1
OWNERS MANUAL
Standard Features
The following features are standard with your
RAS 200 Remote Start:
Two button remote control(s)*
Status Indicator (LED)
Valet/Service mode switch
Remote Start capabilities
Remote Heater/AC capabilities
Parking Light Verification
Safety Inputs (Brake & Hood)
Remote Shutdown Operation
Extended Range Receiver
Stop & Go
Auto Cold Start (Protected)
*S models provided with single transmitter.
Optional Features that you may
add to your RAS 200 (Consult with your
technician)
Remote Keyless Entry (Door
Lock/Unlock)
Trunk/Hatch Release
Window Roll-up
Note: Some features and options may
require additional parts and labor or may not
be appropriate for certain vehicles.
Automatic Transmission and Electronic Fuel
Injection is required on vehicles for Remote
Start products.
System Operation
Important: Do not operate this remote
auto start in an enclosed garage or area
without proper ventilation. Be sure to familiarize yourself with the features of the
Remote Auto Start Product prior to using the
product.
PROGRAM SWITCH:
The RAS is equipped with a program
switch.This program switch is usually
mounted in a convenient location under
or around the lower dash. If you can not
locate it, ask your installing dealer to
show you it’s location. If you desire to put
your Remote Auto Start in Service Mode;
this will allow you to use the optional
keyless entry features only, the vehicle
will not start with the remote control.
To enter the service mode:
1.Turn
ignition
to the
ON posi-
RAS 200
Button 1 LED Button 2
••
•
••
•
Button 2 LED Button 3
Button 1
2- Button
Transmitter
3- Button
Transmitter
+
ON
Press
+
Hold
tion.
2. Press and hold the programswitch for 5
seconds.The LED will turn on solid. 3.
Turn ignition off.
To exit
the service
mode:
1.Turn ignition to the ON Position. 2.
Press and hold the program switch for 5
seconds.The LED will turn off. 3.Turn
ignition off.
REMOTE STARTING
THE VEHICLE:
Press button #1 on the
remote transmitter.The
parking lights will come on
solid.Approximately 2 seconds later the RAS will
attempt to start the vehicle,
the LED will flash rapidly.
Once the car has started, the heater or
air conditioner will turn on (as long as it
is set to run prior to exiting the vehicle),
it will run for the programmed time (12
or 24 minutes). If the engine fails to start
on the first attempt, it will repeat the
starting procedure 2 more times. If the
vehicle fails to start after a total of 3
times the Parking lights will flash 4 times.
The doors will lock at this time (optional
feature).
Driving the vehicle after remote
started:
Unlock the door by pressing button #2 on remote
transmitter (optional). Enter
vehicle, turn ignition key to
the on position (Note: Do
not turn the key all the way to
the start position as you may
damage the starter).
Once the ignition key is turned to the on
position, press the brake pedal and shift
the car into the proper gear and you may
now drive the vehicle (Note: If brake
pedal is pressed prior to turning ignition on,
engine will turn off).
Remote engine shutdown:
If the vehicle has been remotely started
and you desire to turn the vehicle off,
simply press button #1 on the remote
transmitter.After the motor has turned
off the doors will relock (optional).
ENGAGING AUTO COLD
START ACTIVATION:
This feature will start the car every 2
hours for a predetermined time (12 or 24
minutes).
To activate this feature:
Simultaneously hold the
program switch and button
#2 on the remote for 5
seconds.The parking lights
will flash 5 times and stay
on for 30 seconds.The
2
+
ON
Press
+
Hold
Press
••
•
••
•
Press
Press
••
•
••
•
Press
or
or
Press
••
•
••
•
Press
or
Loading...