Black & Decker SPCM1936 TYPE 1, CM1836 TYPE 2, CM1836 TYPE 1 Owner’s Manual
19 inch (483mm) Cordless Mulching Rear Bag Mowers
I STRUCTION MANUAL
Catalog Number CM1936Z
Date Code:
Catalog Number SPClV11936
Date Code:
Thank you for choosing Black & Decker!
Go to www.BiackandDecker.com/NewOwner to register your new product.
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON:
IfyouhaveaquestionorexperienceaproblemwithyourBlack&Deckerpurchase,goto HTTP://WWW.BLACKANDDECKER.CO[VI/1NSTANTANSWERS
for instantanswers24hoursaday.
Ifyoucan'tfindtheanswerordonothaveaccesstotheinternet,call1-800-544-6986from8a.m.to5 p,m.ESTMon.-- Fri.tospeakwithanagent.
Pleasehavethecatalognumberavailablewhenyoucall.
KEY iNFORMATiON YOU SHOULD KNOW:
- Do not operate mower unless handle is locked into position.
- For best cutting results, keep blade sharpened and balanced.
- Inspect and thoroughly clean your mower after each use (adeck with caked grass will degrade performance).
- Make sure mowing area is clear of other persons or pets prior to starting and during operation.
- Fully charge your mower before using it for the first time for optimal performance. Fully charge your battery after every use.
VEA EL ESPANOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA
ADVERTENClA: LI_ASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO
SAFETY GUiDELiNES - DEFiNiTiONS
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING
PROBLEMS. The symbols below are used to help you recognize this information.
Z_DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
z-_WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
z-_CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
The following are explanations of important safety hazard pictorials on the mower.
_Jl. User must read and understand the instruction manual.
2. To:::_ avoid the risk of serious injury do not mow up and down slopes. Always mow across slopes.
3. To avoid the risk of injury to bystanders keep all persons and pets at a safe distance from the mower while operating.
I 14 Rotating blades can cause serious injury. Keep hands and feet clear of mower deck and discharge opening at all times. Always be
I:_1 sure blade has stopped (wait for the blade to stop rotating (approximately 3 seconds) after releasing bail handle and removing the safety
key) before removing and replacing grass catcher, cleaning, servicing, transporting or lifting the mower.
5. Objects struck by mower blade can cause serious injury. Stay behind the handle when the motor is running. Always ensure persons
and pets are clear of the discharge from the mower while operating. Always inspect mowing area before mowing and remove objects
that could be thrown by blade. Release bail handle to turn mower off and wait for the blade to stop rotating (approximately 3 seconds)
before crossing walk, roads, patio and gravel drives.
Z_WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS
Z_WARNING: When using electric lawn mowers, basic safety precautions should always be followed to reduce risk of fire, electric shock, and
personal injury, including the following.
TO REDUCE RiSK OF INJURY:
• Before any use, be sure everyone using this lawn mower reads and understands all safety instructions and other information contained in this
manual.
• Save these instructions and review frequently prior to use and in instructing others.
READ ALL INSTRUCTIONS
/t',DANGER: IMPORTANT SAFE PRACTICES FOR WALK-BEHIND MOWERS
This mower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in seri-
ous injury or death.
GENERAL OPERATION
1. Read, understand, and follow all instructions on the mower and in the instruction manual before starting.
2. Do not put hands or feet near or under the mower. Keep clear of the discharge opening at all times.
3. Only allow responsible adults, who are familiar with the instructions, to operate this mower.
4. Clear the area where the mower is to be used of objects such as rocks, sticks, wire, toys, bones, etc., which could be thrown by the blade.
Objects struck by the blade can cause severe injury to persons. Stay behind the handle when the motor is running.
5. Be sure the area surrounding the mower is clear of bystanders before operating. All bystanders and pets should be kept at a safe distance.
Stop the mower if anyone enters the area surrounding the mower.
6. Do not operate mower barefooted or while wearing sandals. Always wear substantial footwear.
7. Do not pull mower backward unless absolutely necessary. Always look down and behind before and while moving backward.
8. Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward
the operator. Release bail handle to turn mower off and stop the blade when crossing gravel surfaces.
9. Do not operate mower without the entire grass catcher, discharge guard, rear guard, or other safety protective devices in place and working.
Periodically check all guards and safety protective devices to ensure they are in good working order and will operate properly and perform
their intended function. Replace a damaged latch, guard or other safety device before further use.
10. Never leave a running mower unattended.
11. Always release the bail handle to stop the motor and wait until the blade comes to a complete stop and remove the safety key before cleaning
the mower, removing the grass catcher, un-clogging the discharge guard, when leaving the mower, or before making any adjustments, repairs
or inspections.
12. Operate mower only in daylight or good artificial light when objects in the path of the blade are clearly visible from the operating area of the mower.
13. Do not operate mower while under the influence of alcohol or drugs, or when you are tired or ill. Always stay alert, watch what you are doing,
and use common sense.
14. Avoid dangerous environments. Never operate mower in damp or wet grass, never use mower in the rain. Always be sure of your footing;
walk; never run.
15. Disengage the drive system, if so equipped, before starting the motor.
16. If the mower should start to vibrate abnormally, release the bail handle, wait for the blade to stop and remove the safety key and battery pack,
then check for the cause immediately. Vibration is generally a warning of trouble.
17. Always wear proper eye and respiratory protection when operating the mower.
18. The use of any accessory or attachment not recommended for use with this mower could be hazardous. Only use accessories approved by
Black & Decker.
19. Never overreach while operating the mower. Always be sure to keep proper footing and balance at all times while operating the mower.
2
SLOPE OPERATION
Slopes are a major factor related to slip and fall accidents, which can result in severe injury. Operation on all slopes requires extra caution. If you
feel uneasy on a slope, do not mow it.
1. Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes.
2. Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could cause a slip and fall accident. Tall grass can hide obstacles.
3. Do not mow on wet grass or excessively steep slopes. Poor footing could cause a slip and fall accident.
4. Do not mow near drop-offs, ditches, or embankments. You could lose your footing or balance.
CHILDREN
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the mower and the mowing
activity. Never assume that children wilt remain where you last saw them.
1. Keep children out of the mowing area and under the watchful care of a responsible adult other than the operator.
2. Be alert and turn mower off if a child enters the area.
3. Never allow children to operate the mower.
4. Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child.
GENERAL SERVICE
1. Never operate mower in a closed area.
2. Keep all nuts and bolts tight to be sure the equipment is in safe working condition.
3. Never tamper with safety devices. Check their proper operation regularly.
4. Keep mower free of grass, leaves, or other debris build-up. Allow mower to cool before storing.
5. If you strike a foreign object, release bail handle to turn mower off, wait for the blade to stop and remove the safety key and battery pack, then
inspect the mower. Repair, any damage, before starting and operating the mower.
6. Never make any adjustments or repairs with the motor running or while the safety key is in the mower.
7. Always remove safety key and battery pack before adjusting, cleaning, repairing, inspecting,transporting, storing or leaving the mower.
8. Check grass catcher components and the discharge guard frequently and when necessary replace with Black & Decker recommended parts only.
9. Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.
10. Maintain or replace safety and instruction labels, as necessary.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment. This Class B digital apparatus complies with Canadian ICES-003.
SAVE THESE INSTRUCTIONS
Z_WARNING: GENERAL SAFETY WARNINGS AND iNSTRUCTiONS FOR ALL LAWN MOWERS
• STORE IDLE LAWN MOWER INDOORS. Always store with safety key removed. Lawn mowers should be stored indoors in dry, secured area -
out of reach of children.
• DON'T FORCE MOWER. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
• USE RIGHT APPLIANCE. Do not use the mower for any job except that for which it is intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves, long pants and substantial, non-
skid footwear are recommended when working outdoors.
• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with side shields, complying with applicable
safety standards and, when needed, a face shield. Also use face or dust mask if operation is dusty. This applies to all persons in the work area. Also
use a hard hat, hearing protection, gloves, safety shoes and dust collection systems when specified or required. Safety glasses or the like are
available at extra cost at your local dealer or Black & Decker Service Center.
• DON'T ABUSE CORD. Never carry charger by cord or yank it to disconnect from receptacle. Keep cord away from heat, oil, and sharp edges.
• MAINTAIN MOWER WITH CARE. Keep cutting edge clean and sharp for best performance and to reduce the risk of injury. Follow instructions for
lubricating and changing accessories. Inspect mower cord periodically and if damaged, have it repaired by authorized service facility. Keep handles
dry, clean, and free from oil and grease.
• AVOID UNINTENTIONAL STARTING. Don't carry mower with safety key inserted in switch housing. Be sure bail handle is not engaged while
inserting safety key.
• BEFORE USING, always visually inspect to see that the blade, blade fasteners and cutter assembly are not worn or damaged. Replace worn or
damaged blades and fasteners in sets to preserve balance. Inspect the mower cord - ensure it is in good condition. Cord insulation must be intact
with no cracks or deterioration.
• USE OF EXTENSION CORDS
Make sure the extension cord is in good condition before using. Always use the proper size extension cords with the lawn mower - that is, proper
wire size for various lengths of cord and heavy enough to carry the current the lawn mower wilt draw. Use of an undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. For proper size cords see chart below.
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gauge
Than Than
10 12 16 16 14 12
12 16 14 12 Not Recommended
Minimum Gauge for Cord Sets
(0-7,6m) (7,6-15,2m)(15,2-30,4m)(30,4-45,7m)
(0-15,2m)(15,2-30,4m)(30,4-60,9m)(60,9-91,4m)
6 18 16 16 14
10 18 16 14 12
• CHECKFORDAMAGEDPARTS.Beforefurtheruseofthemower,aguardorotherpartthatisdamagedshouldbecarefullycheckedto
determinethatitwilloperateproperlyandperformitsintendedfunction.Checkforalignmentofmovingparts,bindingofmovingparts,breakage
ofparts,mounting,andanyotherconditionsthatmayaffecttheiroperation.Aguardorotherpartthatisdamagedshouldbeproperlyrepairedor
replacedbyanauthorizedservicecenterunlessotherwiseindicatedelsewhere in this manual.
• REPAIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in this manual should be performed by Black & Decker
authorized service centers or other qualified service organizations, always using identical replacement parts.
/_DANGER: ADDiTiONAL WARNINGS FOR MOWERS
• ALWAYS firmly grip handle with both hands when operating mower.
• NEVER wear radio or music headphones while operating mower.
• CONTAIN long hair.
• NEVER attempt to make a wheel height adjustment while the motor is running or while the safety key is in the switch housing.
• IF MOWER stalls, release bait handle to turn mower off, wait for blade to stop and remove the safety key and battery pack, before attempting to
unclog the chute or remove anything from under the deck.
• KEEP HANDS and feet away from cutting area.
• KEEP BLADES sharp. Always use protective gloves when handling the mower blade.
• IF YOU are using a grass catcher, check it frequently for wear and deterioration. If excessively worn, replace with new bag for your safety.
• USE EXTREME CAUTION when reversing or pulling mower toward you.
z_WARNING: Some dust created by this product contains chemicals known to the State of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks that are specially designed to filter out
microscopic particles.
FUNCTIONAL DESCRIPTION
CM1936Z
1.) Safety key/charging port
• compounds in fertilizers
• compounds in insecticides, herbicides and pesticides
. arsenic and chromium from chemically treated lumber
2.) Bail Handle (Switch lever)
3.) Handle attachment bolts
4.) Handle quick adjust knobs
5.) Grass bag
6.) Cut height adjustment release
7.) Cut height indicator
8.) Removable battery
9.) Battery latch
10) Battery guage
11.) On Demand knob
FUNCTIONALDESCRIPTION
SPCM1936
1.) Safety key/charging port
2.) Bait Handle (Switch lever)
3.) Handle attachment bolts
4.) Handle quick adjust knobs
5.) Grass bag
6.) Cut height adjustment release
7.) Cut height indicator
8.) Removable battery
9.) Battery latch
10.) Battery guage
11.) On Demand knob
12.) Self Drive Bait Handle
13.) Speed Control Lever
PREPARATION
PLEASE REFER TO DIAGRAMS (A, B, C...) AND ITEM NUMBERS (1, 2, 3...) AS NOTED THROUGHOUT MANUAL. FOR EXAMPLE,
A=I REFERS TO ITEM 1 IN FIGURE A.
UNPACKING = (FIGURES A, B)
Z_ CAUTION: Pinch point. To avoid being pinched, keep fingers away
from area between handle and plates.
STEP 1:
Carefully cut down the sides of the,box on the opposite end of the handle
and fold the flap down as shown. ZL_ WARNING: Sharp blade. Keep
body parts away from blade.
STEP 2:
With the carton end cut open, remove the cardboard filler, charger,
accessory bag and grass bag and push the mower out of the opened
carton.
ASSEMBLY
Tools required for assembly, not supplied:
Adjustable or 1/2 inch (13mm) wrench.
HANDLE ASSEMBLY (FIGURE C)
1. Position the handle so that the handle holes line up with the deck side
plate holes. The handle quick adjust knobs C-2 wilt line up with the
deck side plate top holes.
2. Place handle attachment bolts C-1 through the handle holes and
thread into the deck side plate. Before tightening repeat for other side.
3. Tighten handle attachment bolts C-1 securely using adjustable or 1/2
inch (13mm) wrench.
4. To set desired handle height refer to handle adjustment. Do not push
or use mower unless handle is properly fastened and secured to
mower.
The handle quick adjust knobs C-2 will appear as shown in figure C
when they are fully engaged into the plates.
CAUTION: Pinch point. To avoid being pinched, keep fingers away from
area between handle and plates when raising or adjusting.
HANDLE ADJUSTMENT (FIGURE D)_
1. Remove safety key.
2. Hold handle with one hand, pull out and rotate one handle quick
adjust knob D-1 on mower handle a quarter-turn to release the pin
from the metal plate hole. Handle quick adjust knob D-1 will remain
in this retracted position. Repeat for the opposite side knob. Now the
handle is free to move into another handle height position.
3. Move the handle to desired height position. Taller users wilt prefer
using the top hole position, while shorter users may prefer the bottom
hole position. While holding handle with one hand, pull out and rotate
one handle quick adjust knob D-1 a quarter-turn to re-engage pin
into metal plate hole. Repeat for the other knob.
4. Shake handle slightly to ensure handle pins are fully engaged prior to
using mower. Do not push or use the mower unless handle is properly
fastened and secured to mower. The handle quick adjust knobs D-1
wilt appear as shown in figure D when the knob pins are fully engaged
into the plates.
CAUTION: Pinch point. To avoid being pinched, keep fingers away from
area between handle and plates when raising or adjusting.
ASSEMBLING THE GRASS CATCHER (FIGURES EI, E2, E3, E4).
1. Before starting to assemble the grass bag to the frame, check that the grass bag and frame are similar to figure El.
2. Slide the grass bag onto the frame as shown in figure E2.
3. Assemble the top clips to the frame as shown in figure E3, then assemble the two side clips and the bottom clip last.
4. Completely assembled grass catcher is shown in figure E4.
GRASSBAG
FRAME
CLiP
WHEEL HEIGHT ADJUSTMENT (1-1/2 IN. (38mm)1
TO 3-1/2 iN. (89ram) FIGURES F_G
NOTE: Certain types of grass or grass conditions may require varying
the height of the mower deck. Grasses of mature lawns often are
seriously injured when mowed shorter than 1-1/2 inches (38mm), and
a height of 1-1/2 to 2 inches (38mm) to (51mm) is preferred on large
lawns.
1. Before making any adjustments, release bail handle to turn mower
off, wait for blade to stop, and remove safety key.
2. Your mower features the Black & Decker one touch wheel height
adjustment system. This system will adjust all four wheels at the
same time.
3. To raise or lower the cutting height, place the palm of your hand on
the palm rest F=I and with your fingers, squeeze upward on the
finger grip F=2 and hold.
4. While holding the finger grip up you can raise or lower the cutting
height. The mower has seven blade height adjustment positions.
Refer to the scale G=I and pointer G=2 at the rear of the mower.
The pointer will indicate the height setting for cutting your lawn.
This setting can be a reference for the next time you want to cut
your lawn at the same height.
When you have the mower at the height you would like, hold it in
place with your left hand on the lower right handle bar and release
the finger grip with your right hand to lock the height adjust. Note:
To ensure that the deck is securely locked in one of the seven
positions, press down on the palm rest after releasing the finger grip.
m
I
,11
BATTERY
CAUTION: USE ONLY BLACK & DECKER APPROVED REPLACEMENT BATTERIES - CONTACT YOUR LOCAL SERVICE CENTER
OR 1-800=544=6986.
The battery is a 36-volt sealed lead acid system. There is no liquid contained within the battery and the mower/battery can therefore be stored in
any position without fear of leakage.
IT IS RECOMMENDED THAT THE BATTERY BE RECHARGED AFTER USE TO PROLONG THE BATTERY LIFE. FREQUENT CHARGING
WILL NOT HARM YOUR BATTERY, AND WILL ENSURE THAT THE BATTERY IS FULLY CHARGED AND READY FOR ITS NEXT USE.
STORING BATTERY NOT FULLY CHARGED WILL SHORTEN BATTERY LIFE. REFER TO OFF-SEASON STORAGE SECTION.
For optimal performance the battery should be kept on constant charge when not in use.
The battery should be charged in its proper orientation.
The battery prefers to be charged in a cool, dry place.
The battery does not need to be fully discharged before recharging.
2 to 3 initial charging cycles may be required after purchase to achieve maximum run time capacity.
A fully charged battery can be safely stored down to -40°C (-40°F).
The battery is maintenance free.
The CM1936Z can use either the RB3610 or RB3612 battery. The RB3612 battery is for use with the SPCM1936 mower only. The battery
should not be used for any other purpose.
BATTERY RUNTIME INDICATOR- FIGURE H i
Your battery pack is equipped with an integral Battery Runtime Indicator.
When you push the "i" button H=I, the indicator will give the battery
runtime level.
At full charge, if you push the "i" button, all three LED's wilt light up
indicating maximum runtime.
If you want to check the runtime during your cutting:
1. Release bail handle to turn mower off, wait until the blade stops and
remove safety key.
2. Push the "i" button to get an indication of runtime.
All three LED's lit indicate maximum runtime available.
Two LED's lit indicate approximately one-third to two-thirds of runtime
available.
One LED lit indicates less than one-third runtime available. You may need
to charge your battery soon. Refer to Charging Procedure.
\\
\
\
REMOVING BATTERY FROM MOWER - FIGURE !
The battery can be removed from the mower for storage/charging or left
in the mower for charging.
Prior to removing battery, place mower on level ground.
Release bail handle to turn mower off, wait for blade to stop, and remove
safety key.
To remove the battery, lift the lever I-1, and then rotate back away from
battery pack to unlatch clasp I-2. Lift battery pack out.
Prior to the installation of the battery pack, ensure that the mower is clear
of debris and the charger plug is disconnected from the battery pack.
CHARGER SAFETY RULES
1. Plug charger directly into an electrical outlet. DO NOT ABUSE THE
CORD. Never carry charger by cord. Do not disconnect the charger
from the outlet, mower or battery by pulling it by the cord.
2. /_ WARNING: To reduce the risk of fire, electrical shock, or
personal injury do not attempt to use this charger with any other
product. Likewise, do not attempt to charge the battery with any other
charger.
3. Do not service mower with charger, safety key or battery pack installed.
4. Do not operate a damaged charger. Replace damaged cords or
charger immediately at an authorized Black & Decker service center.
5. Always charge the mower in a dry area protected from the weather.
Do not expose the mower, battery or charger to rain. Do not charge in
wet locations. Do not charge battery when temperature is above 104°F (40°C) or below 41°F (5°C). Remove battery and charge indoors if
above or below these temperatures. Charge the battery in a well
ventilated location.
6. Keep the mower, battery and charger away from water, heat sources, (such as radiators, heaters, stoves, etc.) flames, or chemicals. Be
careful not to damage the charger cord, by keeping cord away from sharp edges.
7. Prior to reinstalling the battery into the mower, disconnect charger plug from battery, or damage may occur.
Z_WARNING: FiRE HAZARD
ALWAYS DISCONNECT THE CHARGER FROM THE POWER SUPPLY (WALL OUTLET) BEFORE REMOVING THE CHARGER
CONNECTOR. UNDER CERTAIN CONDITIONS, WITH THE CHARGER PLUGGED IN TO THE POWER SUPPLY, THE EXPOSED
CONNECTOR CAN BE SHORTED BY FOREIGN MATERIAL AND MAY CAUSE A FIRE.
FOREIGN MATERIALS OF A CONDUCTIVE NATURE, SUCH AS, BUT NOT LIMITED TO, STEEL WOOL, ALUMINUM FOIL, OR ANY
BUILD=UP OF METALLIC PARTICLES, SHOULD BE KEPT FROM THE CONNECTOR. ALWAYS UNPLUG CHARGER BEFORE
ATTEMPTING TO CLEAN.
CHARGING PROCEDURE- FIGURES J, K,L
The battery can be removed from the mower for charging or left in place
1. Remove safety key J=l.
2. Align the charger plug J=2 with the arrow J=4 on top and insert the
charger plug into the receptacle J=3 on the mower (green terminal to
green terminal, white terminal to white terminal) or remove the
battery and insert the charger plug K=l(with the arrow on top) into the
receptacle K=2 on the battery. The charger connector can only be
plugged into the mower receptacle or battery one way.
3. Insert the 120 volt plug L=I of the charger L=2 into the wall receptacle.
4. The red light L=3 on the charger should come on indicating you have
power and the battery is being charged. Check the charger for the red
light, if it is not on check the charger connector for proper alignment
(step 2). The red light should extinguish and the green light will
come on when charging is complete (takes approximately
12 - 20 hours to charge a fully discharged mower).
5. It is recommended to leave the battery on constant charge (between
mowing uses) for optimum performance during the mowing season.
6. The charger supplied with this product is intended to be plugged in
such that it is correctly orientated in a vertical or floor mount position.
OPERATION
KNOW YOUR MOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE
OPERATING YOUR MOWER. See "Functional Description" to
familiarize yourself with the location of various controls and adjustments.
Save this manual for future reference.
SAFETY KEY
DANGER : SHARP MOVING BLADE.
In order to prevent accidental start-up or unauthorized use of your
Cordless Mower, a removable safety key J=l has been incorporated into
the design of your mower. The mower wilt be completely disabled when
the Safety Key has been removed from the mower. With the Safety Key
removed, you will have access to the charger receptacle J=3.
NOTE: THE SAFETY KEY HAS A HOLE IN THE CENTER TO ALLOW
FOR STORAGE ON A NAIL, OUT OF THE REACH OF CHILDREN. DO
NOT TETHER SAFETY KEY TO MOWER.
/_ DANGER: ROTATING BLADES CAN CAUSE SERIOUS INJURY.
TO PREVENT SERIOUS INJURY, REMOVE SAFETY KEY WHEN
UNATTENDED, OR WHEN CHARGING, CLEANING, SERVICING,
TRANSPORTING, LIFTING, OR STORING MOWER.
TO TURN MOWER ON
Insert safety key J-1 into the switch housing, until it is fully seated inside housing. The mower is now operational and can be started by activat-
ing the switch lever M=2.
/_ DANGER: SHARP MOVING BLADE. NEVER ATTEMPT TO OVERRIDE THE OPERATION OF THIS SWITCH AND SAFETY KEY
SYSTEM AS SERIOUS INJURY COULD RESULT.
ON=OFF SWITCH (BAIL HANDLE) - FIGURE M
Your mower is equipped with a special on-off switch system. To operate
the system, first push button M-1 on side of switch housing, then pull the
bail handle (switch lever) M=2 to the handlebar M=3. To turn the mower
off, just release the bail handle.
Once the bail handle has returned to the original position it will activate
the "Automatic Braking Mechanism". The motor is electrically braked and
the mower blade wilt stop rotating in 3 seconds or less.
VARIABLE SPEED SELF DRIVE SYSTEM - FIGURE N MODEL: SPCM1936 ONLY
Your SPCM1936 mower is equipped with variable speed self drive. This
system is independent from the blade On-Off switch. It can be used with
or without the blade spinning. For example, when you have completed
cutting your lawn, you can use the self drive to propel the mower back to
your storage location without having the blade motor on.
To operate the system without blade spinning:
1. Insert the safety key.
2. Push the self drive bail handle N=4 to the handlebar N-3.
To turn the self drive off, release the self drive bail handle.
The system has variable speed. You can select the speed by moving the
selector lever N=5.
As you move the selector lever forward, the speed wilt Increase. Moving
the selector lever in a reverse direction, will decrease the speed.
To operate with the blade spinning:
1. Insert the safety key.
2. Push button N=I on side of switch housing, then pull the blade bail
handle N=2to the handlebar N=3.
3. Hold blade bait handle in place against handlebar with right hand. Now
push the self drive bail handle N=4 to the handlebar N=3with your left
hand.
4. You can hold both bait bars simultaneously against the handlebar with your left hand.
When you turn off the self drive, for example at the end of a row, it may become temporarily locked if you pull backwards on the mower. Simply
push ahead slightly and then move the mower as required.
During cutting, at times it may be easier to manoeuver around an object, such as a tree or plants, with the self drive off. The mower can easily
be used with the self drive off.
Z_ WARNING: TO REDUCE THE RISK OF INJURY, NEVER ATTEMPT
TO OVERRIDE THE OPERATION OF THE SWITCH OR SELF DRIVE
SYSTEM. USE THE SELF DRIVE FOR ITS INTENDED PURPOSE ONLY.
MOWER OVERLOAD
To prevent damage due to overload conditions, do not try to remove too
much grass at one time. Stow down your cutting pace, or raise the cut
height. If you have the SPCM1936 model, you can select a lower
self-drive speed to stow the cutting pace.
Your self drive has built-in overload circuit protection. If your mower
self-drive shuts off, release bail handle, wait at least 10 seconds, and try
again.
If you are cutting tall grass, slow the self drive to the lowest speed
position.
MEETS CPSC SAFETY REQUIREMENTS
Black and Decker Mowers conform to the safety standards of the
American National Standards Institute, and the U.S. Consumer Product
Safety Commission. The blade turns when the blade motor is running.
SAFETY SHIELD AND REAR DOOR - FIGURE O
The safety shietd O=1 is designed to minimize the throwing of stones or
other objects by the mower blade backward from under the mower deck.
The shield, along with the rear door O=2, minimizes the possibility of
accidental foot contact with the blade. DO NOT operate mower without
the safety shield and rear door in place.
10
/_ DANGER: Sharp moving blade. Do not operate the mower if the rear door is not closed under spring tension as serious injury could
result.Take your mower to the nearest service center for repair.
FOR MODELS WITHOUT "ON=DEMAND" REMOVING MULCH iNSERT = FIGURE O
To remove the mulch insert O-3 so that you can bag or discharge the grass, follow the steps listed below:
1. Release bail handle to turn mower off, wait until the blade stops and remove safety key.
2. Raise the rear discharge door O-2 and hold it up.
3. Locate your hand in the handle pocket O-4, lift and pull out the mulch
insert O-3 completely.
4. The rear discharge door is spring loaded. When you release it the door
wilt return to the closed position. Ensure the door rests firmly against
the deck.
iNSTALLiNG MULCH iNSERT = FIGURE P
1. Repeat steps 1 and 2 for removing mulch insert.
2. To insert mulch insert P-1, push it until contact is made with the out-
side of the deck. Then lift slightly so that mulch insert rib P-2 is within
deck groove P-3.
3. Release rear door P-4 and ensure it is properly closed.
OPERATING THE MOWER FOR DiSCHARGiNG
To operate the mower in Rear Discharge mode:
1. Remove the grass catcher Q-2 or mulch insert 0-3.
2. Ensure the rear discharge door rests firmly against the deck.
The mower is now in Rear Discharge mode. The cut grass will be
deposited below the closed door exit onto the lawn.
iNSTALLiNG GRASS CATCHER - FIGURE Q, R
1. Release bail handle to turn mower off, wait until the blade stops and
remove safety key.
2. Reaching down between the mower handles, raise the rear discharge
door Q-1 to a vertical position and hold the door up. Ensure that the
mulch insert O-3 has been removed.
3. Pick up the grass catcher Q-2 by the handle Q-3 and place the grass
catcher between the mower handles as shown.
4. Position the grass catcher hanger hooks Q-4 on the mower as
shown in figure R. Release the rear discharge door.
/_ DANGER: Sharp moving blade. Never operate the mower unless
the hanger hooks on the grass catcher are seated properly on the mower
and the rear discharge door rests firmly against the top of the grass
catcher as serious injury could result.
///
11
FOR MODELS WITH "ON-DEMAND"
Your mower may be equipped with the On-Demand feature that allows the conversion of
mulching to bagging or discharging with the turn of a knob.
Release bait handle to turn mower off, wait for the blade to come to a complete stop.
Then remove safety key.
Discharge Mode:
1. Remove grass catcher.
2. Ensure the rear discharge door rests firmly against the deck.
3. Press and turn On-Demand knob so that it is in-line with the word "DISCHARGE" S=I
(see figure S).
Your mower is now in rear discharge mode. The cut grass wilt be deposited below the
closed door exit onto the lawn.
Bagging Mode:
1. Install grass catcher.
2. Ensure rear discharge door rests firmly against the top of the grass catcher.
3. Press and turn On-Demand knob so that it is in-line with the word "BAG" S=1 (see figure S).
Your mower is now in Bagging mode.
Note: To change to rear discharge mode at this point, just remove the grass catcher.
Mulching Mode:
1. To convert to mulch mode press and turn the On-Demand knob so that it is in-line with the
word "MULCH" 1"=2(see figure T). Your mower is now in mulch mode.
Note: If it becomes difficult to rotate the On-Demand knob, it may be necessary to clean out
the deck chute.
1. Release bait handle to turn mower off and wait for the blade to come to a complete stop.
Then remove safety key and battery pack.
2. Hold rear discharge door open, and clean out any debris that may be in the deck chute.
Also clean out deck bottom as necessary.
MOWING TIPS
NOTE: ALWAYS INSPECT AREA WHERE MOWER IS TO BE USED AND REMOVE ALL
STONES, STICKS, WIRE, BONES AND OTHER DEBRIS WHICH MIGHT BE THROWN BY
THE ROTATING BLADE.
1. Mow across the face of slopes, never up-and-down. Exercise extreme caution when changing direction on slopes. Do not mow excessively
steep slopes. Always maintain good footing.
2. Release bail handle to turn mower "OFF" when crossing any gravel area (stones can be thrown by the blade).
3. Set mower at highest cutting height when mowing in rough ground or in tall weeds. Removing too much grass at one time can cause the
motor to be overloaded and to stop. Refer to troubleshooting guide.
4. If a grass catcher is used during the fast growing season, the grass may tend to clog up at the discharge opening. Release bail handle to turn
mower off and remove the safety key. Remove the catcher and shake the grass down to the back end of the bag. Also clean out any grass or
debris which may be packed around the discharge opening. Replace the grass catcher.
5. If mower should start to vibrate abnormally, release bail handle to turn mower off and remove safety key. Check immediately for cause.
Vibration is a warning of trouble. Do not operate mower until a service check has been made. Refer to troubleshooting guide in manual.
6. ALWAYS RELEASE BAIL HANDLE TO TURN MOWER OFF AND REMOVE SAFETY KEY WHEN LEAVING IT UNATTENDED EVEN FOR
A SHORT PERIOD OF TIME.
THE FOLLOWING SUGGESTIONS WILL HELP YOU TO OBTAIN OPTIMUM RUN TIME FROM YOUR CORDLESS MOWER:
1. Slow down in areas where the grass is especially long or thick.
2. When mulching, avoid cutting more than 1-1/2 inches (38mm) off the length at any one time.
3. Avoid mowing when the grass is wet from rain or dew-soaked.
4. Cut your lawn frequently, especially during high growth periods.
NOTE: IT IS RECOMMENDED THAT YOUR MOWER BE RECHARGED AFTER USE TO PROLONG THE BATTERY LIFE. FREQUENT
CHARGING WILL NOT HARM YOUR BATTERY, AND WILL ENSURE THAT THE BATTERY IS FULLY CHARGED AND READY FOR ITS
NEXT USE. STORING BATTERY NOT FULLY CHARGED WILL SHORTEN BATTERY LIFE.
12
MULCHING MOWING TIPS
Your mower was shipped from Black & Decker with the mulch insert installed if not equipped with On-Demand. While mulching, your new mower
is designed to cut the grass clippings into small pieces and distribute them back into the lawn. Under normal conditions, the mulched grass wilt
biodegrade quickly to provide nutrients to the lawn.
Please review the following recommendations for optimum mulching performance.
1. Avoid mowing when the grass is wet from rain or dew. Wet grass may form clumps which interfere with the mulching action and reduce
run-time. The best time to mow grass is in the late afternoon when the grass is dry and the newly cut area will not be exposed to direct
sunlight.
2. For best mulching performance, set the cutting height to remove about one third of the grass blade length, ideally no more than 1-1/2 in. at
one time. If the lawn is overgrown, it may be necessary to increase the cut height to reduce the pushing effort and prevent overloading the
motor. Stow your cutting pace in tall or thick grass conditions. For extremely heavy mulching, it is advisable to first cut at a high cut height set-
ting, and then re-cut to the final cut height. Otherwise, make narrower cuts and mow slowly. ALWAYS MAKE SURE BLADE IS SHARP.
3. For best performance, keep the mower housing free of built-up grass. From time to time release bail handle to turn mower off and wait for the
blade to come to a complete stop. Then remove the safety key and battery pack and turn mower on its side. Using an object such as a stick,
wipe out any accumulation of grass in the blade area. Be careful of the sharp edges of the blade. Clean often in wet, spring grass, and always
after every use.
4. Certain types of grass or grass conditions may require that an area be mulched a second time to fully disperse the grass throughout the lawn.
If cutting a second time, it is advisable to cut perpendicular (across) the first cut pattern. DO NOT CHANGE CUT PATTERN IN ANY WAY
THAT WOULD CAUSE MOWING DOWN A HILL.
5. Change your cutting pattern from week to week. This wilt help 3revent matting of the lawn.
MAINTENANCE
iMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement)
should be performed by BLACK & DECKER Service Centers or other qualified service organizations, always using Black & Decker replacement
parts. When servicing use ONLY IDENTICAL REPLACEMENT PARTS.
REMOVING AND INSTALLING BLADE - FIGURE U
1. RELEASE BAIL HANDLE TO TURN MOWER OFF, WAIT FOR THE BLADE TO
STOP, AND REMOVE SAFETY KEY AND BATTERY PACK.
2. Cut a piece of 2×4 wood U=I (about 2 feet long) (610 mm) to keep blade from turning
while removing flange nut.
3. Turn the mower on its side. Wear gloves and proper eye protection. Be careful of
sharp edges of blade. Position wood U=I and remove flange nut U-3 with 3/4 in.
(19ram) wrench U=2 as shown in figure U.
4. Remove square metal blade spacer V=2, square plastic blade insulator V=3 and
blade V=4as shown in figure V. Examine blade insulator for damage and replace if
necessary.
5. When replacing sharpened or new blade on shoulder of fan V=5, make sure the
"GRASS SIDE" on the blade will be facing the ground when the mower is returned to
its normal upright position. After installing blade V=4, place plastic blade insulator
V-3 on blade such that the raised lips on one side engage the edges of the blade.
Then install the blade spacer V=2so that it sits inside the raised tips on the other
side of the blade insulator. Be sure to align the flats in the hole of the blade spacer
with the flats of the shaft, rotating the blade and blade insulator together as
necessary.
13
6. Position piece of wood W=l to keep blade from turning as shown in figure W. Install
flange nut with the flange against the blade spacer and securely tighten.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A DULL BLADE DOES
NOT CUT GRASS CLEANLY OR MULCH PROPERLY.
USE PROPER EYE PROTECTION WHILE REMOVING, SHARPENING, AND
INSTALLING BLADE. ENSURE THAT SAFETY KEY AND BATTERY PACK IS
REMOVED.
Sharpening the blade twice during a mowing season is usually sufficient under normal
circumstances. Sand causes the blade to dull quickly. If your lawn has sandy soil, more
frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.
WHEN SHARPENING THE BLADE:
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade, removing equal amounts of material from both ends.
TO SHARPEN BLADE IN A VISE:
1. Be sure the bail handle is released, the blade has stopped and safety key and battery
pack removed before removing the blade.
2. Remove blade from mower. See instructions for removing and installing blade.
3. Secure blade X=I in a vise X-2.
4. Wear proper eye protection and gloves and be careful not to cut yourself.
5. Carefully file the cutting edges of the blade with a fine tooth file X=3 or sharpening
stone, maintaining the original cutting edge.
6. Check balance of blade. See instructions for blade balancing.
7. Replace blade on mower and tighten securely.
BLADE BALANCING
Check balance of blade by placing center hole in blade Y=I over a nail or
round shank screwdriver Y-2, clamped horizontally in a vise Y-3. If
either end of the blade rotates downward, file that end. Blade is properly
balanced when neither end drops.
LUBRICATION
No lubrication is necessary. Do not oil the wheels. They have plastic
bearing surfaces which require no lubrication.
CLEANING
Release bait handle to turn mower off, let the blade come to a stop and
then remove safety key and battery pack. Use only mild soap and a
damp cloth to clean the mower. Clean out any clippings which may have
accumulated on the underside of the deck and in discharge chute. After
several uses, check all exposed fasteners for tightness. Ensure that the
mower battery compartment and terminals are kept clear of debris.
PREVENTING CORROSION
Fertilizers and other garden chemicals contain agents which greatly
accelerate the corrosion of metals. If you mow in areas where fertilizers or chemicals have been used, the mower should be cleaned
immediately afterwa,r,d as follows: (1) Release bail handle to turn mower off and remove safety key and battery pack. (2) Wipe all exposed parts
with a damp cloth. ZL_CAUTION: DO NOT POUR OR SPRAY WATER ON THE MOWER IN AN ATTEMPT TO CLEAN IT. Do not store the
lawn mower on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion.
TRANSPORTING AND STORAGE
Z_ DANGER: Rotating blade can cause serious injury. Release bait handle to turn mower off and remove the safety key before lifting,
transporting or storing the mower. Store in a dry place. Note: The mower will not be as heavy to lift if the battery pack is removed first. Do not use
the latch as a lift point for the mower.
/_ WARNING: Mower should not be lifted by the handle when in storage position. Use the metal side plates and deck as grab points.
14
STORAGE POSiTiON
For more compact storing the mower can be stored in an upright position,
with the handle folded over as shown in figure Z. The mower can also
be charged In this upright position.
To place the mower in a convenient storage position:
1. Remove safety key.
2. Hold handle with one hand, pull and rotate one handle quick adjust
knob on mower handle a quarter-turn to release the pin from the
metal plate hole. Handle quick adjust knob will remain in this retract-
ed position. Repeat for the opposite side handle quick adjust knob.
Now the handle is free to move into another handle height position.
3. Swing the handle forward over the front of the mower.
4. Pull and rotate handle quick adjust knobs a quarter-turn to re-
engage pins into metal plate holes. Shake handle slightly to ensure
handle pins are fully engaged in the metal plates.
5. Now the mower can be rotated back onto its rear wheels as shown in
figure Z.
6. Be careful not to pinch power cord when folding and unfolding handle.
CAUTION: If handle is not in locked position in upright storage posi-
tion, the handle may fall back and cause injury or damage. Place blade
side against vertical wall.
CAUTION: Pinch point. To avoid being pinched, keep fingers away
from area between handles when lowering.
OFF-SEASON STORAGE
1. In warmer climates to ensure optimal performance, it is recommended
that the battery be maintained on constant charge.
2. The mower may be stored with the charger disconnected if all of the following conditions are met.
- the battery is fully charged before storing. (Failure to store fully charged wilt shorten battery life).
- the average temperature of the storage location is below 50°F (10°C).
- storage duration is less than 6 months.
BATTERY SERVICE AND INSTALLATION
When service or repair is required, it is recommended that you take your mower to an authorized Black & Decker Service Center.
When servicing or replacing batteries, please note:
• Use only the same type and size of battery as originally supplied.
• Do not dispose of the batteries in a fire. The cell may explode. See Battery Recycling information below.
• Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if
• Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The __
swallowed. _,__, ._,_
battery or conductor may overheat and cause burns.
THE RBRC TM SEAL (BATTERY RECYCLING)
The RBRC TM (Rechargeable Battery Recycling Corporation) Seat on the lead acid battery (or battery pack) indicates that the costs to recycle the
battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent lead acid
batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to
facilitate the collection of spent lead acid batteries. Help protect our environment and conserve natural resources by returning the lead acid
battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery, or call 1-800=544-6986.
Accessories
Recommended accessories for use with your mower are available from your local dealer or authorized service center. If you need assistance
regarding accessories, please call: 1-800-544-6986
Z_ WARNING: The use of any accessory not recommended for use with this lawn mower could be hazardous.
p/n 90564917 MULCH INSERT
pin 242501-05 REPLACEMENT GRASS BAG
MB-1200 REPLACEMENT BLADE
RB-3610 OR RB-3612 BATTERY PACK FOR MODEL CM1936Z.
RB-3612 BATTERY PACK FOR MODEL SPCM1936.
HERE ARE SOME HELPFUL HINTS TO GET THE MOST FROM YOUR BLACK & DECKER CORDLESS MOWER...AND KEEP YOUR LAWN
LOOKING BEAUTIFUL
1. Lawns should first be mowed in the spring when the grass is about 2-1/2 to 3 inches (63mm) to (76mm) high. Mowing too early restricts the
grass root systems which renew themselves every spring. New grass should be mowed when it is about 2-1/2 inches (63mm) high.
2. Do not remove too much grass blade surface at one time...never more than 1/3 of the leaf height during each cutting. Cutting too close
"shocks" sensitive grass blades, resulting in a shallow root system and thus making it more difficult for your lawn to reach water in the soil.
3. Lawn care experts say that excessively close cutting is responsible for much of the difficulty experienced on many lawns. The depth and
strength of the roots of grass are almost exactly proportional to its growth. Grasses of mature lawns often are seriously injured when mowed
shorter than 1-1/2 inches (38mm), and a height of 1-1/2 to 2 inches (38mm) to (51mm) is preferred on large lawns.
15
4. Mowyourlawnwhenitisdrytoavoidclumpingofwetgrass.Ifyouhaveachoice,lateafternoonistheidealtimeformowing,notonly
becausethegrassisdry,butalsobecausethesensitivenewcutareaofthegrasswillnotbeexposedtointensesunlight.
5. Keepthemowingbladesharpforanicecleancut.Thisimprovesthemower'sperformanceandenhancesthelookofyourlawn.Adullblade
shattersandbruisesthetipsofthegrass.Thisimpairsthehealthygrowthofyourlawnandincreasessusceptibilitytoturfdiseases.Ifthe
grasstipsarebruiseditcausesabrownishcolorandgivesyourlawnanunhealthyappearance.Adullblademayalsopullupyoungseedlings.
6. Trytomowyourlawnatthesame(consistent)cuttingheight.Whiletherearetimeswhenyoushouldvarythecuttingheightwiththe
changingseasons,aconsistentcuttingheightproducesahealthier,lovelierlawnwithgenerallyfewerweeds.Mowmorefrequentlyduring
periodsoffastgrowth.Frequentcuttingensuresthatthelower,lessattractiveportionofthegrasswillnotshow.
7. Ifyourlawnhasgrowntoolong,(avacation,forexample,mayinterruptyourcuttingschedule)mowatacuttingheightoneortwopositions
higherthannormal.Asecondpassat"normal"cuttingheightafewdayslaterwiltputyourlawnbackonschedule.Changingthecutting
heightisasimplematterwithBlack&Decker'sOneTouchWheelHeightAdjustment,whichsimultaneouslyadjustsallfourwheelsatonce.
8. Duringthespringandfall,(orafteraninterruptiontothecuttingschedule)thegrasswillbelongerandthicker.Ifthemotorcontinuallyslows
downwhilecutting,trysettingthewheelsforahighercuttingheight.Excessivemotorloadingcanresultinunevencuttingand
quickerdischargeofthebattery.
9. Threegoodideastoenhanceyourlawn'sappearance:Varythemowingdirectionfrequently;mowhorizontallyonhillsides;(thisisalsoa
goodsafetypractice)anddonotforgettooverlapthemowtngpathoneachpass.
10.Alwaysmowgrasssothatclippingsaredischargedontocutlawn.Thiswillkeepyourlawnlookingfreshbyavoiding"CutGrass"build-up
whichwilleventuallybrownandappearugly.Thismethodalsopreservesyourbatterycharge,ensuringyougetthemostfromyourBlack&
DeckerCordlessPowerMower.
11.
During the spring and fall seasons when the grass is longer and thicker, you can use your mower without its battery being fully recharged.
ee reen charge indication light is on). This will enable you to perform short cutting tasks, but we don't recommend this be done frequently.
battery andmower perform much better if charged fully.
TROUBLESHOOTING GUIDE
PROBLEM SOLUTION
1.
2.
3.
Mower doesn't run when bait handle is activated.
Motor stops while mowing.
Mower runs but cutting performance is unsatisfactory,
or does not cut entire lawn.
A. Check to make sure safety key has been installed and is fully seated and
that button on switch housing is being completely depressed.
B. Release bail handle to turn mower off. Remove safety key and battery pack,
turn mower over and check that blade is free to turn.
C. Check that the battery cavity is free of debris and is connected properly.
D. Has battery been fully charged? Plug in charger and wait for green light to
come on.
A. Release bail handle to turn mower off. Remove safety key and battery pack.
Turn mower over and check that blade is free to turn.
B. Raise cutting height of wheels to highest position and start mower.
C. Check that the battery cavity is free of debris and is connected properly.
D. Has battery been fully charged? Plug in charger and wait for green light to
come on.
E. Avoid overloading the mower. Slow down the cutting pace, or raise the cut
height.
A. Has battery been fully charged? Plug in charger and wait for green light to
come on."
B. Release bail handle to turn mower off. Remove safety key and battery pack.
Turn mower over and check:
Blade for sharpness - Keep blade sharp.
Deck and discharge chute for clogging.
C. Wheel height adjustment may be set too low for grass condition. Raise
cutting height.
4. Mower is too hard to push. A. Raise cutting height to reduce deck drag on grass. Check each wheel for
5. Mower is abnormally noisy and vibrates. A. Release bail handle to turn mower off. Remove safety key and battery pack.
free rotation.
Turn mower on side and check blade to ensure it has not been bent or
damaged. If blade is damaged, replace with a Black & Decker
replacement blade. If the underside of the deck is damaged return mower to
a Black & Decker Authorized service center.
B.
If there is no visible damage to the blade and the mower still vibrates the
blade may need to be balanced. See manual for Blade Balancing. If mower
still vibrates after blade is balanced, release bait handle to turn mower off,
remove safety key and battery pack and remove blade. Rotate blade 180
degrees and retighten. If mower still vibrates, return the mower to an
authorized Black & Decker service center.
16
TROUBLESHOOTING
PROBLEM
6.
7.
8.
9. When mulching there are clippings visible.
10. On mower equipped with On Demand -
Battery charger LED's not on. A.
Battery charger LED does not flip to green.
Mower not picking up clippings with bag.
Knob is difficult to adjust into position.
GUIDE (Con't.).
SOLUTION
Check plug connection. Unplug charger, wait a few seconds. Plug charger
in again to see if LED's come on.
B. There are two charge ports on your mower - at the upper handle end and at
the battery pack. The battery pack charge port is accessible only when removed
from the mower. Try both charge ports to see if charger LED's come on.
C. Replace charger.
A. A. Unplug charger and wait a few seconds. Plug in again and leave on
charge for minimum 8 hours.
B. If charger LED is not green, battery may need to be diagnosed. Take to
authorized service center.
A. Chute clogged. Release bait handle to turn mower off. Remove safety key
and battery pack. Clear chute of grass clippings.
B. Too much cut grass. Raise cutting height of wheels to shorten length of the cut.
C. Bag full. Empty bag more often.
A. Too much cut grass. Raise cutting height of wheels to shorten length of the
cut. Do not cut off more than 1/3 of total length.
B. Check blade for sharpness. Always keep blade sharp.
A. Deck chute may be too clogged. Release bail handle to turn mower off.
Remove safety key and battery pack. Clear chute of grass clippings.
11. On mower equipped with Self Drive -
Self Drive performance is erratic.
12. On mower equipped with Self Drive - A. Your Self Drive has built-in overload circuit protection. If your mower self
Self Drive shuts off while using, drive shuts off release bail handle, wait at least 10 seconds, and try again.
A. Self Drive wheel gears may be clogged with debris. Remove wheel hub cap.
B. Using proper wrench size remove wheel bolt, and slide wheel off.
C. Clean debris from within wheel chamber and around gears carefully with a rag.
D. Replace wheel, bolt and hub cap.
f you are cutt ng ta grass, s ow the Se f Drve to the owest speed post on.
NOTE
Should the red light remain on after charging the battery for 24 hours on initial charge, the mower can still be used. The battery may need to be
"conditioned" requiring a few battery charge and discharge cycles before the green indicator light comes on.
THIS IS ONLY A GUIDE INTENDED TO ENABLE YOU TO PERFORM VISUAL CHECKS AND SIMPLE TESTS. SHOULD NONE OF THE
SOLUTIONS PROVIDE SATISFACTION OR IMPROVE PERFORMANCE CALL 1=800=544=6986 (1=800=54=HOW=TO) TO SPEAK TO A
CONSUMER SERVICE REPRESENTATIVE OR TAKE THIS MOWER TO THE CLOSEST AUTHORIZED BLACK & DECKER SERVICE
CENTER FOR SERVICING.
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power toot service. Whether
you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service
location, refer to the yellow page directory under "Tools--Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com
WARRANTIES
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be
replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a
participating retailer). Returns should be made within the time period of the retailer's policy for exchanges (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for
exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our
option. Proof of purchase may be required.Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow
pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to
state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is
not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country specific
warranty information contained in the packaging, call the local company or see the website for warranty information.
Deck Warranty
Lifetime Warranty for DECK only against any defects in material or workmanship.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
17
See 'Tools =
Electric'
- Yellow Pages -
for Service &
Sales
Tondeuses
d_chiqueteuses
avec sac arri_re sans fil
de 483 turn
(19po)
G I ' TILISATIO
Num_ro de catalogue
CM1936Z
Num_ro de catalogue
SPCM1936
Merci d'avoir choisi Black & Decker! Consulter le site Web
www.BiackandDecker.com/NewOwner pour enregistrer votre nouveau produit.
A LIRE AVANT DE RETOURNER CE PRODUIT POUR QUELQUE RAISON QUE CE SOIT •
SidesquestionsoudesproblemessurgissentapresI'achatd'unproduitBlack&Decker,consulterlesiteWeb
HTTP:/N/WW.BLACKANDDECKER.COM/INSTANTANSWERS
pourobtenirdesr@onsesinstantanement24heuresparjour.
Silar@onseestintrouvableouenI'absenced'ac@sa.I'lnternet,composerle1800544-6986de8ha.17h HNE,dulundiauvendredi,pourparleravecun
agent.P@red'avoirlenumerodecataloguesouslamainIorsdeI'appel.
VOlCl DES RENSEIGNEMENTS IMPORTANTS QU'IL VOUS FAUT CONNAiTRE :
oNe pas utiliser la tondeuse si la poignee n'est pas bloquee en position.
oPour une meilleure coupe, maintenir la lame aiguisee et equilibr6e.
oExaminer et nettoyer soigneusement la tondeuse apres chaque utilisation (du gazon adherant au ch&ssis peut reduire le rendement).
oS'assurer que la surface a tondre est a I'ecart de toute personne ou animal de compagnie avant de demarrer la tondeuse et en
cours d'utilisation.
oCharger completement la tondeuse avant la premiere utilisation pour obtenir un rendement optimal. Remettre le bloc-piles & pleine
charge apres chaque utilisation.
18
Loading...