Page 1
TIRE PRESSURE
MONITORING SYSTEM
TPMS 1.0
Operating & Installation Instructions
Page 2
SPECIFICATION
Sensor
Operating frequency
Battery voltage
Battery lifetime
Operating temperature
Pressure range
Display
Operating frequency
Operating voltage
Operating temperature
Default value
High pressure value
Low pressure value
High temperature value
Precision
Temperature
Pressure
Air pressure unit
Accessories
433.92MHz
1.8V ~ 3.3V
1-year
-20°C ~ 60°C
0~3.5 Bar / 0~50 PSI
433.92MHz
12 +/- 3V
-20°C ~ 70°C
3.0 Bar / 43 PSI
1.8 Bar / 26 PSI
68°C ~ 80°C
+/-2°C
0.1 Bar / 1.5 PSI
1 Bar = 14.5 PSI = 100 Kpa = 1.02Kgf/cm2
4x external sensor 5x anti-theft nuts
1x spanner
(Keep in car)
1x sensor tool 1x battery
4x rubber seal
1
Page 3
DISPLAY
Set Button
Cigarette Plug
Data Display
Warning Display
Pressure Unit
SENSOR
Sensor Cover
Battery
Sensor
Rubber Seal
Washer
Hex Nut
2
Page 4
3
Page 5
4
Page 6
After entering the setting interface, press setting button “ ”
for high pressure value setting, the rst number will ash, then
press the right button“ ” to adjust the number.
When nish adjusting the number, press setting button to
conrm, you will hear the sound ‘Bi-’ to indicate high pressure
value is successfully set.
SETTING
5
When nish adjusting the number, press setting button to
conrm, you will hear the sound ‘Bi-’ to indicate low pressure
value is successfully set.
After entering the setting interface, press the right button “ ”
twice then press the setting button“ ”, the rst number will ash,
then press the right button “ ” to adjust the number.
When nish adjusting the number, press setting button to
conrm, you will hear the sound ‘Bi-’ to indicate high temperature
value is successfully set.
HIGH PRESSURE VALUE SETTING
Press & hold setting button “ ”.
Press & hold setting button “ ”.
Press & hold setting button “ ”.
Press & hold setting button “ ”.
LOW PRESSURE VALUE SETTING
After entering the setting interface, press the right button “ ”,
then press the setting button “ ”, the rst number will ash,
then press the right button “ ” to adjust the number.
HIGH TEMPERATURE VALUE SETTING UNIT SWITCHING
After entering the setting interface, press the right button “ ”
3 times then press the setting button, the unit of Bar and Psi will
switch.
You will hear the sound ‘Bi-’ to indicate that unit switching successful
Psi
RESET SETTING
Press & hold the right button “ ” for at least 5 seconds.
You will hear the sound ‘Bi--’which indicates that all parameters
setting has returned to original factory settings.
Page 7
SETTING
TROUBLESHOOTING
1. Air leakage after sensor installation
The tire valves may not be universal standard, please check with the local workshop.
2. No tire data are displayed after completing installation
Ensure ACC is turned on.
3. Missing/lost sensor
Please purchase new sensor.
4. Sensor battery low
Please replace with battery CR1632.
5. Change of tire location
Please reprogram the corresponding sensors.
Note
1.
2.
3.
4.
5.
6.
TPMS (Tire Pressure Monitoring System) is designed for monitoring tire irregularities.
Drive has responsibility to maintain tires regularly.
Driver should react promptly once warning from this unit alerted.
Blaupunkt does not guarantee or assumes liability for the loss of sensors.
All sensors in this unit have been pre-set individually for each tire in the factory.
Whenever the location of tire changed, the sensor must be reprogrammed.
The display will turn o whenever the car is turned o.
6
(Sensor pairing are required only when the tires or
the sensors has switched location or be replaced)
SENSOR PAIRING
Press “ ” and “ ” simultaneously for at least 5 seconds to enter
into pairing mode. Pairing order : Left Front Right Front
Left Rear Right Rear.
When system receives the signal, you will hear “Bi- Bi- Bi-” which
indicates successful sensor pairing.
Every time display ashes the next location, repeat steps 3-4 to
pair the rest of the sensors.
After the last tire (right rear) is paired with the sensor, the display
will return to the original interface.
Left front tire icon begin to ash.
Immediately get the sensor to learn the code and wait for
5-8 seconds.
Unscrew the sensor
Page 8
Designed and engineered by Blaupunkt 1 311 18 001 23 01
Loading...