Black & Decker D5000, D5500 User Manual

Please Read and Save this Use and Care Book Por favor lea este instructivo antes de usar el producto Veuillez lire et conserver ce guide d’entretien et d’utilisation

Digital Evolution

™

Iron

Plancha Fer

Accessories/Parts (USA/Canada) Accesorios/Partes (EE.UU/Canadá) Accessoires/Pièces

(É.-U./Canada)

1-800-738-0245

USA/Canada 1-800-231-9786 Mexico 01-800-714-2503

www.blackanddecker.com

Models Modelos Modèles

❑

D5000

❑

D5500

When using your iron, basic safety precautions should always be followed, including the following:

❑

READ ALL INSTRUCTIONS BEFORE USING.

❑

Use iron only for its intended use.

❑

To protect against a risk of electric shock, do not immerse the iron in water or other liquids.

❑

The iron should always be turned to “Off” before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead grasp plug and pull to disconnect.

❑

Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around the iron when storing.

❑

Always disconnect iron from electrical outlet when filling with water or emptying and when not in use.

❑

Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron, take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.

❑

Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board.

❑

Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down- there may be hot water in the reservoir.

SPECIAL INSTRUCTIONS

❑

To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit.

❑

If an extension cord is absolutely necessary, a 10-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS.

Soft-Touch Parts Note: The soft-touch parts of this unit are free of natural rubber and latex.

They are safe for individuals allergic or sensitive to these materials.

POLARIZED PLUG

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

TAMPER-RESISTANT SCREW Warning: This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts

inside. Repair should be done only

by authorized service personnel.

Note: If the power supply cord is damaged, it should be replaced by qualified personnel or in Latin America by an authorized service center.

How to Use

This appliance is intended for household use only.

GETTING STARTED

Remove any labels, stickers or tags attached to the body or soleplate of the iron. Note: Use ordinary tap water for ironing. Do not use water processed through a home

softening system. Important: For optimum performance, let the iron stand for 90 seconds before beginning to

iron.

Filling Water Tank

1. Grip each side of the water-fill cover and pull open (A).

2. Tilt the iron and using a clean measuring cup, pour water into opening until the water reaches the MAX level mark on the water tank (B). Do not overfill.

3. Close the water-fill cover.

Note: If you need to add water while ironing, unplug the iron and follow above steps.

4. Plug the iron into an electrical outlet.

• The iron beeps.

• Digital display window illuminates and fabric setting

1 (ACRYL) displays on the window with a flashing up arrow and a circle around the iron symbol (C).

5. Once the iron reaches the preset temperature, it beeps and the display shows the set temperature, fabric type and the iron symbol without the circle (D).

SELECTING FABRIC TEMPERATURE

1. Read garment's label to help you determine fabric type.

Tip: If unsure of a garment's fiber, test a small area (on an inside

seam or hem) before ironing.

2. Once you determine the fabric type, select appropriate temperature setting (from 1 to 7).

To set fabric temperature:

1. Use the pushbuttons on either side of the digital display

window (E).

2. Press the (+) button to select a higher setting.

3. Press the (-) button to select a lower setting. Tip: As a guide, the digital display shows the setting number with

the corresponding fabric type.

4. Once the iron reaches the selected temperature, it beeps and shows the selected temperature number with corresponding fabric type and the iron symbol.

Product may vary slightly from what is illustrated.

1. Spray nozzle

2. Water-fill cover

3. Steam On/Off button

4. Fabric temperature selector pushbuttons (+ and -)

5. Digital display

6. Steam button

7. Spray button

8. Comfort Grip

™

handle

9. Heel rest

10. Water tank

11. AUTO CLEAN

button

12. Soleplate

Surge-of-Steam

Spray

Auto Off

Symbols





























IRONING WITH STEAM Smart Steam

™

Technology

The Smart Steam

™

system generates steam at higher temperature

settings (between 5 and 7) (F). Once you select the temperature, the Smart Steam

™

technology detects the set temperature and adjusts the steam power accordingly. The higher the setting, the more powerful the steam.

Surge of Steam

Use to remove stubborn creases.

1. With the water tank filled to the MAX mark, press appropriate fabric temperature selector pushbutton to select the setting (between 5 and 7) for your fabric. Read garment's label to help you determine fabric type.

Note: Steam is automatically turned off between settings 1 and 4.

2. Once you select the appropriate fabric setting, wait for iron to beep and display selected setting.

3. Press the Steam On/Off button to turn on the steam function. The Steam symbol on the digital display flashes, indicating that steam function is ready (G).

4. Press the surge-of-steam button to generate a burst of steam (H). For best performance, leave an interval of 5 seconds between bursts.

Important: Always stand the iron on its heel rest when powered on but not in use.

Vertical Steam

Use for removing wrinkles from hanging clothes and drapes.

1. Make sure the water tank is filled to the MAX mark and iron is plugged into electrical outlet.

2. Press Steam On/Off button to activate steam function.

3. Hang the garment to be steamed on a clothes hanger. (Curtains or drapes can be steamed once they are hung.)

4. Press appropriate fabric temperature selector pushbutton to select appropriate setting (between 5 and 7) for your fabric.

5. Wait for iron to beep and digital display to show selected setting with a flashing steam symbol.

6. Hold the iron close to, but not touching, the fabric.

7. Pull the fabric tight in your free hand and pump the surge-ofsteam button as you move the iron over the fabric (J).

Important: Always stand the iron on its heel rest when powered on but not in use.

USING SPRAY

Use to dampen tough wrinkles at any setting (K).

1. Be sure the iron is filled with water.

2. On first use, pump the spray button several times.

IRONING WITHOUT STEAM Note: You can use the Steam On/Off button to turn off the steam

function in all settings (1-7).

1. Select setting 1, 2, 3 or 4 to iron without steam (L). The Smart

Steam

™

system will automatically turn off and there will not be

any steam generated.

2. To dry iron at higher settings, empty the water from the reservoir to prevent steaming.

3. Plug in the iron, wait until iron beeps and digital display shows selected setting. If the steam symbol is flashing, press the Steam On/Off button to turn off the steam function.

Tip: The steam symbol becomes steady, indicating the steam function is off. EMPYTING WATER TANK (OPTIONAL) Note: It is not necessary to empty the water after each use.

1. Unplug the iron and let it cool.

2. To release the water, hold the iron over a sink with the tip pointing down. Water will empty out of the water-fill opening (M).

SPECIAL FEATURES 3-Way Automatic Shutoff

The automatic shutoff feature in your iron works as follows:

• The iron will shut off after 30 seconds of inactivity if left on its soleplate or tipped over on its side. If left vertically on its heel rest, it will shut off after 8 minutes of inactivity (N) .

• The unit beeps once and the AUTO OFF symbol flashes on the digital display to let you know the iron has stopped heating (P).

• After a few seconds, the digital display light goes off.

• If you pick up the iron, an internal motion-sensitive detector is activated and the iron starts heating again.

Tip: You might have to move the iron or shake it gently.

• The unit beeps two times, the digital display light comes on and the set temperature is displayed again.

Note: Wait for iron to reheat completely before resuming operation. Anti-Drip System

The anti-drip system prevents water spotting at low temperatures.



8 minutes

30 seconds

L EA

MAX

M A

AU T O C L

E A N

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Cuando se utilizan aparatos eléctricos, especialmente en la presencia de los niños, siempre se debe tomar ciertas medidas de seguridad, incluyendo las siguientes:

❑

LEA TODAS LAS INSTRUCCIONES ANTES DE UTILIZAR EL

PRODUCTO.

❑

Utilice la plancha solamente con el fin previsto.

❑

A fin de evitar el riesgo de un choque eléctrico, no sumerja la plancha en agua ni en ningún otro líquido.

❑

Siempre ajuste la plancha a la posición de apagado (OFF) antes de conectarla o desconectarla de la toma de corriente. Nunca tire el cable para desconectar el aparato; sujete el enchufe y hale con cuidado.

❑

No permita que el cable entre en contacto con las superficies calientes. Espere que la plancha se enfríe bien antes de guardarla. Enrolle el cable holgadamente alrededor de la plancha.

❑

Siempre desconecte la plancha cuando no esté en uso y cuando llene o vacíe el tanque de agua.

❑

No utilice la plancha si el cable o el enchufe presentan algún desperfecto, si la ha dejado caer o dañado. Para evitar el riesgo de un choque eléctrico, no desarme la plancha. Acuda a una persona de servicio calificada. El reensamblaje incorrecto de la plancha puede ocasionar el riesgo de un choque eléctrico.

❑

Se requiere supervisar de cerca todo aparato eléctrico al ser utilizado por o en la presencia de los niños. Nunca descuide la plancha mientras permanece enchufada ni sobre la tabla de planchar.

❑

Pueden ocurrir quemaduras al tocar las piezas metálicas, el agua caliente, o el vapor que emite la plancha. Tenga cuidado al invertir una plancha de vapor ya que puede haber agua caliente adentro del tanque.

INSTRUCCIONES ESPECIALES

❑

Para evitar una sobrecarga eléctrica, no utilice ningún otro aparato de alto consumo de corriente en el mismo circuito.

❑

Si el uso de un cable de extensión es indispensable, se debe de utilizar uno de 10 amperios. Los cables de menor amperaje se pueden sobrecalentar. Se debe tener cuidado de acomodar el cable de manera que nadie lo hale ni se tropiece.

CONSERVE ESTAS INSTRUCCIONES.

Care and Cleaning

This product contains no user-serviceable parts. Refer service to qualified service personnel.

Cleaning Outside Surfaces

1. Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outer surfaces with a soft cloth dampened with water. Add mild household detergent. Never use abrasives, heavy-duty cleansers, vinegar or scouring pads that may scratch or discolor the iron.

2. After cleaning, steam iron over an old cloth to remove any residue from the steam vents.

AUTO CLEAN

System

To keep the steam vents free of any buildup, about once a month follow these instructions.

1. Fill the water tank well below the MAX line. Plug in the iron.

2. Select fabric temperature setting 6 and stand the iron on its heel rest.

3. Wait for the iron to beep and display temperature number with corresponding fabric.

4. Unplug the iron and hold over a sink with the soleplate facing down.

5. Press and hold the AUTO CLEAN

button. Be careful, as hot

water and steam will come out of the steam vents (Q). Continue to hold the AUTO CLEAN

button until all the water has

emptied. If necessary, rock iron side to side and front to back.

6. When finished, release the button, stand the iron on its heel rest and plug it in. Heat for about 2 minutes to dry out any remaining water.

Storing your Iron

1. Unplug the iron and allow it to cool.

2. Store vertically on its heel to prevent water leaking from the soleplate.



+ 10 hidden pages