Page 1
WARRANTY
This product has 3 years warranty for manufacturing defects. The warranty period
will be counted from the date of purchase of the product, according to purchase
invoice. Product warranty only covers manufacturing defects, defects resulting from
improper use, such as dropping, improper transportation, connection to the mains
power supply not in compliance with the voltage specied in this manual, insertion
of foreign objects and natural wear of parts and parts Such as plastic parts (caps,
buttons, handles, latch locks, power cables, etc.) and metal parts (wires, motors, etc.).
Also not covered are damages due to agents of nature, lightning, ood, sea,
oxidation, humidity etc.). The product will lose its warranty if it presents defects,
which after analysis by our technicians, are characterised as being improperly used,
used for professional use or for the purpose for which it is not intended (according to
the Owner's Manual). This warranty will be void if it is found that the device has been
tampered with, has been repaired by a person or service not authorized by
Blaupunkt. The guarantee is only valid with the receipt/invoice provided at purchase.
Blaupunkt undertakes to provide the above-mentioned services in the warranty
period only in places where it maintains an authorised service. Consumers who are
not located near an authorised service centre should be responsible for the costs and
risks of transport to the authorized service of their choice.
Natural wear is not covered under warranty.
This product is for domestic use only.
Lawn Mower GX4000
INSTRUCTION MANUAL
To prevent injury or damage, read
and follow all instructions in this
manual before using the appliance.
SAVE THESE INSTRUCTIONS
Imported and Distributed by SKN Innovations Ltd. for Blaupunkt
17 Northumberland Sq.
NE30 1PX
0800 677 1923
customerservice@bp-tools.co.uk
www.bp-tools.co.uk
Page 2
1
GENERAL SAFETY WARNINGS
WARNING: When using the product, the safety rules must be
followed. For your own safety and that of bystanders, please read
these instructions before operating the product. Please keep the
instructions safe for later use.
The product is capable of amputating hands and feet, and throwing
objects. Failure to observe all safety instructions could result in serious
injury or death. Be familiar with the controls and the correct use of the
product.
Never allow children or people with reduced physical, sensory or mental
capabilities or persons not familiar with these instructions to operate,
clean or maintain the product. Local regulations may restrict the age of
the operator. Children should be adequately supervised to ensure they do
not play with the product.
Stay alert, watch what you are doing, and use common sense when
operating the product. Do not operate the product while tired or under
while operating the product may result in serious personal injury.
Wear heavy, long trousers, long sleeves, sturdy anti-slip footwear. Do not
wear short trousers, sandals, or go barefoot. Avoid wearing clothing that is
Always wear safety glasses with side shields.
run.
Use the product across the face of slopes, never up and down. Exercise
extreme caution when changing direction on slopes.
or embankments. Poor footing could cause a slip and fall accident.
WORK AREA SAFETY
Never use product while people, especially children, or pets are within 15m
because of the danger of objects being thrown by contact with the
blade.
WORK AREA SAFETY
Objects struck by the lawn mower blade can cause severe injuries to
persons. Thoroughly inspect the area where the product is to be used and
remove all rocks, sticks, metal, wire, toys, or other foreign objects.
Remember, string or wire may entangle with the cutting means.
Do not operate the product in explosive atmospheres, such as in the
which may ignite the dust or fumes.
Do not operate the product in wet grass or in the rain.
Do not use the lawn mower when there is a risk of lightning.
Keep in mind that the operator or user is responsible for accidents or
hazards occurring to other people or their property.
Tragic accidents can occur if the operator is not alert to the presence of
children. Children are often attracted to the product and the mowing
activity. Never assume that children will remain where you last saw them.
Keep children out of the mowing area and under the watchful care of a
responsible adult other than the operator, be alert and turn the product
Use extra care when approaching blind corners, shrubs, trees, or other
objects including overhanging shrubs, which may block your view.
ELECTRICAL SAFETY
Power plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools.
position before plugging in the product to the power supply. Do not carry
Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose the product to rain or wet conditions.
Water entering an appliance will increase the risk of electric shock.
Electrical power should be supplied via a residual current device (RCD)
with a tripping current of not more than 30 mA.
2
WARNING: When using the product, the safety rules must be
followed. For your own safety and that of bystanders, please read
these instructions before operating the product. Please keep the
instructions safe for later use.
The product is capable of amputating hands and feet, and throwing
objects. Failure to observe all safety instructions could result in serious
injury or death.Be familiar with the controls and the correct use of the
product.
Never allow children or people with reduced physical, sensory or mental
capabilities or persons not familiar with these instructions to operate,
clean or maintain the product. Local regulations may restrict the age of
the operator. Children should be adequately supervised to ensure they do
not play with the product.
Stay alert,
watch what you are doing, and use common sense when
operating the product. Do not operate the product while tired or under
while operating the product may result in serious personal injury.
Wear heavy, long trousers, long sleeves, sturdy anti- slip footwear. Do not
wear short trousers, sandals, or go barefoot. Avoid wearing clothing that is
Always wear safety glasses with side shields.
run.
Use the product across the face of slopes, never up and down. Exercise
extreme caution when changing direction on slopes.
or embankments. Poor footing could cause a slip and fall accident.
WORK AREA SAFETY
Never use product while people, especially children, or pets are within 15
m because of the danger of objects being thrown by contact with the
blade.
Page 3
ELECTRICAL SAFETY
Before use check the supply and extension cord for signs of damage or
aging. If the cord becomes damaged during use, disconnect the cord from
the supply immediately. Do not touch the cord before disconnecting the
supply. Do not use the product if the cord is damaged or worn.
If you need to use an extension cord ensure it is suitable for outdoor use
it before every use for damage, always uncoil it during use because coiled
cords can overheat. Damaged extension cords should not be repaired,
they should be replaced with an equivalent type.
Make sure the power cord is positioned so that it cannot be damaged by
the cutting means and will not be stepped on, tripped over or otherwise
subjected to damage or stress.
Never pick up or carry the product by the electric cable.
Never pull by the power cord to disconnect from the power supply.
Keep the power cord away from heat, oil and sharp edges.
Make sure voltage is correct for your product. A nameplate on the product
indicates the product’s voltage. Never connect the product to an AC
Always ensure the cord from the handlebar to the mower body is never
trapped, pinched or otherwise damaged during assembly or handle
folding. Never apply power to the mower if this cable is damaged. Return
to authorised service centre for professional repair.
LAWN MOWER SAFETY WARNINGS
Before using, always visually inspect to ensure blades, blade bolts, and
cutter assembly are not worn or damaged.
Replace worn or damaged blades and bolts in sets to preserve balance.
The blade on the product is very sharp. Use extreme caution and wear
security.
Return to an authorised service centre to replace damaged or unreadable
labels.
Check all nuts, bolts, and screws at frequent intervals for proper tightness
to be sure the equipment is in safe working condition.
Check the grass box frequently for wear, holes or deterioration.
LAWN MOWER SAFETY WARNINGS
Replace worn or damaged parts before operating the product.
The mower must be started with the user behind the handlebars in the
operator safety zone. Never start the product if:
All four wheels are not on the ground
The grass discharge chute is exposed without being protected by either
the mulching plug and grass discharge chute cover or the grass box and
grass discharge chute cover.
Hands and feet of all persons are not clear of the cutting enclosure.
properly start and stop the product.
extremely dangerous.
Do not force the product. It will do the job better and safer at the speed for
which it was designed.
Stop the blade when crossing gravel surfaces.
Do not pull the product backward unless absolutely necessary. If you must
behind to avoid tripping or pulling the product over your feet.
Stop the motor and allow the blade to stop if the product has to be tilted
for transportation when crossing surfaces other than grass, and when
transporting the product to and from the area to be mowed.
Never use the product with defective guards or shields, or without safety
Do not tilt the product when switching on the motor or whilst the motor
is running. This exposes the blade and increases the probability of objects
being thrown.
Switch on the motor carefully according to instructions and keep hands
and feet away from cutting area. Do not put hands or feet near or under
rotating parts. Keep clear of the discharge opening at all times. Do not
start the product when standing in front of the discharge opening.
Never pick up or carry the product while it is running.
Stop the mower motor and disconnect from the power supply, make sure
that all moving parts have come to a complete stop for the below cases:
whenever you leave the product unattended (including disposal of grass
clippings).
3 4
Page 4
LAWN MOWER SAFETY WARNINGS
before cleaning a blockage or unclogging discharge chute
before checking, cleaning or working on the product
after striking a foreign object; inspect the product for damage and make
repairs as necessary before
restarting and operating the product.
before removing the grass box or opening the grass discharge chute
cover.
If the product starts to vibrate abnormally (check immediately)
-- inspect for damage, particularly the blades
-- replace or repair any damaged parts
-- check for and tighten any loose parts
Avoid holes, ruts, bumps, rocks, property stakes, or other hidden objects.
Uneven terrain could cause a slip and fall accident.
OVERLOAD PROTECTION DEVICE
The product has an overload protection device. When overloading is
detected, the product will automatically switch o. If the overload
protector is actuated, the motor must be allowed to cool down for 5 to
10 minutes.
Turn o the power and remove the plug from the supply. The blades are
sharp, wear heavy duty gloves before touching. Make sure the blade can
rotate freely and is not jammed or tight.
When the motor is cool, connect the plug to the power supply, turn the
power on. Press the Start button and then the On-o button to start the
product. If the product will still not start, return it to an authorised service
centre for repair.
INTENDED USE
The product is only intended for use outdoors.
The product is designed for domestic lawn mowing. The cutting blade
should rotate approximately parallel to the ground over which it is being
wheeled. All four wheels should touch the ground while mowing. It is a
pedestrian controlled walk behind mower designed to be pushed by
hand.
5 6
INTENDED USE
The product should never be operated with the wheels o the ground; it
should not be pulled or ridden on. It should not be used to cut anything
other than domestic grass lawns.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following hazards
may arise in use and the operator should pay special attention to avoid the
following:
Injury caused by vibration. Always use the right tool for the job, use
designated handles and restrict working time and exposure.
Exposure to noise can cause hearing injury. Wear ear protection and limit
exposure.
Contact with blades
Injury from thrown objects
TRANSPORTATION AND STORAGE
Stop the product and disconnect from the power supply, make sure that
all moving parts have come to a complete stop, and allow it to cool before
storing or transporting.
Clean all foreign material from the product. Store it in a cool dry and
well-ventilated place that is inaccessible to children. Keep away from
corrosive agents such as garden chemicals and de-icing salts. Do not
store outdoors.
For transportation, secure the product against movement or falling to
prevent injury to persons or damage to the product.
WARNING: Use extreme caution when lifting or tilting the
product for maintenance, cleaning, storage or transportation,
the blade is sharp, keep all body parts away from the blade whilst
it is exposed.
Page 5
The product has an overload protection device. When overloading is
detected, the product will automatically switch o. If the overload
protector is actuated, the motor must be allowed to cool down for 5 to
10 minutes.
Turn o the power and remove the plug from the supply. The blades are
sharp, wear heavy duty gloves before touching. Make sure the blade can
rotate freely and is not jammed or tight.
When the motor is cool, connect the plug to the power supply, turn the
power on. Press the Start button and then the On-o button to start the
product. If the product will still not start, return it to an authorised service
centre for repair.
INTENDED USE
The product is only intended for use outdoors.
The product is designed for domestic lawn mowing. The cutting blade
should rotate approximately parallel to the ground over which it is being
wheeled. All four wheels should touch the ground while mowing. It is a
pedestrian controlled walk behind mower designed to be pushed by
hand.
7 8
MAINTENANCE
WARNING: Use only original manufacturer’s replacement parts,
accessories and attachments. Failure to do so can cause injury,
poor performance and may void your warranty.
WARNING: Servicing requires extreme care and knowledge and
should be performed only by a qualied service technician. For
service we suggest you return the product to your nearest
authorised service centre for repair. When servicing, use only
identical replacement parts.
Stop the product and disconnect from the power supply, make sure that
all moving parts have come to a complete stop before any cleaning or
maintenance task. You may make adjustments and repairs described here.
For other repairs, contact the authorised service agent.
Check the grass box frequently for wear or deterioration.
After each use, clean the product with a soft dry cloth. Any part that is
damaged should be properly repaired or replaced by an authorised
service centre.
Check all nuts, bolts and screws at frequent intervals for proper tightness
to ensure the product is in safe working condition.
Be careful during adjustment of the product to prevent entrapment of the
ngers between moving blades and xed parts of the product.
When servicing the blades be aware that, even though the power source
is switched o, the blades can still be moved.
The blade on the product is very sharp. Use extreme caution and wear heavy
duty gloves when tting, replacing, cleaning or checking bolt security.
Replace damaged blades and bolts in sets to preserve balance.
RISK REDUCTION
It has been reported that vibrations from hand-held tools may contribute
to a condition called Raynaud’s Syndrome in certain individuals. Symptoms
may include tingling, numbness and blanching of ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to cold and
dampness, diet, smoking and work practices are all thought to contribute
to the development of the these symptoms. There are measures that can
be taken by the operator to possibly reduce the eects of vibration:
RISK REDUCTION
Keep your body warm in cold weather. When operating the unit wear
gloves to keep the hands and wrists warm. It is reported that cold
weather is a major factor contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately
discontinue use and see your doctor about these symptoms.
WARNING: Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods, ensure
you take regular breaks.
Page 6
KNOW YOUR PRODUCT
1 - Handle
2 - Start lever
3 - On/o button
4 - Power cord
5 - Motor control cable retainer
6 - Height adjustment lever
7 - Switch box
8 - Power cord retainer
9 - Grass box full indicator
10 - Grass box
11 - Rear wheel
12 - Front wheel
SYMBOLS ON THE PRODUCT
Read and understand all instructions before operating the
product, follow all warnings and safety instructions.
Wear ear protection and wear eye protection.
Do not operate on inclines greater than15°. Mow across the face
of slopes, never up and down.
Do not expose to rain or damp condition.
Beware of sharp blades. Blades continue to rotate after the motor
is switched o – Remove plug from mains before maintenance or
if cord is damaged.
Beware of throw of ying objects Keep all bystanders, especially
children and pets, at least 15m away from the operating area.
Keep the supply exible cord away from the cutting blades
Press and hold the safety button, squeeze the switch lever
towards the handle.
Go
STOP
Class II tool, double insulation
9 10
After each use, clean the product with a soft dry cloth. Any part that is
damaged should be properly repaired or replaced by an authorised
service centre.
Check all nuts, bolts and screws at frequent intervals for proper tightness
to ensure the product is in safe working condition.
Be careful during adjustment of the product to prevent entrapment of the
ngers between moving blades and xed parts of the product.
When servicing the blades be aware that, even though the power source
is switched o, the blades can still be moved.
The blade on the product is very sharp. Use extreme caution and wear heavy
duty gloves when tting, replacing, cleaning or checking bolt security.
Replace damaged blades and bolts in sets to preserve balance.
RISK REDUCTION
It has been reported that vibrations from hand-held tools may contribute
to a condition called Raynaud’s Syndrome in certain individuals. Symptoms
may include tingling, numbness and blanching of ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to cold and
dampness, diet, smoking and work practices are all thought to contribute
to the development of the these symptoms. There are measures that can
be taken by the operator to possibly reduce the eects of vibration:
Page 7
SYMBOLS ON THE PRODUCT
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Conforms to all regulatory standards in the country in the EU
where the product in purchased
The following signal words and meanings are intended to explain the
levels of risk associated with this product:
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SYMBOLS IN THIS MANUAL
Connect to power outlet.
Disconnect from power outlet.
Parts or accessories sold separately
11 12
SYMBOLS IN THIS MANUAL
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Keep hands away from blades
Note
Warning
Stop the product.
GENERAL MOWING TIPS
When cutting long grass, reduce walking speed to allow for more eective
cutting and a proper discharge of the clippings.
Do not cut wet grass; it will stick to the underside of the deck and prevent
proper collection or discharge of grass clippings.
New or thick grass may require a higher cutting height.
If you wish to collect the grass cuttings for disposal, remove the mulching
plug and t the grass box making sure the top ap is properly closed.
Empty the grass box regularly, otherwise the discharge chute will become
blocked with grass cuttings.
If you are making a light cut and wish for the grass cuttings to remain on
the lawn, t the mulching plug and close the top ap to cover the
discharge opening. It is not necessary to t the grass box in this case.
The mower is designed to operate and cut most eectively when moving
forwards.
Page 8
13 14
GENERAL MOWING TIPS GENERAL MOWING TIPS
x1
x1
x1
x1
x2
x2
x1
Page 9
15 16
GENERAL MOWING TIPS GENERAL MOWING TIPS
Page 10
15 16
GENERAL MOWING TIPS GENERAL MOWING TIPS
!
Page 11
17 18
GENERAL MOWING TIPS TECHNICAL SPECIFICATIONS
Product s pecifications
Rated voltage (AC)
220-240V ~ 50Hz
Rated pow er (AC)
1300 W
Width of cut
33 cm
Height of cut
25-65 mm
No-load s peed
3600±10% min-1
Weight
8.8 kg
Grassbox capacity
35 L
Loading...