Black & Decker SDC740B, SDC750, SDC740 User Manual
USA/Canada 1-800-231-9786
www.prodprotect.com/applica
Accessories/Parts (USA/Canada)
Accesorios/Partes (EE.UU/Canadá)
1-800-738-0245
Please Read and Save this Use and Care Book
Por favor lea este instructivo antes de usar el producto
™
†
12-CUP PROGRAMMABLE
UN DER- THE -CA BINE T
COFFEEMAKER
CAFETERA PROGRAMABLE
DE 12 TAZAS
PARA INSTALAR DEBAJO DEL GABINETE
Register your product online at www.
prodprotect.com/applica, for
a chance to WIN $100,000!
For US residents only
Registre su producto por Internet en
www.prodprotect.com/applica y tendrá la
oportunidad de GANAR $100,000!
Solamente para residentes de EE.UU
Models
Modelos
❑
SDC740
❑
SDC740B
❑
SDC750
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed, including the following:
❑
Read all instructions.
❑
Do not touch hot surfaces. Use handles or knobs.
❑
To protect against fire, electric shock and injury to persons do not
immerse cord, plugs or appliance in water or other liquid.
❑
Close supervision is necessary when any appliance is used by or near
children.
❑
Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
❑
Do not operate any appliance with a damaged cord or plug, or after the
appliance malfunctions or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination,
repair or adjustment. Or, call the appropriate toll-free number on the
cover of this manual.
❑
The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
❑
Do not use outdoors.
❑
Do not let cord hang over edge of table or counter, or touch hot
surfaces.
❑
Do not place on or near a hot gas or electric burner, or in a heated
oven.
❑
To disconnect, turn any control to OFF, then remove plug from wall
outlet.
❑
Do not use this appliance for other than intended use.
❑
Keep lid on the carafe when in use.
❑
Scalding may occur if the lid is removed during the brewing cycles.
❑
To reduce the risk of fire, do not place any heating or cooking appliance
beneath the appliance.
❑
To reduce the risk of fire, do not mount unit over or near any portion of
a heating or cooking appliance.
❑
To reduce the risk of electric shock, do not mount over a sink.
❑
To reduce the risk of fire, do not store anything directly on top of the
appliance surface when the appliance is in operation.
❑
This carafe is designed for use with this appliance. It must never be used
on a range top.
❑
Do not set a hot carafe on a cold or wet surface.
❑
Do not use a cracked carafe or a carafe having a loose or weakened
handle.
❑
Do not clean carafe with cleansers, steel wool pads, or other abrasive
material.
SAVE THESE INSTRUCTIONS.
This product is for household use only.
GROUNDED PLUG
As a safety feature, this product is equipped with a grounded plug, which will only
fit into a three-prong outlet. Do not attempt to defeat this safety feature. Improper
connection of the grounding conductor may result in the risk of electric shock. Consult a
qualified electrician if you are in doubt as to whether the outlet is properly grounded.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent
removal of the outer cover. To reduce the risk of fire or electric shock, do not
attempt to remove the outer cover. There are no user-serviceable parts inside.
Repair should be done only by authorized service personnel.
ELECTRICAL CORD
a) A short power-supply cord (or detachable power-supply cord) is to be provided
to reduce the risk resulting from becoming entangled in or tripping over a
longer cord.
b) Longer detachable power-supply cords or extension cords are available and
may be used if care is exercised in their use.
c) If a long detachable power-supply cord or extension cord is used,
1) The marked electrical rating of the detachable power-supply cord
or extension cord should be at least as great as the electrical rating of the
appliance,
2) If the appliance is of the grounded type, the extension cord should be
a grounding-type 3-wire cord, and
3) The longer cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or
tripped over.
Note: If the power supply cord is damaged, it should be replaced by qualified
personnel. In Latin America, by an authorized service center.
Product may vary slightly from what is illustrated.
. Brew basket (Part # SDC00) white, (Part # SDC00) black
. Sneak-A-Cup® interrupt feature
† . Glass carafe with lid
(Part # SDC00) white, (Part # SDC00) black
. “Keep Hot” carafe plate
† . Illuminated water reservoir with water-level markings
(Part # SDC007) white, (Part # SDC008) black
6. Reservoir lid (not shown)
7. Digital display
8. Control panel
9. Cord management hook (not shown)
0. Plug receptacle (not shown)
† . Mounting kit (Part # SDC009-0) white, (Part # SDC009-0) black
Mounting bracket (Part # SDC00) white, (Part # SDC0) black (not shown)
Note: † indicates consumer replaceable/removable parts
A
6
7
† . Mounting Parts
(Part # SDC-MOUNTING KIT)
A. 6 Spacers
½"
¼"
/6"
/6"
B. Screws
"
½"
¼"
C. Washers
. Mounting Template (in box)
You will also need:
• Tape
• Ruler (or you may cut out the ruler provided on the template)
• Electric drill with a ¼” drill bit
A
A
C
B
GETTING STARTED
• Remove all packing material, labels and any stickers.
• Remove and save literature.
• Unpack mounting parts and set them aside in a safe place where they will not
roll away or get lost.
Important: Do not attempt to operate appliance until it is properly installed.
CHOOSE A LOCATION
When choosing your location, consider the following:
• DO make sure to mount within reach of an electrical outlet.
• DO consider your normal work patterns in the kitchen when choosing
location.
• DO NOT mount over any heating or cooking appliance such as your range or
oven.
• DO NOT mount over or near a sink.
• DO NOT mount under, in front of or behind any under-cabinet light fixtures.
Note: If mounting multiple †SpaceMaker™ appliances and you are installing your
appliance next to the SpaceMaker™ oven (Fig. A.):
• Allow at least 1” between the control panel side of the oven and the appliance.
• Allow at least 4” between the side opposite the control panel of your oven and
adjacent wall or other appliance. You can mount the other appliances flush to
one another.
A.
4”
1”
4”
1”
8
9
4. Fold the template along the edge of your cabinet so the thick line is straight
with bottom front edge; pull template tight and tape down to hold in place.
5. Drilling from under the cabinet up, drill holes through the 4 places marked on
the template, using a ¼-inch drill bit (E).
Important: Always ensure you are drilling straight up through the marked
mounting hole on the template. Drilling at an angle may prevent proper
installation and may damage cabinets if the drill bit pierces the partition.
6. Once holes are drilled, remove tape and mounting template.
7. Wipe dust and debris off the topside and underside of the cabinet surface.
8. Place a washer inside the cabinet over each of the 4 holes you drilled.
Important: Top panel of coffeemaker is removable to make installation easier.
Simply grip the panel at the rear and pull back to remove (Fa) or insert a flathead
screwdriver at the front of the panel by one of the mounting holes and twist to
pop open (Fb). Once removed, mount panel in place following the directions
below and then slide coffeemaker back on the panel track to reattach appliance
once the panel has been mounted.
9. Hold panel in place; drilled holes on cabinet should be aligned with mounting
holes on the panel.
10. From inside of the cabinet down into panel holes, drop 4 screws in place.
Place a nut on each screw and tighten.
Note: To determine which screws to use, you must have enough of the screw
exposed underneath the cabinet to properly thread the screw into the nut.
Note: Always tighten nuts to ensure the appliance does not move or shake during
operation.
Caution: This appliance features a Save-A-Plug™ outlet receptacle to connect
smaller †SpaceMaker™ appliances such as the mini food processor / grinder or
can opener. Do not use this outlet for any other appliance!
Caution: When selecting a location for your coffeemaker, make sure you have
adequate room to reach the receptacle.
Note: If you are connecting another †SpaceMaker™ appliance into the Save-A-
Plug™ outlet, make sure you can easily unplug the appliance after each use.
DETERMINE CABINET TYPE
Prior to installation, determine if your cabinet has a flat bottom (B) or
an overhanging molding (C). If your cabinet is flat, follow STANDARD
INSTALLATION; if the cabinet has an overhang molding, refer to OVERHANG
MOLDING INSTALLATION.
STANDARD INSTALLATION (FLAT CABINET)
Important: Always wear protective glasses or goggles to prevent injury when
drilling.
1. Clear countertop under installation area to avoid getting dust or debris on other
appliances or items. Open cabinets and remove contents to make mounting
easier.
2. Clean both the underside and topside of the bottom panel of the cabinet.
3. With cabinet doors open, place mounting template flush against the surface of
the underside of your cabinet, making sure to align thick line on template with
bottom front edge of your cabinet (D).
Important: Do not align screw holes on template directly under the partition
between cabinets, as this will prevent you from installing the appliance properly.
Pay close attention to where the drill holes will be set so as not to damage your
cabinets during mounting. Drilling through your cabinet’s partition may cause
damage to cabinets and prevent proper installation.
D
E
B
C
Fa Fb
0
4. After measuring the overhang molding thickness as shown in Illustration
H, look at the dashed lines on the mounting template; each line has a
measurement next to it that indicates the thickness of the overhang molding
used with that line. For example, if your cabinet has an overhang molding
thickness of ½”, you will use the ½” dashed line on the template.
5. Fold the template along the dashed line that matches the thickness of your
overhang molding.
6. Place the folded template against the back edge of the overhang molding,
making sure the side with the drill hole marks is facing down (J).
Important: Do not align screw holes on template directly under the partition
between cabinets, as this will prevent you from installing the appliance properly.
Pay close attention to where the drill holes will be set so as not to damage your
cabinets during mounting. Drilling through your cabinet’s partition may cause
damage to cabinets and prevent proper installation.
7. Making sure to keep the fold line straight against the back edge of the overhang
molding, tape the template securely in place.
8. Drilling from under the cabinet up, drill holes through the 4 places marked on
the template using a ¼-inch drill bit (K).
Important: Always ensure you are drilling straight up through the marked
mounting hole on the template. Drilling at an angle may prevent proper
installation and may damage cabinets if the drill bit pierces the partition.
9. Once holes are drilled, remove tape and mounting template.
10. Wipe dust and debris off underside and topside of cabinet surface.
11. Once the panel is secure, reattach coffeemaker to panel by lifting appliance
up, aligning it with the track on the panel and then sliding it back into place.
12. Plug into standard electrical outlet. Extra cord can be hung over cord
management hook behind unit (G).
Caution: This appliance features a Save-A-Plug™ outlet receptacle to connect
smaller †SpaceMaker™ appliances such as the mini food processor / grinder or
can opener. Do not use this outlet for any other appliance!
Note: If you are connecting another †SpaceMaker™ appliance into the
Save-A-Plug™ outlet, make sure you can easily unplug the appliance after
each use.
13. Your †SpaceMaker™ appliance is now ready for use!
OVERHANG MOLDING INSTALLATION
For cabinets with an overhang molding (see Illustration C)
Important: Always wear protective glasses or goggles to prevent injury when
drilling.
Note: Spacers are provided in case your cabinet has an overhang molding at the
front edge. Only use spacers on the rear screws of the appliance to ensure it is
level with the front.
1. Clear countertop under installation area to avoid getting on other appliances or
items. Open cabinets and remove contents to make mounting easier.
2. Clean both the underside and topside of the bottom panel of the cabinet.
3. Using a ruler, measure the thickness of the overhang molding (H), accurately
noting the number for use in the following step.
Note: If you do not have a ruler, you may use the paper ruler provided on the
edge of your mounting template.
J
H
G
K
11. Place a washer inside the cabinet over each of the 4 holes you drilled.
12. Now, use your ruler or the paper ruler provided to measure the overhang
molding height, placing your ruler vertically against the underside of the
cabinet behind the overhang molding. This number determines the number of
spacers you need, using a number of spacers equal to the overhang molding
height. For example, a 1” overhang molding would use 2, ½” spacers on each
of the rear holes (L).
13. Drop one of your screws through each of the washers covering the holes in the
cabinet, from inside the cabinet down.
Note: To determine which screws to use, you must have enough of the screw
exposed underneath the cabinet to properly thread the screw into the nut.
14. Place the appropriate number of spacers determined in step 12 on both of the
rear screws so the appliance will be even (M).
Note: If the height of your overhang molding is too tall to be accommodated by
the number of spacers provided, you may call, toll-free, at 1-800-231-9786 to
order additional spacers at no charge.
Note: For spacer installation, you may require assistance (in mounting) in order to
hold spacers in place while securing the appliance at the same time. If assistance
is not available, use a small clamp to hold the spacers in place while you position
the appliance.
Important: Top panel of coffeemaker is removable to make installation easier.
Simply grip the panel at the rear and pull back to remove (see Illustration Fa)
or insert a flathead screwdriver at the front of the panel by one of the mounting
holes and twist to pop open (see Illustration Fb). Once removed, mount in place
following the directions below and then slide coffeemaker back on the panel
track to reattach appliance once the panel has been mounted.
M
L
15. Once spacers are set, hold panel up and tighten nuts onto each of the screws
to secure.
Note: Always tighten nuts to ensure the appliance does not move or shake during
operation.
16. Once the panel is secure, reattach coffeemaker to panel by lifting appliance
up, aligning it with the track on the panel and then sliding it back into place.
17. Plug into standard electrical outlet. Extra cord can be hung over cord
management hook behind unit (see Illustration G).
Caution: This appliance features a Save-A-Plug™ outlet receptacle to connect
smaller †SpaceMaker™ appliances such as the mini food processor / grinder or
can opener. Do not use this outlet for any other appliance!
Note: If you are connecting another †SpaceMaker™ appliance into the Save-A-
Plug™ outlet, make sure you can easily unplug the appliance after each use.
18. Your †SpaceMaker™ appliance is now ready for use!
Loading...