Blade BLH8500 Manual

0 (0)

3. Attach the fpv monitor holder to the MLP4DSM transmitter. a. Slide the holder down over the antenna. b. Tighten the clamp screw. Do not overtighten. c. Open the clamp jaws and place the monitor in the

jaws. The angle of the monitor can be adjusted by loosening the angle adjustment knob, rotating the clamp up or down and tightening the adjustment knob.

NOTICE: Consult local laws and ordinances before operating FPV (ﬁ rst person view) equipment. In some areas, FPV operation may be limited or prohibited. You are responsible for operating this product in a legal and responsible manner.

FPV RTF/BNF

Instruction Manual / Bedienungsanleitung / Manuel d’utilisation / Manuale di Istruzioni

Age Recommendation: Not for children under 14 years. This is not a toy.

Charging Warnings

WARNING: Failure to comply with the

following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.

• NEVER LEAVE CHARGING BATTERIES UNATTENDED.

• NEVER CHARGE BATTERIES OVERNIGHT.

• Never charge damaged batteries. If the battery begins to swell during charging or use, discontinue immediately.

• Always use the included battery and charger. Disconnect the battery after charging.

• Charge batteries away from ﬂ ammable materials in a well-ventelated area.

• Never charge, transport, or store batteries in hot, cold, or very sunny places (recommended between 40–120° F or 5– 49° C).

Specifications

Length

3.26 in (83mm)

Propeller Diameter

2.56 in (65mm)

Height

1.10 in (28mm)

Flying Weight

.85 oz (24 g)

Install 4 AA batteries into the transmitter, noting polarity. Replace the transmitter batteries when the power LED ﬂ ashes and the transmitter beeps.

We recommend using only alkaline AA batteries in the transmitter, however, it is possible to use rechargeable NiMH batteries.

CAUTION: If using rechargeable batter-

ies, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.

Charge the Flight Battery

Install the Transmitter Batteries (RTF)

Transmitter and Receiver Binding

NOTICE: Inspect the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured. Charge only batteries that are cool to the touch and are not damaged.

Insert the charger into a USB port. Connect the battery to the charger.

CHARGING (Solid Red LED) MAX CHARGE (LED OFF )

Disconnect the ﬂ ight battery from the charger immediately upon completion of charging.

CAUTION: Only use chargers speciﬁ cally designed to charge the included Li-Po battery. Failure to do so could result in ﬁ re, causing injury or property damage.

CAUTION: Never exceed the recommended charge rate. CAUTION: Once charging is complete, immediately remove the battery.

Never leave a battery connected to the charger.

Install the Flight Battery

BNF

Transmitter

If you are using a computer transmitter, in the channel input menu, set channel 6 (Aux1) to a momentary switch such as the bind button (I ). Set the model type to “Acro” or “Airplane” mode. Bind the quadcopter to your transmitter following the directions below.

General Binding Procedure (BNF®)

1. Disconnect the ﬂ ight battery from the quadcopter.

2. Set the model type in your transmitter settings to “Acro” mode.

3. Center all trims on your transmitter.

4. Power off the transmitter and fully lower the throttle.

5. Connect the ﬂ ight battery in the quadcopter. The LED on the 3-in-1 control unit ﬂ ashes red during initialization, then ﬂ ashes blue when it is ready to bind.

6. Put the transmitter into bind mode while powering on the transmitter.

7. Release the bind button/switch after 2–3 seconds. The quadcopter is bound when the blue LED on the 3-in-1 control unit turns solid.

8. Disconnect the ﬂ ight battery and power the transmitter off.

MLP4DSM Binding Procedure (RTF)

1. Disconnect the ﬂ ight battery from the quadcopter.

2. Center all trims on your transmitter.

3. Power off the transmitter and fully lower the throttle.

4. Connect the ﬂ ight battery in the quadcopter. The LED on the 3-in-1 control unit ﬂ ashes red during initialization, then ﬂ ashes blue when it is ready to bind.

5. When the blue light is ﬂ ashing, push in and hold down the left stick while powering on the transmitter (you will hear a ‘click’ and a long tone).

6. Release the left stick. The transmitter will beep and the power LED will blink. The quadcopter is bound when the blue LED on the 3-in-1 control unit turns solid.

7. Disconnect the ﬂ ight battery and power the transmitter off.

If you encounter problems, obey the binding instructions and refer to the troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support ofﬁ ce. For a list of compatible DSM

transmitters, please visit www.bindnﬂ y.com.

CAUTION: Always disconnect the Li-Po battery from the aircraft

when not ﬂ ying to avoid over-discharging the battery. Batteries discharged to a voltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential ﬁ re when the batteries are charged.

Throttle down

Power ON

Transmitter Control (RTF)

A B C D E F

Mode1Aileron (Left/Right)

Throttle (Up/Down)

Throttle Trim

Aileron Trim

Rudder Trim

Elevator Trim

Rudder (Left/Right) Elevator (Up/Down)

Mode2Aileron (Left/Right)

Elevator (Up/Down)

Elevator Trim

Aileron Trim

Rudder Trim

Throttle Trim

Rudder (Left/Right) Throttle (Up/Down)

Operating Safety Precautions

• As the user of this product, you are responsible for operating it safely, not endangering yourself and others, or damaging the product or the property of others.

• Operate your product in open spaces away from people and property.

• Never operate your product with damaged electrical components.

• Keep the transmitter powered on while model is powered on.

• Let parts cool after use before touching, motors will get hot in use.

• Remove batteries after use, as applicable.

General Product Safety Precautions

• Keep all batteries, chemicals, small parts and anything electrical out of the reach of children.

• Avoid water exposure to this product. Keep parts dry.

• Keep moving parts clean.

The LEDs on the Inductrix indicate the front and back of the quadcopter. The white LEDs indicate the front. The red LEDs indicate the back.

Takeo

Increase the throttle until the model is approximately 2 ft. (600mm) off the ground in a low-level hover and concentrate on balancing the throttle stick’s position so that the quadcopter holds a steady hover altitude. In some cases, you may need to make a few short “hops” to an altitude of just a few inches until you become familiar with the control inputs and trim settings required to maintain a steady hover and altitude.

Hovering

The Inductrix quadcopter requires minor throttle adjustments to maintain its altitude in hover. Remember to keep these throttle adjustments as minimal as possible. Large adjustments could result in a loss of control or a possible crash.

While attempting to establish a low-level hover, check to see if any trim adjustments are required to help keep the quadcopter from constantly drifting in various directions. If you ﬁ nd that it constantly drifts without any directional control input, land the model before making any adjustments to the trim settings.

• If the nose of the quadcopter rotates to the left or right, adjust the rudder trim.

• If the quadcopter continually drifts forward or backward, adjust the elevator trim.

• If the quadcopter continually drifts to the left or right, adjust the aileron trim.

Continue making minor trim adjustments until the machine hovers at a low altitude with very little drifting and directional control input. If this is your ﬁ rst multicopter or helicopter, seek the help of an experienced pilot to trim the model for you before making your ﬁ rst ﬂ ight.

With your quadcopter properly trimmed and maintaining a stable low-level hover, practice using the rudder, elevator and aileron controls to familiarize yourself with the machine’s responses to control inputs. Remember to keep the control inputs as minimal as possible.

Average ﬂ ight times are approximately 4 minutes.

NOTICE: Crash damage is not covered under warranty.

To prevent excessive wear to the motors, always allow the motors to cool between ﬂ ights.

Fly the Quadcopter

Low Voltage Cuto (LVC)

Video Monitor (RTF)

FPV Camera and Video Transmitter

Once the battery reaches 3V under load, the ESC will continuously lower power supplied to the motor until complete shutdown occurs. This helps prevent over-discharge of the Li-Po battery. Land immediately once the ESC activates LVC. Continuing to ﬂ y after LVC can damage the battery, cause a crash or both. Crash damage and batteries damaged due to over-discharge are not covered under warranty.

Repeatedly ﬂ ying the aircraft until LVC activates will damage the ﬂ ight battery. Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge.

During storage, make sure the battery charge does not fall below 3V per cell.

Dual rate selection

Bind/

Flight Mode

Selection

Rate Selection – RTF

The Inductrix® RTF quadcopter comes with the Blade

MLP4DSM transmitter.

• When powered on, this transmitter is automatically high rate.

• Change rates by pressing and releasing the right control stick.

• In low-rate mode, the quadcopter is limited to a lower bank

angle and will self-level when the control sticks are released. This mode is typically preferred by pilots looking for smoother/ easier control response during ﬁ rst time use.

• In high-rate mode, the quadcopter has a higer possible bank angle and will self-level when the control sticks are released.

Flight Mode Selection

Cycle between the ﬂ ight modes by pressing and releasing the left stick of the MLP4DSM or by pressing and releasing the momentary switch on your computer transmitter as programmed in the binding section above.

• S tability mode (blue LED): the bank angle is limited. When the sticks are released, the quadcop-

ter will return to level ﬂ ight.

• A gility mode (red LED): the quadcopter has no bank angle limits and will not return to level ﬁ ght if

the sticks are released. Use rates and expo to tune the performance according to your ﬂ ying style.

NOTICE: Do not attempt to change ﬂ ight modes while ﬂ ying with the MLP4DSM transmitter. Attempting to do so will cause the transmitter to register a faulty center position. Always land the quadcopter and release the sticks before changing ﬂ ight modes.

Dual rate selection

Aileron

Elevator

Rudder

Understand the Primary Flight Controls

If you are not familiar with the controls of your Inductrix quadcopter, take a few minutes to familiarize yourself with them before attempting your ﬁ rst ﬂ ight.

Throttle

Aileron left

Aileron right

ForwardElevator down

Elevator up

Backward

Left Side View Left Side View

Rudder left

Rudder right

Nose Yaws Right

Nose Yaws Left

Throttle down

Throttle up

Left Side View Left Side View

Descend

Climb

Left

Rear View

Right

Rear View

Power LED indicator

USB Li-Po Charger

EFLC1008

SOLID RED LED

–Charging

DC Input:5.0V 350mA DC Output:4.2V 300mA

LED OFF –Charge Complete

Your RTF transmitter comes prebound to the Inductrix. If you need to re-bind, follow the directions below.

On/Off Switch

When pressed down, trim buttons make a sound that increases or decreases in pitch at each pressing. The middle or neutral trim position is heard as a middle tone in the pitch range of the sounds. The end of the control range is sounded by a series of beeps.

To receive product updates, special offers and more, register your product at www.bladehelis.com.

1. Before using the Spektrum

4.3 inch Video Monitor make sure the monitor is charged thoroughly. Connect the micro USB connector to a 5V USB power source. The charge indicator LED will glow red while charging and green when the monitor is fully charged.

2. Attach the included antenna to the antenna connector located on the top of the monitor.

CAUTION: Do not power the monitor on without the antenna attached. Doing so will damage the video transmitter and

receiver ampliﬁ ers. Ampliﬁ er damage is not covered by warranty.

5.8GHz Antenna connector

Menu Button:

Use the + and – buttons to modify:

Channel Selection Button

Single push to change channel

Frequency Band Button

Single push to change band

AV In

Brightness Contrast Color

Mode (16:9, 4:3) Language Reset

1. Power on your radio transmitter, then power on the aircraft.

2. Power on the video receiver to make sure the channel is clear.

3. Select the desired video transmitter channel by pressing the button on the quadcopter as shown to scroll through the available bands (Fat Shark/IRC or Race) and channels (1-8). Fatshark channel 1 is indicated by a red internal LED on the quadcopter. Keep pressing and releasing the button to scroll through the remaining channels.

4. Perform a range test before ﬂ ying.

If you experience static in the video feed, select a different channel.

NOTICE: The 25mW micro video transmitter range on your quadcopter is less than your ﬂ ight control transmitter range. Ensure you have adequate video camera range for ﬁ lming.

Tip: If you are ﬂ ying with an FPV headset and are prone to motion sickness, sit in a chair. If you start to suffer from motion sickness while ﬂ ying, lower your chin against your chest. Fly in open areas, away from people, trees, cars, and buildings. The range of the system can be impacted by any obstructions blocking your signal. It is normal to see break up in the video going behind trees and other obstacles.

ON/Off Switch Charge Status LED

Red = charging Green = charged

5V Micro USB Charge Port

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal

property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some

basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁ cial injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

4. Turn on the monitor and look for a clear channel. Clear channels will have a consistent static background. Channels with interference will display horizontal static lines. Select one of the clear channels. The video transmitter included with the Inductrix FPV quadcopter transmits only on the Fat Shark/IRC and RaceBand bands, channels 1-8.

5. Once you have chosen a clear channel on the monitor, select the same channel on the video transmitter.

BAND CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8

Fat Shark/IRC 5740 5760 5780 5800 5820 5840 5860 5880 RaceBand 5658 5695 5732 5769 5806 5843 5880 5917

Band E 5705 5685 5665 5645 5885 5905 5925 5945 Band A 5865 5845 5825 5805 5785 5765 5745 5725

If you are operating this product in North America, you are required to have an Amateur Radio (HAM) license. Visit www.arrl.org for more information.

Parts List

Exploded View

Optional Parts List

Part # Description

BLH8500 Inductrix FPV RTF

BLH8580 Inductrix FPV BNF 1 BLH8501 Main Control Board 2 BLH8502 Clockwise Motor, Speed 3 BLH8503 Counter Clockwise Motor, Speed 4 BLH8504 Canopy: Inductrix FPV 5 BLH8505 FPV Camera 25mW w/ Raceband 6 BLH8506 Prop Set (4), Yellow 7 BLH8706 Main Frame 8 BLH2208 Smart Phone Holder: mLP TX

EFLC1008 1S USB Li-Po Charger, 300mA

EFLB2001S45 1S, 200mAh LiPo

SPMVM430 4.3 inch video monitor

Part # Description

EFLB1501S45 1S, 150mAh LiPo SPMVM430HA Headset conversion

FCC Information

IC Information

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Compliance Information for the European Union

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and make sure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city ofﬁ ce, your household waste disposal service or where you purchased the product.

EU Compliance Statement:

Horizon Hobby, LLC hereby declares that this product is in compliance with the essential

requirements and other relevant provisions of the R&TTE, RED, EMC and LVD Directives. A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

Troubleshooting Guide

Problem Possible Cause Solution

Will not respond to throttle

Throttle too high and/or throttle trim is too high

Reset controls with the throttle stick and throttle trim at the lowest setting

Does not function and smells burnt after connecting the ﬂ ight battery

Flight battery connected with the wrong polarity

Replace the 3-in-1 board. Connect the ﬂ ight battery noting proper polarity

LED on receiver ﬂ ashes rapidly and quadcopter will not respond to transmitter (during binding)

Transmitter too near aircraft during binding process

Power off the transmitter. Move the transmitter a larger distance from the aircraft. Disconnect and reconnect the ﬂ ight battery to the aircraft. Follow the binding instructions

Bind switch or button was not held while transmitter was powered on

Power off transmitter and repeat bind process

Aircraft or transmitter is too close to large metal object, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt binding again

LED on the receiver ﬂ ashes rapidly and the quadcopter will not respond to the transmitter (after binding)

Less than a 5-second wait between ﬁ rst powering on the transmitter and connecting the ﬂ ight battery to the quadcopter

Leave the transmitter powered on. Disconnect and reconnect the ﬂ ight battery to the quadcopter

The quadcopter is bound to a different model memory (ModelMatch

™

transmitters only)

Select the correct model memory on the transmitter. Disconnect and reconnect the ﬂ ight battery to the quadcopter

Flight battery or transmitter battery charge is too low

Replace or recharge batteries

Aircraft or transmitter is too close to large metal object, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt connecting again

Crashes immediately upon lift-off or doesn’t lift off

Propellers in wrong locations Make necessary adjustments

Static in FPV feed

Interference on chosen channel

Change the video transmitter and receiver channel

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTICE: Modiﬁ cations to this product will void the user’s authority to operate this equipment.

HINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby, LLC jederzeit geändert werden. Die aktuelle Produktliteratur ﬁ nden Sie auf horizonhobby.com unter der Registerkarte „Support“ für das betreffende Produkt.

BEDEUTUNG DER SIGNALWÖRTER

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

HINWEIS: Wenn diese Anweisungen nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe Gefahr von Verletzungen ergeben.

ACHTUNG: Wenn diese Anwesiungen nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die Gefahr von schweren Verletzungen.

ACHTUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu

Schäden am Produkt oder persönlichem Eigentum führen oder schwere Verletzungen verursachen. Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem

Menschenverstand betrieben werden und benötigt gewisse mechanische Grundfähigkeiten. Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby, LLC das Produkt zu zerlegen, es mit inkompatiblen Komponenten zu verwenden oder auf jegliche Weise zu erweitern.

Warnungen zum Laden

WARNUNG: Alle Anweisungen und

Warnhinweise müssen genau befolgt werden. Falsche Handhabung von Li-PoAkkus kann zu Brand, Personen- und/oder Sachwertschäden führen.

• ADEN SIE NIEMALS AKKUS UNBEAUFSICHTIGT.

• LADEN SIE NIEMALS AKKUS ÜBER NACHT.

• Laden Sie njemals beschädigte Akkus Sollte der Akku zu einem beliebigen Zeitpunkt beginnen, sich aufzublähen oder anzuschwellen, stoppen Sie die Verwendung unverzüglich.

• Verwenden Sie immer das Ladegerät und den Akku aus dem Lieferumfang. Trennen Sie nach dem Laden den Akku.

• Laden Sie die Akkus immer weit entfernt von brennbaren in gut belüfteten Bereichen.

• Laden, transportieren oder lagern Sie niemals Akkus in heißen, kalten oder Plätzen mit starker Sonneneinstrahlung. (Empfohlener Temperaturbereich 40 - 120°)

Sicherheitsvorkehrungen und Warnhinweise

• Als Nutzer dieses Produktes sind Sie allein für den sicheren Betrieb ohne Gefährdung des Produktes, ihrer selbst und dritter oder deren Eigentum verantwortlich.

• Betreiben Sie ihr Produkt auf weiten, offenen Flächen weg von Menschen und anderem Eigentum

• Betreiben Sie das Produkt niemals mit beschädigten elektrischen Komponenten

• Lassen Sie den Sender eingeschaltet wenn das Modell eingeschaltet ist

• Lassen Sie die Teile abkühlen bevor Sie sie anfassen. Die Motoren werden während des Betriebes heiß

• Allgemeine Sicherheitshinweise zum Produkt

• Halten Sie alle Batterien, Akkus, Chemikalien Kleinteile

und Elektronikkomponenten aus der Reichweite von Kindern

Allgemeine Sicherheitshinweise zum Produkt

• Halten Sie alle Akkus, Batterien, Chemikalien und Kleinteile und andere elektrische Komponenten aus der Reichweite von Kindern.

• Vermeiden Sie mit diesem Produkt Wasserkontakt. Halten Sie die Teile trocken.

• Halten Sie die beweglichen Teile sauber.

Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

Spezifikationen

Länge

83mm

Rotordurchmesser

65mm

Höhe

28mm

Fluggewicht

24 g

Bitte registrieren Sie ihr Produkt unter www.bladehelis.com um Updates, spezielle Angebote und weitere Informationen zu erhalten.

Setzen Sie unter Beobachtung der Polarität die Senderbatterien ein. Ersetzen Sie die Batterien wenn die LED blinkt und der Sender piept. Wir empfehlen AA Alkaline Batterien in dem Sender zu verwenden. Sie können auch wiederauﬂ adbare NiMH Akkus verwenden.

ACHTUNG: Wenn Sie wiederauﬂ adbare

Akkus verwenden, laden Sie nur diese. Das Laden von nicht wiederauﬂ adbaren Batterien kann die Batterien zur Explosion bringen, was Körperverletzung und Sachbeschädigung zur Folge haben kann.

Laden des Flugakkus

Einsetzen der Senderbatterien (RTF)

HINWEIS: Laden Sie Akkus nur, wenn sie auf Umgebungstemperatur abgekühlt sind. Schauen Sie sich den Akku an und stellen Sie sicher, dass dieser nicht beschädigt oder aufgequollen ist.

Stecken Sie den Lader in den USB Port. Schließen Sie den Akku an das Ladegerät.

Laden (LED rot) Fertig geladen (LED aus)

Entnehmen Sie den Akku immer aus dem Lader, sobald der Ladevorgang beendet ist.

ACHTUNG: Verwenden Sie nur Ladegeräte, die für LIPO Akkus vorgesehen sind. Nichtbeachtung kann zu Feuer, Beschädigungen oder Verletzungen führen.

ACHTUNG: Überschreiten Sie niemals die vorgesehene Ladezeit. ACHTUNG: Entnehmen Sie den Akku aus dem Lader, sobald dieser fertig geladen ist.

Belassen Sie den Akku niemals im Lader.

USB Li-Po Charger

EFLC1008

SOLID RED LED

–Charging

DC Input:5.0V 350mA DC Output:4.2V 300mA

LED OFF –Charge Complete

Einsetzen des Flugakkus

ACHTUNG: Trennen Sie den Li-Po-Akku immer vom Empfänger

des Flugzeugs wenn Sie nicht ﬂ iegen um eine Tiefentladung zu vermeiden. Akkus die unter die zulässige Mindestspannung entladen werden, können dadurch beschädigt werden, was sich in Leistungsverlust und potentieller Brandgefahr bei dem Laden bemerkbar machen kann.

1 Gas nach unten 2 Einschalten

Binden von Sender und Empfänger

Wenn Probleme auftreten beachten Sie bitte die Bindeanweisungen und schauen in die Hilfestellung zur Problemlösung. Kontaktieren Sie falls notwendig den technischen Service von Horizon Hobby. Eine Liste der kompatiblen DSM Sender sehen Sie unter www.bindnﬂ y.com.

Der Bindevorgang

1. Trennen Sie den Flugakku von ihrem Quadcopter.

2. Wählen Sie im Sender den Modelltyp Acro.

3. Zentrieren Sie im Sender alle Trimmungen.

4. Schalten Sie den Sender aus und reduzieren das Gas vollständig.

5. Installieren Sie den Akku im Quadcopter. Die LED auf der 3in1 Platine blinkt rot bei der Initialisierung

und dann blau, um Bindebereitschaft anzuzeigen.

6. Bringen Sie den Sender in den Bindemode während Sie ihn einschalten.

7. Lassen Sie den Bindeschalter nach 2 -3 Sekunden los. Der Quad-Copter ist gebunden wenn die blaue

LED auf der 3-in-1 Einheit leuchtet.

8. Trennen Sie den Flugakku und schalten den Sender aus.

MLP4DSM Bindeprozess

1. Trennen Sie den Flugakku vom Quadcopter.

2. Zentrieren Sie alle Trimmungen auf dem Sender.

3. Schalten Sie den Sender aus und reduzieren das Gas vollständig.

4. Installieren Sie den Akku im Quadcopter. Die LED auf der 3in1 Platine blinkt rot bei der Initialisierung

und dann blau, um Bindebereitschaft anzuzeigen.

5. Drücken Sie wenn die blaue LED blinkt den linken Steuerhebel ein während Sie den Sender ein-

schalten (Sie hören dabei ein Klick und einen langen Ton).

6. Lassen Sie den Stick los. Der Sender piept und die Power LED blinkt. Der Quad-Copter ist gebunden

wenn die LED auf der 3-in-1 Einheit blau leuchtet (nicht blinkt).

7. Trennen Sie den Flugakku und schalten den Sender aus.

Ihr RTF Sender ist bereits an das Modell gebunden. Sollten Sie neu binden wollen folgen Sie bitte den untenstehenden Anweisungen.

BNF-Sender

Wenn Sie einen Computersender verwenden, stellen Sie im Kanaleingabemenü den Kanal6 (Aux1) auf einen Taster, wie den Bindungsschalter (I). Stellen Sie den Modelltyp auf „Acro“ oder „Flugzeug“-Modus. Binden Sie den Quadcopter an Ihren Sender unter Beachtung der nachfolgenden Anweisungen.

Auswahl des Flugmodus

Zwischen den Flugmodi umschalten indem der linke Steuerknüppel auf MLP4DSM betätigt und freigeben wird oder durch Betätigen und Freigeben des Tasters auf Ihrem Computersender, wie im Abschnitt zur Bindung beschrieben.

• Stabilitätsmodus (blaue LED): die Schräglage ist begrenzt. Werden die Steuerknüppel losgelas-

sen, wird der Quadcopter in den Horizontalﬂ ug zurückkehren.

• Agilitätsmodus (rote LED): der Quadcopter verfügt über keine Begrenzung der Schräglage und

wird nicht in den Horizontalﬂ ug zurückkehren, wenn die Steuerknüppel losgelassen werden. Verwenden Sie Geschwindigkeiten und Exponential zum Einstellen der Leistung entsprechend Ihres Flugstils.

HINWEIS: Versuchen Sie nicht die Flugmodi während des Fliegens mit dem MLP4DSM-Sender zu ändern. Der Versuch wird dazu führen, dass der Sender eine fehlerhafte Mittelposition erkennt. Landen Sie immer den Quadcopter und lassen Sie die Steuerknüppel los, ehe Sie die Flugmodi ändern.

H A B C D E F

Modus

Querruder

(links/rechts)

Gas (auf/ab)

Gas trimm

Querrudertrimm

Seitenrudertrimm

Höhenrudertrimm

Seitenruder

(links/rechts)

Höhenruder

(auf/ab)

Modus

Querruder

(links/rechts)

Höhenruder

(auf/ab)

Höhenrudertrimm

Querrudertrimm

Seitenrudertrimm

Gas trimm

Seitenruder

(links/rechts) Gas (auf/ab)

Sendersteuerung (RTF)

Auswahl Dual Rate

Auswahl

Dual Rate

EIN/AUS-Schalter

Ein/Aus-LED

Wenn die Trimmtasten gedrückt werden, geben sie einen Signalton von sich, der bei jedem erneuten Drücken höher oder tiefer wird. Die mittlere oder neutrale Trimmstellung erklingt in der mittleren Tonhöhe. An den äußeren Enden des Steuerbereichs erklingt eine Tonfolge.

Seitenruder

Erklärung der Flugkontrollen

Bitte nehmen Sie sich vor dem Erstﬂ ug des Inductrix Quadcopter Zeit um sich mit den Kontrollen vertraut zu machen.

Gasgeber

Seitenruder

nach links

Nase dreht nach rechts

Nase dreht nach links

Gasgeber

nach oben

Seitenansicht Seitenansicht

Sinken

Aufsteigen

Gasgeber

nach unten

Seitenruder nach rechts

Dual Rate (RTF)

Der Glimpse RTF Quadcopter wird mit dem Blade MLP4DSM Sender geliefert.

• Wenn Sie den Sender einschalten, beﬁ ndet sich im Dual Rate in Max.

• Die Dual Rate Einstellung ändern Sie durch drücken des rechten Knüppels.

• Im Low Rate Mode mit den kleinen Ruderausschlägen ist der Copter in der Schräglage limitiert und richtet sich selber aus wenn die Steuerhebel los gelassen werden. Dieser Mode ist für Piloten geeignet die für die ersten Flüge gutmütige Reaktionen und einfache Kontrolle erwarten.

• Im High Rate Mode ist die mögliche Schräglage größer, der Copter richtet sich aber noch selber auf wenn die Steuerhebel losgelassen werden.

Dual Rate Auswahl

Auswahl des

Bindungs-/ Flugmodus

+ 4 hidden pages