Black & Decker HT018 TYPE 1, HT018 TYPE 2, TR016 TYPE 1, TR016 TYPE 2, HT020 TYPE 2 Owner’s Manual

INSTRUCTIONMANUAL

Catalog Numbers

TR016, TR017, HT012, HT018, HT020, HT022, HT512,

TR016, TR017

HT012, HT018, HT020, HT512 HT022

Thank you for choosing Black & Decker!

Go to www.BlackandDecker.com/NewOwner

to register your new product.

PLEASE READ BEFORE RETURNING THIS

PRODUCT FOR ANY REASON:

IfyouhaveaquestionorexperienceaproblemwithyourBlack&Deckerpurchase,goto

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

forinstantanswers24hoursaday.

Ifyoucan'tfindtheanswerordonothaveaccesstotheinternet,

call1-800-544-6986from8a.m.to5 p.m.ESTNon.-- Fri.tospeakwithanagent.

Pleasehavethecatalognumberavailablewhenyoucall.

KEY INFORMATION YOU SHOULD KNOW:

• To insure extension cord does not come loose see Figure 8 for
proper attachment.

• In order to operate the trimmer, the lock button must first be pulled back
(see figure 9) then squeeze trigger.

VEA EL ESPAI_IOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANT|A.

ADVERTENCIA: LleASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.

Z_DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

/k WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

/k CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

/k WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using this toot reads and understands all safety

instructions and other information contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.

/_WARNING: When using electric gardening appliances, basic safety precautions

should always be followed to reduce risk of fire, electric shock, and personal injury,
including the following:

READ ALL INSTRUCTIONS.

/_ GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL

TOOLS

• AVOID DANGEROUS ENVIRONMENT - Don't use hedge trimmers in damp or wet

locations.

• DON'T USE IN RAIN.

• KEEP CHILDREN AWAY - All visitors should be kept at a safe distance from the work

area.

• DRESS PROPERLY - Don't wear loose clothing or jewelry. They can be caught in

moving parts. Use of rubber gloves and substantial footwear is recommended when
working outdoors. Wear protective hair covering to contain long hair.

• USE SAFETY GLASSES - Also use face or dustmask if operation is dusty.

• GROUND FAULT CIRCUIT INTERRUPTER (GFCl) protection should be provided on

the circuit(s) or outlet(s) to be used for the hedge trimmer. Receptacles are available
having built-in GFCI protection and may be used for this measure of safety.

• USE RIGHT APPLIANCE - Do not use appliance for any job except that for which it is

intended.

• EXTENSION CORD. To reduce the risk of electric shock use only with an extension

cord intended for outdoor use, such as SW-A, SOW-A, STW-A, STOW-A, SJW-A,
SJOW-A, SJTW-A or SJTOW-A. Make sure your extension cord is in good condition.

When using an extension cord be sure it is heavy enough to carry the current your
product will draw. An undersized extension cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table shows the correct size
to use depending on cord length and nameplate ampere rating. If in doubt, use the
next heavier gage. The smaller the gage number, the heavier the cord.

Volts
120V 0-25

240V 0-50

Ampere Rating
More Not more

Than Than
0 6 18
6 10 18
10 12 16
12 16 14

Minimum Gage for Cord Sets

Total Length of Cord in Feet

26-50 51-100 101-150

(0-7,6m)

(0-15,2m)

(7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

51-100 101-200 201-300

(15,2-30,4m) (30,4-60,9m)(60,9-91,4m)

American Wire Gage

16 16 14
16 14 12
16 14 12
12 Not Recommended

• AVOID UNINTENTIONAL STARTING - Don't carry plugged in hedge trimmer with

finger on switch. Be sure switch isoff when plugging in.

• DON'T ABUSE CORD - Never carry hedge trimmer by cord or yank it to disconnect

from receptacle. Keep cord from heat, oil, and sharp edges.

• DO NOT ATTEMPT to remove cut material or hold material to be cut when blades are

moving. Make sure trimmer switch is off when clearing jammed material from blades.
Do not grasp the exposed cutting blades or cutting edges when picking up or holding

the hedge trimmer.

• DON'T FORCE HEDGE TRIMMER - It will do the job better and with tess likelihood of

a risk of injury at the rate for which it was designed.

• DON'T OVERREACH - Keep proper footing and balance at all times.

• STAY ALERT - Watch what you are doing. Use common sense. Do not operate hedge

trimmer when you are tired.

• DISCONNECT HEDGE TRIMMER from the power supply when not in use or when

servicing or cleaning.

• STORE IDLE HEDGE TRIMMER INDOORS - When not in use, hedge trimmer should

be stored indoors in a dry and high or locked-up place- out of reach of children.

• MAINTAIN HEDGE TRIMMER WITH CARE - Keep cutting blades sharp and clean for

best performance and to reduce the risk of injury. Inspect extension cord periodically
and replace if damaged. Keep handles dry, clean and free from oil and grease.

Lubricate blades as needed (refer to maintenance section).

• CHECK DAMAGED PARTS - before further use of the hedge trimmer, a guard or

other part that is damaged should be carefully checked to determine that itwilt operate
properly and perform its intended function. Check for alignment of moving parts,

binding of moving parts, breakage of parts, mounting and any other condition that may
affect its operation. A guard or other part that is damaged should be properly repaired
or replaced by an authorized service center unless otherwise indicated elsewhere in

this manual.

Z_DANGER: Laceration hazard. Keep hands away from blades. Keep both hands on

handles when power ison.

Z_CAUTION: Laceration hazard. Blades coast after turn off.

/_ SAFETY WARNINGS: DOUBLE INSULATION

Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one double thickness of insulation between you and the tool's electrical

system. Tools built with this insulation system are not intended to be grounded. As a

result, your toot is equipped with a two prong plug which permits you to use extension

cords without concern for maintaining a ground connection.

NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting
from a possible electrical insulation failure within the toot.

Replacement parts: When servicing all tools, USE IDENTICAL REPLACEMENT

PARTS. Repair or replace damaged cords.

/_ SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is
wider than the other). This equipment must be used with a suitable polarized 2 wire or 3
wire extension cord. Polarized connections will fit together only one way. Make sure that
the receptacle end of the extension cord has large and small blade slot widths. If the

plug does not fit fully into the extension cord, reverse the plug. If it still does not fit, obtain
a suitable extension cord. If the extension cord does not fit fully into the outlet, contact a

qualified electrician to install the proper outlet. Do not change the toot plug or extension
cord in any way.

/_ SPECIFIC SAFETY WARNING

Z_WARNING: Some dust created by this product contains chemicals known to the

State of California to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

To reduce your exposure to these chemicals, wear approved safety equipment such

as dust masks that are specially designed to filter out microscopic particles.

• arsenic and chromium from chemically treated lumber

tt O

O

O

0

Lock Button

Bouton de

verrouiltage

Boton de seguridad

G&chette

Interruptor de

Gatitlo

® 0

ASSEMBLY INSTRUCTIONS

ASSEMBLY TOOLS REQUIRED (NOT SUPPLIED):

- Phillips Screwdriver

ATTACHING BAIL HANDLE TO TRIMMER (HT012, HT018, HT020, HT022, HT512 ONLY)

The trimmer is shipped with the bail handle tied to the trimmer. To attach the bail handle:

• Cut the zip tie which holds the handle to the trimmer.

• Remove the phillips head screws from both sides of the trimmer housing or from the
carton.

• For catalog numbers (HT012, HT018, HT020, HT512}, position the handle in place by
sliding it on over the blade as shown in figure 1. Push the handle up onto the housing
and click it into place as shown in figure 2.

• Insert thephillips head screws into theopenings on both sides of the handle and tighten
securely (do not over tighten) as shown in figure 3.

• For catalog number (HT022)attach the handle and insert the threaded screw through
the handle and housing as shown in figure 4.

• Insert the two screws into the holes shown in figure 5 and screw down. Do not over
tighten.

• Screw on the plastic knob to tighten handle to unit (figure 6).

NOTE: The handle on the HT022 is adjustable to three different positions as shown

figure 7. To move handle, unscrew plastic knob, position handle as desired and
retighten knob.

Z_WARNING: DO NOT OPERATE THE HEDGE TRIMMER WITHOUTTHE BAIL HANDLE

ATTACHED.

ATTACHING EXTENSION CORD TO TRIMMER

Z_ WARNING: BE SURE HEDGE TRIMMER IS NOT LOCKED ON.

An extension cord retainer is built into the switch handle that prevents the tool from
coming unplugged. To use this feature, simply double the extension cord about 8 inches

(203 mm) from the end, and insert it into the slot in the bottom of the handle area. Hook
the loop formed by doubling the cord over the tab, as shown in figure 8. Gently tug on
the cord to insure that it is firmly retained in the trimmer's handle. Plug the receptacle
end of the extension cord into the plug blades in the trimmer (figure 8).

SAVE THESE INSTRUCTIONS FOR FUTURE USE

OPERATING INSTRUCTIONS

TO TURN THE TOOL ON

Pull the LOCK BUTTON back with your thumb and then squeeze the TRIGGER with

your fingers as shown in figure 9. (Once the toot is running you can release the LOCK

BUTTON.) To turn the toot OFF, release the TRIGGER.

TO LOCK THE TOOL ON FOR CONTINUOUS RUN

WITH THE TOOL RUNNING pull the LOCK BUTTON ALL THE WAY back, release
the TRIGGER, then release the LOCK BUTTON. The toot is now locked ON. To turn
the toot OFF, squeeze and release the TRIGGER. NOTE: In order to lock the toot on, it

is important to first release the trigger and then release the lock button.

TRIMMING INSTRUCTIONS

1. EXTENSION CORD - (Figures 8 and 10) Always keep extension cord behind
trimmer and away from the trimming operation. Never drape it over a hedge being
trimmed. If you cut or damage the cord, unplug it at the electrical outlet

immediately, before inspecting or repairing cord.

2. WORKING POSITION - ( Figure 10) Maintain proper footing and balance and do
not overreach. Wear safety goggles, non-skid footwear and rubber gloves when

trimming. Hold the toot firmly in both hands and turn the tool ON. Always hold the
trimmer, with one hand on the switch handle and one hand on the bait handle.

Never hold the toot by the blade guard.

3. TRIMMING NEW GROWTH - (Figure 11) -A wide, sweeping motion, feeding the

blade teeth through the twigs is most effective. A slight downward tilt of the blade, in
the direction of motion gives the best cutting.

z_CAUTION:Donotusethetrimmerforcuttingstemsgreaterthanitscapacity.

TR016,TR0173/8in.(5mm).

HT012,HT0185/8in.(8mm).
HT020,HT512,HT0223/4in.(19mm).

Usethetrimmeronlyforcuttingnormalshrubberyfoundaroundhousesandbuildings.

4. LEVELHEDGES(Figure12)-Toobtainexceptionallylevelhedges,apieceof

stringcanbestretchedalongthelengthofthehedgeasaguide.

5. SIDE-TRIMMINGHEDGES(Figure13)- Beginatthebottomandsweepup.

Z_WARNING;TOGUARDAGAINSTINJURY,OBSERVETHEFOLLOWING:

READINSTRUCTIONMANUALBEFOREUSING,SAVEINSTRUCTION
MANUAL.

KEEPHANDSONHANDLES.DON'TOVERREACH.
DONOTUSEUNDERWETCONDITIONS.

DONOTUSEWITHDAMAGEDEXTENSIONCORD.

• DONOTUNPLUGORSTOREWITHSWITCHLOCKEDON.
z_DANGER:KEEP HANDS AWAY FROM BLADES.

Z_CAUTION: BLADE COASTS AFTER TURN OFF.

Troubleshooting

Problem

•Unit will not start.

For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Possible Cause

• Cord not plugged in.

• Circuit fuse is blown.

• Circuit breaker
is tripped.

• Cord or switch is

damaged.

Possible Solution

• Plug in cord.

• Replace circuit fuse.

• Reset circuit breaker.

• Have cord or switch
replaced at Black & Decker

Service Center or Authorized
Servicer.

MAINTENANCE

The cutting blades are made from high quality, hardened steel and with normal usage,
they wilt not require resharpening. However, if you accidentally hit a wire fence, stones,

glass or other hard objects, you may put a nick in the blade. There is no need to remove
this nick as long as it does not interfere with the movement of the blade. If it does

interfere, unplug unit and while wearing proper eye protection use afine toothed file or

sharpening stone to remove the nick.

Ifyou drop the trimmer, carefully inspect it for damage. If the blade is bent, housing

cracked, or handles broken or if you see any other condition that may affect the
trimmer's operation, contact your local Black & Decker Service Center for repairs

before putting it back into use.

Fertilizers and other garden chemicals contain agents which greatly accelerate the
corrosion of metals. Do not store the toot on or adjacent to fertilizers or chemicals.
With the unit unplugged, use only mild soap and a damp cloth to clean the toot. Never

let any liquid get inside the toot; never immerse any part of the toot into a liquid.

Prevent the blades from rusting by applying a film of light machine oil after cleaning.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.

Accessories

/_ WARNING: DO NOT use the hedge trimmer with any type of accessory or

attachment. Such usage might be hazardous.

Service Information

Black & Decker offers a full network of company-owned and authorized service

locations throughout North America. All Black & Decker Service Centers are staffed
with trained personnel to provide customers with efficient and reliable power toot

service.
Whether you need technical advice, repair, or genuine factory replacement parts,

contact the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under

"Toots-Electric" or ca11:1-800-544-6986.

Full Two-Year Home Use Warranty, 30 Day Satisfaction Guarantee

Black & Decker warrants this product for two (2) years from date of purchase. This
warranty does not cover damage resulting from negligent handling, misuse or lack of

reasonable maintenance and care. (Proof of purchase maybe required). We wilt repair,
without charge, any defect due to faulty material or workmanship. Please return the
complete unit, transportation prepaid, to any Black & Decker/DEWALT Certified Service

Center, any Black & Decker Authorized Service Centers or DEWALT Authorized Service

Centers listed in the Yellow Pages under "Toots-Electric". These warranties do not
cover failures due to abuse, accidental damage or when repairs have been made or

attempted by other than Black & Decker and it's Authorized Service Centers. These
warranties give you specific legal rights, and you may have other rights which vary from

state to state. Should you have any questions, contact your assigned Service Center

(proof of purchase may be required).
This warranty does not apply to accessories. This warranty gives you specific legal

rights and you may have other rights which vary from state to state. Should you have

any questions, contact the manager of your nearest Black & Decker Service Center.

If you are not completely satisfied with the performance of your Black & Decker
tool, you can return it within 30 days from the date of purchase with a receipt for

a full refund (provided that the store is a participating retailer).
This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or

are missing, call 1-800-544-6986 for a free replacement.

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

See 'Tools-Electric'

- Yellow Pages -

for Service & Sales