Black & Decker Kd960, Kd650, Kd70kc Instruction Manual

Download

www.blackanddecker.co.uk

43 1 2

Ireland

Australia

New Zealand

10 6 11

13 6 1112

16 14

8 9

Intended use

Your Black & Decker rotary hammer drill has been designed for drilling in wood, metal, plastics, and masonry as well as for screwdriving and light chiselling applications. This tool is intended for consumer use only.

General safety rules

Warning! Read all instructions. Failure to follow all instructions

listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool. SAVE THESE INSTRUCTIONS.

1. Work area a. Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2. Electrical safety a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

3. Personal safety a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal injury.

b. Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Avoid accidental starting. Ensure the switch is in

the off position before plugging in. Carrying power

tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are connected and properly used. Use of these

devices can reduce dust related hazards.

4. Power tool use and care a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before

making any adjustments, changing accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool

for operations different from those intended could result in a hazardous situation.

5. Service a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for hammer drills

◆ Wear ear protectors. Exposure to noise can cause

hearing loss.

◆ Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

◆ Preferably wear a dust mask.

◆ Slacken the knob (9).

◆ Insert the depth stop (8) into the mounting hole as shown.

◆ Set the depth stop to the desired position. The maximum

drilling depth is equal to the distance between the tip of the drill bit and the front end of the depth stop.

◆ Tighten the knob (9).

Fitting an accessory (fig. B)

◆ Clean and grease the shank (10) of the accessory.

◆ Pull back the sleeve (11) and insert the shank into the tool

holder (6).

◆ Push the accessory down and turn it slightly until it fits

into the slots.

◆ Pull on the accessory to check if it is properly locked.

The hammering function requires the accessory to be able to move axially several centimetres when locked in the tool holder.

◆ To remove the accessory, pull back the sleeve (11) and

pull out the accessory.

Electrical safety

This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Variable speed control knob

5. Drilling mode selector

6. Tool holder

7. Side handle

8. Depth stop

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle and depth stop (fig. A)

◆ Turn the grip counterclockwise until you can slide the side

handle (7) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Tighten the side handle by turning the grip clockwise.

Fitting the keyed chuck (fig. C)

◆ Fit the shank (12) of the supplied chuck (13) into the tool

holder as described above.

Warning! Never use standard chucks in the hammer drilling mode.

Fitting accessories in the keyed chuck (fig. D)

◆ Open the chuck by turning the sleeve (14).

◆ Insert the bit shaft (15) into the chuck.

◆ Insert the chuck key (16) into each hole (17) in the side of

the chuck and turn until tight.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, floors or ceilings, check

for the location of wiring and pipes.

Selecting the operating mode (fig. E)

The tool can be used in three operating modes. Rotate the drilling mode selector (5) towards the required position, as indicated by the symbols.

Drilling

◆ For drilling in steel, wood and plastics, and for

screwdriving set the operating mode selector (5) to the

position.

◆ When screwdriving, start at a low speed. When removing

screws, the speed is automatically reduced.

Hammer drilling

◆ For hammer drilling in masonry and concrete, set the

operating mode selector (5) to the position

◆ When hammering, the tool should not bounce and run

smoothly. If necessary, increase the speed.

Hammering

◆ For hammering with spindle lock, and for light chiselling

and chipping, set the operating mode selector (5) to the

position.

◆ Make sure the forward/reverse switch is in the forward

position.

◆ When changing from hammer drilling to chiselling,

turn the chisel to the desired position. If resistance is felt during mode change, slightly turn the chisel to engage the spindle lock.

Accessories

The performance of your tool depends on the accessory used. Black & Decker and Piranha accessories are engineered to high quality standards and designed to enhance the performance of your tool. By using these accessories you will get the very best from your tool.

Maintenance

Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

◆ Regularly clean the ventilation slots with a clean,

dry paint brush.

◆ To clean the tool, use only mild soap and a damp cloth.

Never let any liquid get inside the tool and never immerse any part of the tool into liquid.

Selecting the direction of rotation

For drilling, for tightening screws and for chiselling, use forward (clockwise) rotation. For loosening screws or removing a jammed drill bit, use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (3) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

Warning! Never change the direction of rotation while the motor is running.

Setting the drilling depth (fig. F)

◆ Slacken the knob (9).

◆ Set the depth stop (8) to the desired position. The maximum

drilling depth is equal to the distance between the tip of the drill bit and the front end of the depth stop.

◆ Tighten the knob (9).

Switching on and off

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch. Set the variable speed control knob (4) to the required speed range. As a general rule, use low speeds for large diameter drill bits and high speeds for smaller diameter drill bits.

◆ For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available only in forward (clockwise) rotation.

◆ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press the variable speed switch once more and release it.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

◆ Safely dispose of the old plug.

◆ Connect the brown lead to the live terminal in the new

plug.

◆ Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 5 A.

Protecting the environment

Separate collection. This product must not be disposed of with normal household waste.

Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com

Technical data

KD650 KD70 KD960

Voltage VAC230 230 230 Power input W 600 700 750 No-load speed min-10 - 900 0 - 900 0 - 900 Impact rate min-10 - 4,850 0 - 4,850 0 - 4,850 Impact energy J 1.8 2.2 2.2 Max. drilling capacity

Concrete mm 20 20 20 Steel mm 13 13 13 Wood mm 30 30 30

Weight kg 3.5 3.5 3.5

EC declaration of conformity

KD650/KD70/KD960

Black & Decker declares that these products conform to:

98/37/EC, 89/336/EEC, EN 55014, EN 60745, EN 61000

◆ The product has been used for trade, professional or hire

purposes;

◆ The product has been subjected to misuse or neglect;

◆ The product has sustained damage through foreign

objects, substances or accidents;

◆ Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk

LpA (sound pressure) 95 dB(A), LWA (acoustic power) 106 dB(A),

hand/arm weighted vibration 4.62 m/s

KpA (sound pressure uncertainty): 3 dB(A),

KWA (acoustic power uncertainty) 3 dB(A)

Kevin Hewitt

Director of Consumer Engineering

Spennymoor, County Durham DL16 6JG,

United Kingdom

1-1-2005

Guarantee

Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless: