Blackstar ARTISAN A30 Owner's Manual

Owner’s Manual

HAND-CRAFTED TONE

Designed and Engineered by

Blackstar Amplification UK

3

USA / Canada

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods
of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.

“TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC MAINS,
DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC
RECEPTACLE”.

“WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE AND OBJECTS FILLED
WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS

APPARATUS”.

This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock
to persons.

This symbol is intended to alert the user to the presence of important
operation and maintenance (servicing) instructions in the literature
accompanying the appliance.

If the product does not operate normally, when the operating instructions are
followed, then refer the product to a qualified service engineer.

The U.S. Government´s Occupational Safety and Health Administration (OSHA) has
specified the following permissible noise level exposures:

Duration Per Day In Hours Sound Level dBA, Slow Response
8 90
6 92
4 95
3 97
2 100
1½ 102
1 105
½ 110
¼ or less 115

According to OSHA, any exposure in excess of the above permissible limits could
result in some hearing loss.

Ear plug protectors in the ear canals or over the ears must be worn when operating
this amplification system in order to prevent a permanent hearing loss if exposure is
in excess of the limits as set forth above. To ensure against potentially dangerous
exposure to high sound pressure levels, it is recommended that all persons exposed
to equipment capable of producing high sound pressure levels such as this
amplification system be protected by hearing protectors while this unit is in operation.

English

5

Warning!

Important safety information!

READ THE FOLLOWING INFORMATION CAREFULLY. SAVE ALL
INSTRUCTIONS FOR FUTURE REFERENCE!

Follow all warnings and instructions marked on the product!

Danger! High internal operating voltages

Do not open the equipment case. There are no user serviceable parts in this
equipment. Refer all servicing to qualified service personnel.

Clean only with a dry cloth.

Condensation can form on the inside of an amplifier if it is moved from a cold
environment to a warmer location. Before switching the unit on, it is recommended
that that the unit me allowed to reach room temperature.

Unauthorised modification of this equipment is expressly forbidden by Blackstar
Amplification Ltd.

Never push objects of any kind into ventilation slots on the equipment casing.

Do not expose this apparatus to rain, liquids or moisture of any type.

Follow all warnings and instructions marked on the product!

Do not place this product on an unstable trolley, stand or table. The product may fall,
causing serious damage to the product or to persons!

Do not cover or block ventilation slots or openings.

This product should not be placed near a source of heat such as a stove, radiator,
or another heat producing amplifier.

Use only the supplied power cord which is compatible with the mains voltage supply
in your area.

Power supply cords should always be handled carefully and should be replaced if
damaged in any way.

Never break off the earth (ground) pin on the power supply cord.

The power supply cord should be unplugged when the unit is to be unused for long
periods of time.

Before the unit is switched on, the loudspeaker should be connected as described
in the handbook using the lead recommended by the manufacturer.

Always replace damaged fuses with the correct rating and type.

Never disconnect the protective mains earth connection.

High loudspeaker levels can cause permanent hearing damage. You should therefore
avoid the direct vicinity of loudspeakers operating at high levels. Wear hearing
protection if continuously exposed to high levels.

English

4

All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.

Technical Information

Power Amplifier

The Artisan 30 power amplifier uses four EL84 power pentode valves in Class A.
The EL84s used are graded in terms of quiescent operating point and
transconductance giving excellent hum performance and dynamic feel.

The Artisan 30 power amplifier operates in two modes, namely pentode (30W) or
triode (10W), depending on the setting of the Power Amplifier Mode control.

In pentode mode the power amplifier has a dynamic response which is rich in bell
like harmonics and has a beautiful ringing top end. The triode mode allows the
generation of the critical power amplifier harmonic distortion at a much lower volume
but is darker and more mellow sounding with a rounder top end. The lower power
setting is particularly effective for home and studio use.

The power amplifier is further enhanced by using a cathode coupled phase splitter
to provide the best possible balance in the power amplifier drive and hence superb
dynamic response. In keeping with the vintage sonic signature of the Artisan 30, the
use of a valve rectifier adds compression to the power amplifier response and is
critical in generating its feel and responsiveness. The GZ34 valve rectifier used in the
Artisan 30 is also found in other classic designs.

With an amplifier that is built to last reliability of the electronic circuitry is essential and
therefore all the other power amplifier and power supply components are also over­specified for the best possible reliability.

Preamplier

Channel 1 – The EF86 Channel

Hi/Lo inputs provide perfect matching either directly to the guitar (high sensitivity) or
for connection to higher output effects pedals (low sensitivity).

This channel is based on the EF86 preamplifier pentode valve. Originally, this valve
was most commonly used in high-end audio applications due to its high gain, low
noise characteristics. However, in very early American guitar amplifier designs a
pentode was used in the preamplifier circuit. The use of a pentode in these early
designs provided unique gain and compression characteristics which make these
amplifiers so revered for studio use today.

In keeping with the reference American designs, the extra gain of the EF86 of the
Artisan 30 allows the power amplifier to be driven harder for more compression and
rich harmonic distortion. The EF86 also adds its own particular compression and
distortion flavour to this channel making Channel 1 a dream to record with.

The 5-position Bass Shape switch controls the bass drive into the power amplifier
and enables the user to quickly and easily select from a wide palette of tonal options
from bright and glassy through to fat and smooth.

The tone control circuit is unusual in its position across the anode of the EF86. This
retro type of design offers a complex response that works in harmony with the
dynamics of the player’s attack.

English

7

Introduction

Thank you for purchasing this Blackstar Artisan 30 handwired combo.

The Artisan 30 is the result of countless hours of painstaking Research and
Development by our world class design team. Based in Northampton (UK), the
Blackstar team are all experienced musicians themselves and the sole aim of the
development process is to provide guitarists with products which are the ultimate
tools for self expression.

Realising the skills and expertise of over thirty years of valve guitar amplifier design
experience, the Artisan 30 represents a new level in handwired design, tone and
build quality.

All Blackstar products are subject to extensive laboratory and road testing to ensure
they are truly uncompromising in terms of reliability, quality and above all TONE!

If you like what you hear and want to find out more about the Blackstar range of
products please visit our website at www.blackstaramps.com.

Thanks!

The Blackstar Team

Features

The Artisan 30 is inspired by some of the most revered combos in guitar amplifier
history. The design is in the classic 30W / 2x12 combo format and is very simple to
use and yet highly flexible in functionality and tone.

The Artisan Series of handwired amplifiers represents the absolute highest standard
of craftsmanship and boutique tone. With the emphasis on simplicity and sonic
purity, every feature has been refined to provide the artist with the widest range of
reference vintage tones. This is achieved by the design of electronic circuits that
work in harmony with the finest components and materials available.

The Artisan 30 is built to last a lifetime and effortlessly combines vintage style and
rugged, road tested reliability. The point-to-point tag board construction, welded
steel chassis and finger-jointed birch-ply cabinet are complemented by beautiful
vintage red Tolex and etched aluminium panels.

English

6

Front Panel

Channel 1

1. Hi Input

This is the high sensitivity input of Channel 1. This input has 6dB more (i.e. twice as
much) gain as the Lo Input. Use this input if you wish to achieve power amplifier
break-up and overdrive. Always use a high quality screened guitar lead.

2. Lo Input

This is the low sensitivity input of Channel 1. This input has 6dB less (i.e. half as
much) gain as the Hi Input. Use this input if you wish the power amplifier to remain
clean (this is especially useful if the guitar used has high output pick-ups). Always use
a high quality screened guitar lead.

3. Volume

This controls the volume of Channel 1. Turning it clockwise increases the volume. The
EF86 used in Channel 1 provides higher levels of gain and distortion than the ECC83
in Channel 2 and its own unique compression characteristics. This channel will sing
with sustain and give you all the drive you need for classic bluesy lead tones.
Remember that you can use the Lo Input of Channel 1 to experiment with the clean
side of the EF86’s tonal character.

4. Tone

This passive control affects the tonal characteristics of Channel 1. Fully counter­clockwise the tone is thick and dark, turning it clockwise increases the amount of
treble and the tone becomes more shimmering and bright.

5. Bass Shape

This 5-position switch controls the bass drive into the power amplifier and enables
the user to quickly and easily select from a wide palette of tonal options, from bright
and glassy through to fat and smooth. In position 1 the tone is sharp with a tight,
funky bottom end. In position 2 the tone is firm with lower mids. In position 3 the tone
achieves a more even balance across the mid range and bass. In position 4 the tone
becomes richer and deeper. Position 5 offers the warmest, fullest tone of the five
positions.

Channel 2

6. Hi Input

This is the high sensitivity input of Channel 2. This input has 6dB more (i.e. twice as
much) gain as the Lo Input. Always use a high quality screened guitar lead. Use this
input if you wish to achieve power amplifier break-up and overdrive.

7. Lo Input

This is the low sensitivity input of Channel 2. This input has 6dB less (i.e. half as
much) gain as the Lo Input. Always use a high quality screened guitar lead. Use this
input if you wish the power amplifier to remain clean. This input is especially useful
if the guitar used has high output pick-ups.

English

9

The extra gain of the EF86 allows the power amplifier to be driven harder for more
compression and rich harmonic distortion. The EF86 also adds its own particular
compression and distortion flavour to this channel.

Channel 2 – The ECC83 Channel

Hi/Lo inputs provide perfect matching either directly to the guitar (high sensitivity) or
for connection to higher output effects pedals (low sensitivity).

This channel’s tone is most easily described as a blend between a boutique EL84
combo and classic British 100W head. The philosophy is to deliver the bell-like ring
and richness of a warm, retro combo with the added openness and roar of a vintage
high wattage head.

The flexibility of this channel is further enhanced by the addition of the 2-position
Voice switch which completely reconfigures the tone shaping network to give either
a ‘Warm’ or ‘Bright’ response.

Transformers

All Artisan transformers are traditionally made from the highest grade materials to
Blackstar’s demanding sonic and reliability specifications.

Output Transformers

The design of the output transformers is critical to ensuring highly responsive feel and
a full natural frequency response.

All the Artisan output transformers are constructed using laminations made of the
highest grade, grain oriented steel. This minimises core losses and ensures optimum
fidelity and dynamics.

Mains Transformer

The Artisan mains transformers are also constructed using laminations made of the
highest grade, grain oriented steel. This minimises stray magnetic fields which can
be a source of unwanted noise and hum.

English

8

In triode mode the tone is round and bluesy with a mellow top end for laid back
soloing. The triode mode also has the benefit of producing more saturated distortion
tones at lower output levels which makes this mode ideal for recording and practice.

The pentode mode produces a more dynamic feel and is louder and more punchy
than the triode mode. This setting is recommended for dynamic clean sounds and
pushier sounding crunch tones. This is a great setting for rehearsals and small club
gigs.

See the Modes of Operation Table below for the different configurations possible.

Modes of Operation Table

16. Standby

This switch applies the H.T. (High Tension) voltage required to produce sound.
Always turn this switch on at least 30 seconds after the Power switch (17) and off at
least 30 seconds before the Power switch. During short breaks in playing use just
this switch to turn ‘off’ and ‘on’ the amplifier’s output.

17. Power

This switch is used to turn the amplifier on and off. You should always turn this switch
on before turning on the Standby switch (16).

English

11

8. Gain

The Gain control adjusts the amount of Channel 2’s overdrive or distortion. Low
settings, counter clockwise, will deliver a clean sound on the edge of break-up. As
the Gain control is increased clockwise the sound will become more overdriven
moving through beautiful crunch tones.

9. Voice

The 2-position Voice switch completely reconfigures the interstage prevoicing
emphasis circuit to give either a ‘Warm’ or ‘Bright’ response.

10. Bass

This control affects the low frequencies. Turning it clockwise increases the amount
of bass present.

11. Middle

This control affects the mid range frequencies. Turning it clockwise increases the
amount of mid present.

12. Treble

This control affects the hig-end frequencies. Turning it clockwise increases the
amount of treble present.

13. Volume

This controls the volume of Channel 2. Turning it clockwise increases the volume. At
low volume levels the amplifier will produce exquisite, bell-like clean tones that are
definitively Class A in their character. As the volume is increased the tone becomes
fatter and more compressed as the power valves reach saturation. Further increases
in volume produce a wonderful tone as the power amplifier valves move into full
distortion. This type of valve power amplifier clipping produces the most natural guitar
distortion of all which reacts to every nuance of the guitarist’s playing style.

Master

14. Power Indicator Light

The power indicator will light when the amplifier is switched on.

15. Power Amplifier Mode Switch – 10 Watts / 30 Watts

This switch changes the power amplifier from triode mode (10 Watts) to pentode
mode (30 Watts).

English

10

Mode Preamplifier Power Amplifier Mode Setting Description
1 Channel 1 Triode EF86 / 10W
2 Channel 2 Triode ECC83 / 10W
3 Channel 1 Pentode EF86 / 30W
4 Channel 2 Pentode ECC83 / 30W
5 Channel 1 / Channel 2 Triode Blended 10W
6 Channel 1 / Channel 2 Pentode Blended 30W

1 2 10 11 15149 12 16133 4 5 6 7 8

17

Channel Blending

The Artisan 30’s topology allows the blending of the two channels. By paralleling the
guitar connection to the inputs of Channel 1 and Channel 2 (see Figure 1 and Figure
2 below) endless tonal variations can be explored.

Figure 1 Figure 2

Technical Specification

Power (RMS): 30 Watts or 10 Watts (Switchable)

Valves: 1 x GZ34, 4 x EL84, 3 x ECC83, 1 x EF86

Weight (kg): 35

Dimensions (mm): 715 x 569 x 263

English

13

Rear Panel

1. Speaker Outputs

There are two parallel speaker outputs for connecting the internal speakers and/or
an external speaker cabinet. When connecting speakers always ensure that the
Impedance Selector (2) is set correctly.

2. Impedance Selector

This control matches the amplifier’s impedance to that of the connected speakers.
Always ensure that the selected impedance matches that of the internal and/or
external speaker cabinets.

The Artisan 30’s internal speakers are 16 Ohms each. They are wired in parallel giving
a total impedance of 8 Ohms, so the impedance Selector must be set to 8 Ohms.
If an additional 8 Ohm speaker cabinet is used together with the internal speakers
the Impedance Selector should be set to 4 Ohms. A speaker cabinet of less than 8
Ohms should not be used together with the internal speakers.

WARNING: The amplifier must always be completely powered down before
adjusting the setting of the Impedance Selector. Failure to do this, or to correctly
match the impedance of the amplifier and speakers, will damage the amplifier.

3. H.T. Fuse

The value of the H.T. Fuse is specified on the rear panel. Never use a fuse of the
incorrect value or attempt to bypass it.

4. Mains Fuse

The value of the Mains Fuse is specified on the rear panel. Never use a fuse of the
incorrect value or attempt to bypass it.

5. Mains Input

The supplied detachable mains lead is connected here. The lead should only be
connected to a power outlet that is compatible with the voltage, power and
frequency requirements stated on the rear panel. If in doubt get advice from a
qualified technician.

English

12

12345

Hohe Lautsprecherpegel können permanente Hörschäden verursachen. Sie sollten
daher die direkte Nähe zu Lautsprechern, die auf hohen Pegeln betrieben werden,
vermeiden. Tragen Sie einen Hörschutz, wenn Sie kontinuierlich hohen Pegeln
ausgesetzt sind.

Wenn das Produkt nicht normal funktioniert, während die Betriebsanleitung befolgt
wird, übergeben Sie das Produkt an einen qualifizierten Servicetechniker.

Die Verwaltung zur Gesundheit und Sicherheit am Arbeitsplatz der US-Regierung
(OSHA) hat die folgenden zulässigen Lärmpegelbelastungen festgelegt:

Dauer pro Tag in Stunden Lärmpegel dBA, Langsame Reaktion
8 90
6 92
4 95
3 97
2 100
1½ 102
1 105
½ 110
¼ oder weniger 115

Laut der OSHA kann jede Belastung oberhalb der oben genannten zulässigen
Grenzwerte zu gewissen Hörverlusten führen.

Wenn dieses Verstärkersystem betrieben wird, müssen Ohrschützer im Ohrkanal
oder über den Ohren getragen werden, um permanenten Hörverlust zu vermeiden,
wenn die Belastung oberhalb der oben festgelegten Grenzwerte liegt. Um sich gegen
potenziell gefährliche Belastungen durch hohe Schalldruckpegel zu schützen, wird
empfohlen, dass alle Personen, die Geräten wie diesem Verstärkersystem ausgesetzt
sind, die in der Lage sind, hohe Schalldruckpegel zu entwickeln, während des
Betriebs dieses Geräts durch Ohrschützer geschützt werden.

15

Deutsch

Wichtige Informationen zur Sicherheit!

LESEN SIE DIE FOLGENDEN INFORMATIONEN SORGFÄLTIG DURCH.
BEWAHREN SIE ALLE ANLEITUNGEN FÜR DIE ZUKÜNFTIGE
BEZUGNAHME AUF

Befolgen Sie alle auf dem Produkt ausgewiesenen Warnungen und
Anleitungen!

Gefahr! Hohe interne Betriebsspannungen

Öffnen Sie nicht das Gehäuse des Geräts. Es befinden sich keine vom Anwender zu
wartende Teile in diesem Gerät. Überlassen Sie alle Servicearbeiten qualifiziertem
Wartungspersonal.

Nur mit einem trockenen Lappen reinigen

Auf der Innenseite eines Verstärkers kann sich Kondensationsnässe bilden, wenn er
von einer kalten Umgebung an einen wärmeren Ort bewegt wird. Es wird empfohlen,
dass das Gerät vor dem Einschalten Zimmertemperatur erreicht.

Unerlaubte Änderungen an diesem Gerät sind ausdrücklich von Blackstar
Amplification Ltd verboten.

Stecken Sie niemals Objekte jeglicher Art in die Lüftungsschlitze des Gehäuses.

Setzen Sie dieses Gerät nicht Regen, Flüssigkeiten oder Feuchtigkeit jeglicher Art
aus.

Befolgen Sie alle auf dem Produkt ausgewiesenen Warnungen und Anleitungen!

Platzieren Sie dieses Produkt nicht auf einem instabilen Rollwagen, Ständer oder
Tisch. Das Produkt kann herunterfallen und dem Produkt oder Personen ernsthaften
Schaden zufügen!

Blockieren oder verdecken Sie nicht die Lüftungsschlitze oder -öffnungen.

Dieses Produkt sollte nicht in der Nähe einer Wärmequelle wie einem Ofen,
Heizkörper oder einem anderen Hitze entwickelnden Verstärker platziert werden.

Verwenden Sie nur das zum Lieferumfang gehörende Netzkabel, das mit der
Netzstromversorgung in Ihrer Region kompatibel ist.

Netzkabel müssen stets mit Vorsicht gehandhabt und ersetzt werden, wenn sie in
irgendeiner Weise beschädigt werden.

Brechen Sie niemals den Erdungsstift (Erde) am Netzkabel ab.

Das Netzkabel sollte aus der Steckdose gezogen werden, wenn das Gerät längere
Zeit nicht verwendet wird.

Bevor das Gerät eingeschaltet wird, muss der Lautsprecher entsprechend der
Beschreibung im Handbuch unter Verwendung des vom Hersteller empfohlenen
Kabels angeschlossen werden.

Ersetzen Sie beschädigte Sicherungen stets mit der korrekten Spannung und Art.

Trennen Sie niemals die schützende Netz/Erde-Verbindung.

14

Deutsch

Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom Hausmüll über dafür
staatlich vorgesehenen Stelen entsorgt werden.

Technische Informationen

Endstufe

Die Endstufe des Artisan 30 nutzt vier EL84 Pentodenröhren in Class A-Technik.
Ruhestrom-Arbeitspunkt und Steilheit der verwendeten EL84-Röhren sind optimal
auf Brummreduzierung und hervorragende Dynamik abgestimmt.

Die Endstufe des Artisan 30 läuft in zwei Betriebsarten - Pentodenröhren (30 W) oder
triodenröhre (10 W), je nach Einstellung des Betriebsreglers der Endstufe.

Im Pentode Modus weist die Endstufe die Charakteristika eines britischen
Verstärkers der Klasse A der frühen 60-er Jahre auf, d.h. der Verstärker liefert einen
sehr dynamischen, glockigen Ton mit wunderbar krispen Höhen. Im Triode Modus
wird die Endstufenverzerrung bei viel geringerer Lautstärke erreicht, was den Sound
dunkler und wärmer macht. Die geringere Leistungsstufe eignet sich speziell für Heim
und Studio.

Die Endstufe verfügt zudem über einen kathodengekoppelten Phasensplitter und
gewährleistet so eine ausgezeichnete Symmetrie der Endstufenaussteuerung und
damit eine erstklassige Ansprechdynamik. Im Einklang mit den charakteristischen
klassischen Akustikmerkmalen des Artisan 30 sorgt der Einsatz eines
Röhrengleichrichters für eine verstärkte Kompression der Endstufenansprache und
ist entscheidend für die Erzielung eines guten Spielgefühls und einer hohen
Ansprechempfindlichkeit. Der hier verwendete GZ34 Röhrengleichrichter kommt
auch bei anderen klassischen Modellen zum Einsatz.

Bei einem auf lange Lebensdauer ausgelegten Amp muss die Elektronikschaltung
zuverlässig funktionieren. Daher sind all die anderen Endstufen- und
Netzteilkomponenten im Interesse optimaler Ausfallsicherheit ebenfalls
überdimensioniert.

Vorstufe

Kanal 1 – EF86-Kanal

Hi/Lo Eingänge bieten eine perfekte Abstimmung entweder direkt an der Gitarre
(hohe Empfindlichkeit) oder für den Anschluss von leistungsstärkeren Effektpedalen
(niedrige Empfindlichkeit).

Dieser Kanal basiert auf der EF86 Preamp-Pentodenröhre. Diese Röhre kam
ursprünglich aufgrund ihres hohen Gains und geringen Rauschens häufig in High­End-Audiogeräten zum Einsatz. In den ganz frühen amerikanischen Gitarrenamps
jedoch fand eine Pentode in der Vorstufen-Schaltung Verwendung. Eine solche
Pentode verlieh diesen Modellen besondere Gain- und Kompressionseigenschaften,
weshalb diese Verstärker in Studios heute so geschätzt werden.

In Anlehnung an die entsprechenden amerikanischen Designs ermöglicht der
zusätzliche Gain der EF86 des Artisan 30 eine stärkere Aussteuerung der Endstufe
zwecks Erzielung einer dichteren Kompression und einer komplexen harmonischen
Verzerrung. Die EF86 verleiht dem Kanal 2 auch sehr spezielle Kompressions- und
Verzerrungsnuancen und macht ihn so zu einem Traumpartner für Aufnahmen.

Der 5-stufige Bass Shape-Regler für die Bassaussteuerung in der Endstufe
ermöglicht dem Nutzer, Sounds schnell und ohne Probleme aus der breiten
Klangpalette zu wählen – von hellen und glasklaren bis zu druckvollen und
harmonischen Tönen.

17

Deutsch

Einleitung

Vielen Dank, dass Sie sich zum Kauf dieses handverdrahteten Blackstar Artisan 30
Comboverstärkers entschieden haben.

Der Artisan 30 ist das Ergebnis zahlloser Stunden akribischer Forschungs- und
Entwicklungsarbeit unserer erstklassigen Konstruktionsabteilung. Die Mitglieder des
im britischen Northampton ansässigen Blackstar-Teams sind selbst erfahrene
Musiker, die gemeinsam ein Ziel verfolgen: Gitarristen Produkte für die ultimativen
Selbstverwirklichung in Sachen Sound zu bieten.

Gestützt auf eine über dreißigjährige Fachkompetenz und Erfahrung im
Röhrenverstärkerbau, erreicht der Artisan 30 Combo ein neues Niveau für
handverdrahtete Gitarrenverstärker betreffend Design, Klang und Fertigungsqualität.

Alle Blackstar-Produkte werden umfangreichen Labor- und Praxistests unterzogen,
um einen kompromisslos hohen Standard in punkto Verlässlichkeit, Qualität und vor
allem SOUND zu gewährleisten!

Wenn Ihnen gefällt was Sie hören und Sie weitere Informationen zur Blackstar­Produktpalette wünschen, besuchen Sie uns bitte im Internet:
www.blackstaramps.com.

Vielen Dank!

Das Blackstar-Team

Features

Der Artisan 30 ist von den am meisten geschätzten Gitarrencombos der
Gitarrenversärkergeschichte beeinflusst. Das Design lehnt sich an das klassische 30
W / 2x12 Comboformat an, ist äußerst benutzerfreundlich und dabei extrem flexibel
in Funktionalität und Sound.

Die handverdrahtete Artisan-Serie genügt absolut höchsten Maßstäben in Sachen
handwerkliches Können und „Boutique“-Klang. Unter der Betonung von Einfachheit
und akustischer Reinheit sind die einzelnen Features verfeinert worden, damit sie
dem Künstler ein maximales Spektrum an Referenz-Vintageklängen bieten. Dies wird
durch eine Elektronikschaltung erreicht, die perfekt mit den edelsten zur Verfügung
stehenden Komponenten und Materialien harmoniert.

Der Artisan 30 hält ein Leben lang und vereint mühelos Vintage-Sounds mit
Strapazierfähigkeit und praxiserprobter Zuverlässigkeit. Die Bauweise in Punkt-zu­Punkt-Verdrahtung, das geschweißte Stahlgehäuse und die keilgezinkte Box aus
Birkensperrholz werden ergänzt durch einen wunderschönen Tolexbezug in
Vintagerot und eine Bedienplatte aus geätztem Aluminium.

16

Deutsch