Black & Decker Hx220 Instruction Manual [ar]
AR PT FR EN
www.blackanddecker.ae
HX220
ENGLISH
Parts Identification
1. Mode setting switch
2. Thermostat control switch
3. Indicator
4. Outlet grill
2
ENGLISH
Intended use
Your Black & Decker appliance is intended
for heating rooms.
Do not use this appliance for any other
purpose. This appliance is intended for use
in household and similar applications such
as: sta kitchen areas in shops, oces and
other working environments; farm houses;
by clients in hotels, motels and other
residential type environments; bed and
breakfast type environments.
Read this entire manual carefully
before using the appliance.
Safety instructions
Warning! When using mains-powered
appliances, basic safety precautions,
including the following, should always be
followed to reduce the risk of fire, electric
shock and personal injury.
• The intended use is described in this
manual. The use of any accessory or
attachment or the performance of any
operation with this appliance other than
those recommended in this instruction
manual may present a risk of personal
injury.
• Retain this manual for future reference.
Using your appliance
• Always take care when using the
appliance.
• Never pull the power supply cord to
disconnect the plug from the socket.
Keep the power supply cord away from
heat, oil and sharp edges.
• Do not place the appliance on or near
heat sources or in a heated oven.
• Do not use the appliance outdoors.
• Always protect the motor unit from water
or excessive humidity.
• If the power supply cord is damaged
during use, disconnect the appliance from
the power supply immediately. Do not
touch the power supply cord before
disconnecting from the power supply.
• Disconnect the appliance from the power
supply when not in use, before fitting or
removing parts and before cleaning.
• Never let the appliance operate
unattended.
• Do not let the cord hang over the edge of
a table, counter, or touch hot surfaces.
• Fully uncoil then guide the power supply
cord neatly so it cannot be caught
accidentally or tripped over.
• The heater must not be located
immediately below a socket-outlet.
• To prevent overload and blown fuses, do
not plug other appliance into same outlet
(receptacle)
• Do not place the heater on carpets, don’t
place the cable under carpets. Arrange
cord away from trac areas so that it will
not be tripped over.
• NEVER use this heater where it may
come into contact with water i.e.
bathroom, shower room, kitchen. Do not
use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
3
ENGLISH
Warning! In order to avoid overheating, do
not cover the heater. NEVER use the heater
to dry clothes or similar articles.
• Don’t touch the hot surfaces.
• Do not position the appliances in close
proximately to curtains or other
combustible materials. Keep combustible
material such as furniture, cushions,
bedding, paper, clothes, curtains etc. at
least 1.0m away from the heater.
• Always ensure that hands are dry before
operating or adjusting any switch on the
product or touching the plug and mains
supply connections.
• Do not use this heater with a
programmer, timer, separate
remote-control system or any other
device that switches the heater on
automatically, since a fire risk exists if the
heater is covered or positioned
incorrectly.
• To prevent a possible fire, do not block
air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed,
where openings may become blocked.
or stored.
• The most common cause of overheating
is deposits of dust or fluff in the
appliance. Ensure these deposits are
removed regularly by unplugging the
appliance and vacuum cleaning air vents
and grilles.
• Always use the heater in an upright
position.
• Do not use the appliance in rooms less
than 4m
• To disconnect the appliance, switch it
“OFF” then remove the plug from outlet.
Do not pull out the cord because this
could damage it.
• The temperature of accessible surfaces
may be high during use and for some
time afterwards.
Warning! This heater is not equipped with a
device to control the room temperature. Do
not use this heater in small rooms when
they are occupied by persons not capable
of leaving the room on their own, unless
constant supervision is provided.
2
area.
• Do not store away until the heater cools
down, store the heater in cool dry
location when not in use.
• Don’ t use extension cable
• Always operate on a flat horizontal
surface.
• Do not insert or allow foreign objects to
enter any ventilation or exhaust opening,
as this may cause an electric shock, fire
or damage to the appliance.
• Do not operate in areas where gasoline,
paint or other flammable liquids are used
4
• Always leave sufficient space around the
heater for ventilation.
Safety of others
• This appliance is not intended for use by
persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
ENGLISH
• Do not allow children or any person
unfamiliar with these instructions to use
the appliance.
• Do not allow children or animals to come
near the work area or to touch the
appliance or power supply cord.
• Close supervision is necessary when the
appliance is used near children.
CAUTION - Some parts of this product can
become very hot and cause burns.
Particular attention has to be given where
children and vulnerable people are present.
• Children should be supervised to ensure
that they do not play with the appliance.
After use
• Remove the plug from the socket before
leaving the appliance unattended and
before changing, cleaning or inspecting
any parts of the appliance.
• When not in use, the appliance should be
stored in a dry place. Children should not
have access to stored appliances.
Inspection and repairs
• Switch off the appliance before cleaning,
changing accessories or approaching
parts which move in use
• Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may aect
its operation.
• Do not use the appliance if any part is
damaged or defective.
• Have any damaged or defective parts
repaired or replaced by an authorised
repair agent.
• Before use, check the power supply cord
for signs of damage, ageing and wear.
• Do not use the appliance if the power
supply cord or mains plug is damaged or
defective.
• If the power supply cord or mains plug is
damaged or defective it must be
repaired by an authorised repair agent in
order to avoid a hazard. Do not cut the
power supply cord and do not attempt
to repair it yourself.
• Never attempt to remove or replace any
parts other than those specified in this
manual.
Electrical safety
Before use, check the mains voltage
corresponds to the voltage on the rating
plate.
This appliance is double insulated
therefore no earth wire is required.
• To avoid the risk of electric shock, do not
immerse the cord, plug or motor unit in
water or other liquid.
• Check that the supply voltage shown on
the rating plate of the appliance matches
that of your electrical system. Any
connection error will invalidate the
guarantee.
Warning: In order to avoid
overheating, do not cover the
heater.
Caution : Hot Surface.
Mains plug replacement
If a new mains plug needs to be fitted:
• Safely dispose of the old plug
• Connect the brown lead to the live
terminal of the new plug
5
ENGLISH
• Connect the blue lead to the neutral
terminal
• If the product is class I (earthed),
connect the green/yellow lead to the
earth terminal
Warning! If your product is class II double
insulated (only 2 wires in the cord set), no
connection is to be made to the earth
terminal
• Follow the fitting instructions supplied
with good quality plugs
• Any replacement fuse must be of the
same rating as the original fuse supplied
with the product
Mode setting:
The fan heater incorporates a rotate on
switch you can select the dierent air by
turning the switch clockwise to:
O
0
Fan only
Warm air
I
Hot air
II
Thermostat
When heating mode is selected
• Turn the thermostat knob in a clockwise
direction to the max position.
• Once the room has reached the desired
temperature, turn the thermostat knob
slowly in an anti-clockwise direction until
a "click" sound is heard. That is the
setting temperature. Now, the
thermostat is switched o.
• The thermostat will automatically
maintain the set temperature. It will
switch on when the room temperature is
below and switch o if above the
setting.
• The indicator lamp shows that heating
mode is switched on.
Use
Your appliance is fitted with a thermostat
for your safety. Using the appliance
continuously for very long periods may
cause the appliance to overheat and stop
working. It is therefore recommended that
you disconnect the appliance from the
mains supply and allow to fully cool before
continuing use.
1. Place the appliance on a flat, stable
surface.
2. Connect it to the electricity supply.
3. Select the operating mode.
4. Set the thermostat to the required
setting.
Maintenance & cleaning
• Switch the appliance off then remove the
plug from the power socket.
• The appliance is easier to clean if you do
so immediately after use.
• Do not use abrasive cleaning agents,
scourers, acetone, alcohol etc. to clean
the appliance.
• Clean the motor unit with a damp cloth.
Never immerse the motor unit in water
nor rinse it under the tap.
Technical data
HX220
Voltage 220 – 240 Volts
Supply 50 Hz
Power consumption 1800 W
Weight 1.5 Kg
6
ENGLISH
Protecting the environment
Separate collection. This product
must not be disposed of with normal
household waste.
Should you find one day that your Black &
Decker product needs replacement, or if it is
of no further use to you, do not dispose of it
with household waste. Make this product
available for separate collection.
Separate collection of used
products and packaging allows
materials to be recycled and used
again. Reuse of recycled materials helps
prevent environmental pollution and
reduces the demand for raw materials.
• Local regulations may provide for
separate collection of electrical products
from the household, at municipal waste
sites or by the retailer when you
purchase a new product.
• Black & Decker provides a facility for
recycling Black & Decker products once
they have reached the end of their
working life. This service is provided free
of charge. To take advantage of this
service, please return your product to
any authorised repair agent who will
collect them on our behalf.
• You can check the location of your
nearest authorised repair agent by
contacting your local Black & Decker
oce at the address indicated in this
manual. Alternatively, a list of authorized
Black & Decker repair agents and full
details of our after-sales service and
contacts are available on the Internet at:
www.2helpU.com.
Warranty
Black & Decker is confident of the quality of
its products and oers an outstanding
warranty.
This warranty statement is in addition to and
in no way prejudices your statutory rights.
The warranty is valid within the territories of
the Member States of the European Union
and the European Free Trade Area.
If a Black & Decker product becomes
defective due to faulty materials,
workmanship or lack of conformity, within
24 months from the date of purchase, Black
& Decker warranty to replace defective
parts, repair products subjected to fair wear
and tear or replace such products to ensure
minimum inconvenience to the customer
unless:
The product has been subjected to
The product has sustained damage
Repairs have been attempted by
To claim on the warranty, you will need to
submit proof of purchase to the seller or an
authorised repair agent. You can check the
location of your nearest authorised repair
agent by contacting your local Black &
Decker oce at the address indicated in this
manual.
Alternatively, a list of authorised Black &
Decker repair agents and full details of our
after-sales service and contacts are available
on the Internet at: www.2helpU.com.
The product has been used for
trade, professional or hire
purposes;
misuse or neglect;
through foreign objects,
substances or accidents;
persons other than authorised
repair agents or Black & Decker
service sta.
7
FRANÇAIS
Identification des pièces
1. Commutateur du mode
2. Commutateur du thermostat
3. Voyant lumineux
4. Grille de sortie d’air
8
FRANÇAIS
Utilisation
Votre appareil BLACK & DECKER est conçu
pour le défroissage à la vapeur des tissus.
Ne pas se servir de cet appareil pour un
autre usage. Cet appareil est destiné à un
usage domestique et des applications
similaires telles que : cuisines du personnel
dans les magasins, les bureaux et d’autres
environnements de travail ; maisons de
campagne ; clients dans les hôtels, motels
et autres types d’environnement résidentiel ;
environnements du type chambres d’hôtes.
Lisez attentivement la totalité de
ce manuel avant de vous servir de
l’appareil.
Consignes de sécurité
Avertissement! Lorsqu’on utilise un appareil
électrique, il faut toujours respecter
certaines règles de sécurité fondamentales,
notamment les suivantes, afin de prévenir
les risques d’incendie, de décharges
électriques ou de blessures corporelles.
• Ce manuel décrit la manière d’utiliser cet
appareil. L’utilisation d’un accessoire ou
d’une fixation, ou l’utilisation de cet
appareil à d’autres fins que celles
recommandées dans ce manuel
d’instruction peut présenter un risque de
blessures corporelles.
• Conservez ce manuel pour un usage
ultérieur.
Utilisation de votre appareil
• Prenez toutes les précautions nécessaires
pendant l’utilisation de l’appareil.
• Ne tirez jamais sur le cordon
d’alimentation pour débrancher la fiche
de la prise. Gardez le cordon
d’alimentation éloigné de toute source
de chaleur, de zones graisseuses et de
bords tranchants.
• Ne placez pas l’appareil sur ou près de
sources de chaleur ou dans un four
chaud.
• N’utilisez pas l’appareil à l’extérieur.
• Protégez toujours le bloc moteur de l’eau
ou d’une humidité excessive.
• Si le cordon d’alimentation est
endommagé pendant l’utilisation,
débranchez immédiatement l’appareil. Ne
touchez pas au cordon d’alimentation
avant d’avoir débranché l’appareil.
• Débranchez l’appareil de l’alimentation
secteur lorsqu’il n’est pas utilisé, avant de
monter ou de démonter des éléments et
avant de le nettoyer.
• Ne laissez jamais fonctionner l’appareil
sans surveillance.
• Ne pas laisser le cordon pendre d’une
table ou d’un plan de travail, ou être en
contact avec une surface chaude.
• Déroulez entièrement le cordon
d’alimentation, puis positionnez-le avec
soin de sorte qu’il ne se coince pas et
pour éviter qu’il fasse trébucher
quelqu’un.
• Le radiateur ne doit pas être placé juste
en-dessous d’une prise secteur.
• Pour éviter une surcharge et griller les
fusibles, ne pas brancher un autre
appareil sur la même prise
(alimentation).
• Ne pas poser le radiateur sur un tapis, ne
pas placer le cordon sous un tapis.
Eloigner le cordon des zones de passage
pour éviter qu’il fasse trébucher
quelqu’un.
• NE JAMAIS utiliser ce radiateur dans un
endroit où il pourrait être en contact avec
de l’eau, comme une salle de bains, une
salle d’eau ou une cuisine. Ne pas utiliser
ce radiateur près d’une baignoire, d’une
douche ou d’une piscine.
9
Loading...