are supplied with a cord tensioner, which should
always be screwed to the wall. Always secure cord
loops to prevent the risk of strangulation. Keep
cord loops away from children and pets.
Page 2
TOOLS THAT MAY BE REQUIRED:
Pencil, Tape Measure, Screw Driver, Step Stool, Level, and Drill
INSTALLATION:
NOTE: For wallboard or plaster, use anchors designed for hollow walls
(not included). For concrete, stone and brick, use a masonry drill bit and
anchors designed for masonry (not included).
FOR OUTSIDE OR WALL MOUNT:
1. Position brackets 1 to 2 inches from the end
of the head rail. If provided, position middle
brackets to align with pre-drilled holes
in the head rail.
2. Hold the shade in place and mark the
desired bracket locations with a pencil.
Use a level to ensure the brackets are straight.
3. Pre-drill the mounting holes into the
mounting surface. Next, screw the
brackets in place into the mounting
surface. [figure 1]
4. Hold the shade so that the screw posts
on the brackets fit through the slots in
the head rail and re-attach wing nuts and
screw tight to hold the head rail firmly.
Make sure the shade is level. [figure 2]
[figure 1]
head rail
FOR INSIDE OR CEILING MOUNT:
1. Position brackets approximately 1 inch from the
ends of the head rail. If provided, position middle
brackets to align with pre-drilled holes in the
head rail.
2. Measure 1 inch in from each side of the
window frame and mark bracket locations
with a pencil.
3. Pre-drill the mounting holes into the mounting
surface. Next, screw the brackets in place into
the mounting surface. [figure 3]
4. Hold the shade so that the screw posts on the
brackets fit through the slots in the head rail
and re-attach wing nuts and screw tight to hold
the head rail firmly. Make sure the shade is level.
[figure 2]
INSTALLING THE CORD CLEAT:
Optional. Your shade is fitted with a cord lock,
which allows the shade to stay in whatever
position you desire. However cord cleats help
keep cords tidy and away from children. We
strongly recommend the use of cord cleats
to help prevent the risk of strangulation.
1. Find a convenient place about 1 inch out from
the side of the shade where the cords are
located and about one quarter of the way
up from the bottom of the shade.
[figure 3]
[figure 2]
2. Hold the cord cleat parallel with the frame of
the window. With a pencil, make a mark through
the holes.
3. Make pilot holes and install cord cleat with
2 screws.
Loading...