Blackstone 1923 Manual

MODELS:   

ENGLISH

v19

OWNER’S MANUAL

36" GRIDDLE

AIRFRYER COMBO

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . .

ASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

USING YOUR BLACKSTONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IMPORTANT:

This instruction manual contains important information necessary for the proper assembly and safe use of the appliance.

Read and follow all warnings and instructions before assembling and using the appliance.

Follow all warnings and instructions when using the appliance.

Keep this manual for future reference.

Installer/Assembler: Leave these instructions with the consumer.

For the latest version of this manual, scan this code or visit

BlackstoneProducts.com/support

SAFETY ALERT KEY

 DANGER

Indicates a hazardous situation that, if not avoided, will result in death or serious injury.



CAUTION

Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

 WARNING

Indicates a hazardous situation that, if not avoided, could result in death or serious injury.

NOTICE

Indicates information considered important, but not hazardrelated (e.g. messages related to property damage).

BLACKSTONEPRODUCTS.COM/SUPPORT

| CONTACT CUSTOMER SUPPORT BEFORE RETURNING APPLIANCE TO RETAILER.



OWNER’S MANUAL | IMPORTANT SAFETY INFORMATION

PELLET GRILL SAFETY

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET FUEL-BURNING APPLIANCE. FAILURE TO FOLLOw THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.

SAVE THESE INSTRUCTIONS.

• Burning wood gives o carbon monoxide which can cause death.

• DO NOT burn wood chips inside homes, vehicles, tents, garages or any enclosed areas.

• Use only outdoors where it is well ventilated.

IMPORTANT SAFETY INFORMATION

ENGLISH

MODELS:   

 DANGER

If you smell gas:

• Shut o gas to the appliance.

• Extinguish any open flame.

• Open hood (if applicable).

• If odor continues, keep away from the appliance

and immediately call your gas supplier or your fire department.

Failure to follow these instructions could result in fire or property damage, personal injury or death.

 DANGER

• NEVER operate this appliance unattended.

• If a fire should occur, keep away from the appliance and

immediately call your fire department. DO NOT attempt to extinguish an oil or a grease fire with water.

Failure to follow these instructions could result in fire or property damage, personal injury or death.

ELECTRIC APPLIANCE SAFETY

TO PROTECT AGAINST ELECTRIC SHOCK:

• DO NOT immerse cord or plugs in water or other liquid.

• Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking o parts.

• DO NOT use an outdoor cooking gas appliance for purposes other than intended.

• DO NOT operate this appliance with a damaged cord, plug, or after the appliance malfunctions or has been damaged in any manner. Contact the manufacturer for repair.

• DO NOT let the cord hang over the edge of a table or touch hot surfaces.

• Keep any electrical supply cord and the fuel supply hose away from heated surfaces.

• When connecting, first connect plug to the appliance then into the outlet.

USE ONLY A GROUND FAULT INTERRUPTER (GFI) PROTECTED CIRCUIT wITH THIS APPLIANCE.

• This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with NFPA 70 Canadian Electrical Code, Part I.

• DO NOT remove the grounding plug or use with an adapter of 2 prongs.

• Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved for outdoor use with a W-A marking.

 WARNING

• DO NOT store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.

• An LPG cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

GAS APPLIANCE SAFETY

• The use of alcohol, prescription, or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate the appliance.

• Keep children and pets away from the appliance at all times.

• Have a type BC or ABC fire extinguisher readily available.

DO NOT USE FOR PURPOSES OTHER THAN INTENDED.

• DO NOT use for commercial cooking.

• DO NOT use this appliance as a heater.



WARNING

Improper installation, use, adjustment, alteration, service, modification, or maintenance can cause injury or property damage. Refer to this manual.

INSTALLATION MUST CONFORM wITH LOCAL CODES.

In the absence of local codes, installation must conform with

ANSI Z223.1/NFPA 54, CSA B149.1, or CSA B149.2.

either

FOR OUTDOOR USE ONLY.



BLACKSTONEPRODUCTS.COM/SUPPORT

MODELS:   

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

01.

DO NOT touch hot surfaces. Use handles or knobs.

02.

To protect against electrical shock DO NOT immerse cord, plugs, or appliance in water or other liquid.

03.

Close supervision is necessary when any appliance is used by or near children.

04.

Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking o parts.

05.

DO NOT operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, or adjustment.

06.

The use of accessory attachments not recommended by the appliance manufacturer may cause injuries.

07.

DO NOT let cord hang over edge of table or counter, or touch hot surfaces.

08.

DO NOT place on or near a hot gas or electric burner, or in a heated oven.

09.

Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.

10.

To disconnect, turn any control to “o’, then remove plug from wall outlet.

11.

DO NOT use appliance for other than intended use.

12.

Fuel, such as charcoal briquettes, is not to be used with appliance.

13.

Use only on properly grounded outlet.

14.

CAUTION: Risk of Electric Shock. Keep extension cord



connection dry and o the ground.

15.

The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

16.

Children should be supervised to ensure that they DO NOT play with the appliance.

17.

For outdoor use only, DO NOT expose to rain.

18.

Be sure that handles are assembled and fastened properly.

| OWNER’S MANUALIMPORTANT SAFETY INFORMATION

FOR ExTENSION CORDS:

a. A short power-supply cord is provided to reduce the risk resulting

from becoming entangled in or tripping over a longer cord.

b. Longer power-supply cords or extension cords are available and

may be used if care is exercised in their use.

c. If a longer power-supply cord or extension cord is used:

01.

The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance.

02.

The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally.

03.

The cord set or extension cord should be a grounding-type 3-wire cord.

d. Outdoor extension cords should be used with outdoor use appli-

ances and are surface marked with the suix letter “W” and with a tag stating “Suitable for use with outdoor appliances.”

e. The connection to an Extension cord should be kept dry and o the

ground.

f. Store appliance indoors when not in use - out of the reach of

children.

g. DO NOT clean this product with a water spray or the like.

ENGLISH

SAVE THESE INSTRUCTIONS

 WARNING

DO NOT operate this appliance unattended.

BLACKSTONEPRODUCTS.COM/SUPPORT



OWNER’S MANUAL | ASSEMBLY GUIDE MODELS:   

PARTS

Control knob bezels



Electric ignitor



PARTS

Griddle tubular

 Gas rail & Valves



PARTS

Motor switch



Air fryer H burner



PARTS

Hood



Air fryer drawer front



ASSEMBLY GUIDE

ENGLISH

ExPLODED VIEw

2.2 43 44

6 5

1.3a

1.1

1.2a 1.2b

41

2.1 42

19 46 27

1.3b

1.4

1.7

21

14 22

9

28 24 36

1.8

23 24

45 25 26

20

1.6 39 37

3 7. 1

1

11

7

30

17 16 31

13

3

3 7. 2

38

16

1.5

15

8

30

10 31

34 33 29

PARTS LIST

1.1

1.2a

1.2b

Electric ignitor wire (5pcs per set) with electrode



QTY



1.3a

burners

1.3b

1.4

Regulator hose 

1.5

Air fryer control knob bezel

QTY



1.6

1.7

1.8

Motor assembly 

1.9

Power cord 

2.1

Griddle top 

QTY

2.2

3 7. 1

panels

3 7. 2

Silicone pads (4 pcs per pack)

BLACKSTONEPRODUCTS.COM/SUPPORT

QTY



| OWNER’S MANUALASSEMBLY GUIDEMODELS:   

ENGLISH

1

Griddle body (1 piece)

5

Hood handle

(1 piece)

11

Top cart panel

(1 piece)

17

Middle cart

panel (1 piece)

6

Hood handle

standos (2 pieces)

12

Back cart panel

(1 piece)

18

Right cart panel

(1 piece)

2

Griddle top & hood (1 piece)

7

Left-rear leg

(1 piece)

13

Left cart panel

(1 piece)

19

Left side shelf

(1 piece)

8

Right-rear leg

(1 piece)

14

Crossbar

assembly (1 piece)

20

Right side shelf

(1 piece)

3

Cart base

(1 piece)

9

Left-front leg

(1 piece)

15

Garbage bag

holder (1 piece)

21

Hose retainer

(1 piece)

4

Matchstick

holder (1 piece)

10

Right-front leg

(1 piece)

16

Paper towel

holder (1 piece)

22

LPG hook

(1 piece)

23

LPG support

(1 piece)

29

Control knobs

(5 pieces)

35

Motors

(2 pieces)

41

Aluminum grease cup liner (1 piece)

24

LPG support

bracket (1 piece)

30

Cart drawer

assembly (2 pieces)

36

Motor shells and

brackets (2 pieces)

42

Grease cup

(1 piece)

25

Cutting board

(1 piece)

31

Cart drawer

front panels (2 pieces)

37

Air fryer drawer

assembly (3 pieces)

43

Hood hinge

lever 1 (2 pieces)

26

Magnetic strip

(1 piece)

32

Cart door

(1 piece)

38

Air fryer drawer

handles (3 pieces)

44

Hood hinge

lever 2 (2 pieces)

27

Shelf hooks

(3 pieces)

33

Cart door/ drawer handles (3 pieces)

39

Air fryer drawer trivets (3 pieces)

45

Shelf bracket (A) (2 pieces)

28

Lockable caster

wheels (4 pieces)

34

Cart door/ drawer handle bezels (6 pieces)

40

Power cord bracket (1 piece)

46

Shelf bracket (B) (2 pieces)

BLACKSTONEPRODUCTS.COM/SUPPORT



OWNER’S MANUAL | ASSEMBLY GUIDE

NOTICE

Place appliance on a heat-resistant and flame-resistant surface while in use.

TOOLS NEEDED:

#3 Phillips head screwdriver & Adjustable wrench

TOOL NEEDED:

#3 Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

NOT INCLUDED:

One (1) AA battery (for ignition) Optional four (4) AA batteries

(for the motor)

TOOL NEEDED:

#3 Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

ENGLISH

47

Hardware pack (1 piece)

a. M6x12 screws (24 pieces) b. M5x10 screws (34 pieces) c. Long M6 shoulder bolts (4 pieces) d. M6x15 screws (8 pieces) e. M5 step bolts (4 pieces) f. M6 thumbscrews (4 pieces) g. M6x15 screws (6 pieces) h. Spares i. Long M6 step bolts (8 pieces) j. M5x15 screws (12 pieces) k. Short M6 step bolts

[a.]

[b.] [c.]

[d.]

[e.]

[f.]

MODELS:   

ASSEMBLY INSTRUCTIONS

Find a large, clean area to assemble your appliance. Remove all packing material before assembling.

 CAUTION

Sharp edges. Wear gloves while assembling.

[g.]

[i.]

[h.]

[j.]

[k.]

 CAUTION

Heavy pieces. Two people should assemble this appliance.

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg) LPG cylinder must include collar to

protect LPG cylinder valve.



NOT INCLUDED:

AA battery & Ten (10) #2032 cell batteries

TOOLS NEEDED:

#3 Phillips head screwdriver &

ELECTRIC REQUIREMENTS:

120V 60Hz

Adjustable wrench

BLACKSTONEPRODUCTS.COM/SUPPORT

| OWNER’S MANUALASSEMBLY GUIDEMODELS:   

ENGLISH

STEP 01

Turn the cart base upside down and screw on the four (4) lockable caster wheels. (Ensure that the wheels are locked before attaching them.)

STEP 03

Use five (5) M6x12 screws [a.] to attach the right cart panel and middle cart panel to the bottom tray. (Note: the magnets should face the front.)

STEP 02

Use three (3) M6x12 screws [a.] to attach the left cart panel

to the cart base.

[a.] × 3

front left door hinge pin

STEP 04

Use six (6) M5x10 screws [b.] to attach the back cart panel to

the left cart panel, middle cart panel and right cart panel.

[a.] × 5

front left door hinge pin

STEP 05

Use eight (8) M5x10 screws [b.] to attach the top cart panel to the left cart panel, middle cart panel and right cart panel.

[b.] × 6

[b.] × 8

BLACKSTONEPRODUCTS.COM/SUPPORT



OWNER’S MANUAL | ASSEMBLY GUIDE MODELS:   

[b.] × 4

ENGLISH

STEP 06

Use four (4) M6x12 screws [a.] to attach the left-front leg and

left-rear leg to the cart base. (Note: the front leg is shorter than the rear leg.)

STEP 07

Use four (4) M6x12 screws [a.] to attach the right-front leg

and right-rear leg to the cart base. (Note: the front leg is shorter than the rear leg.)

[a.] × 4

STEP 08

Use four (4) M5x10 screws [b.] to attach the crossbar

assembly to the left-front and left-rear legs.

STEP 09

With the help of another person, set the griddle body upside down. With the help of another person, slide the cart legs into the slots of the griddle body. Use six (6) M6x12 screws [a.] to attach the legs to the griddle body. Use four (4) thumb screws [f.] to attach the legs to the air fryer body. (DO NOT fully tighten screws at this time.)

[a.] × 6

[f.] × 4



BLACKSTONEPRODUCTS.COM/SUPPORT

| OWNER’S MANUALASSEMBLY GUIDEMODELS:   

[b.] × 2

[a.] × 2

ENGLISH

STEP 10

With the help of another person, set the griddle on its feet

and tighten the screws.

STEP 12

Use two (2) M5x10 screws [b.] to attach the paper towel

holder to the right-front leg.

STEP 11

Unscrew the two (2) M6x12 screws from the right side of the griddle, then use these screws to attach the power cord bracket to the right side of the griddle.

STEP 13

Use two (2) M6x12 screws [a.] to attach one (1) cart door/ drawer handle and two (2) bezels to the cart door.

STEP 14

Attach the cart door assembly to the cart by first inserting the door into the lower door hinge pin, then down and inserting the upper door hinge pin.

BLACKSTONEPRODUCTS.COM/SUPPORT

pressing

❷

❶



OWNER’S MANUAL | ASSEMBLY GUIDE

Make sure the front pins are seated in the holes, then push the griddle top back.

Make sure the front pins are fully seated in the holes, then push the griddle top forward to lock the griddle in place.

[b.] × 14

ENGLISH

STEP 15

Use seven (7) M5x10 screws [b.] to attach the cart drawer

front panel to the cart drawer body. Repeat this step with the other drawer.

MODELS:   

STEP 16

Use two (2) long step bolts [i.] to attach one (1) cart door/

drawer handle and two (2) bezels to the cart drawer front panel. Repeat this step with the other drawer.

[i.] × 4

STEP 17

Pull out the four (4) cart sliding tracks from the middle and

right cart panels. Insert the drawer sliding tracks into the cart tracks.

STEP 18

With the help of another person, place the griddle top and

hood on the griddle body by aligning the four (4) pins to the holes of the body.

Make sure the front pins are seated in the holes, then push the griddle top back.



BLACKSTONEPRODUCTS.COM/SUPPORT

| OWNER’S MANUALASSEMBLY GUIDEMODELS:   

ENGLISH

STEP 19

Use three (3) M6x15 screws [g.] to attach the LPG support bracket to the left cart panel.

[g.] × 3

STEP 20

Use one (1) M6x15 screw [g.] to attach the LPG hook to the left leg assembly. Use one (1) M6x15 screw [g.] to assemble the hose retainer. Use one (1) M6x15 screw [g.] to attach the LPG support to the LPG support bracket.

[g.] × 3

STEP 21

Slide the hood handle into the two (2) hood handle stand-

os. Use four (4) long M6 shoulder bolts [c.] to attach the handle to the front of the hood.

STEP 22

body using eight (8) M6x15 screws [d.]. Use one left shelf bracket (A) and one right shelf bracket (B).

[c.] × 4 [d.] × 8

Attach the four (4) side shelf brackets to the sides of the

A

B

A

B

BLACKSTONEPRODUCTS.COM/SUPPORT



OWNER’S MANUAL | ASSEMBLY GUIDE MODELS:   

[j.] × 4

ENGLISH

STEP 23

Unscrew the three (3) M6x8 screws from the side shelf pegs. Use the (3) M6x8 screws to attach the three (3) side shelf pegs to the left side shelf.

STEP 24

Thread two (2) short M6 step bolts [k.] into the top holes on

the left side shelf. Repeat with the right side shelf.

[k.] × 4

STEP 25

Slide the left side shelf onto the side shelf brackets. The threaded M6 step bolts will hook and hold the shelf.

Use two (2) short M6 step bolts [k.], to secure the shelf to the griddle body by screwing them into the bottom holes of the bracket.

Repeat this step with the right side shelf.

[k.] × 4

STEP 26

Attach the drawer handle:

Remove the two small thumb screws from inside the drawer to remove the front panel of the drawer.

Use four (4) M5x15 screws [j.] to attach the drawer handle to

the front panel. Be sure to install handle correctly, with the handle facing down.

Re-attach the front panel with the previously removed thumb screws.

Repeat this step with the other two (2) drawers.



BLACKSTONEPRODUCTS.COM/SUPPORT

| OWNER’S MANUALASSEMBLY GUIDEMODELS:   

ENGLISH

STEP 27

Place the cutting board onto the right side shelf.

STEP 28

Install the control knob batteries:

For each of the control knobs, unscrew the two (2) M3x8 screws to open the base.

Insert two (2) #2032 cell batteries (not included) into the battery socket with the positive + terminal facing inside.

Reattach the base.

-

+

STEP 29

Install the five (5) control knobs by pushing them into place

in the OFF position.

STEP 30

Thread two (2) M5x15 step bolts [e.] into the lower holes

of the right legs.

Use two (2) M5x15 step bolts [e.] to attach the garbage bag

holder to the right legs.

[e.] × 4

BLACKSTONEPRODUCTS.COM/SUPPORT



ENGLISH

NOTICE

Place appliance on a heat-resistant and flame-resistant surface while in use.

OWNER’S MANUAL | ASSEMBLY GUIDE

STEP 31

Turn the paper towel hanger 90º.

STEP 32

Hang the rear grease cup with aluminum foil liner on the

back of the unit.

MODELS:   

STEP 33

Use the left screw on the logo panel to attach the match

stick holder.

STEP 34

Proceed to USING YOUR BLACKSTONE.

NOTICE

• Maximum weight on the side shelf is 10 lbs (4.5 kg).

• The side shelf may get hot while appliance is in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while cooking.



BLACKSTONEPRODUCTS.COM/SUPPORT

MODELS:   

USING YOUR BLACKSTONE

| OWNER’S MANUALUSING YOUR BLACKSTONE

ENGLISH

BEFORE COOKING

CHECK BURNERS

Prior to connection and use, ensure that there is no debris caught in, or damage to, the head of the gas cylinder, regulator, hose, burner and burner ports.

Spiders and insects can nest within and clog the burner/venturi tube at the orifice.

Please reference the Troubleshooting chapter for burner cleaning instructions.

Blocked burner

Venturi

Air intake

Fuel nozzle



rail fuel nozzle orifice is correctly engaged within the burner opening.

Burner opening

 DANGER

Flammable items can combust if placed near the appliance. Keep the appliance area clear and free from combustible

materials, aerosol containers, gasoline and other flammable vapors and liquids.

 WARNING

A clogged burner can lead to a fire beneath the appliance.

Burner should be removed and cleaned whenever blockages are found.

Ensure that the gas

SETTING UP YOUR OUTDOOR SPACE

THIS APPLIANCE MUST ONLY BE USED OUTDOORS.

• DO NOT use this appliance inside buildings, garages, or any other

enclosed area.

• DO NOT install this appliance in or on a boat.

• DO NOT install this appliance in or on a recreational vehicle.

MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL.

• DO NOT use this appliance on or under any apartment or condo-

minium balcony or deck.

• DO NOT obstruct the flow of combustion and ventilation air.

• DO NOT operate this appliance any closer than 36 in (1 m) from the

sides and back of the appliance to combustible construction.

A

A = 36 in (1 m)

A

• DO NOT use this appliance under overhead combustible

construction.

SHELTERED OUTDOOR AREAS:

All openings must be permanently open; sliding doors, garage doors, windows or screened openings are not considered as permanent openings.

An appliance is considered to be outdoors if installed with shelter no more inclusive than:

a. With walls on three sides, but

with no overhead cover.

A

THE MINIMUM AMBIENT OPERATING TEMPERATURE IS 0°F (-18°C).

b. Within a partial enclosure that

includes an overhead cover and no more than two sidewalls. The sidewalls may be parallel, as in a breezeway, or at right angles to each other.

c. Within a partial enclosure that

includes an overhead cover and three sidewalls, as long as 30% or more of the horizontal periphery of the enclosure is permanently open.

Both ends open

30%

BLACKSTONEPRODUCTS.COM/SUPPORT



OWNER’S MANUAL | USING YOUR BLACKSTONE

ENGLISH

LPG CYLINDER REQUIREMENTS

FOR 20 LB (9 KG CYLINDERS)

• The LPG supply cylinder to be used must be constructed and marked in accordance with the specifications for LP gas cylinders, U.S. Department of Transportation (DOT) or the Standard for Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods, CAN/CSA-B339.

• Only LPG cylinders marked “propane” shall be used.

• The LPG cylinder supply system must be arranged for vapor withdrawal.

•

Always keep new LPG cylinders in upright position during use, transit or storage.

•

Always keep the ventilation opening(s) of the cylinder enclosure free and clear from debris.

THE LPG CYLINDER VALVE MUST HAVE:

• Type 1 valve outlet (thread on the outside).

• Safety relief valve.

• UL listed Overfill Protection Device (OPD). This OPD safety feature is identified by a unique triangular hand wheel.

• Dust cap.

OPD hand wheel

Type 1 valve outlet

Safety relief valve

(check seal before use)

MODELS:   

FILLING & ExCHANGE

• Use only those reputable exchange companies that inspect, precision fill, test and certify their cylinders. LPG dealer must purge new cylinder before filling.

• Volume of propane in cylinder will vary by temperature.



WARNING

A frosty regulator indicates gas overfill. Immediately close LPG cylinder valve and call local LPG

dealer for assistance.

• DO NOT release liquid petroleum gas (LPG) into the atmosphere.

• To remove gas from LPG cylinder, contact a certified LPG dealer or local fire department for assistance.

• Exchange cylinder only for an OPD safety feature-equipped cylinder.

Your retailer can help you match a replacement LPG cylinder to your appliance.

LEAK TEST INSTRUCTIONS

• Leak test new and exchanged LPG cylinders BEFORE connecting to griddle.

• DO NOT smoke during leak test.

• DO NOT use an open flame to check for gas leaks.

• Appliance must be leak tested outdoors in a well-ventilated area, away from ignition sources such as gas fired or electrical appliances.

• During leak test, keep appliance away from open flames or sparks.

Dust cap

The seal on the type 1 valve outlet could, over time, show marked and visible damage or deterioration that might cause a leak even with the connection tightened.

• A visual inspection for the seal must be carried out every time a LPG cylinder is replace or refilled.

• Any LPG cylinder showing signs of damage or deterioration as those illustrated including visible cracks and pitting, must be returned unused to the seller.

STORING LPG CYLINDERS

 WARNING

• DO NOT store a spare LPG cylinder under or near this appliance.

• DO NOT fill an LPG cylinder beyond 80% full. If the information above is not followed exactly, a fire causing

death or serious injury may occur.

• The LPG cylinder must be turned OFF when the appliance is not in use.

• LPG cylinders must be stored outdoors and out of the reach of children.

• DO NOT store an LPG cylinder inside a building, garage, or any other enclosed area.

LEAK TEST: LPG CYLINDER

STEP 01

Use a clean paintbrush

figure 01

to brush a  mild soap and water solution onto joint areas of the LPG cylinder.

(Indicated by arrows in figure 01.)

• Leaks are indicated by growing bubbles.



WARNING

If growing bubbles appear during leak test, DO NOT use or move the LPG cylinder.

Immediately contact an LPG supplier or fire department.

FITTINGS & HOSES

• Annual checking and tightening of metal fittings is recommended.

• Keep the fuel supply hose away from any heated surfaces.

• Before each use, check to see if hoses are cut or worn.

• Replace damaged hose before using appliance.

(Use only Blackstone approved valve, hose, or regulator. Failure to comply will void the warranty.)



BLACKSTONEPRODUCTS.COM/SUPPORT

MODELS:   

| OWNER’S MANUALUSING YOUR BLACKSTONE

ENGLISH

REGULATOR SAFETY

• Use this appliance, as purchased, only with gas and regulator/ valve assembly supplied. DO NOT use quick connect fittings or other add-ons.

• DO NOT cross thread (force at an improper angle) the connection between your LPG cylinder and regulator.

• If you can not connect the regulator, DO NOT use the regulator.

Regulator must be replaced with a Blackstone approved model by a professionally licensed, authorized dealer.

CONNECT THE LPG CYLINDER

ONLY USE A 20 LB (9 KG) CYLINDER

STEP 01

knobs to OFF.

❶

is OFF by turning the OPD hand wheel clockwise to a full stop.

❷

the Type 1 valve outlet.

STEP 02

straight line with the Type 1 valve outlet so as not to cross thread the connection.

Center and insert the regulator nipple into the Type 1 valve outlet.

Hand-tighten the coupling nut in a clockwise direction. (DO NOT use tools to connect.)

If connection cannot be completed, disconnect regulator and repeat this step.

STEP 03

to the appliance by hanging it on the LPG hook so that it nestles against the LPG support.

The safety relief valve must face away from the user while the appliance is in use.

Turn the control

Ensure that the LPG cylinder

❷

Remove the safety cap from

Hold the regulator in a

Secure the LPG cylinder

LEAK TEST: VALVES, HOSE & REGULATOR

STEP 01

STEP 02

STEP 03

Turn the control knobs to OFF. Connect the regulator to the LPG cylinder. Completely open the LPG tank by turning the OPD hand

wheel counterclockwise.

• If you hear a rushing sound, turn gas o immediately. There is a major leak at the connection.

• Immediately close the LPG cylinder by turning the OPD hand wheel clockwise and re-tighten connections. If leaks cannot be stopped DO NOT TRY TO REPAIR.

STEP 04

to brush a  mild soap and

Use a clean paintbrush

figure 02

water solutionn onto joint areas of valves and regulator.

(Indicated by arrows in figure 02.)

• Leaks are indicated by growing bubbles.

• Immediately close the LPG cylinder by turning the OPD hand wheel clockwise and re-tighten connections.

 WARNING

If leaks cannot be stopped, DO NOT try to repair. Regulator must be replaced with a Blackstone approved

model by a professionally licensed, authorized dealer.

DISCONNECTING THE LPG CYLINDER

STEP 01

❶

is OFF by turning the OPD hand wheel clockwise to a full stop.

❷

er-clockwise by hand to remove the regulator. (DO NOT use tools to disconnect.)

STEP 02

cylinder valve outlet whenever cylinder is not in use.

Only install the type of dust cap on cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.

Ensure that the control knobs are turned to OFF.

Ensure that the LPG cylinder

Turn the coupling nut count-

Place dust cap on LPG

❷

BLACKSTONEPRODUCTS.COM/SUPPORT



OWNER’S MANUAL | USING YOUR BLACKSTONE

ENGLISH

IGNITION INSTRUCTIONS

MODELS:   

1. CHECK VALVES

STEP 01

STEP 02

If knobs

STEP 03

turn smoothly.

Turn knob to OFF position. Push in knob and release. Knob should spring back.

DO NOT

spring back, replace valve assembly before using appliance.

Rotate knob to LOW then turn back to OFF. Knob should



WARNING

If burner does not ignite with open gas supply valve, gas will continue to flow out of burner and could accidentally/ inadvertently ignite with risk of injury.

Ensure gas is o at the supply shut o valve before checking appliance valves.

2. BATTERY POwERED IGNITION



DO NOT lean over the appliance while lighting.

STEP 01

battery (not included) under the ignitor button.

Screw the button into place over the positive terminal.

STEP 02

❶

Turn gas ON by turning the gas cylinder handwheel counterclockwise 1 to 3 turns.

STEP 03

❷ ❸

(Release the ignitor button when the burner lights.)

❹

Insert one (1) AA

Turn the control knob to OFF.

Push and hold the ignitor button. Push and turn the control knob counter-clockwise to HIGH.

Adjust the temperature to desired level.

❶

❷

3. ALwAYS CHECK BURNER FLAME BEFORE USE.

STEP 01

STEP 02

is at HIGH, flames should be larger than when knob is at LOW.

HEALTHY FLAME PATTERN YELLOw OR IRREGULAR

❶ ❷ ❸

Light burners and rotate knobs from HIGH to LOW. Look below the cooking surface to view burners. When knob

❶

❷

❸

Flickers of yellow color. Dark blue color. Vibrant blue.

If there is a sudden drop or low flame issue, please reference the Troubleshooting chapter.

❸

❹

IF IGNITION DOES NOT OCCUR IN 5 SECONDS:

STEP 01

STEP 02

STEP 03

If burner does not ignite, please reference the Troubleshooting chapter.

Turn the burner control knob OFF. Wait 5 minutes. Repeat the lighting procedure.



BLACKSTONEPRODUCTS.COM/SUPPORT

• Too much oil was used.

STEP 01

Turn your griddle on high

and let it heat for 10-15 minutes.

STEP 02

of the thickened and partially cooked oil as you can.

STEP 03

thin layer of oil.

MODELS:   

GRIDDLE SEASONING INSTRUCTIONS

wASHING YOUR GRIDDLE TOP BEFORE FIRST USE

NOTICE

Soap will ruin a seasoned griddle. This is the only time you should use soap on the griddle cooking surface.

STEP 01

cooking surface with hot, soapy water.

STEP 02

completely.

Wash the griddle

Rinse and dry

| OWNER’S MANUALUSING YOUR BLACKSTONE

wHAT OIL IS BEST TO USE?

• Blackstone Seasoning and Cast Iron Conditioner.

• Any plant-based cooking oil.

• Rendered animal fat with no additives.

 CAUTION

Properly dispose of the rags/towels used to spread oil on your griddle top for seasoning purposes to prevent fires that might occur due to spontaneous combustion.

Under the right conditions, residual oil on rags or towels can oxidize long after being removed from a heat source. The oxidation process itself produces heat which, if not dissipated, can build up and cause combustible materials (including the rags/towels themselves) to ignite.

ENGLISH

SEASONING YOUR GRIDDLE

VIDEO TUTORIAL

How to Season a New Blackstone Griddle

 youtube.com/watch?v=VspmDVnj2pI&t=3s

STEP 01

griddle top.

STEP 02

high heat until your griddle top changes color. (~10 min)

STEP 03

paper towel or cotton cloth and spread 2-3 tablespoons of your seasoning oil across the entire griddle top.

When seasoning your griddle top, remember to use a thin and even layer of oil—the thinner the layer of oil, the easier it will be to burn it o.

STEP 04

for another layer of oil when it stops smoking. Repeat STEP 03 3-4 times, or until the griddle surface is black.

BLACKSTONEPRODUCTS.COM/SUPPORT

Wipe any debris o

Set your griddle to

Use tongs to hold a

The griddle top is ready

SEASONING TROUBLESHOOTING

THERE IS A BROwNISH RESIDUE ON THE GRIDDLE SURFACE:

POSSIBLE CAUSES SOLUTION

• You turned o the heat too soon.

Scrape o as much

Re-season with a very

THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:

After using your griddle for multiple cooks, the seasoning will even out and improve.

PREVENTING RUST

Use your griddle frequently. Every time you cook, you are adding to the seasoning, which makes rust less likely.

NOTICE

If you live in a humid or coastal climate, your griddle may require more frequent seasonings between uses.

If rust appears on the griddle surface, rub it o with steel wool, low grit sandpaper or the Blackstone Pumice Stone and re-season the surface.

VIDEO TUTORIAL

Recovering your Blackstone Griddle Top

 youtube.com/watch?v=thPE2IgnSiI



OWNER’S MANUAL | USING YOUR BLACKSTONE

ENGLISH

USING YOUR AIR FRYER

LPG AIR FRYER IGNITION

STEP 01

STEP 02

battery (not included) under the ignitor button.

Screw the button into place over the positive terminal.

STEP 03

❶

knob to OFF.

STEP 04

the gas cylinder handwheel counterclockwise 1 to 3 turns.

Plug power cord into wall outlet.

Insert one (1) AA

Turn the fryer control

Turn gas ON by turning

MODELS:   

AIR FRYER SAFETY

• Remove items below the air fryer before operating.

• Blow out drawers before cooking to keep passageways clean.

• Wrap the power cord around the power cord bracket when the air fryer is not in use.

wHILE IN USE

• DO NOT restrict the flow of the combustion air or the hot exhaust gasses.

• DO NOT place fryer drawers on griddle surface.

• DO NOT place fryer drawers on or near a hot gas or electric burner, or in a heated oven.

FOOD

• DO NOT cook food in the fryer without the drawer in place.

• DO NOT add liquids (water or sauces) to hot food in the drawer as it may flash to steam and cause burns.

COOKING SPRAY

Cooking spray will degrade the non-stick coating. We recommend using regular cooking oil in a spray bottle.

STEP 05

❷

Push and hold the

❷

ignitor button.

Push and turn the fryer

❸

control knob counter-clockwise to MAX. (Release the ignitor button when

❶

the burner lights.)

Adjust the temperature to

❹

desired level.

❸

❹

To verify that the air fryer burner has lit, look into the burner chamber from the side of the unit.

STEP 06

Push the rocker switch to power ON, the blower fan will start immediately.

MATCH LIGHTING INSTRUCTIONS

If you can not ignite the air fryer with the control knob:

STEP 01 STEP 02

Turn control knob to OFF position.

Pinch a match into the match lighter stick. Light the match.

STEP 03

Guide the flame into the burner hole until it touches the burner.

CLEANING YOUR AIR FRYER

• DO NOT clean with alcohol or any other flammable substance.

• DO NOT clean the air fryer unit with a water spray or the like.

CLEANING YOUR AIR FRYER BASKET

Your air fryer basket is dishwasher safe, but the handle assembly is not.

(Basket design may vary depending on appliance.)

STEP 01

STEP 02

thumb screws.)

STEP 03

STEP 04

Reassemble the drawer after the basket is clean and dry.

Loosen the upper thumb screws in the air fryer drawer. Lift and remove the handle assembly. (DO NOT remove the

Remove the trivet from the air fryer basket. Keep the handle assembly with your appliance.

STEP 04

Push in and turn the control knob to start gas flowing. Ensure burner lights and stays lit.



BLACKSTONEPRODUCTS.COM/SUPPORT

CLEANING YOUR AIR FRYER

• DO NOT clean with alcohol or any other flammable substance.

• DO NOT clean the air fryer unit with a water spray or the like.

CLEANING YOUR AIR FRYER BASKET

Your air fryer basket is dishwasher safe, but the handle assembly is not.

STEP 01

Loosen the upper thumb screws in the air fryer drawer.

STEP 02

Lift and remove the handle assembly. (DO NOT remove the

thumb screws.)

STEP 03

Remove the trivet from the air fryer basket.

STEP 04

Keep the handle assembly with your appliance.

Reassemble the drawer after the basket is clean and dry.

AIR FRYER SAFETY

• Remove items below the air fryer before operating.

• Blow out drawers before cooking to keep passageways clean.

• Wrap the power cord around the power cord bracket when the air fryer is not in use.

wHILE IN USE

• DO NOT restrict the flow of the combustion air or the hot exhaust gasses.

• DO NOT place fryer drawers on griddle surface.

• DO NOT place fryer drawers on or near a hot gas or electric burner, or in a heated oven.

FOOD

• DO NOT cook food in the fryer without the drawer in place.

• DO NOT add liquids (water or sauces) to hot food in the drawer as it may flash to steam and cause burns.

COOKING SPRAY

Cooking spray will degrade the non-stick coating. We recommend using regular cooking oil in a spray bottle.

HOw TO USE YOUR PIzzA OVEN

FRESH PIzzA

STEP 01

Preheat your oven on high for about 20-25 minutes.

STEP 02

Once the desired stone temperature is reached (650°-750°F (340°- 400°C) for fresh dough pizza), turn the control knob to low. Depending on what you are cooking, you may adjust the temperature while cooking to achieve desired results.

Note: The thermometer only measures the air temperature in the oven, NOT the stone temperature. Use an infrared thermometer (not included) to measure the bottom stone temperature. Proper stone

temperature is critical for consistent results.

STEP 03

Pizza cooking time is about 2-4 minutes depending on the size and thickness of the pizza.

• Thinner foods should be cooked at a higher temperature for a

shorter time.

• Thicker or denser foods should be cooked at a lower temperature

for a longer time.

STEP 04

Pull the pizza out when the crust has reached your desired readiness, or when the edges of the pizza crust are golden-brown.

FOR BEST RESULTS:

• Wait to put a new pizza in until the temperature of the bottom stone

is back to your desired temperature.

• Set the temperature to HIGH between cooks and LOW during cooks.

• Keep the door closed as much as possible to retain heat.

• Experiment with pieces of dough beforehand to determine the

optimal stone temperature for your pizza.

FROzEN PIzzAS, COOKIES, ETC.

Follow the food manufacturer’s directions. Let frozen food thaw a little before putting it into the hot oven. This will prevent your pizza stone from cracking.

CLEANING YOUR OVEN INTERIOR

STEP 01

Apply a strong solution of detergent and water, or use an oven cleaner with scrub brush on insides of oven lid and floor. Rinse and allow to completely air dry.

STEP 02

Reference the Troubleshooting chapter for instructions on cleaning the burner.

MODELS:   

COOKING ON YOUR BLACKSTONE

 CAUTION

This appliance will be hot during and after use. Use longhandled utensils and oven mitts/ protective gloves when handling potentially hot parts to protect against burns and splatters.

 CAUTION

If the appliance is fitted with a paper towel holder, the arm must be in the open position while the appliance is in use.

NOTICE

DO NOT store any items within 3 in (8 cm) of the cooking surface while in use.

IF GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR REGULATOR:

STEP 01

STEP 02

STEP 03

STEP 04

Instructions)

VIDEO RECIPES

Find recipes and cooking tips at:



 youtube.com/BlackstoneGriddles    @blackstoneproducts

Turn o gas supply immediately. Determine the cause and correct it. Clean and inspect valve, hose and regulator. Perform a leak test. (Please reference the Leak Test

BlackstoneProducts.com/recipes

STRAwBERRIES AND CREAM PANCAKES

Breakfast

| OWNER’S MANUALUSING YOUR BLACKSTONE

BLACKBERRY SCONES

Air fryer

ENGLISH

OKLAHOMA FRIED ONION BURGER

Lunch

BLACKSTONEPRODUCTS.COM/SUPPORT

TACOS BORRACHOS

Dinner

THYME CHICKEN wINGS

Air fryer

JALEPEÑO POPPERS

Air fryer



OWNER’S MANUAL | USING YOUR BLACKSTONE

HOw TO USE YOUR PIzzA OVEN

FRESH PIzzA

STEP 01

Preheat your oven on high for about 12-15 minutes.

STEP 02

Once the desired stone temperature is reached (650°-750°F (340°- 400°C) for fresh dough pizza), turn the control knob to low. Depending on what you are cooking, you may adjust the temperature while cooking to achieve desired results.

Note: The thermometer only measures the air temperature in the oven, NOT the stone temperature. Use an infrared thermometer (not included) to measure the bottom stone temperature. Proper stone

temperature is critical for consistent results.

STEP 03

Pizza cooking time is about 2-4 minutes depending on the size and thickness of the pizza.

• Thinner foods should be cooked at a higher temperature for a

shorter time.

• Thicker or denser foods should be cooked at a lower temperature

for a longer time.

STEP 04

Pull the pizza out when the crust has reached your desired readiness, or when the edges of the pizza crust are golden-brown.

FROzEN PIzzAS, COOKIES, ETC.

Follow the food manufacturer’s directions. Let frozen food thaw a little before putting it into the hot oven. This will prevent your pizza stone from cracking.

CLEANING YOUR OVEN INTERIOR

If the pizza falls o the rotating stone and catches on fire:

STEP 01

Turn OFF the control knob, turn OFF the LPG cylinder, turn OFF the rotating motor.

STEP 02

Allow the oven to completely cool.

STEP 03

Remove the oven lid, the top stone, and the lower stone.

STEP 05

Use a spatula to scrape and remove debris from cooking cavity floor. Wipe cooking cavity with a damp cloth. DO NOT use detergent.

STEP 06

Use a vacuum if necessary to clean out food debris inside cooking chamber.

STEP 04

Remove the turntable by removing the two (2) bolts that attach the turntable to the rotating shaft.

CLEANING YOUR PIzzA STONE

STEP 01

Set your oven to HIGH for 15~20 min to burn o residue.

STEP 02

Once your oven has cooled completely, flip the stone over and use the cleaner side.

NOTICE

DO NOT use soap on the cooking stone. This will leave a soap taste in food.

ENGLISH

CLEANING YOUR GRIDDLE TOP

Clean griddle top after each use, while still warm.

• DO NOT use soap on the griddle top. This will destroy the griddle’s seasoning.

VIDEO TUTORIAL

How to Clean your Blackstone Griddle

 youtube.com/watch?v=-Iedu9z6NPY

STEP 01

into the grease cup with spatula or straight metal scraper.

STEP 02

with paper towel.

STEP 03

of water to the griddle surface, then scrape the water and debris into the grease cup.

(For stuck-on food residue, use a bit of coarse salt.)

Push loose food debris

Wipe down griddle top

Apply a few tablespoons

MODELS:   

CARE AND MAINTENANCE

 WARNING

Grease build up can cause a fire. Clean any part of the appliance that gets hot and experiences grease build up after each use.

 CAUTION

All cleaning and maintenance should be carried out when the appliance is cool and everything is turned OFF.

• DO NOT use abrasive pad on areas with graphics.

• If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to cooking.

APPLIANCE BODY:

Wash with warm soapy water and immediately wipe dry with a non-abrasive cloth. (DO NOT allow cleaning agents to rest on any porous surface for a prolonged amount of time.)

DO NOT use Citrisol, abrasive cleaners, or a concentrated cleaner on the appliance. This may result in damage to and

NOTICE

failure of parts.

STEP 04

Wipe again with a paper

towel and dry completely.

STEP 05

Apply thin coat of cooking oil to maintain seasoning and protect the griddle top.

EMPTY YOUR GREASE CUP

The grease cup must be removed and emptied after each use.



CAUTION

Grease cup will be hot during and after use. DO NOT remove the grease cup until the griddle has completely cooled.



APPLIANCE STORAGE

DO NOT move the appliance when in use. Allow the appliance to cool to 115°F (45°C) before moving or storing.

Storage of an appliance indoors is only permissible if the gas supply is disconnected and removed from the appliance.

COVER FIT GUIDE

Always cover your appliance when stored outdoors.

To find a cover that will fit your appliance, visit BlackstoneProducts.com/support.

 WARNING

BLACKSTONEPRODUCTS.COM/SUPPORT

Obstructions in the burner, gas

Clean the burner, jets, and gas

Gas cylinder is empty or low.

Refill or replace the gas

The regulator’s flow limiting

Reset the safety system:

STEP 01

close the LPG cylinder valve, and disconnect the regulator from the LPG cylinder.

STEP 02

allow the pressure to dissipate, then reconnect the regulator to the LPG cylinder and slowly open the OPD hand wheel one half turn.

STEP 03

Ignitor wire misaligned.

Ensure that the ignitor needle

the burner, and aligned with the

Damage to the ignition system.

Contact customer support for

Burner tubes are not receiving

Clean the burner assembly to

Dead / improperly installed

Replace with new battery.

MODELS:   

TROUBLESHOOTING

| OWNER’S MANUALTROUBLESHOOTING

ENGLISH

IGNITION TROUBLESHOOTING

BURNER wILL NOT IGNITE:

If ignition does not occur in 5 seconds:

STEP 01

STEP 02

STEP 03

If this does not work, to determine the cause, please try to ignite your appliance with a match.

MATCH LIGHTING INSTRUCTIONS

Before beginning, check for gas leaks. Open hood (if applicable).

STEP 01

STEP 02

lighter) no shorter than 11 inches long.

STEP 03

the burner.

STEP 04

Ensure burner lights and stays lit.

IF YOU CAN IGNITE YOUR APPLIANCE wITH A MATCH:

Turn the burner control knob OFF. Wait 5 minutes. Repeat the lighting procedure.

Turn control knob to OFF position. Light a match (or long

Place the flame next to

Push in and turn the control knob to start gas flowing.

POSSIBLE CAUSES SOLUTION

GAS FLOw TROUBLESHOOTING

BURNER FLAMES ARE YELLOw OR IRREGULAR:

• Appliance will not achieve a high heat or heats unevenly.

• Burner flames start strong, then immediately drop to low even when burner is set to high position.

• Flame height drops when a second burner is lit.

• Flames DO NOT extend the full length of the burner, or only run on one side of the burner.

• Burner flames are inconsistent.

POSSIBLE CAUSES SOLUTION

jets, or fuel rail.

device was triggered.

hose.

cylinder.

Turn OFF the appliance,

Wait five minutes to

battery.

IF YOU CAN NOT IGNITE YOUR APPLIANCE wITH A MATCH:

POSSIBLE CAUSES SOLUTION

fuel.

BLACKSTONEPRODUCTS.COM/SUPPORT

is positioned 3-7mm away from

burner holes.

3-7mm

replacement parts.

remove the obstruction.

Regulator stuck in safety position.

A FLAME IS COMING OUT OF THE AIR GATE:

POSSIBLE CAUSES SOLUTION

Something is blocking the venturi in the burner.

Contact customer support for replacement parts.

Clean the burner assembly to remove the obstruction.

Ignite your appliance.



OWNER’S MANUAL | TROUBLESHOOTING

ENGLISH

CLEANING THE BURNER ASSEMBLY

To reduce chance of “flash-back” the procedure below should be followed at least once a month when spiders are most active or when your appliance has not been used for a period of time.

VIDEO TUTORIAL

How to Clean Your Burner Tube

 youtube.com/watch?v=xKQTCrFCzf8

MODELS:   

CUSTOMER SUPPORT

Visit us online at BlackstoneProducts.com/support for assistance concerning appliance use, replacement parts, or your warranty.

CUSTOMER SUPPORT HOURS:

Monday – Friday



7:00 am – 5:00 pm (Mountain Time)

STEP 01

Ensure that the gas is turned OFF at control knobs and gas

supply. Remove the griddle top.

STEP 02

Carefully detach and

remove the burner.

STEP 03

Clean the inside of

the burner: a. Run a bottle brush (not a wire

brush) or a sti wire bent into a small hook through each burner tube several times.

b. Use compressed air to blow

through the burner tube and out the burner ports (Wear eye protection).

STEP 04

Brush entire outer surface of burner to remove grime.

STEP 05

Clean any blocked ports with sti wire such as an open paper clip.

STEP 06

Carefully replace burners and reattach, with attention to the location of the ignition needle.



Fuel nozzle

Burner opening



The gas rail fuel nozzle must be reengaged within the burner opening.

BLACKSTONEPRODUCTS.COM/SUPPORT

��

MODELS:   

wARRANTY

The North Atlantic Imports LLC 1-Year Warranty covers replacement parts up to one year after the date of purchase.

TO ENABLE THIS wARRANTY, YOU wILL NEED TO PROVIDE:

Your appliance’s Serial Number

☞

FREE

��

☞

��

The Serial Number can be found on your appliance’s Manufacturer Label.

(The Manufacturer Label is a large silver sticker found on the body of your appliance.)

wARRANTY OVERVIEw

North Atlantic Imports, the manufacturer, will warranty for one year from purchase all parts, workmanship, and finishes. It will be the manufacturer’s option as to whether to repair or replace any of the above items. All warranties are limited to the original purchaser only. This warranty does not cover any liability on the part of North Atlantic Imports, its agents or employees, for any indirect or consequential damages for breach of warranty. The purchaser must follow the manufacturer’s usage instructions.

Under no circumstances is the manufacturer responsible for damages from the failure to operate the cooking station properly. It is the responsibility of the purchaser to establish the warranty period by verifying the original purchase date with original sales receipt.

��

Register your appliance at

BlackstoneProducts.com/register

MOBILEFRIENDLY

COOKBOOK

when you register

��



��

| OWNER’S MANUALWARRANTY

DETAILED ExPLANATION OF THE wARRANTY

North Atlantic Imports LLC warrants to the owner that the product covered by this agreement is free from defects in material and workmanship under normal use and service for which it was intended if, but only if, it has been operated in accordance with North Atlantic Imports LLC instructions exclusively for domestic use, and not for private or public club, institutional or commercial purposes.

North Atlantic Imports LLC’s obligation under this warranty is limited to replacing or repairing, free of charge, any part or parts that may prove, to the satisfaction of North Atlantic Imports LLC, to be defective under normal home use and service within the following stated periods of time from the date of purchase; for one year from purchase, all parts, finish, and workmanship. Should any failure to conform to this warranty become apparent during applicable warranty periods stated above, the original purchaser must notify North Atlantic Imports LLC of breach of warranty within the applicable warranty period.

North Atlantic Imports LLC shall upon notice and compliance by the original purchaser with such instructions, correct such nonconformity by repair or replacement of the defective part or parts.

Correction in the manner provided above shall constitute a fulfillment of all obligations of North Atlantic Imports LLC with respect to the quality of the product.

North Atlantic Imports LLC does not warrant this equipment to meet the requirement of any safety code of any state, municipality or other jurisdiction, and the original purchaser assumes all risk and liability whatsoever resulting from the use thereof, whether used in accordance with North Atlantic Imports LLC instructions or otherwise.

This warranty does not cover and is intended to exclude any liability on the part of North Atlantic its agents, servants or employees whether under this warranty or implied by law for any indirect or consequential damages for breach on any warranty. The purchaser must establish all applicable warranty periods pursuant to this warranty by verifying the original purchase date by producing the dated sales receipt. This warranty shall not apply to this product or any other part thereof which has been subject to accident, negligence, alteration, abuse, or misuse or which has been repaired or altered without North Atlantic written consent, outside of North Atlantic Imports LLC factory. The full manufacturer warranty is not valid for griddles purchased from unlicensed, third-party resellers, purchased at a discount due to missing or damaged parts, or purchased as a floor model; at the discretion of North Atlantic Imports.

North Atlantic Imports LLC makes no warranty whatsoever in respect to accessories or parts not supplied with it. This warranty shall apply only within the boundaries of the United States of America and Canada. This warranty gives the original purchaser specific rights, and the original purchaser may also have other rights, which vary from state to state.

ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT



ENGLISH

OWNER’S MANUAL |

MODELS:   

This page intentionally left blank



BLACKSTONEPRODUCTS.COM/SUPPORT

MODELS:   

| OWNER’S MANUAL

ENGLISH

This page intentionally left blank

BLACKSTONEPRODUCTS.COM/SUPPORT



ENGLISH

This product may be covered by one or more issued U.S. and/or

international patents and may include patent applications pending.

For more information, please visit: BlackstoneProducts.com/patents

DISTRIBUTED BY NORTH ATLANTIC IMPORTS, LLC  W  N LOGAN, UT  USA | BLACKSTONE IS A REGISTERED TRADEMARK OF NORTH ATLANTIC IMPORTS, LLC



BLACKSTONEPRODUCTS.COM/SUPPORT