Blanco BDW1465X Instruction Manual

Instruction ManualInstruction Manual

BDW1465X

DishwasherDishwasher

14 place settings

Compartment A:Compartment A:
For each wash cycle.
Compartment B:B:
For programs with pre-wash only.

(Follow the user instructions)

Mechanical indicator C. Mechanical indicator C.
Electric indicator on control panel (if provided).

Check the rinse aid level

Load the baskets

Select a programme

Running the dishwasher

Switch off the appliance

Turn off the water tap,
unload the baskets

Fill the detergent dispenser

Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid scald,as
the dishes and utensils are still hot and more susceptible to break.
They could also dry better.Unload the appliance, starting from the lower basket.

Changing the programme

Add forgotten dishes in the
dishwasher.

Scrape off any large food particles. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.

When the working cycle is finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
If the appiance was under standby mode, it will be power off automaticly after 30 minutes without any operation.

If the appliance is switched
off during a wash cycle.

Open the door carefully.
Hot steam may escape
when the door is opened!

WARNING!

If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).

Switch on the appliance

Quick Operation GuideQuick Operation Guide

For detailed operating method read the corresponding content on the instruction manual.

Open the door, press the On/Off button to switch on the appliance.

T urn on the water tap and press the Start/Pause Button. The machine will start working
after about 10 seconds.

Close the door,press the Program Button until the selected program lights up.
( See the section entitled Operation instruction )

1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.

2. Press the Start/Pause button to stop the machine .Press the Program button more than
3 seconds , the machine will be in standby state, then you can change the program to the
desired cycle setting

1.Press the Start/Pause Button to stop the washing.

2.Open the door a little .

3.After the spray arms stop working, you can open the door
completely.

4.Add forgotten dishes.

5.Close the door

6.Press the Start/Pause Button, the dishwasher will run
after 10 seconds.

A

B

C

KEEP THESE INSTRUCTIONS

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY

1.IMPORTANT SAFETY INFORMATION

READ ALL OF THE INSTRUCTIONS BEFORE USING

1.IMPORTANT SAFETY INFORMATION

READ ALL OF THE INSTRUCTIONS BEFORE USING

11

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of an electric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipment­grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.

WARNING!

WARNING! PROPER USE

Keep children away from detergent and rinse aid,
keep children away from the open door of the
dishwasher, there could still be some detergent left
inside.

Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.

Do not touch the heating element during or
immediately after use.
(This instruction is only applicable to machines
with a visual heating element.)

Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic it ems
nots

o m

arked,c

heck th em

anufacturer's

recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.

Do not place any heavy objects on or stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed:

1) Locate sharp items so that they are not likely
to damage the door seal;

2) WARNING: KNIVES AND OTHER UTENSILS
WITH SHARP POINTS MUST BE LOADED IN
THE BASKET WITH THEIR POINTS DOWN
OR PLACED IN A HORIZONTAL POSITION.
When using your dishwasher, you should
prevent plastic items from coming into contact
with the heating element.(This instruction is only
applicable to machines with a visual heating
element.)
Check that the detergent comparment is empty
after completion of the wash cycle.

When using your dishwasher, follow the precautions listed below:

WARNING! WARNING!

Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.

Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.

During installation, the power supply must not
be excessively or dangerously bent or flattened.

Do not tamper with controls.

If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.

Please dispose of packing materials properly.
Use the dishwasher only for its intended function.

Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.

WARNING:SOME DISHWASHER DETERGENTS ARE

STRONGLY ALKALINE, THEY CAN BE EXTREMELY
DANGEROUS IF SWALLOWED. AVOID CONTACT
WITH SKIN AND EYES AND KEEP CHILDREN AWAY
FROM THE DISHWASHER WHEN THE DOOR IS
OPEN.

The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.

The maximum number of place settings to be
washed is 14.
The maximum permissible inlet water pressure is
1Mpa.

The minimum permissible inlet water pressure is

0.04Mpa.

should be supervised to ensure that they
do not play with the appliance.

Young children

This appliance is not intended for use by persons
(including children )with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.

The door should not be left open,
since this could increase the risk of tripping.

If the appliance is installed on a carpet floor, take
care that openings in its base are not obstructed.

2.Operation Instruction2.Operation Instruction

22

Dishwasher FeaturesDishwasher Features

before using it for the first time.

To get the best performance from your dishwasher, read all operating instructions

IMPORTANTIMPORTANT

Control PanelControl Panel

11

22

33 44 6655 7 7

88

8. Start /Pause button: To start the selected
washing program or pause the washing program
when the machine is working.

1. On/Off Button: To switch On/Off the appliance.

7. Extra Drying function select Button :To select Extra
Drying function.(With this function only be used with
programmes Intensive,Heavy, ,Glass and 90min.)Normal

3. Power indicator :To show when the power on.

2. Program Button : To Press the button to select
appropriate Program.

4. Program indicators:To show which program
you have chose.

6. Program end and Rinse aid warning indicators:
To show when the program end or dispenser need to
be refilled.

5. Extra Drying indicators:To show Extra Drying function
starting up or not.

Back View

1

2

3

4
5

6

7

8

9

Front view

Lower basket

Dispenser

Cup shelf

Spray arms

Filter assembly

Inlet pipe connector

Drain pipe

Upper basket

Cutlery rack

Top spray arm

1

Inner pipe

5
6

7
8

9

10

12

11

3

2

4

Adjuster

12

10

11

C (Rinse-Aid indicator)C

33

3.Prior to using for the first time3.Prior to using for the first time

Before using your dishwasher for the first time:

A. Fill the rinse aid dispenser

B. Fill in detergent

A. Rinse Aid DispenserA. Rinse Aid Dispenser

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can
leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is
designed to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely
black. The volume of the rinse aid container is about 110ml.

Rinse Aid Dispenser

Function of Rinse Aid

Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.

Attention!

Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.

As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 fu ll
1 / 2 fu ll
1 / 4 full - Should refill to eliminate spotting
Empty

If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color of the
optical level indicator "C" located next to the cap. When the rinse-aid container is full, the whole indicator will be
dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let the rinse aid get below
1 / 4 full.

When to Refill the Rinse Aid Dispenser

How to fill the Rinse Aid Dispenser

To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.

Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills
with a damp cloth. Don't forget to replace the cap before you close dishwasher door.

Attention!
Clean up any rinse aid spill during filling with an absorbent cloth to avoid excess foaming during the next wash.

1
2
3

44

Adjusting Rinse Aid Dispenser

The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are a problem, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are show spots, adjust the dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)

Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.

Adjust lever
(Rinse)

Adjust lever
(Rinse)

during the next wash. Don't forget to replace the cap before you close dishwasher door.

Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming

NOTE:NOTE:

NOTE:NOTE:

Detergents have chemical ingredients that are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of the commercial quality detergents are suitable for this purpose.

B. DetergentB. Detergent

Detergents

There are 3 sorts of detergents

1.With phosphate and with chlorine

2.With phosphate and without chlorine

3.Without phosphate and without chlorine

MAXMAX

Based on their chemical composition, detergents can be split in two basic types:

The use of normal washing programs in combination with concentrated detergents
reduces pollution and is good for your dishes; these wash programs are specifically matched
to the dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason

normal wash programs in which concentra te d dete rgents are use d can achie ve t he sa me

results that can otherwise only be achieved using intensive programs.

Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programs. Therefore please use long programs when using detergent tablets, to
ensure the complete removal of detergent residuals.

The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than
Conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Always add the
detergent just before starting the dishwasher, otherwise it could get damp and will not
dissolve properly.

Concentrated Detergent

Detergent Tablets

Detergent Dispenser

Conventional, alkaline detergents with caustic components
Low alkaline concentrated detergents with natural enzymes

Normally new pulverised detergent is without phosphate. Thus the water softener function of

phosphate is not given. If detergents without phosphate are used in the case of hard water

often white spots appear on dishes and glasses. In this case please add more detergent to reach

better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not

be removed completely. In this case please choose a program with a higher temperature.

55

Adding detergent to dispenser

Proper Use of Detergent

Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser until you're ready to wash dishes.

Dishwasher detergent is corrosive!
Take care to keep it out of reach of children.

WARNING! WARNING!

Always add the detergent just before starting each wash cycle.
Only use branded detergent and rinse aid for dishwasher.

If the lid is closed: push the latch to open.

NOTE:NOTE:

Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on the right:

For main wash detergent.

For pre-wash detergent.

Please observe the manufacturers dosing and storage
Recommendations as stated on the detergent packaging.

Close the lid and press until it locks in place.

If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.

A

B

Fill in Detergent

You see information about the amount of detergent for the single programme on page 8.
Please be aware that soiling levels and water hardness can effect wash results.
Please observe the manufacturer's recommendations on the detergent packaging.

Push latch to openPush latch to open

AA BB

4.Loading the Dishwasher Baskets4.Loading the Dishwasher Baskets

Suitability of use in the dishwasherSuitability of use in the dishwasher

Cutlery with wooden, horn china or
mother-of-pearl handles.
Plastic items that are not heat resistant.
Older cutlery with glued parts that are not
temperature resistant.
Bonded cutlery items or dishes.
Pewter or cooper items.
Crystal glass.
Steel items subject to rusting.
Wooden platters.
Items made from synthetic fibres.

Some types of glasses can become
dull after a large number of washes.

Silver and aluminum parts have a
tendency to discolour during washing.

Glazed patterns may fade if machine
washed frequently.

Not suitable for use

Limited suitability

Dishes and items of cutlery must not lie inside one another, or cover each other.
To avoid damage to glasses, they must not be touched.
Load large items which are most difficult to clean into the lower basket.
The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffee
and tea cups.
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontally in the upper basket.
Please do not overload your dishwasher. This is important for good results and for
reasonable consumption of energy.

Load hollow items such as cups, glasses, pans etc. With the opening facing downwards so that
water cannot collect in the container or a deep base.

RecommendationRecommendation

Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program with as low temperature as possible.
To prevent damage, do not take glass and cutlery out of the dishwasher immediately
after the program has ended.

(For the best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlery baskets may vary from your model.)

Scrape off any large food particles. Soften remnants of burnt food in pans.
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:

1.Items such as cups, glasses, pots/pans, etc. are faced downwards.

2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.

3.All utensils are stacked securely and can not tip over.

4.All utensils are placed in the way that the spray arms can rotate freely during washing.

NOTE:NOTE:

Very small items should not be washed in the dishwasher as they could easily fall out of the basket.

Attention before or after loading the Dishwasher BasketsAttention before or after loading the Dishwasher Baskets

To prevent water dripping from the upper basket into the lower basket, we recommend that you
empty the lower basket first and then the upper basket.

Removing the DishesRemoving the Dishes

66

77

The upper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
tea cups and saucers, as well as plates, small bowls
and shallow pans (as long as they are not too dirty).
Position the dishes and cookware so that they will
not get moved by the spray of water.

Loading the Upper BasketLoading the Upper Basket

We suggest that you place large items and the most
difficult to clean items are to be placed into the lower
basket: such as pots, pans, lids, serving dishes and
bowls, as shown in the figure below. It is preferable to
place serving dishes and lids on the side of the racks
in order to avoid blocking the rotation of the top spray
arm.

Loading the Lower BasketLoading the Lower Basket

Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slanted to allow water to flow out.

Please be reminded that:

The Bottom Basket features folding spikes so that larger or more pots and pans can be loaded.

The Method Loading Normal DishwareThe Method Loading Normal Dishware

IN

Folding Spikes of Lower Basket

For better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.

Folding back the cup shelves

For better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.

Cutlery should be placed into the cutlery rack separately
from each other in the appropriate positions, and do
make sure the utensils do not nest together, this may
cause bad performance.

Cutlery BasketCutlery Basket

For a top quality cleaning, place the silverware in
the basket making sure that:

For a top quality cleaning, place the silverware in
the basket making sure that:

They do not nest together.They do not nest together.
Silverware is placed with the male face up.Silverware is placed with the male face up.
Long utensils in the middle. Long utensils in the middle.

IN

5.Starting a washing program5.Starting a washing program

Wash Cycle TableWash Cycle Table

NOTE:NOTE:

Means: need to fill rinse aid into the Rinse-Aid Dispenser.

( )

88

Turning On the ApplianceTurning On the Appliance

Starting a cycle wash

Draw out the lower and upper basket, load the dishes and push them back.

It is recommended to load the lower basket first, then the upper one (see the section entitled
Loading the Dishwasher ).

Pour in the detergent (see the section entitledSalt, Detergent and Rinse Aid).
Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification

of the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.

Open the door, press the power button, and the On/Off light will turn on.
Press the program Button, the wash program will be changed as follows direction:

Glass 90min Soak Intensive Heavy
If a program is selected, the response light will turn on. Then close the door, press the start/pause button,
the dishwasher will start its cycle.

1

2
3

4
5

Normal NormalNormal NormalGlass 90min Soak Intensive Heavy

NOTE:NOTE:

*AS/NZS 2007.1

AS/NZS 2007.1

: This programme is the test cycle. The information for comparability test

in accordance with , as follows:

Capacity: 14 settings
Position Upper basket: upper wheels on rails
Rinse aid setting: 6
PI:0.49w;Po:0.45w

90 Min

Detergent

pre/main

Detergent

pre/main

Cycle Selection

Information

Cycle Selection

Information

ProgramProgram

Running

time(min)

Running

time(min)

Water

(L)

Water

(L)

Energy

(Kwh)

Energy

(Kwh)

Rinse

Aid

Rinse

Aid

Description

of Cycle

Description

of Cycle

Intensive

Heavy

For heavily soiled loads,
such as pots, plates, glasses
and lightly soiled pans.

For normally soiled loads,
such as pots, plates, glasses
and lightly soiled pans.
standard daily cycle.

For heaviest soiled crockery,
and soiled pots pans
dishes etc with dried
on soiling.

For soiled loads
that need quick wash.

For lightly soiled loads,
such as glasses,
crystal and fine china.

Glass

Pre-wash
wash(42 )
Rinse
Rinse(60 )
Drying

125

0.8

13

(Or All in1)

5/27.5g

5/27.5g
(Or All in1)

(Or All in1)

5/27.5g

Pre-wash(50 )
Wash (60 )
Rinse
Rinse
Rinse(65 )
Drying

Pre-wash(45 )
Wash (55 )
Rinse
Rinse (65 )
Drying

Pre-wash
Wash (45 )
Rinse(50 )
Drying

160

170

170

1.3

0.7

1.5

17.5

13.5

12.0

Wash(65 )
Rinse
Rinse (65 )
Drying

90

11.5

1.2

25g

(Or All in1)

5/27.5g

(Or All in1)

To rinse dishes that you plan
to wash later that day.

Pre-wash

8 0.02

4

Soak

99

When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid scald the dishes and utensils
are still hot and more susceptible to breakage. They will also dry better.

Switch Off the Dishwasher

The Led screen is on but the colon icon is not blinking, only in this case the programme has ended.

1.Switch off the dishwasher by pressing the ON/OFF button.

2.Turn off the water tap.

Open the door carefully.

Hot dishes are sensitive to knocks. The dishes should be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.

Unloading the dishwasher

It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.

Forgot to Add a Dish?Forgot to Add a Dish?

At the End of the Wash CycleAt the End of the Wash Cycle

A forgotten dish can be added any time before the detergent cup opens.

Add forgotten dishes.

Close the door

After the spray arms stop working, you can open the door

completely.

2

3

Open the door a little .

1

4

5

6

Press the Start/Pause Button to stop the washing.

Press the Start/Pause Button, the dishwasher will run
after 10 seconds.

Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.

NOTE:NOTE:

When following this procedure from step1 to step 3, the filter system will be removed;
when following it from Step 3 to Step 1, the filter system will be installed.

WARNING! WARNING!

It is dangerous to open the door when washing, because the hot water may scald you.

Change the ProgramChange the Program

If you open the door during a wash cycle , the machine will pause. The program light will
stop blinking and the buzzer will mooing every minute unless you close the door . After
you close the door ,the machine will keep on working after 10 seconds.

NOTE:NOTE:

Premise:

A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled " Loading the
Detergent " ).

Press the Start/Pause button to stop the machine .Press the Program button more than
3 seconds , the machine will be in standby state, then you can change the program to the desired cycle setting
(see the section entitled " Starting a wash cycle. . ." ).

1

2

The filter prevents larger remnants of food or other objects from getting inside the pum.
The residues may block the filter, in this case they must be removed.

The filter system consists of a coarse filter, a flat (Main filter)

and a microfilter(Fine filter).

Food and soil particles trapped in this filter are pulverized by a
special jet on the lower spray arm and washed down to drain.

Larger items, such as pieces of bones or glass, that could block

the drain are trapped in the coarse filter. To remove the items

caught by this filter, gently squeeze the tap on the top of this

filter and lift it out.

This filter holds soil and food residues in the sump area and

prevents it from being redeposit on the dishes during wash cycle.

Main filter

1

Coarse filter

2

Fine filter

3

2

3

1

Filter assembly

The filter efficiently removes food particles from the wash water, allowing it to be recycled during the cycle.
For best performance and results, the filter must be cleaned regularly. For this reason, it is a good idea to
remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and
cup under running water. To remove the filter device, pull the cup handle in the upward direction.

WARNING! WARNING!

The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.

nn
nn

Step 1 Turn the filter in anti-clockwise direction.

Step 2 Lift the filter assy up.

6.Maintenance and Cleaning6.Maintenance and Cleaning

Filtering SystemFiltering System

NOTE:NOTE:

When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.

1010

1

2

OpenOpen

The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.

For the exterior, use a good appliance polish wax.

Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.

Protect Against Freezing

1.Cut off the electrical power to the dishwasher.

2.Turn off the water supply and disconnect the water inlet pipe from the water valve.

3.Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)

4.Reconnect the water inlet pipe to the water valve.

5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.

please take frost protection measures on the dishwasher in winter. Every time after washing cycles,
please operate as follows

Caring for the DishwasherCaring for the Dishwasher

Cleaning the Filter

Cleaning The Door

To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
on the last page and reinsert the entire assembly in the dishwasher, positioning it in its seat and pressing downwards.

When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of the dishwasher could be decreased.

WARNING! WARNING!

To clean the edge around the door, you should use only a soft warm, damp cloth.
To avoid penetration of water into the door lock and electrical components, do not
use a spray cleaner of any kind.

WARNING! WARNING!

Never use a spray cleaner to clean the door panel as it may damage the door lock
and electrical components.
Abrasive agents or some paper towels should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.

nn

nn

Cleaning the Spray Arms

NOTE:NOTE:

If your dishwasher cannot work because of the ice,
please contact professional service persons.

It is necessary to clean the spray arms regularly for hard
water chemicals will clog the spray arm jets and bearings.

- Inspect the filters for blocking after every time the dishwasher has been used.

- By unscrewing the coarse filter, you can remove the filter system. Remove any food remnants and
clean the filters under running water.

Notes:

The entire filter assembly should be cleaned once a week.

NOTE:NOTE:

To remove the lower spray arm, pull out the spray arm upward.

To remove the upper spray arm, hold the nut, rotate the arm
clockwise to remove it.

Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.

1111

OpenOpen

It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance.

If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.

One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.

Electrical Requirements

Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and burns.

Electrical Connection

Insure proper ground

exists before use

GROUNDING INSTRUCTIONS

7.Installation instruction7.Installation instruction

Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned for levelling, the height of the dishwasher
may be altered via adjustment of the screwing level of the feet.

Positioning the AppliancePositioning the Appliance

About Power ConnectionAbout Power Connection

WARNING! WARNING!

For personal safety:

DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.

nn
nn

Before cleaning or performing maintenance, always
remove the plug from the socket.

To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water an a little
vinegar, or a cleaning product made specifically for
dishwashers.

Remove the Plug

No Solvents or Abrasive Cleaning

Moving the Appliance

Seals

How to Keep Your Dishwasher in Shape

After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.

After Every Wash

When not in Use for a LongTime

This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a
cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.

nn

1212

1313

for personal safety:

DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE

FROM THE POWER CORD.

EARTHING

CONNECTION

nn
nn

WARNING! WARNING!

Improper connection of the equipment earthing conductor can result in the risk of an
electric shock.
Check with a qualified electrician or service representative if you are in doubt whether the
appliance is properly earthed.
Do not modify the plug provided with the appliance. If the plug does not fit properly to the
outlet, please have a qualified electrician to install a proper outlet.

nn

nn

nn

A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink
has one, it is recommended that the hose be disconnected and the hole plugged.

WARNING!

ABOUT THE SAFETY SUPPLY HOSE.

How to Connect the safety supply hose

Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.

Turn water fully on before starting the dishwasher.

1

Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.

The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the
flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer
corrugated hose is full of water.

2
3

The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.

Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the
minimum consult our Service Department for advice.

Turn off the water.

Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
room, from severe splashing.

Unscrew the safety supply hose from the faucet.

3

2

1

How to Disconnect the safety supply hose

COLD WATER CONNECTION

Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked
and damage the appliance.

1414

The following things should be checked before starting the dishwasher.

Start of Dishwasher Start of Dishwasher

The content of this manual is very helpful to the users.

After installation, please make sure to keep this manual.

Attention:Attention:

1 The dishwasher is level and fixed properly.
2 The inlet valve is open.
3 There is a leakage at the connections of the conducts.
4 The wires are tightly connected.
5 The power is switched on.
6 The inlet and drain hoses are knotted.
7 All packing and print materials should be taken out of the dishwasher.

Drain hose Connection

Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.

MAX 1000mm

A

Counter

Front

Drain pipe

NOTE
The top of the hose
must be less than
1000mm.

40mm

B

PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, BPLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B

1515

8.Troubleshooting Tips8.Troubleshooting Tips

Problem Possible CausesWhat To Do

Fuse blown, or the
circuit breaker acted

Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher

Suds in the tub

Spilled rinse-aid

Always wipe up rinse-aid spills immediately.

Review the charts on the following pages may save you from calling for service.

White film on

inside surface

There are rust

stains on cutlery

Knocking noise

in the wash cabinet

Rattling noise

in the wash cabinet

Knocking noise

in the water pipes

Hard water minerals

The affected items are
not corrosion resistant.

A spray arm is
knocking against
an item in a basket

Items of crockery
are loose in the
wash cabinet

This may be caused
by on-site installation
or the cross-section of
the piping.

To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.

Interrupt the program, and rearrange the items
which are obstructing the spray arm.

Interrupt the program,
and rearrange the items of crockery.

This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.

Stained tub interior

Detergent with
colourant was used

Make sure that the detergent is the one without
colourant.

Improper detergent

Dishwasher doesn't

start

Make sure the dishwasher is turned on and the door is
closed securely.

Check that the water supply is connected properly and
the water is turned on.

Make sure to close the door properly and latch it.

Make sure the power cord is properly plugged into the
wall socket.

Power supply is not
turned on

Error code:E1;
Water pressure is low

Door of dishwasher
not properly closed.

water not pumped

from dishwasher

Kink in drain hose

Filter clogged

Kitchen sink clogged

Check drain hose.

Check coarse the filter
(see section titled " Cleaning The Filter ")

Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.

Before Calling for Service Before Calling for Service

Technical
problems

General
problems

Noise

Use only the special dishwasher detergent to avoid suds.
If this occurred, open the dishwasher and let suds evaporate.
Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then select any cycle. Dishwasher will drain
out the water at the first step. Open the door after draining
is stop and check if the suds is disappeared.
Repeat if necessary.

The items should be corrosion resistant.

Error CodesError Codes

1616

Problem Possible Causes What To Do

The dishes were not
loaded correctly.

See notes in " Loading the Dishwasher Baskets ".

The dishes

are not clean

Cloudiness

on glassware

Black or gray

marks on dishes

Detergent left in

dispenser cups

The dishes

are not drying

Select a more intensive programme.
See" Wash Cycle Table ".

Use more detergent, or change your detergent.

Rearrange the items so that the sprayer can rotate freely.

Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".

Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.

Use a mild abrasive cleaner to eliminate those marks.

Re-loading the dishes properly.

Load the dishwasher as suggested in the directions.

Increase the amount of rinse-aid/refill the rinse-aid
dispenser.

Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once the
dishes are barely warm by touching. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.

In short program the rinse temperature is lower.
This also lowers cleaning performance. Choose
a program with a long high rinse temperature.

Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.

The program was
not powerful enough.

Not enough detergent
was dispensed.

Items are blocking
the path of spray arms.

The filter combination
is not clean or
is not correctly fitted.
This may cause
the spray arm jets
get blocked.

Combination of soft
water and too much
detergent.

Aluminum utensils
have rubbed against
dishes.

Dishes block
detergent cup opens.

Improper loading

Too little rinse-aid

Dishes are removed
too soon

Wrong program
has been selected

Use of cutlery with
a low-quality coating

Unsatis

-factory
washing
result

Unsatis

-factory
drying
result

When some malfunctions occur, the appliance will display error codes to warn you:

WARNING! WARNING!

If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.

nn
nn

Overflow.

Codes

Meanings

Possible Causes

Longer inlet time.

Faucets is not opened, or water intake is
restricted,or water pressure is too low.

Some element of dishwasher leaks .

The soak light flicker fleetly

Failure of water diverter

Open circuit or break of Water Diverter.

Not reaching the required temperature

Malfunction of the heating element .

The 90min and soak lights
flicker fleetly

The glass light flicker fleetly

The light flicker fleetly Normal

1717

Height : 845mm
Width : 598m m

Depth : 600mm(with the door closed)

Water pressure: 0.04-1.0MPa
Power supply: see rating label

Capacity: 14 place settings

Technical InformationTechnical Information

5

9

8

5

9

8

845845

117

5117

5

6

0

0

(w

it

h t

h

e d

o

or

c

lo

sed

)

6

0

0

(w

it

h t

h

e d

o

or

c

lo

sed

)

1.Upper basket:1.Upper basket:

Loading the baskets according to (*AS/NZS 2007.1) : Loading the baskets according to :

a

a

a

a

a

c

c

c

c

c

c

c

c

c

a

a

a

a

a

a

a

a

a

c

Glasses

Saucers

b

Cups

a

IN

b

c

c

c

c

c

2

.L

ow

e

r

ba

s

ke

t

:2

.L

ow

e

r

ba

s

ke

t

:

d

Dinner plates

e

Soup plates

Dessert dishes

f

b

IN

e

f

f

f

d

3

.

Cutt

erly

basket

:3

.

Cutt

erly

basket

:

IN

1

1

Forks

1

Soup spoons

2

3

Dessert spoons

Teaspoons

4

Knives

5

V

o

lt

ag

e:

220

~

2

4

0V

/

50

H

z

V

o

lt

ag

e:

220

~

2

4

0V

/

50

H

z

I

nfo

r

ma

t

ion

f

or

co

mpar

ab

il

i

ty

te

s

ts

in

a

ccord

an

c

e

w

i

t

h

(*

AS

/N

ZS

20

07.

1

)

C

apac

it

y: 14

p

l

ac

e

set

ti

n

gs

C

apac

it

y: 14

p

l

ac

e

set

ti

n

gs

P

o

si

ti

o

n

o

f t

h

e

upp

e

r

bas

k

et

:

l

ow

e

r

P

o

si

ti

o

n

o

f t

h

e

upp

e

r

bas

k

et

:

l

ow

e

r

2

2

3

3

4

4

5

5

P

r

ogr

a

m

m

e

:

N

o

r

mal

P

r

ogr

a

m

m

e

:

N

o

r

mal

R

i

ns

e ai

d

se

tt

i

n

g

: 6

R

i

ns

e ai

d

se

tt

i

n

g

: 6

D

ete

rg

ent

(P

r

e/m

a

i

n)

:

5

g

/

27.

5 g

D

ete

rg

ent

(P

r

e/m

a

i

n)

:

5

g

/

27.

5 g

3

.

Cutt

erly

basket

:3

.

Cutt

erly

basket

:

D

oor

is

op

en

at

th

e

e

nd

of

th

e d

ry

i

ng

c

yc

le

fo

r

th

e

d

ry

i

ng

p

e

rfo

r

manc

e te

s

t

(D

oo

r

p

o

si

ti

on:

Ope

n

5

0

mm

)

D

oor

is

op

en

at

th

e

e

nd

of

th

e d

ry

i

ng

c

yc

le

fo

r

th

e

d

ry

i

ng

p

e

rfo

r

manc

e te

s

t

(D

oo

r

p

o

si

ti

on:

Ope

n

5

0

mm

)