Blade 200 SRX Instruction Manual
RTF
READY-TO-FLY
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni
2
EN
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before
operating. Failure to operate the product correctly can result in damage to the product, personal property and
cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage
to the product or other property. This product is not intended for use by children without direct adult supervision. Do
not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow
all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid
damage or serious injury.
The following terms are used throughout the product literature to indicate various levels of potential harm when
operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no
possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a
possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,
and serious injury OR create a high probability of superfi cial injury.
• Always keep a safe distance in all directions around
your model to avoid collisions or injury. This model is
controlled by a radio signal subject to interference from
many sources outside your control. Interference can
cause momentary loss of control.
• Always operate your model in open spaces away from
full-size vehicles, traffi c and people.
• Always carefully follow the directions and warnings for
this and any optional support equipment
(chargers, rechargeable battery packs, etc.).
• Always keep all chemicals, small parts and anything
electrical out of the reach of children.
• Always avoid water exposure to all equipment not
specifi cally designed and protected for this purpose.
Moisture causes damage to electronics.
• Never place any portion of the model in your mouth as it
could cause serious injury or even death.
• Never operate your model with low transmitter
batteries.
• Always keep aircraft in sight and under control.
• Always move the throttle fully down at rotor strike.
• Always use fully charged batteries.
• Always keep transmitter powered on while aircraft is
powered.
• Always remove batteries before disassembly.
• Always keep moving parts clean.
• Always keep parts dry.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Never operate aircraft with damaged wiring.
• Never touch moving parts.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon
Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
Safety Precautions and Warnings
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in
a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to
ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards,
but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with
DSM or Spektrum.
3
EN
First Flight Preparation .....................................................4
Flying Checklist ...............................................................4
Charging Warnings...........................................................4
Battery Charging ..............................................................5
Installing the Transmitter Batteries (RTF) ..........................5
Transmitter Setup Table ...................................................6
Installing the Flight Battery ..............................................7
Transmitter and Receiver Binding .....................................7
SAFE Technology .............................................................8
Panic Recovery ................................................................8
Transmitter Control ..........................................................9
Flight Mode and Rate Selection ........................................9
Control Tests ..................................................................10
Understanding the Primary Flight Controls .....................11
Flying the 200 SR X .......................................................12
Post-Flight Inspection and Maintenance Checklist ..........12
Troubleshooting Guide ...................................................13
Exploded View ...............................................................14
Parts Listings .................................................................14
Limited Warranty ...........................................................15
Warranty and Service Contact Information .....................16
FCC Information .............................................................16
IC Information ...............................................................16
Compliance Information for the European Union .............17
Box Contents
• Blade 200 SR X
• 800mAh 3S 11.1V 30C Li-Po Battery
• 3S Li-Po Balancing Charger with AC to DC Adapter
• LP6DSM SAFE Transmitter (RTF Only)
• 4 AA Batteries (RTF Only)
Table of Contents
Length
14.76 in (375mm)
Height
5.31 in (135mm)
Main Rotor Diameter
16.14 in (410mm)
Tail Rotor Diameter
3.25 in (82.5mm)
Flying Weight
8.82 oz (250 g)
Specifications
Features RTF BNF
Airframe – Blade® 200 SR X Included Included
Main Motor - 3900Kv Brushless Installed Installed
Tail Motor - 5100Kv Brushless Installed Installed
Recevier - Spektrum™ AR636H Receiver Installed Installed
ESC - Dual Brushless ESC Installed Installed
Battery – 800mAh 3S 11.1V 30C Li-Po Included Included
Charger – 3S 0.8A Li-Po Balancing Charger with AC to DC Adapter Included Included
Transmitter – LP6DSM SAFE
™
Transmitter Included Required
To register your product online,visit www.bladehelis.com
4
EN
The battery charger (EFLC3105) included with your
helicopter has been designed to safely charge the Li-Po
battery.
CAUTION: All instructions and warnings must be
followed exactly. Mishandling of Li-Po batteries
can result in a fi re, personal injury and/or property
damage.
• By handling, charging or using the included Li-Po battery,
you assume all risks associated with lithium batteries.
• If at any time the battery begins to balloon or swell,
discontinue use immediately. If charging or discharging,
discontinue and disconnect. Continuing to use, charge or
discharge a battery that is ballooning or swelling can result
in fi re.
• Always store the battery at room temperature in a dry area
for best results.
• Always transport or temporarily store the battery in a
temperature range of 40–120º F (5–49° C). Do not store the
battery or model in a car or direct sunlight. If stored in a hot
car, the battery can be damaged or even catch fi re.
• Always charge batteries away from fl ammable materials.
• Always inspect the battery before charging.
• Always disconnect the battery after charging, and let the
charger cool between charges.
• Always constantly monitor the temperature of the battery
pack while charging.
• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE
LI-PO BATTERIES. Failure to charge the battery with a
compatible charger may cause a fi re resulting in personal
injury and/or property damage.
• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
• Never leave charging batteries unattended.
• Never charge batteries outside recommended levels.
• Never charge damaged batteries.
• Never attempt to dismantle or alter the charger.
• Never allow minors to charge battery packs.
• Never charge batteries in extremely hot or cold places
(recommended between 40–120° F or 5–49° C) or place in
direct sunlight.
Charging Warnings
First Flight Preparation
• Remove and inspect contents
• Begin charging the fl ight battery
• Install the fl ight battery in the helicopter
(once it has been fully charged)
• Program your computer transmitter (BNF only)
• Bind your transmitter (BNF only)
• Familiarize yourself with the controls
• Find a suitable area for fl ying
Flying Checklist
❏ Always turn the transmitter on fi rst
❏ Plug the fl ight battery into the lead from the ESC
❏ Allow the receiver and ESC to initialize and arm properly
❏ Fly the model
❏ Land the model
❏ Unplug the fl ight battery from the ESC
❏ Always turn the transmitter off last
5
EN
NOTICE: Charge only batteries that are cool to the touch and
are not damaged. Look at the battery to make sure it is not
damaged e.g., swollen, bent, broken or punctured.
1. Connect the AC to DC adapter to an AC outlet.
2. Connect the AC to DC adapter to the charger.
3. Connect the battery balance lead to the charger.
The connector is keyed to prevent reverse
polarity connection.
4. Always disconnect the fl ight battery from the charger
immediately upon completion of charging.
LED Indicators
Red Flashing LED: Input power with no battery connected
R ed and Green Solid LEDs: Battery connected and
charging
Red Solid LED: Charge complete
Red and Green Flashing LEDs: Charge error
Charging a fully discharged (not over-discharged) 800mAh battery takes approximately 1–1.5 hours.
The charger can also be powered through the DC alligator clips. Connect them to a 11.5–15V DC power source, noting
proper polarity.
CAUTION: Do not connect to AC and DC power sources at the same time. Doing so may cause a short circuit,
resulting in damage to the product, personal injury or property damage.
NOTICE: Always connect cable polarities correctly. Consult the battery instructions, safety sheet or product support before
using a 12V battery with sources other than a standard AC wall outlet.
Installing the Transmitter Batteries (RTF)
Replace the transmitter batteries
when the transmitter beeps.
Battery Charging
6
EN
Transmitter
Model
Type
Setup /
Channel
Assignments Reversing Setup Flight Modes Dual Rates
Hgh
Rate
Low
Rate Other Settings
MLP6DSM N/A
DIP Switches:
1, 2, 4, 5, 6, 7,
9, and 10 = OFF
3 and 8 = ON
N/A
CH 5 Pos 0 = Beginner
Default
100%
Fixed
70%
Fixed
CH 5 Pos 1 = Intermediate
CH 5 Pos 2 = Experienced
DX4e (New)
w/ 3 Position
Switch
N/A MIX=NOR All channels = NORM
CH 5 Pos 0 = Beginner
Ail/Ele/Rud
100%
Fixed
70%
Fixed
CH 5 Pos 1 = Intermediate
CH 5 Pos 2 = Experienced
DX5e (New)
w/ 3 Position
Switch
N/A MIX=NOR All channels = NORM
CH 5 Pos 0 = Beginner
Ail/Ele/Rud
100%
Fixed
70%
Fixed
CH 5 Pos 1 = Intermediate
CH 5 Pos 2 = Experienced
DX7/7SE Acro
Gear=INH
Flap=GEAR
Trainer=Aux1
AUX1 = REV
Throttle Travel =
85% Low, 100% Full
Gyro Switch Pos 0 = Beginner
Ail D/R switch = Ail D/R
Ele D/R switch = Ail D/R
Rud D/R switch = Ail D/R
100% 70%
Timer
Count Down
08:00 Tone
Start: Throttle Out
Pos: 25%
Gyro Switch Pos 1 = Intermediate
Gyro Switch Pos 2 = Experienced
DX8 Acro
Flap=INH
Trainer=AUX1
Gear=INH
F Mode=Gear
AUX1 = REV
All Others = NORM
Throttle Travel =
85% Low, 100% Full
Switch B Pos 0 = Beginner
Ail D/R switch = Ail D/R
Ele D/R switch = Ail D/R
Rud D/R switch = Ail D/R
100% 70%
Timer
Count Down
08:00 Tone
Start: Throttle Out
Pos: 25%
Switch B Pos 1 = Intermediate
Switch B Pos 2 = Experienced
DX9/DX18 Acro
Channel Input
Confi g
5 GEAR = B
6 AUX 1 = I
AUX1=REV
Throttle Travel =
85% Low, 100% Full
Switch B Pos 0 = Beginner
Ail D/R switch = Ail D/R
Ele D/R switch = Ail D/R
Rud D/R switch = Ail D/R
100% 70%
Timer
Count Down
08:00 Tone
Start: Throttle Out
Switch B Pos 1 = Intermediate
Switch B Pos 2 = Experienced
Transmitter Setup Table
Loading...