Black & Decker TV380, TV310, TV300 User Manual

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model. Accessories

that may be suitable for one tool, may become hazardous when used on another tool.

Service

•Tool service must be performed only by qualified repair personnel. Service or maintenance

performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance
Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and

shock the operator.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activ-

ities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your expo­sure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles.
The label on your tool may include the following symbols.

V ..............volts

A ..............amperes

Hz ............hertz

W..............watts

min ............minutes

..............alternating current

..........direct current

no..............no load speed

..............Class II Construction

…/min ......revolutions or reciprocation per minute

..............earthing terminal

............safety alert symbol

SAFETY WARNINGS AND INSTRUCTIONS: DRILLS

• Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch.

• Hold drill firmly to control the twisting action of the drill. If your drill is equipped with a side handle,

always use the side handle.

WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall.

Grip the drill firmly to control the twisting action and prevent loss of control which could cause personal
injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before
re-starting.

• Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill

chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using
a keyless chuck, hand tighten firmly.

SAVE THESE INSTRUCTIONS

MOTOR

Be sure your power supply agrees with nameplate marking. 120 volts, AC only means your tool may be
operated only with alternating current and never with direct current. Voltage decrease of more than 10% will
cause loss of power and overheating. All tools are factory tested; if this tool does not operate, check the power
supply.

USE OF EXTENSION CORDS

Make sure the extension cord is in good condition before using. Always use the proper size extension cords
with the tool – that is, proper wire size for various lengths of cord and heavy enough to carry the current the
tool will draw. Use of an undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. For proper size cords see chart below.

ASSEMBLY/ADJUSTMENT SET-UP

WARNING: Always unplug drill from power supply before any of the following operations.

SIDE HANDLE (TV 380 ONLY)

•Your drill is equipped with a side handle, it must be installed properly in order to control the drill.

•Insert bolt into recessed hole with molded hex shape, making sure that hex head is seated fully to prevent

bolt from turning.

• Place circular opening over drill chuck and onto front of drill gear case.

• Place the drill on its side and holding the bolt head with your finger, thread handle onto bolt. The handle

now has a full range of 360 degrees around the drill.

OPERATING INSTRUCTIONS

WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety

warnings and instructions prior to using tool.

SWITCH

To turn the drill ON squeeze the trigger switch. The farther the trigger is depressed, the higher the speed of the
drill. To turn the tool OFF release the trigger switch. The drill can be locked ON (maximum RPM only) for
continuous use by squeezing the trigger while pushing in on the locking button (Fig.1). Hold the locking button
in while you release the trigger switch and then release the locking button. The drill will continue to run. To turn
the drill OFF from a locked ON condition, squeeze and release the trigger.

WARNING: The drill should only be locked ON when it is held stationary in a drill press stand or other

means; NOT BY HAND! Never unplug the tool with the locking feature engaged. To do so will cause the tool to
start immediately the next time it is plugged in.

FORWARD/REVERSE (TV300, TV310)

To select forward rotation push the switch control lever (Fig.1) to the RIGHT (when viewed from the chuck end).
To select reverse push the lever to the LEFT (when viewed from the chuck end). After all reversing operations,
switch the tool to the forward running mode.

GENERAL SAFETY RULES

WARNING! Read and understand all instructions. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can
cause you to lose control.

Electrical Safety

•Grounded tools must be plugged into an outlet properly installed and grounded in accordance
with all codes and ordinances. Never remove the grounding prong or modify the plug in any
way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to
whether the outlet is properly grounded. If the tools should electrically malfunction or break

down, grounding provides a low resistance path to carry electricity away from the user.
Applicable only to Class I (Grounded) tools.

• Double insulated tools are equipped with a polarized plug (one blade is wider than the other.)
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double Insulation eliminates the need for the three wire

grounded power cord and grounded power supply system. Applicable only to Class ll tools.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in serious personal injury,

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught
in moving parts.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your
finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat,
or hearing protection must be used for appropriate conditions.

Tool Use and Care

• Use clamps or other practical way to secure and support the workpiece to a stable platform.

Holding the work by hand or against your body is unstable and may lead to loss of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job better
and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the
tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the
hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with
sharp cutting edges are less likely to bind and are easier to control.

KEY INFORMATION YOU SHOULD KNOW:

•Reversing drills must be switched into forward or reverse in order to operate. They
will not run with the switch control lever in the center position.

•Securely tighten chuck jaws using all three holes except with keyless chucks which
should be securely hand tightened.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

3333////8888”””” ((((11110000mmmmmmmm)))) DDDDrrrriiiillllllllssss

TTTTVVVV333300000000,,,, TTTTVVVV3333111100

00

1111////2222”””” ((((11113333mmmmmmmm)))) DDDDrrrriiiillllll

ll

TTTTVVVV3333888800

00

Catalog Numbers TV300, TV310, TV380

1-800-544-6986

CAT. NO. TV300, TV310, TV380 FORM NO. 389994-00

Copyright © 2000 Black & Decker (SEP00-1) Printed in U.S.A.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 25 26-50 51-100 101-150
240V 50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage
Than Than
0-6 18 16 16 14
6-10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

1

3

Lock-on button

Bouton de verrouillage

Boton de encendido permanente

Switch control lever

Levier de commande de l'interrupteur

Palanca de control

2

NOTE: WHEN THE SWITCH CONTROL LEVER IS IN THE CENTER POSITION THE DRILL WILL NOT OPERATE.
DO NOT FORCE TRIGGER. SELECT FORWARD OR REVERSE BEFORE TURNING DRILL ON.

FORWARD/REVERSE (TV380 ONLY)

To select forward rotation push the switch control lever (Fig.1) to the LEFT (when viewed from the chuck end). To
select reverse push the lever to the RIGHT (when viewed from the chuck end). After all reversing operations,
switch the tool to the forward running mode.
NOTE: WHEN THE SWITCH CONTROL LEVER IS IN THE CENTER POSITION THE DRILL WILL NOT OPERATE.
DO NOT FORCE TRIGGER. SELECT FORWARD OR REVERSE BEFORE TURNING DRILL ON.

CHUCK & KEY OPERATION (TV300, TV310)

Turn chuck collar to open chuck jaws. Place bit in chuck as far as it will go. Tighten chuck collar by hand. Place
chuck key in each of the three holes, and tighten in clockwise direction (Fig. 2). Tighten chuck with all three
holes to prevent slippage.

KEYLESS CHUCK OPERATION (TV380)

To attach accessories, grasp the rear half of the chuck with one hand and use your other hand to rotate the
front half in the counterclockwise direction (Fig. 3). Insert the bit or other accessory fully into the chuck, and
tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as
viewed from the chuck end.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the

chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing
accessories.

DRILLING

• Make sure switch turns drill on and off.

• Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill
chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using
a keyless chuck, hand tighten firmly.

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the Safety Instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slip­ping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much
as to stall the motor or deflect the bit.

• Hold the drill firmly to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAM­AGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the
hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

• Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled
dry. The lubricants that work best are sulphurized cutting oil or lard oil. Bacon grease will also serve.

• When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out frequently to clear
chips from the flutes.

WARNING: It is important to support the work properly and to hold the drill firmly to prevent loss of control

which could cause personal injury. If you have any questions on how to properly operate tool, call:

1-800-544-6986.

KEYED CHUCK REMOVAL (TV300, TV310)

UNPLUG DRILL. Place chuck key in any one of the three holes in the chuck. Strike the key sharply in a

counterclockwise direction (when viewed from the front of the tool). This will loosen the chuck so that it can be
removed by hand.

KEYLESS CHUCK REMOVAL

(TV380)

UNPLUG DRILL.Tighten the chuck around the shorter end of a hex key (not supplied) of 1/4" (6.4mm) or

greater size. Using a soft hammer, strike key sharply in a counterclockwise direction (when viewed from the
front of the tool). This will loosen the chuck so that it can be unscrewed by hand.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be
performed by authorized service centers or other qualified service organizations, always using identical
replacement parts.

LUBRICATION

MASTER MECHANIC tools are properly lubricated at the factory and are ready for use.

ACCESSORIES

A full array of accessories for use with your tool are available from your local dealer or authorized service
center.

CAUTION: The use of any accessory or attachment not recommended may be hazardous.

TWO YEAR QUALITY GUARANTEE

This product is warranted for two years against any defects in material and workmanship. If defective, the
product will be repaired or replaced free of charge. Simply provide proof of purchase and return the tool to
your place of purchase. Normal wear or damage due to abuse, mishandling or unauthorized repair is not
covered. This warranty does not apply to accessories. This warranty gives you specific legal rights and you
may have other rights which vary from state to state.

30 DAY SATISFACTION GUARANTEE

If, for any reason, you are not completely satisfied with the performance or results of this product, within thirty
days of original purchase, it will be repaired or replaced free of charge. Simply provide proof of purchase and
return the tool to your place of purchase.

If your tool requires out of warranty repairs, you may send or take your tool to a Black & Decker owned
Service Center. Black & Decker Service Centers are listed under “Tools-Electric” in the yellow pages of the
phone directory or you may call 1-800-544-6986 for information on your nearest Service Center.

AVERTISSEMENT : MESURES DE SÉCURITÉ

AVERTISSEMENT :Lire et comprendre toutes les directives. Le non-respect de toutes les directives suivantes

présente des risques de secousses électriques, d'incendie ou de blessures graves.

CONSERVER CES MESURES.

ZONE DE TRAVAIL

• S'assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et des endroits sombres

présentent des risques d'accidents.

• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme celles dégagées par des
liquides, des gaz ou des poussières inflammables). Les étincelles générées par le moteur des outils

électriques peuvent enflammer les poussières ou les vapeurs.

• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu'on utilise un outil électrique.

Une distraction peut entraîner la perte de maîtrise de l'outil.

MESURES DE SÉCURITÉ RELATIVES À L'ÉLECTRICITÉ

• Les outils à double isolation comportent une fiche polarisée (une lame plus large que l'autre). La fiche
n'entre que d'une façon dans une prise polarisée. Lorsque la fiche n'entre pas à fond dans la prise,
essayer de nouveau après avoir inversé les broches de la fiche. Si la fiche n'entre toujours pas dans la
prise, communiquer avec un électricien certifié afin de faire installer une prise polarisée. Ne modifier en
aucune façon la fiche. La double isolation élimine le besoin d'un cordon trifilaire mis à la terre et d'un

système d'alimentation mis à la terre.

• Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs, des cuisinières et des
réfrigérateurs. Les risques de secousses électriques sont plus élevés si le corps de l'utilisateur est mis à la terre.

•Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration d'eau dans l'outil

augmente les risques de secousses électriques.

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter l'outil ni tirer sur le
cordon pour débrancher l'outil. Éloigner le cordon des sources de chaleur, des flaques d'huile, des arêtes
tranchantes et des pièces mobiles. Remplacer immédiatement les cordons endommagés. Les cordons

endommagés augmentent les risques de secousses électriques.

• Lorsqu'on utilise un outil électrique à l'extérieur, se servir d'un cordon de rallonge prévu pour l'extérieur,
portant la mention "W-A" ou "W". Ces cordons sont conçus pour servir à l'extérieur et minimisent les

risques de secousses électriques.

SÉCURITÉ PERSONNELLE

• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu'on utilise un outil électrique. Ne pas
s'en servir lorsqu'on est fatigué ou affaibli par des drogues, de l'alcool ou des médicaments. De graves

blessures peuvent résulter d'un moment d'inattention lors de l'utilisation d'un outil électrique.

• Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des bijoux. Recouvrir la
chevelure si elle est longue. Éloigner les cheveux, les vêtements et les gants des pièces en mouvement qui

peuvent les happer.

• Éviter les démarrages accidentels. S'assurer que l'interrupteur est en position hors tension avant de
brancher l'outil. Afin d'éviter les risques de blessures, ne pas transporter l'outil avec le doigt sur l'interrupteur

ni brancher un outil dont l'interrupteur est en position sous tension.

• Enlever les clés de réglage avant de mettre l'outil sous tension. Une clé qui est laissée sur une pièce rotative
de l'outil présente des risques de blessures.

• Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s'assure d'une meilleure maîtrise de
l'outil dans des situations imprévues grâce à une position stable et un bon équilibre.

• Porter de l'équipement de sécurité. Toujours porter des lunettes de sécurité. Dans certaines conditions, il
faut porter des masques respiratoires, des chaussures antidérapantes, un casque de sécurité ou des protège­tympans.

UTILISATION ET ENTRETIEN DE L'OUTIL

• Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de soutenir la pièce à ouvrer
sur une plate-forme stable. La pièce est instable lorsqu'elle est retenue par la main ou le corps de l'utilisateur.

Cela présente des risques de perte de maîtrise de l'outil.

• Ne pas forcer l'outil. Utiliser l'outil approprié à la tâche. L'outil approprié fonctionne mieux et sûrement
lorsqu'on s'en sert à son rendement nominal.

• Ne pas se servir de l'outil lorsque l'interrupteur est défectueux. Le cas échéant, l'outil est dangereux et il
faut le réparer.

• Débrancher l'outil de la source d'alimentation avant de le régler, d'en remplacer les accessoires ou de le
ranger. On minimise de la sorte le risque de démarrage accidentel de l'outil.

• Ranger l'outil hors de portée des enfants et de toute autre personne qui n'en connaît pas le
fonctionnement. L'outil est dangereux entre les mains de ces personnes.

•Prendre soin des outils. S'assurer que les outils de coupe sont tranchants et propres. Des outils bien

entretenus à arêtes tranchantes ont moins tendance à se coincer et ils se maîtrisent mieux.

• Vérifier l'alignement et les attaches des pièces mobiles, le degré d'usure des pièces ainsi que tout autre
facteur susceptible de nuire au bon fonctionnement de l'outil. Faire réparer un outil endommagé avant de
s'en servir. Des outils mal entretenus sont la cause de nombreux accidents.

• Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires qui conviennent à un outil

peuvent présenter des risques avec un autre outil.

ENTRETIEN

• Confier l'entretien de l'outil seulement à du personnel qualifié. Le non-respect de la présente directive

présente des risques de blessures.

• Lors de l'entretien de l'outil, utiliser seulement des pièces de rechange identiques. Respecter les consignes
relatives à l'entretien du présent guide d'utilisation. Il y a risque de secousses électriques ou de blessures

lorsqu'on utilise des pièces non autorisées ou lorsqu'on ne respecte pas les consignes relatives à l'entretien.

MESURES DE SÉCURITÉ ADDITIONNELLES

• Saisir les surfaces isolées de l'outil lorsqu'on s'en sert là où il pourrait y avoir des fils sous tension et
lorsqu'il pourrait entrer en contact avec son propre fil. En cas de contact avec un fil sous tension, les

composantes métalliques à découvert de l'outil deviendraient sous tension et l'utilisateur subirait des secousses
électriques.

AVERTISSEMENT : Certains outils, tels que les sableuses électriques, les scies, les meules, les perceuses ou

certains autres outils de construction, peuvent soulever de la poussière contenant des produits chimiques
susceptibles d’entraîner le cancer, des malformations congénitales ou pouvant être nocifs pour le système
reproductif. Parmi ces produits chimiques, on retrouve :

• le plomb dans les peintures à base de plomb;

• la silice cristalline dans les briques et le ciment et autres produits de maçonnerie;

• l’arsenic et le chrome dans le bois de sciage ayant subi un traitement chimique.

Le risque associé à de telles expositions peut varier selon la fréquence avec laquelle on effectue ces travaux.
Pour réduire l’exposition à de tels produits, il faut travailler dans un endroit bien ventilé et utiliser l’équipement

TruServ

8600 W. Bryn Mawr Ave.

Chicago, IL 60631-3505

MAXIMUM RECOMMENDED CAPACITIES

Cat. # Type Steel Soft Wood Hard Wood

TV300 3/8"Drill 3/8"(9.5mm) Twist Bit 1-1/4"(31.7mm) 1"(25.4mm)
TV310 3/8"Drill 3/8"(9.5mm) Twist Bit 1-1/4"(31.7mm) 1"(25.4mm)
TV380 1/2"Drill 1/2"(12.7mm) Twist Bit 1-1/2"(38.1mm) 1-1/4"(31.7mm)

PPPPeeeerrrrcccceeeeuuuusssseeeessss ddddeeee 11110000 mmmmmmmm ((((3333////8888ppppoooo)))) eeeett

tt

PPPPeeeerrrrcccceeeeuuuusssseeeessss eeeetttt ppppeeeerrrrcccceeeeuuuusssseeeessss àààà

ppppeeeerrrrccccuuuussssssssiiiioooonnnn ddddeeee 11113333 mmmmmmmm ((((1111////2222ppppoooo))

))

Modèles TV300, TV310, TV380

RENSEIGNEMENTS IMPORTANTS

•Il faut actionner les perceuses dotées d’un inverseur de marche lorsqu’elles sont en
position de marche avant ou arrière. Elles ne fonctionnent pas en position neutre.

•Bien serrer les mâchoires du mandrin par chacun des trois trous, sauf dans le cas
des mandrins sans clé qu’il faut serrer fermement à la main.

1 800 544-6986