Black & Decker LHT120 User Manual
20V MAX* LITHIUM HEDGE TRIMMER -
INSTRUCTION MANUAL
Model Number LHT120
ThankyouforchoosingBlack & Decker!Go
to www.BlackandDecker.com/NewOwner
to register your new product.
PLEASE READ BEFORE RETURNING
THIS PRODUCT FOR ANY REASON:
If you have a question or experience a problem with your
Black & Decker purchase, go to
WWW.BLACKANDDECKER.COM/INSTANTANSWERS
for instant answers 24 hours a day.
If you canʼt find the answer or do not have access to the internet,
call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri
to speak with an agent.
Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZADE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
Model Number LHT120
*Maximum initial battery pack voltage
(measured without a workload) is 20
volts. Measured under a workload,
nominal voltage is 18.
1
TABLE OF CONTENTS
Safety Guidelines - Definitions.................................................2
Important Safety Rules ............................................................2
Components.............................................................................4
Important Safety Instructions for Battery Chargers..................5
Important Safety Instructions for Battery Packs.......................6
Charging Procedure.................................................................7
Installing/Removing Battery Pack ............................................8
Operation .................................................................................8
Maintenance ............................................................................9
Accessories..............................................................................10
Service Information ..................................................................10
Full Two-Year Home Use Warranty..........................................10
Troubleshooting .......................................................................11
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The
information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help
you recognize this information.
DANGER: Indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result in
property damage.
IMPORTANT SAFETY WARNINGS
AND INSTRUCTIONS
TO REDUCE RISK OF INJURY:
• Read all instructions before operating product. Failure to follow all
instructions listed below may result in electric shock, fire and or
serious injury.
• Save these instructions and review frequently prior to use and in
instructing others.
• Keep long hair and loose clothing away from openings and moving
parts.
WARNING: When using electric gardening
appliances, basic safety precautions should always be followed to
reduce risk of fire, electric shock, and personal injury, including the
following.
GENERAL SAFETY WARNINGS AND
INSTRUCTIONS FOR ALL TOOLS
• READ and understand all instructions.
• ABATTERY OPERATED UNIT with integral batteries or a separate
battery pack must be recharged only with the specified charger for
the battery. A charger that may be suitable for one type of battery
may create a risk of fire when used with another battery.
• USE BATTERY OPERATED UNIT ONLY with specifically
designated battery pack. Use of any other batteries may create a
risk of fire.
• AVOID accidental starting. Be sure switch is in the locked or off
position before inserting battery pack. Carrying units with your
finger on the switch or inserting the battery pack into a unit with the
switch on invites accidents.
• DO NOT use unit if switch does not turn it on or off. A unit that
cannot be controlled with the switch is dangerous and must be
repaired.
2
• DISCONNECT battery pack from unit or place the switch in the
locked or off position before making any adjustments, changing
accessories, or storing the unit. Such preventative safety
measures reduce the risk of starting the unit accidentally.
• AVOID DANGEROUS ENVIRONMENT - Do not use or charge
hedge trimmers in damp or wet locations.
• DO NOT USE OR CHARGE battery operated hedge trimmer in
rain.
• DO NOT OPERATE hedge trimmer in gaseous or explosive
atmospheres. Motors in these tools normally spark, and the sparks
might ignite fumes.
• KEEP CHILDREN AWAY - All visitors should be kept at a safe
distance from the work area.
• DRESS PROPERLY - Donʼt wear loose clothing or jewelry. They
can be caught in moving parts. Use of rubber gloves and
substantial footwear is recommended when working outdoors.
Wear protective hair covering to contain long hair.
• ALWAYS WEAR EYE PROTECTION – Wear safety glasses or
goggles at all times when this unit is in use. Also use face or dust
mask. Safety glasses are available at extracostat your local Black &
Decker Service Center orauthorized service facility.
• USE RIGHT APPLIANCE - Do not use appliance for any job except
that for which it is intended.
• AVOID UNINTENTIONAL STARTING - Donʼt carry hedge trimmer
with finger on switch.
DANGER: Risk of cut. Keep hands away from
blades. Keep both hands on handles when power is on.
• DO NOT ATTEMPT to remove cut material or hold material to be cut
when blades are moving. Make sure battery is removed when
clearing jammed material from blades. Do not grasp the exposed
cutting blades or cutting edges when picking up or holding the
hedge trimmer.
CAUTION: Blades may coast after turn off.
CAUTION: NEVER use guard as a handle. Never
grasp the unit by the guard. Failure to heed this warning can result
in serious personal injury.
•
DONʼT FORCE HEDGE TRIMMER - It will do the job better and with less
likelihood of a risk of injury at the rate for which it was designed.
DANGER: If blade jams on any electrical cord or line,
DO NOT TOUCH THE BLADE! IT CAN BECOME ELECTRICALLY
LIVE AND VERY DANGEROUS. Release the unit in the safest
manner possible. Disconnect the damaged electrical cord or line
from the power source. If possible, do so safely. If in doubt, call an
electrician or the electrical contractor for assistance. Failure to
heed this Danger will result in serious personal injury and possibly
death.
• DONʼT OVERREACH - Keep proper footing and balance at all
times.
• STAY ALERT - Watch what you are doing. Use common sense. Do
not operate hedge trimmer whenyou are tired.
• STORE IDLE HEDGE TRIMMER INDOORS - When not in use,
hedge trimmer should be stored indoors in a dry and high or
locked-up place–out of reach of children.
• MAINTAIN HEDGETRIMMERWITH CARE-Keep cuttingedge sharp
and clean forbest performance and to reduce the riskofinjury.Follow
instructions forlubricating. Keep handles dry,clean andfree from oil and
grease.
CAUTION: Do not at any time let brake fluids,
gasoline, petroleum based products, penetrating oils, etc., come in
contact with plastic parts. They contain chemicals that can damage,
weaken or destroy plastic.
• CHECK DAMAGED PARTS - If damage to trimmer occurs, before
further use of the hedge trimmer, a guard or other part that is
damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of
3
parts, mounting and any other condition that may affect its
operation. A guard or other part that is damaged should be properly
repaired or replaced by an authorized service center unless otherwise
indicated elsewhere in this manual.
• REMOVE BATTERY before servicing, cleaning or removing
material from the hedge trimmer. Remove battery from your hedge
trimmer and carry by the front handle when not in use.
• EXERCISE CARE in handling batteries in order not to short the
battery with conducting materials such as rings, bracelets and
keys. The battery or conductor may overheat and cause burns.
• DO NOT OPEN OR MUTILATE the batteries. Released
electrolyte is corrosive and may cause damage to the eyes or skin.
It may be toxic if swallowed.
• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be used for the
hedge trimmer. Receptacles are available having built-in GFCI
protection and may be used for this measure of safety.
WARNING: To reduce the risk of electrical shock;
do not expose to rain, do not use on wet surfaces. Store indoors.
SAVE THESE INSTRUCTIONS
SPECIFIC SAFETY RULES
• Hold tool by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
To reduce your exposure to these chemicals, wear approved safety
equipment such as dust masks that are specially designed to filter
out microscopic particles.
The label on your tool may include the following symbols.
V................volts A ....................amperes
Hz..............hertz W ..................watts
min ............minutes ..................alternating current
• arsenic and chromium from chemically treated lumber
..........direct current
..............
............safety alert symbol .../min ............strokes
Class II Construction
n
o ..................no load speed
....................earthing terminal
per minute
COMPONENTS
1. Trigger Switch
2. Lock Button
3. Switch Hnadle
4. Blade Guard
5. Bail Handle
6. Charger
7. Battery
8. Blade
9. Blade Sheath
2
5
4
8
9
3
1
WARNING: Some dust created by this product
contains chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm. Some examples of these
chemicals are:
• compounds in fertilizers
• compounds in insecticides, herbicides and pesticides
7
6
4
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGERS
SAVE THESE INSTRUCTIONS: This manual contains important
safety instructions for battery chargers.
• Before using charger, read all instructions and cautionary markings
on charger, battery pack, and product using battery pack.
WARNING: Shock hazard. Do not allow any liquid
to get inside charger.
CAUTION:Burn hazard. To reduce the risk of injury,
charge only designated Black & Decker batteries. Other types of
batteries may burst causing personal injury and damage.
CAUTION: Under certain conditions, with the
charger plugged in to the power supply, the charger can be shorted
by foreign material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from charger cavities. Always
unplug the charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to clean.
• The charger supplied with this product is intended to be
plugged in such that it is correctly orientated in a vertical or
floor mount position.
• DO NOT attempt to charge the battery pack with any chargers
other than the ones in this manual. The charger and battery
pack are specifically designed to work together.
• These chargers are not intended for any uses other than
charging designated Black & Decker rechargeable batteries.
Any other uses may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting charger.
This will reduce risk of damage to electric plug and cord.
• Make sure that cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary.
Use of improper extension cord could result in risk of fire, electric
shock, or electrocution.
• An extension cord must have adequate wire size (AWG or
American Wire Gauge) for safety. The smaller the gauge number
of the wire, the greater the capacity of the cable, that is 16 gauge
has more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each individual
extension contains at least the minimum wire size.
Recommended Minimum Wire Size for Extension Cords
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gauge
Than Than
0-6 18 16 16 14
6-10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
• Do not place any object on top of charger or place the charger
on a soft surface that might block the ventilation slots and
result in excessive internal heat. Place the charger in a position
away from any heat source. The charger is ventilated through
slots in the top and the bottom of the housing.
• Do not mount charger on wall or permanently affix charger to
any surface. The charger is intended to use on a flat, stable surface
(i.e., table top, bench top).
• Do not operate charger with damaged cord or plug — have
them replaced immediately.
• Do not operate charger if it has received a sharp blow, been
dropped, or otherwise damaged in any way. Take it to an
authorized service center.
• Do not disassemble charger; take it to an authorized service
center when service or repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or fire.
5
Minimum Gauge for Cord Sets
• Disconnect the charger from the outlet before attempting any
cleaning. This will reduce the risk of electric shock. Removing the
battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard household
electrical power (120 Volts). Do not attempt to use it on any
other voltage.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY WARNINGS
FOR BATTERY PACKS
WARNING: For safe operation, read this manual
and manuals originally supplied with tool before using the charger.
The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below.
Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
battery packs are burned.
• Do not charge or use battery in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust.
Inserting or removing the battery from the charger may ignite the
dust or fumes.
• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If battery liquid
gets into the eye, rinse water over the open eye for 15 minutes or
until irritation ceases. If medical attention is needed, the battery
electrolyte for Li-ion batteries is composed of a mixture of liquid
organic carbonates and lithium salts.
• Contents of opened battery cells maycause respiratory irritation.
Provide fresh air. If symptoms persist, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
• Charge the battery packs only in Black & Decker chargers.
• DO NOT splash or immerse in water or other liquids. This may
cause premature cell failure.
• Do not store or use the tool and battery pack in locations
where the temperature may reach or exceed 105°F (40˚C) (such
as outside sheds or metal buildings in summer).
WARNING: Never attempt to open the battery pack
for any reason. If battery pack case is cracked or damaged, do not
insert into charger. Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has received a sharp blow,
been dropped, run over or damaged in any way (i.e., pierced with a
nail, hit with a hammer, stepped on). Damaged battery packs should
be returned to service center for recycling.
WARNING: Fire hazard. Do not store or carry
battery so that metal objects can contact exposed battery
terminals. For example, do not place battery in aprons, pockets, tool
boxes, product kit boxes, drawers, etc., with loose nails, screws,
keys, etc. Transporting batteries can possibly cause fires if the
battery terminals inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like. The US
Department of Transportation Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in commerce or on airplanes
(i.e., packed in suitcases and carry-on luggage) UNLESS they are
properly protected from short circuits. So when transporting individual
batteries, make sure that the battery terminals are protected and well
insulated from materials that could contact them and cause a short
circuit. NOTE: LI-ION batteries should not be put in checked
baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away from
direct sunlight and excess heat or cold.
2. Long storage will not harm the battery pack or charger.
6
CHARGING PROCEDURE
The standard charger provided will charge a fully depleted battery in
about 8 hours.
1. Plug the charger into an appropriate outlet before inserting the
battery pack.
2. Insert the battery pack into the
charger as shown in figure 1.
3. The green LED will flash
indicating that the battery is
being charged.
4. The completion of
charge is indicated by the
green LED remaining on
continuously. The pack is
fully charged and may be
used at this time or left on
the charger.
Recharge discharged batteries as soon as possible after use or
battery life may be greatly diminished. It is recommended that the
batteries be recharged after each use.
CHARGER DIAGNOSTICS
This charger is designed to detect certain problems that can arise
with the battery packs or the power source. Problems are indicated
by one LED flashing in different patterns.
BAD BATTERY
The charger can detect a weak or damaged battery. The red
LED flashes in the pattern indicated on the label. If you see
this bad battery blink pattern, do not continue to charge the
battery. Return it to a service center or a collection site for
recycling.
HOT/COLD PACK DELAY
When the charger detects a battery that is excessively hot or
excessively cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has normalized.
1
After this happens, the charger automatically switches to the Pack
Charging mode. This feature ensures maximum battery life. The red
LED flashes in the pattern indicated on the label when the hot / cold
pack delay is detected.
LEAVING THE BATTERY IN THE CHARGER
The charger and battery pack can be left connected with the green
LED glowing indefinitely. The charger will keep the battery pack
fresh and fully charged.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the battery
pack is charged when the air temperature is between 60°F and
80°F (16°- 27°C). DO NOT charge the battery pack in an air
temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).
This is important and will prevent serious damage to the battery
pack.
2. The charger and battery pack may become warm to touch while
charging. This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the battery pack after use, avoid
placing the charger or battery pack in a warm environment such as
in a metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other
appliance
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
c. Move charger and battery pack to a location where the
surrounding air temperature is approximately 60°F and 80°F
(16°- 27°C)
d. If charging problems persist, take the tool, battery pack and
charger to your local service center.
4. The battery pack should be recharged when it fails to produce
sufficient power on jobs which were easily done previously. DO
NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack
whenever you desire with no adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not limited
7
to, steel wool, aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery pack in the
cavity. Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING: Shock hazard. Do not allow any liquid
to get inside charger. Never attempt to open the battery pack for any
reason. If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
INSTALLING / REMOVING BATTERY PACK
OPERATION
SWITCH
To turn the unit “ON”, slide the lock off button,
shown in figure 3, forward and, squeeze the
trigger switch. Once the unit is running, you
may release the lock off button. In order to
keep the unit running you must continue to
squeeze the trigger. To turn the unit “OFF”,
release the trigger.
3
WARNING: Make certain the lock-off button is
engaged to prevent switch actuation before removing or installing
battery.
TO INSTALL BATTERY PACK:
Insert battery pack into tool until an
audible click is heard (figure 2).
TO REMOVE BATTERY PACK:
Depress the battery release button in
the back of the battery pack and pull
battery pack out of tool (figure 2).
2
WARNING: Never attempt to
lock a switch in the ON position.
TRIMMING INSTRUCTIONS
1. WORKING POSITION – Maintain proper
footing and balance and do not
overreach. Wear safety goggles, nonskid footwear and rubber gloves when
trimming. Hold the unit firmly in both
hands and turn the unit ON. Always hold
the trimmer, as shown in the illustrations
in this manual, with one hand on the
switch handle and one hand on the bail
handle. (figure 4) Never hold the unit by
the blade guard.
8
4
2. TRIMMING NEW GROWTH – (Figure
5) A wide, sweeping motion, feeding the
blade teeth through the twigs is most
effective. A slight downward tilt of the
blade, in the direction of motion gives the
best cutting.
CAUTION: Do not cut
stems greater than 3/4 inch (19mm). Use
the trimmer only for cutting normal
shrubbery around houses and buildings.
3. LEVEL HEDGES (Figure 6) – To obtain
exceptionally level hedges a piece of
string can be stretched along the length
of the hedge as a guide.
4. SIDE TRIMMING HEDGES (Figure 7) –
Hold the trimmer as shown and begin at
the bottom and sweep up.
WARNING: TO GUARD
AGAINST INJURY, OBSERVE THE
FOLLOWING:
• READ INSTRUCTION MANUAL
BEFORE USING.
• SAVE INSTRUCTION MANUAL.
• KEEP HANDS AWAY FROM BLADES.
• KEEP HANDS ON HANDLES. DONʼT
OVERREACH.
CAUTION: BLADE MAY
COAST AFTER TURN OFF.
• DO NOT USE UNDER WET CONDITIONS.
5
A vinyl sheath is supplied with your
trimmer for storing. Slip the hedge
trimmer into it, as shown in figure 8.
MAINTENANCE
8
WARNING: Remove
battery pack before servicing, cleaning
or removing material fromthe
gardening appliance.
6
7
The cutting blades are made from
high quality, hardened steel and with
normal usage, they will not require
resharpening. However, if you
accidentally hit a wire fence (figure 9),
stones, glass or other hard objects,
you may put a nick in the blade. There
is no need to remove this nick as long
as it does not interfere with the
movement of the blade. If it does
interfere, remove the battery and use a fine toothed file or sharpening
stone to remove the nick. If you drop the trimmer, carefully inspect it for
damage. If the blade is bent, housing cracked, or handles broken or if
you see any other condition that may affect the trimmerʼs operation
contact your local Black & Decker Service Center for repairs before
putting it back into use.
Fertilizers and other garden chemicals contain agents which greatly
accelerate the corrosion of metals. Do not store the unit on or adjacent
to fertilizers or chemicals.
With the battery removed, use only mild soap and a damp cloth to
clean the unit. Never let any liquid get inside the unit; never immerse
any part of the unit into a liquid. Prevent the blades from rusting by
applying a film of light machine oil after cleaning.
9
9
ACCESSORIES
WARNING: DO NOT use the Hedge Trimmer with
any type of accessory or attachment. Such usage might be
hazardous.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling
Corporation) Seal on the LI-ION battery (or battery
pack) indicates that the costs to recycle the battery (or
battery pack) at the end of its useful life have already been paid by
Black & Decker.
RBRC™ in cooperation with Black & Decker and other battery users,
has established programs in the United States to facilitate the
collection of spent LI-ION batteries. Help protect our environment and
conserve natural resources by returning the spent LI-ION battery to
an authorized Black & Decker service center or to your local retailer
for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery.
registeredtrademark of the Rechargeable Battery Recycling Corporation.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel
to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory
under "Tools—Electric" or call: 1-800-544-6986 or visit
www.blackanddecker.com.
RBRC™ is a
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against
any defects in material or workmanship. The defective product will be
replaced or repaired at no charge in either of two ways.
The first is to return the product to the retailer from whom it was
purchased (provided that the store is a participating retailer). Returns
should be made within the time period of the retailerʼs policy for
exchanges (usually 30 to 90 days after the sale). Proof of purchase
may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for
exchanges.
The second option is to take or send the product (prepaid) to a
Black & Decker owned or authorized Service Center for repair or
replacement at our option. Proof of purchase may be required.
Black & Decker owned and authorized Service Centers are listed
under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you
specific legal rights and you may have other rights which vary from
state to state or province to province. Should you have any
questions, contact the manager of your nearest Black & Decker
Service Center. This product is not intended for commercial use.
LATIN AMERICA: This warranty does not apply to products sold in
Latin America. For products sold in Latin America, checkcountry
specific warranty information contained in the packaging, call the local
company or see the website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels
become illegible or are missing, call 1-800-544-6986 for a free
replacement.
10
TROUBLESHOOTING
Problem Possible Cause Possible Solution
• Slow running, noisy or hot blades. • Dry, corroded blades. • Lubricate blades.
• Unit will not start. • Battery not installed properly. • Check battery installation.
• Battery wonʼt charge. • Battery not inserted into charger. •Insertbattery intochargeruntilgreenLED appears.
For assistance, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK &
DECKER help line at 1-800-544-6986.
• Blades or blade support bent. • Straighten blade or blade support.
• Bent or damaged teeth. • Straighten teeth.
• Loose blade bolts. • Tighten blade bolts.
• Battery not charged. • Check battery charging requirements.
• Lock off not fully operated. • Check that lock off is fully forward prior to
moving main trigger.
Charge up to 8 hours if battery totally drained.
• Charger not plugged in. • Plug charger into a working outlet. Refer to
“Important Charging Notes” for more details.
• Check current at receptacle by plugging in a
lamp or other appliance.
• Check to see if receptacle is connected to a
light switch which turns power off when you turn
out the lights.
• Surrounding air temperature too hot • Move charger and tool to a surrounding air
or too cold. temperature of above 40 degree F (4.5°C) or
below 105 degree F (+40.5°C).
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
See ʻTools-Electricʼ
– Yellow Pages –
for Service & Sales
11
TAILLE-HAIE AVEC BLOC-PILES AU
LITHIUM, 20 V MAX.*
MODE DʼEMPLOI
Numéro de catalogue LHT120
Merci dʼavoir choisi Black & Decker!
Consulter le site Web
www.BlackandDecker.com/NewOwner
pour enregistrer votre nouveau produit.
ALIRE AVANT DERETOURNERCE PRODUIT
POUR QUELQUE RAISON QUE CE SOIT :
Si des questions ou des problèmes surgissent après lʼachat dʼun produit
Black & Decker, consulter le site Web
HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS
pour obtenir des réponses instantanément 24 heures par jour.
Si la réponse est introuvable ou en lʼabsence dʼaccès à lʼ Internet,
composer le 1 800 544-6986 de 8 h à 17 h HNE, du lundi au vendredi,
pour parler avec un agent.
Prière dʼavoir le numéro de catalogue sous la main lors de lʼappel.
CONSERVER CE MANUEL POUR UN USAGE ULTERIEUR.
Numéro de modèle LHT120
*La tension initiale maximale du bloc-piles (mesurée sans charge de
travail) est de 20 volts. La tension nominale, mesurée avec une
charge de travail, est de 18 volts.
12
Loading...