Black & Decker VPX1301, 90520983 User Manual

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZADE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

1111 VVVVPPPPXX

TTTTMM

CCCCUUUUTTTT SSSSAAAAWW

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A

SUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

HANK

YOU

FOR

CHOOSING

LACK

&&D

ECKER

OOTTOOWWW

WWW

LACKAND

ECKER

COM

WNER

TTOOREGISTER

YOUR

NEW

PRODUCT

Catalog Number VPX1301

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 1

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions

can cause you to lose control

2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools.

Unmodified

plugs and matching outlets will reduce risk of electric shock

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool

will increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

A moment of inattention while operating power tool

may result in serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position before

plugging in.

Carrying power tools with your finger on the switch or plugging in power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of these devices

can reduce dust-related hazards.

4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was designed.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 2

b) Do not use the power tool if the switch does not turn it on and off.

Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use.

Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a hazardous situation.

5) Battery tool use and care a) Ensure the switch is in the off position before inserting battery pack.

Inserting

the battery pack into power tools that have the switch on invites accidents.

b) Recharge only with the charger specified by the manufacturer.

A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

c) Use power tools only with specifically designated battery packs.

Use of any

other battery packs may create a risk of injury and fire.

d) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals

together may cause burns or a fire.

e) Under abusive conditions, liquid may be ejected from the battery, avoid contact.

If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

6) Service a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord.

Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

• Use clamps or other practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body is unstable and may lead to loss

of control.

• When working on a ladder or on scaffolding be sure to lay the tool down on its side

when not in use.

Some tools with large battery packs will stand upright but may be easily

knocked over.

• Keep hands away from cutting area.

Never reach underneath the material for any reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers or thumb into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the saw by gripping the shoe.

• Keep blades sharp.

Dull blades may cause the saw to swerve or stall under pressure.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 3

• When cutting pipe or conduit

ensure that they are free from water, electrical wiring, etc.

• Do not touch the workpiece or the blade immediately after operating the tool.

They

can become very hot.

• Do not use in rain or wet conditions.

WARNING: ALWAYS USE SAFETY GLASSES.

Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3)

• ANSI S12.6 (S3.19) hearing protection

• NIOSH/OSHA respiratory protection

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA). Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

• When using an extension cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.

7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m

Wire Size AWG

18 18 16 16 14 14 12

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 4

• The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current

o ................no load speed

................Class I Construction ..................earthing terminal

....................(grounded) ................safety alert symbol

................Class II Construction …/min ..........revolutions or reciprocation

....................(double insulated) ....................per minute

s/min............strokes per minute

FUNCTIONAL

DESCRIPTION - Figure A

1. On/off switch

2. Lock-off button

3. Shoe

4. Blade clamp release lever

5. Blade

6. Battery compartment

7. Battery release button

(on battery)

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 5

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for

battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery

pack, and product using battery pack.

WARNING: Burn hazard.

To reduce the risk of injury, charge only

Black & Decker VPX

batteries. Other types of batteries may burst causing personal injury and damage.

CAUTION:

Under certain conditions, with the charger plugged in to the power supply, the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

WARNING: Shock hazard.

Do not allow any liquid to get inside charger.

• DO NOT attempt to charge the battery pack with anything other than a

Black & Decker VPX

branded charger. Black & Decker VPX

chargers and

battery packs are specifically designed to work together.

• These chargers are not intended for any uses other than charging

Black & Decker VPXTMrechargeable batteries.

Any other uses may result in risk of

fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger or when

disconnecting cords using the daisy chain feature.

This will reduce risk of damage

to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 6

• Do not use an extension cord unless it is absolutely necessary.

Use of improper

extension cord could result in risk of fire, electric shock, or electrocution.

• An extension cord must have adequate wire size (AWG or American Wire Gauge)

for safety.

The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size.

• Do not operate charger with damaged cords or plugs

— have them replaced

immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way.

• Do not disassemble charger.

Incorrect reassembly may result in a risk of electric

shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This will

reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• The charger is designed to operate on standard household electrical power

(120 Volts). Do not attempt to use it on any other voltage.

• See instruction manual for use in countries other than the U.S.A.

• This power unit is intended to be correctly orientated in a vertical or floor

mount position.

SAVE THESE INSTRUCTIONS

INTRODUCTION

Black & Decker VPX

chargers are designed to charge Black & Decker VPX

battery packs in approximately 5-6 hours. The charger requires no adjustment and is designed to be as easy as possible to operate. Simply place your battery pack into the receptacle of a plugged in charger and it will automatically charge the pack. As you add new chargers to your Black & Decker VPXTMsystem, utilize the “daisy chain” feature to power multiple chargers from a single outlet.

IMPORTANT SAFETY INSTRUCTION FOR BATTERY PACKS

WARNING:

For safe operation, read this manual and manuals originally supplied with

tool before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack even if it is severely damaged or is

completely worn out.

The battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs are burned.

• Do not charge or use battery in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust.

Inserting or removing the battery from the

charger may ignite the dust or fumes.

• If battery contents come into contact with the skin, immediately wash area with

mild soap and water.

If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory irritation.

Provide fresh air.

If symptoms persists, seek medical attention.

WARNING: Burn hazard.

Battery liquid may be flammable if exposed to spark or flame.

• Charge the battery packs only in

Black & Decker VPX

chargers.

• DO NOT splash or immerse in water or other liquids.

This may cause premature cell

failure.

• Do not store or use the tool and battery pack in locations where the temperature

may reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).

WARNING:

Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to service center for recycling.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 7

WARNING: Fire hazard. Do not store or carry battery so that metal objects can

contact exposed battery terminals.

For example, do not place battery in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like.

The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.

STORAGE RECOMMENDATIONS

1. Always store batteries charged.

2. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.

3. Recharge discharged batteries as soon as possible after use or battery life may

be greatly diminished.

CHARGING PROCEDURE

1. Plug the charger into an appropriate outlet before inserting the battery pack.

2. Insert the battery pack into the charger (figure B). Be sure the pack is fully seated in the charger. While charging, the red (charging) LED will flash continuously (slowly) indicating that the charging process has started.

3. The completion of charge is indicated by the red LED becoming solid. (approximately 5-6 hours) The pack is fully charged and may be used at this time or left on the charger.

4. Recharge discharged batteries as soon as possible after use or battery life may

be greatly diminished.

CHARGE INDICATORS Replace Pack:

These chargers are designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack. If problem persists, try a different battery pack to determine if the charger is OK. If the new pack charges correctly, then the original pack is defective and should be returned to a service center for recycling. If the new battery pack gives the same trouble indication as the original, have charger tested at an authorized service center. Note: It may take as long as fifteen minutes for the charger to determine that the pack is defective.

If the battery pack is too hot or too cold, the LED will alternately blink fast and slow, one flash at each speed and repeat.

DAISY CHAIN (FIGURE C)

Single and dual port chargers can be electrically connected in any order up to a maximum of 4 chargers. Each charger has a power-in cord (which plugs into the electrical outlet) and a power-out cord (which plugs into the next charger).

To connect chargers in a daisy chain:

1. Plug the power-in cord into an electrical outlet.

2. Remove the power-in cord from the next charger and plug in the power-out cord from the charger that is now plugged into the outlet.

3. Repeat this process for the remaining chargers.

Chargers that are daisy chained together operate independently as though each one was plugged into a sperate outlet therefore a battery can be removed from anywhere along the daisy chain without affecting the other chargers.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected indefinitely with the LED illuminated. You may see the LED return to flashing (charging) state, as the charger will occasionally “top off “ the battery charge.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 8

IMPORTANT CHARGING NOTES

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°C- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

Note: The charger will not charge a battery pack if the pack

temperature is below approximately 32°F (0°C) or above 122°F (50°C). The battery pack should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down.

2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly: a. Check current at receptacle by plugging in a lamp or other appliance b. Check to see if receptacle is connected to a light switch which turns power off when

you turn out the lights.

c. Move charger and battery pack to a location where the surrounding air temperature

is approximately 65°F - 75°F (18°C- 24°C).

d. If charging problems persist, take the tool, battery pack and charger to your local

service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard.

Do not allow any liquid to get inside charger.

CAUTION:

Never attempt to open the battery pack for any reason. If the plastic housing

of the battery pack breaks or cracks, return to a service center for recycling.

TO MAXIMIZE BATTERY LIFE:

1. Remove the batteries from the charger after the charging is completed.

2. Store the batteries at room temperature or below.

3. Recharge discharged batteries within 1 week. Battery life will be greatly diminished if the battery sits too long after being discharged.

OPERATING INSTRUCTIONS

WARNING:

Always use proper eye protection that conforms to ANSI Z87.1 (CAN/CSA

Z94.3) while operating this power tool.

NOTE: Battery pack performance will decrease under heavy use conditions when temperature is below 32°F (0°C). As the battery cells heat up the performance will improve.

INSTALLING AND REMOVING THE BATTERY PACK (FIGURE D,E)

CAUTION:

Make certain the lock-off button is engaged to prevent switch actuation before

removing or installing battery.

Installing the battery pack:

Insert the metal terminal end of the battery pack into the product until you hear the lock snap into place and the VPX

logo shows through the window as shown in figure D.

CAUTION: The battery can only be inserted in one direction. If the battery does not fit,

remove and reverse the orientation. Do not force it.

Removing the battery pack:

Press the release button as shown in figure E and firmly pull the battery pack out of the handle. Insert the battery pack into the charger (figure B) as described in the charger section of this manual.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 9

TRIGGER SWITCH (FIGURE F)

The tool is equipped with a switch lock-off feature to prevent unintentional operation.

• To operate the tool, slide the switch lock-off button (2) back and hold it as you pull the on/off switch (1).

• After the tool is running, release the switch lock-off button. The tool will continue to run as long as the trigger is depressed.

• To turn off, release the trigger switch. There is no provision for locking the tool on.

• Hold saw firmly with one hand or both hands (figure H) while cutting. Whenever possible, the saw shoe must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage.

BLADE CLAMP RELEASE LEVER (FIGURE G)

The Black & Decker VPX1301 accepts both T-shank and universal shank jig saw blades. 1mm or thicker blade recommended.

CAUTION: Recently used blades may be hot.

To install blade into saw:

• Push down on the blade clamp release lever to its full open position as shown in Figure G.

• Insert blade shank from the front.

• Release the blade clamp release lever.

To remove blade from saw:

• Push down on the blade clamp release lever to its full open position.

• Remove blade.

• Release the blade clamp release lever.

WOOD CUTTING

WARNING:

Use extra caution when cutting overhead and pay particular attention to overhead wires which may be hidden from view. Anticipate the path of falling branches and debris ahead of time.

WARNING:

Inspect work site for hidden gas pipes, water pipes, or electrical wires before making blind or plunge cuts. Failure to do so may result in explosion, property damage, electric shock, and/or serious personal injury.

• Before cutting any type of wood, use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

• Place shoe firmly against work to be cut.

• Switch on saw motor before applying pressure.

• Whenever possible, the shoe must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage.

METAL CUTTING (FIGURE H)

• Use a finer blade for ferrous metals and a coarse blade for non-ferrous materials.

• In thin gauge sheet metals it is best to clamp wood to both sides of sheet. This will ensure a clean cut without excess vibration or tearing of metal.

• Avoid forcing cutting blade as this reduces blade life and causes costly blade breakage.

• When cutting metal piping, do not cut directly through the pipe as you would saw a wooden dowel. Instead, cut around the circumference of the pipe to avoid pinching the blade. Only one section of the blade should be in contact with the pipe.

NOTE: You should spread a thin film of oil or other coolant along the line ahead of the saw cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

POCKET CUTTING - WOOD ONLY (FIGURE I)

Pocket cutting is used to cut a hole in a piece of material without cutting from the side.

• Measure the surface area to be cut and mark clearly with a pencil.etc.

• Tilt saw forward and rest front of the shoe on material to be cut.

• Switch the tool on. Grip the handle firmly and raise the back edge of tool until the blade cuts smoothly into the material. Always be sure blade reaches its complete depth before starting to cut.

• Allow the blade to come to a complete stop before lifting saw from material.

• When starting each new cut, repeat the above steps.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 10

TREE TRIMMING

• Use a coarse blade when cutting tree limbs. Hold shoe firmly against tree branch. If possible, cut close to the trunk to minimize movement of the branch.

PROJECT TIPS

• Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while cutting.

• Place blade and shoe lightly against work to be cut. This will improve operator control and minimize vibration.

• For longer blade life, use bi-metal blades. These utilize a carbon steel back welded to high speed steel teeth making the blade more flexible and less prone to breaking.

• Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

• Switch on saw motor and allow it to obtain maximum speed before applying pressure

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Battery pack not installed properly. • Check battery pack installation.

• Battery pack not charged. • Check battery pack charging requirements.

• Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into charger until red LED appears.

• Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details.

• If chargers are daisy chained together check all connections.

• Check current at receptacle by plugging in a lamp or other appliance.

• Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

• Surrounding air temperature. • Move charger and battery to a surrounding air temperature of above 40 degrees F (4,5°C) or below 105 degrees F (+40,5°C).

• Battery pack too hot or too cold. • The charger will not charge a battery pack if the cell temperature is below approximately 32° F (0° C) or above 140° F (60° C). The battery pack should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down.

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544 6986.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 11

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could

be hazardous.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lithium ion battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker.

RBRC™ in cooperation with Black & Decker and other battery users, has established programs in the United States to facilitate the collection of spent ion batteries. Help protect our environment and conserve natural resources by returning the spent lithium ion battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the

Rechargeable Battery Recycling Corporation.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 12

+ 26 hidden pages