BLACK & DECKER V1250 User Manual

1

2

3

Powerful Solutions TM

www.blackanddecker.co.uk

V1250

V1250N

V4800
V4810
V4820
V7210
V9650

1

English (Original instructions) 5

2

4

5

6

7

8

9

V9650

1

2

3

A B

C D

E F

3

10

11

G

12

H

4

Intended use

Your Black & Decker Dustbuster® hand
held vacuum cleaner has been designed
for light dry vacuum cleaning purposes.
This product is intended for household
use only.

Safety instructions

u Warning! When using battery-

powered appliances, basic safety
precautions, including the following,
should always be followed to reduce

the risk of re, leaking batteries,

personal injury and material damage.

u Read this manual carefully before

using the appliance.

u The intended use is described in this

manual. The use of any accessory or
attachment or the performance of
any operation with this appliance
other than those recommended in
this instruction manual may present
a risk of personal injury.

u Retain this manual for future reference.

Using your appliance

u Do not use the appliance to pick up

liquids or any materials that could

catch re.

u Do not use the appliance near water.

Do not immerse the appliance in water.

u Never pull the charger lead to

disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.

After use

u Unplug the charger before cleaning

the charger or charging base.

u When not in use, the appliance

should be stored in a dry place.
Children should not have access to
stored appliances.

Inspection and repairs

u Before use, check the appliance for

damaged or defective parts. Check
for breakage of parts, damage to
switches and any other conditions
that may affect its operation.

u Do not use the appliance if any part

is damaged or defective.

u Have any damaged or defective parts

repaired or replaced by an authorised
repair agent.

u Regularly check the charger lead for

damage. Replace the charger if the
lead is damaged or defective.

u Never attempt to remove or replace

any parts other than those specied

in this manual.

Residual risks

Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use, etc.

Even with the application of the relevant
safety regulations and the implementation
of safety devices, certain residual risks
can not be avoided. These include:

u Injuries caused by touching any

rotating/moving parts.

u Injuries caused when changing any

parts, blades or accessories.

u Injuries caused by prolonged use of

a tool. When using any tool for
prolonged periods ensure you take
regular breaks.

u Impairment of hearing.
u Health hazards caused by breathing

dust developed when using your tool
(example: working with wood,
especially oak, beech and MDF).

Safety of others

u This appliance is not intended for use

by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by
a person responsible for their safety.

u Children should be supervised to

ensure that they do not play with the
appliance.

5

Additional safety instructions for
batteries and chargers

Batteries

u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not expose the battery to heat.
u Do not store in locations where the

temperature may exceed 40 °C.

u Charge only at ambient temperatures

between 10 °C and 40 °C.

u Charge only using the charger

provided with the appliance/tool.

u When disposing of batteries, follow

the instructions given in the section
"Protecting the environment".

u Do not damage/deform the battery

pack either by puncture or impact, as

this may create a risk of injury and re.

u Do not charge damaged batteries.
u Under extreme conditions, battery

leakage may occur. When you notice
liquid on the batteries, proceed as
follows:

u Carefully wipe the liquid off using

a cloth. Avoid skin contact.

u In case of skin or eye contact, follow

the instructions below.

Warning! The battery uid may cause

personal injury or damage to property.
In case of skin contact, immediately rinse
with water. If redness, pain or irritation
occurs seek medical attention. In case of
eye contact, rinse immediately with clean
water and seek medical attention.

u If the supply cord is damaged, it must

be replaced by the manufacturer or an
authorised Black & Decker Service
Centre in order to avoid a hazard.

u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
u The appliance/tool/battery must be

placed in a well ventilated area when
charging.

Electrical safety

Your charger has been designed for a

specic mains voltage. Always check that

the mains voltage corresponds to the
voltage on the rating plate.

Your charger is double

#

insulated.

Features

1. On/off switch

2. Release button

3. Dust bowl

Fig. A

4. Charging base

5. Charger

Installation

Fitting the charging base to the wall

The charging base can be tted to the

wall to provide a convenient storage and
charging point for the appliance.

Chargers

Your charger has been designed for a

specic voltage. Always check that the

mains voltage corresponds to the voltage
on the rating plate.

Warning! Never attempt to replace the
charger unit with a regular mains plug.

u Use your Black & Decker charger

only to charge the battery in the
appliance/tool with which it was
supplied. Other batteries could burst,
causing personal injury and damage.

u Never attempt to charge non-

rechargeable batteries.

6

Before rst use

Before rst use, the battery must be

charged for at least 24 hours.

Use

Charging the battery (g. D)

u Make sure that the appliance is

switched off. The battery will not be
charged with the on/off switch in the
on position.

u Place the appliance on the charging

base as shown.

u Plug in the charger.
u Switch on at the mains.

u Leave the appliance to charge for at

least 24 hours.
Whilst charging, the charger may become
warm. This is normal and does not
indicate a problem. The appliance can be

left connected to the charger indenitely.

Important! Place the appliance on the
charging base whenever it is not in use.
Do not charge the battery at ambient
temperatures below 10 °C or above
40 °C.

Operating the appliance (g. E)

u To switch on, slide the on/off switch

(1) forward.

u To switch off, slide the on/off switch

back.

Accessories (g. B & C)

V1250/V4810/V4820/V7210/V9650

These models are supplied with the
following accessories:

u a hard brush (6) for furniture and

stairs (not for V4820)

u a crevice tool (7) for conned spaces
u a soft brush (8) for keyboards and

lamp shades (V4820)

V1250/V9650

Two additional accessories are stored in
a portable caddy located in the charging
base:

u a soft brush (8) for keyboards and

lamp shades

u an extendable crevice tool (9) for

longer reach in conned spaces

V1250N

This model is not supplied with accessories.

To t an accessory, proceed as follows:

u Take the accessories from the

appliance.

u Insert the appropriate accessory into

the front of the appliance.

Cleaning and maintenance

Warning! Regularly clean the lters.

Cleaning the dust bowl and lters
(g. F & G)

The lters are re-usable and should be

cleaned regularly.

u Press the release button (2) and

remove the dust bowl (3).

u Empty the dust bowl.
u Remove the lters (10) by twisting

them clockwise.

u Brush any loose dust off the lters.
u Wash the lters in warm, soapy

water. The bowl can also be washed
if necessary. Do not immerse the
appliance in water.

u Make sure the dust bowl and lters

are dry.

u Ret the lters (10) onto the appliance,

twisting them counterclockwise until
they lock into place.

u Ret the dust bowl onto the appliance.

Make sure the dust bowl clicks into
place.

Warning! Never use the appliance

without the lters. Optimum dust collection
will only be achieved with clean lters

and an empty dust bowl.

Replacing the lters

The lters should be replaced every 6 to

9 months and whenever worn or

damaged. Replacement lters are

available from your Black & Decker
dealer (cat. no. VF20).

u Remove the old lters as described

above.

u Fit the new lters as described above.

Maintenance

Your tool has been designed to operate
over a long period of time with a minimum
of maintenance. Continuous satisfactory
operation depends upon proper tool care
and regular cleaning.

Warning! Before performing any
maintenance, switch off and unplug the
tool.

7

u Switch off and unplug the appliance/

tool.

u Or switch off and remove the battery

from the appliance/tool if the appliance/

tool has a separate battery pack.

u Or run the battery down completely

if it is integral and then switch off.

u Unplug the charger before cleaning it.

Your charger does not require any

maintenance apart from regular

cleaning.

u Regularly clean the ventilation slots

in your tool using a soft brush or dry

cloth.

u Regularly clean the motor housing

using a damp cloth. Do not use any

abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it

to remove any dust from the interior

(when tted).

Protecting the environment

Separate collection. This product

Z

must not be disposed of with
normal household waste.

Should you nd one day that your
Black & Decker product needs
replacement, or if it is of no further use to
you, do not dispose of it with household
waste. Make this product available for
separate collection.

Separate collection of used

z

products and packaging allows
materials to be recycled and
used again. Re-use of recycled
materials helps prevent
environmental pollution and
reduces the demand for raw
materials.

Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by
the retailer when you purchase a new
product.

Black & Decker provides a facility for the
collection and recycling of Black & Decker
products once they have reached the end
of their working life. To take advantage of
this service please return your product to
any authorised repair agent who will
collect them on our behalf.

You can check the location of your nearest
authorised repair agent by contacting your

local Black & Decker ofce at the address

indicated in this manual. Alternatively,
a list of authorised Black & Decker repair
agents and full details of our after-sales
service and contacts are available on the
Internet at: www.2helpU.com

Battery (g. H)

Black & Decker batteries can

Z

be recharged many times.
At the end of their useful life,
discard batteries with due care
for our environment.

If you want to dispose of the product
yourself, the battery must be removed
as described below and disposed of in
accordance with local regulations.

u Discharge the battery by operating

the appliance until the motor stops.
The battery is located under the back
end of the appliance.

u Remove the crevice tool from the

accessory holder.

u Push the slider (12) towards the front

of the product.

u Remove the accessory holder.
u Strike the product on a rm and stable

surface as shown in g. H to dislodge

the battery.

u Place the battery in suitable packaging

to ensure that the terminals cannot

be short-circuited.

u Take the battery to your service agent

or a local recycling station.
Warning! Once removed, the battery

cannot be retted.

8

Technical data
V1250 H2 V1250N H2

Voltage V 12 12
Weight kg 1.8 1.7

V4800 H2 V4810 H2

Voltage V 4.8 4.8
Weight kg 1.2 1.2

V4820 H2 V7210 H2

Voltage V 4.8 7.2
Weight kg 1.2 1.4

V9650 H2

Voltage V 9.6
Weight kg 1.6

Charger
5102404-08 VA090020D

Model V48 V72
Input voltage VAC 230/240 230
Output voltage VAC 6.4 9
Amperage mA 250/265 200
Approx.
charging time h 24 24
Weight kg 0.3 0.3

5102404-11 CHA002014*

Model V96 V12
Input voltage VAC 230/240 100-240
Output voltage VAC 14 7.2-24 Vdc
Amperage mA 130/140 85
Approx.
charging time h 24 24
Weight kg 0.3 0.3

Level of sound pressure according to EN 60745:

Sound pressure (L

Vibration total values (triax vector sum) according

to EN 60745:

Hand/arm weighted vibration 2.5 m/s

) 85 dB(A), uncertainty (K) 3 dB(A)

pA

2

Guarantee

Black & Decker is condent of the quality

of its products and offers an outstanding
guarantee. This guarantee statement is
in addition to and in no way prejudices
your statutory rights. The guarantee is
valid within the territories of the Member
States of the European Union and the
European Free Trade Area.

If a Black & Decker product becomes
defective due to faulty materials,
workmanship or lack of conformity, within
24 months from the date of purchase,
Black & Decker guarantees to replace
defective parts, repair products subjected
to fair wear and tear or replace such
products to ensure minimum inconvenience
to the customer unless:

u The product has been used for trade,

professional or hire purposes;

u The product has been subjected to

misuse or neglect;

u The product has sustained damage

through foreign objects, substances

or accidents;

u Repairs have been attempted by

persons other than authorised repair

agents or Black & Decker service staff.
To claim on the guarantee, you will need
to submit proof of purchase to the seller or
an authorised repair agent. You can check
the location of your nearest authorised
repair agent by contacting your local

Black & Decker ofce at the address

indicated in this manual. Alternatively,
a list of authorised Black & Decker repair
agents and full details of our after-sales
service and contacts are available on the
Internet at: www.2helpU.com

Please visit our website
www.blackanddecker.co.uk to register
your new Black & Decker product and to
be kept up to date on new products and
special offers. Further information on the
Black & Decker brand and our range of
products is available at

www.blackanddecker.co.uk

9

H2

TYP.

13 - 01 - 10

101

V1250N

Partial support - Only parts shown available

Nur die aufgefuerten teile sind lieferbar

Reparation partielle - Seules les pieces indiquees sont disponibles

Supporto parziale - Sono disponibili soltanto le parti evidenziate

Solo estan disponibles las peizas listadas

So se encontram disponiveis as pecas listadas

Gedeeltelijke ondersteuning - alleen de getoonde onderdelen

zijn beschikbaar

103

104

170

www.2helpU.com

160

E15938

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/productregistration or

send your name, surname and product code to Black & Decker in your country.

Australia

Black & Decker (Australia) Pty. Ltd. Tel. [phone]
20 Fletcher Road, Mooroolbark, Fax [phone]
Victoria, 3138

New Zealand

Black & Decker Tel. [phone]
5 Te Apunga Place Fax [phone]
Mt Wellington
Auckland 1060

United Kingdom

Black & Decker Tel. [phone]
210 Bath Road Fax [phone]
Slough, Berkshire SL1 3YD Helpline 01753 574277

S/T-12/0990558582 REV 0