Blendtec ez Blender Operation Manual

operations manual

BRAWN. BRAINS. BLENDTEC.™

ez Blender

Page 1

Table Of Contents

Section Page

Section 1 .....Important Safeguards 2

Section 2.....Component Overview 4

Section 3.....Unpacking 6

Section 4.....Installation 7

Section 5.....Operating Instructions 8

Section 6.....Warranty and Service 12

Page 2

SECTION 1 – IMPORTANT SAFEGUARDS

Read all instructions carefully before using your Blendtec machine.

1.1 SAFETY CERTIFICATION

The ez Blender and accessories are certied by
ETL to UL standard 763 and by CE Standards.

1.2 HEALTH CERTIFICATION

The ez Blender and accessories are certied by

NSF International.

1.3 AVOID CONTACT WITH MOVING PARTS

● Keep ngers, hands, hair and clothing away from all moving parts.

● Keep all utensils away from the drive socket and blender blades during
operation. Metal utensils will damage blades.

● NEVER put hands into blender jar or add substances by hand when
blender is operating.

● NEVER place jar into drive socket if blender motor is operating.

● Do not rock the blender when it is operating. Keep the blender jar

straight up until the operation is complete.

● These precautions will prevent personal injury and/or damage to the
blender.

1.4 POWER CORD PRECAUTIONS

● Do not operate with a damaged cord or plug.

● If the supply cord is damaged, it must be replaced by the manufacturer

or its service agent in order to avoid a hazard.

● Do not let the cord hang over the edge of the work surface.

● Never use an extension cord with the unit.

● Unplug the blender motor before changing blender locations or

cleaning.

1.5 NEVER ATTEMPT TO REPAIR THE POWER UNIT

Never remove the blender base cover. The blender base does not
contain self-adjustable or serviceable parts. All service and adjustments
must be made by a qualied service agent. Removing the cover or

attempting to service the blender will void the warranty.

1.6 TURN THE UNIT OFF WHEN NOT IN USE

R

Page 3

1.7 THE 110/120 VOLT RECEPTACLE FOR EACH POWER UNIT MUST BE

PROTECTED BY A SEPARATE 15 AMP CIRCUIT BREAKER OR FUSE.

Do not use any other electrical equipment on the same circuit as
the blender or you risk overloading the circuit and either damaging
the blender electronics or blowing the circuit protection.

1.8 NEVER OPERATE IF THE UNIT APPEARS DAMAGED

If the blender malfunctions call the service agent rst. If it is dropped
or damaged in any way, return the blender to a Blendtec service agent
immediately for examination, repair, electrical or mechanical adjustment,
or possible replacement.

1.9 NEVER OPERATE IN LIQUID

Do not operate the blender motor in water or any other liquid. Avoid
any contact between the motor and water. Deliberate use of machine

outdoors in conditions where precipitation is present will void the
warranty.

1.10 NEVER PUT ITEMS SUCH AS METAL, ROCKS, OR OTHER
HARD MATERIALS INTO BLENDER JAR

Metal utensils and other hard materials are dangerous. They can cause

injury or damage. Damage caused by such foreign objects will void the

warranty.

1.11 NEVER OPERATE USING ATTACHMENTS NOT SOLD BY
BLENDTEC

The use of unauthorized attachments voids the warranty and may cause

re, electric shock, or injury.

1.12 ALWAYS SECURE THE BLENDER LID BEFORE STARTING THE
MACHINE

Even if you have a sound enclosure, make sure you place a lid on the
blender jar before you close the cover.

1.13 AVOID TOUCHING THE METAL BASE AFTER EXTENSIVE USE

The metal base of the blender may become hot after numerous cycles.

1.14 BLADES ARE SHARP! HANDLE CAREFULLY

1.15 When blending HOT LIQUIDS, remove center plug of lid.

SAVE THESE INSTRUCTIONS