Black & Decker RS500, 612872-00 User Manual

General Safety Rules

WARNING: Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Use in well ventilated areas only.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

• Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply system.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious

personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents cover moving parts and should be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off.Any tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

Service

• Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

Specific Safety Rules

• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

• Keep hands away from cutting area. Never reach underneath the material for any reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers or thumb into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the saw by gripping the shoe.

• Keep blades sharp. Dull blades may cause the saw to swerve or stall under pressure.

• Use extra caution when cutting overhead and pay particular attention to overhead wires

which may be hidden from view. Anticipate the path of falling branches and debris ahead of time.

• When cutting pipe or conduit ensure that they are free from water, electrical wiring, etc.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

The label on your tool may include the following symbols.

V..............volts

A..............amperes

Hz............hertz

W ............watts

min ..........minutes

............alternating current

........direct current

no............no load speed

............Class II Construction

SPM ........strokes per minute

............earthing terminal

............safety alert symbol

INSTRUCTION MANUAL

Cat. No. RS500

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

AAAARRRRIIIIAAAABBBBLLLLEE

PPPPEEEEEEEEDD

EEEECCCCIIIIPPPPRRRROOOOCCCCAAAATTTTIIIINNNNGG

AAAAWW

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-544-6986

BEFORE YOU CALL, HA VE THE FOLLOWING INFORMATION AVAILABLE, CAT ALOG No.,

TYPE No., AND DATE CODE (e.g. 0130M). IN MOSTCASES, ABLACK & DECKER REPRE-

SENTATIVE CAN RESOL VE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGES-

TION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VIT ALTO BLACK & DECKER.

TRIGGER SWITCH

USE OF EXTENSION CORDS

Make sure the extension cord is in good condition before using. Always use the proper size extension cords with the tool – that is, proper wire size for various lengths of cord and heavy enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in line voltage resulting in loss of power and overheating. For proper size cords see chart below.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage Than Than 0-6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended

"Tools–Electric" in the yellow pages of the phone directory. This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABELREPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

No de cat. RS500

MOTOR

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. Arating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black& Decker tools are factory-tested; if this tool does not operate, check the power supply.

SAVE THESE INSTRUCTIONS

OPERATION

CAUTION: Always wear eye protection while operating this power tool.

NOTE: Before cutting any type of material, be sure it is firmly anchored or clamped to pre-

vent slipping.

• Place blade lightly against work to be cut.

• Switch on saw motor before applying pressure.

• Always hold saw firmly with both hands while cutting as shown in Figure 1. Whenever possible, the saw shoe must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage.

VARIABLE SPEED SWITCH (FIGURE 2)

The variable speed trigger switch will give you added versatility. The further the trigger is depressed the higher the speed of the saw. To turn the tool “OFF” release the trigger. NOTE: This tool has no provision to lock the switch in the ON position, and should never be locked in the ON position by any other means.

BLADE CLAMP RELEASE LEVER (FIGURE 3)

CAUTION: TURN OFF AND UNPLUG FROM POWER SUPPLY WHEN CHANGING

BLADES.

T o install blade into saw:

1. Lift the blade clamp release lever to its full open position as shown in Figure 3.

2. Insert blade shank from the front locating hole in blade over pin on reciprocating shaft.

3. Close blade clamp release lever.

4. Check to ensure blade is secure before cutting.

T o remove blade from saw:

1. Open blade clamp release lever to its full open position.

2. Remove blade.

FLUSH CUTTING (FIGURE 4)

• The compact design of the reciprocating saw motor housing and pivoting shoe permit close cutting to floors, corners and other difficult areas.

• To maximize flush cutting capabilities, insert the blade shaft into the blade clamp with the teeth of the blade facing up.

• Turn the saw upside down so you are as close to the work surface as possible.

METAL CUTTING (FIGURE 5)

• Use a finer blade for ferrous metals and a coarse blade for non-ferrous materials.

• In thin gauge sheet metals it is best to clamp wood to both sides of sheet. This will ensure a clean cut without excess vibration or tearing of metal.

• Avoid forcing cutting blade as this reduces blade life and causes costly blade breakage.

NOTE: Spread a thin film of oil or other coolant along the line ahead of the saw cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

POCKET CUTTING - WOOD ONLY (FIGURE 6)

• Measure the surface area to be cut and mark clearly with a pencil, chalk or scriber.

• Insert blade in blade clamp and tighten blade clamp securely.

• Tip the saw backward until the back edge of the shoe is resting on the work surface and the moving blade will clear the surface.

• Switch motor on, permitting blade to obtain maximum speed.

• Grip handle steadily and begin a slow, deliberate upward swing with the handle of the saw.

• The blade will begin to feed into material. Always be sure blade is completely through material before continuing with pocket cut.

NOTE: In areas where blade visibility is limited, use the edge of the shoe as a guide.

PROJECT TIPS

• Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while cutting.

• When cutting, always ensure that the shoe is resting firmly against the workpiece. This will improve operator control and minimize vibration.

• For longer blade life, use bi-metal blades. These utilize a carbon steel back welded to high speed steel teeth making the blade more flexible and less prone to breaking.

MAINTENANCE

UNPLUG SAW AND REMOVE ACCESSORY WHEN PERFORMING ANY CLEANING OR OTHER MAINTENANCE. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust etc.

• When electric tools are used on fiberglass boats, sports cars, drywall etc.,they are subject to accelerated wear and possible premature failure, as the fiberglass chips and grindings and drywall dust are highly abrasive to bearings, brushes, commutator, etc. During any use on fiberglass or drywall it is extremely important that the tool be cleaned frequently by blowing with an air jet.

LUBRICATION

Your saw was properly lubricated before leaving the factory. Once every year take or send your saw to a Black & Decker service center, or authorized service station, for a complete cleaning, inspection and lubrication. Tools "out of service" for long periods should be relubricated before being put back to work.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts

ACCESSORIES

BLADES

The RS500 Reciprocating Saw will accept up to a 12 inch long blade. Always use the shortest blade suitable for your project but long enough to keep the blade cutting through the material. Longer blades are more likely to be bent or damaged during use. During operation some longer blades may vibrate or shake if the saw is not kept in contact with the workpiece.

Recommended accessories for use with your saw are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986.

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

GUIDE TECHNIQUE

SSSSCCCCIIIIEEEE AAAALLLLTTTTEEEERRRRNNNNAAAATTTTIIIIVVVVEEEE ÀÀÀÀ VVVVIIIITTTTEEEESSSSSSSSEEEE VVVVAAAARRRRIIIIAAAABBBBLLLLEE

AAAAVVVVAAAANNNNTTTT DDDDEEEE RRRREEEETTTTOOOOUUUURRRRNNNNEEEERRRR LLLLEEEE PPPPRRRROOOODDDDUUUUIIIITT

PPPPOOOOUUUURRRR QQQQUUUUEEEELLLLQQQQUUUUEEEE RRRRAAAAIIIISSSSOOOONNNN QQQQUUUUEEEE CCCCEEEE SSSSOOOOIIIITTTT,,,,

CCCCOOOOMMMMPPPPOOOOSSSSEEEERRRR LLLLEE

1111 888800000000 555544444444----66669999888866

Règles générales de sécurité

AVERTISSEMENT – Lire attentivement et comprendre toutes les instructions. Toute omission à l’égard des instructions énumérées ci-dessous pourrait entraîner un choc électrique, un incendie et de graves blessures corporelles.

CONSERVER LES PRÉSENTES INSTRUCTIONS

Zone de travail

• Garder la zone de travail propre et bien éclairée. Un établi encombré et une zone

sombre sont sources d’accidents.

• Ne pas utiliser un outil électrique dans une atmosphère explosive, notamment en

présence de liquides, de gaz ou de poussière inflammables. Un outil électrique produit

des étincelles qui peuvent enflammer la poussière et les émanations. Ne l’utiliser que dans un endroit bien ventilé.

• Tenir éloignés les spectateurs, les enfants et les visiteurs pendant qu’un outil

électrique est en marche. Toute distraction peut être cause de perte de contrôle.

Sécurité en électricité

• Un outil à double isolement est muni d’une fiche polarisée, une lame étant plus large

que l’autre. Cette fiche ne s’insère que d’une seule façon dans une prise polarisée. Inverser la fiche si elle ne s’insère pas complètement dans la prise. Si elle ne pénètre toujours pas dans la prise, faire appel à un électricien pour installer une prise polarisée. Ne remplacer en aucun cas la fiche. Le double isolement élimine le besoin

d’un cordon électrique à trois conducteurs avec mise à la terre et celui d’un système d’alimentation électrique à mise à la terre.

• Éviter tout contact du corps avec les surfaces mises à terre, notamment tuyaux,

radiateurs, cuisinières, réfrigérateurs. Le risque d’électrocution est encore plus grand si

le corps de l’utilisateur est mis à la terre.

• Ne pas exposer les outils électriques à la pluie ou à des conditions humides. L’eau

qui pénètre dans un outil électrique accroît le risque d’électrocution.

• Ne pas faire un usage abusif du cordon électrique. Ne jamais utiliser le cordon pour

transporter l’outil ou pour retirer la fiche de la prise. Tenir le cordon loin de la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Remplacer immédiatement un cordon endommagé. Un cordon endommagé accroît le risque

d’électrocution.

• Lorsqu’un outil électrique est utilisé à l’extérieur, y brancher une rallonge d’extérieur

marquée « W-A » ou « W ». Ce type de cordon est prévu pour un usage extérieur et réduit

le risque d’électrocution.

Sécurité personnelle

• Demeurer vigilant, regarder ce que l’on fait et user de discernement lorsqu’un outil

électrique est en marche. Ne jamais utiliser un outil lorsqu’on est fatigué ou sous l’influence de drogues, d’alcool ou de médicaments. Un moment d’inattention pendant

qu’un outil électrique est en marche peut entraîner de graves blessures corporelles.

• Se vêtir adéquatement. Ne pas porter des vêtements amples ou des bijoux. Retenir

les cheveux longs. Tenir ses cheveux, ses vêtements et ses gants loin des pièces mobiles. Les vêtements amples, les bijoux et les cheveux longs peuvent être pris dans les

pièces mobiles. Les évents couvrent des pièces mobiles et doivent être évités.

• Éviter tout démarrage accidentel. S’assurer que l’interrupteur est à l’arrêt avant de

brancher l’outil. Afin d’éviter les accidents, ne pas transporter un outil électrique en ayant

le doigt sur l’interrupteur, ni ne brancher l’outil dont l’interrupteur est en position de marche.

• Retirer les clés de réglage avant de mettre l’outil en marche. Une clé laissée attachée à

une pièce en rotation de l’outil peut entraîner des blessures corporelles.

• Ne pas tendre le bras trop loin. En tout temps, avoir une bonne prise de pied au sol et

se tenir bien en équilibre. Une bonne prise de pied et un bon équilibre permettent un

meilleur contrôle de l’outil dans les situations imprévues.

• Utiliser un équipement de sécurité. Toujours porter un protecteur oculaire. Un

masque antipoussières, des chaussures de sécurité à semelle antidérapante, un casque ou des protecteurs auditifs doivent être portés selon les circonstances.

Utilisation et entretien de l’outil

• Utiliser des brides de serrage ou tout autre moyen pratique pour soutenir et

assujettir la pièce à travailler sur une plate-forme stable. La pièce à travailler tenue en

main ou contre son corps est instable et peut engendrer une perte de contrôle.

• Ne pas forcer l’outil. Utiliser le bon outil pour la bonne application. Le bon outil fera le

travail mieux et de façon plus sécuritaire à la vitesse pour laquelle il a été conçu.

• Ne pas utiliser l’outil si l’interrupteur ne peut le mettre en marche ni l’arrêter. Un outil

qui ne peut être contrôlé à l’aide de l’interrupteur est dangereux et doit être réparé.

• Débrancher la fiche de la source d'alimentation avant de procéder à des réglages, de

changer les accessoires ou de ranger l’outil. Ces mesures de sécurité préventives

réduisent le risque de mise en marche accidentelle de l’outil.

• Ranger l’outil tournant au ralenti hors de portée des enfants et des personnes

inexpérimentées. Les outils sont dangereux entre les mains d’utilisateurs inexpérimentés.

• Manipuler l’outil avec soin. Conserver les outils de coupe affûtés et propres. Un outil

bien entretenu, dont les bords de coupe sont bien aiguisés, est moins susceptible de gripper et plus facile à contrôler.

• Vérifier si les pièces mobiles sont bien alignées et ne grippent pas, si des pièces ne

sont pas brisées et si l’outil ne présente pas toute autre condition susceptible de nuire à son bon fonctionnement. Si l’outil est endommagé, le faire réparer avant de l’utiliser.De nombreux accidents sont dus à des outils mal entretenus.

• N’utiliser que les accessoires recommandés par le fabricant du modèle en question.

Les accessoires qui peuvent convenir à un outil, peuvent devenir dangereux lorsqu’ils sont utilisés avec un autre outil.

Entretien

• L’entretien de l’outil ne doit être effectué que par un réparateur qualifié. L’entretien et

la maintenance effectués par un personnel non qualifié pourraient engendrer des blessures.

• Lors de l’entretien de l’outil, n’utiliser que des pièces de rechange identiques. Suivre

les instructions de la section Maintenance du présent guide. L ’utilisation de pièces non

autorisées ou l’omission de se conformer aux instructions de maintenance peuvent créer un risque de choc électrique et des blessures.

+ 3 hidden pages