Black & Decker Clma4820l2 Instruction Manual

Page 1
www.blackanddecker.co.uk
2
1
3
5
8
9
4
11
12
10
12
6
7
13
CLMA4820L2
Page 2
A1A2
14
A B
16
16
17
C D
18
4
6
E F
2
19
Page 3
21
5
3
4
G H
23 22
24
25
I K
J
9
8
24
25
20
28
27
26
L M
3
Page 4
6
18 19
19
N O
2
30
29
P Q
R R1
4
Page 5
45
3
6
S T
5
12
12
U
V
32
31
36
35
34
33
W
32
X
5
Page 6
ENGLISH
(Original instructions)
35
38
39
32
33
Y TZ1Z
3540
38
6
6
Page 7
(Original instructions)
ENGLISH
Intended use
Your BLACK+DECKER CLMA4820L2 Autosense lawn mower has been designed for mowing grass. This appliance is intended for consumer use only.
Safety instructions
Warning! When using cordless appli-
ances, basic safety precautions, including the following, should always be followed
to reduce the risk of re, electric shock,
personal injury and material damage. Warning! When using the machine the safety rules must be followed. For your own safety and bystanders please read these instructions before operating the machine. Please keep the instructions safe for later use.
u Read all of this manual carefully before
operating the appliance.
u The intended use is described in this
manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury.
u Retain this manual for future refer-
.
ence
Using your appliance
Always take care when using the appli­ance.
u This appliance is not intended for use
by young or inrm persons without
supervision.
u The appliance is not to be used as a
toy.
u Do not allow children or animals to
come near the work area or touch the appliance or power supply cord.
u Close supervision is necessary when
the appliance is
u Use in a dry location only. Do not allow
the appliance to become wet.
u Do not immerse the appliance in water. u Do not open body casing.
used near children.
There are no user serviceable parts inside.
u Do not operate the appliance in
explosive atmospheres, such as in the
presence of ammable liquids, gases
or dust.
u To reduce the risk of damage to plugs
and cords never pull the cable to remove the plug from a socket.
After use
u When not in use, the appliance should
be stored in a dry, well ventilated place out of the reach of children.
u Children should not have access to
stored appliances.
u When the appliance is stored or trans-
ported in a vehicle it should be placed in the boot or restrained to prevent movement following sudden changes in speed or direction.
Inspection and repairs
u Before use, check the appliance for
damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may af­fect its operation.
u Do not use the appliance if any part is
damaged or defective.
u Have any damaged or defective parts
repaired or replaced by an authorised repair agent.
u Never attempt to remove or replace
any parts other than those specied in
this manual.
u Be careful during adjustment of the
mower to prevent entrapment of the
ngers between moving blades/parts and xed parts of the machine.
u When servicing the blades be aware
that, even though the power source is switched off, the blades can still be
moved.
7
7
Page 8
ENGLISH
(Original instructions)
Additional safety instructions for lawn mowers
u Firmly grip handle with both hands
when operating the lawn mower.
u If at any time it is felt necessary to tilt
the lawn mower, make sure that both hands remain in the operating position while the lawn mower is tilted. Keep both hands in the operating position until the lawn mower is returned to rest correctly on the ground.
u Never wear radio or music head-
phones while operating the lawn mower.
u Never attempt to make a wheel height
adjustment while the motor is running or while the safety key is in the switch housing.
u If the lawn mower stalls, release bail
bar to turn mower off, wait for blade to stop and remove the safety key, before attempting to unclog the chute or remove anything from under the deck.
u Keep hands and feet away from cut-
ting area.
u Keep blades sharp. Always use protec-
tive gloves when handling the lawn mower blade.
u If you are using the grass collector,
check it frequently for wear and dete­rioration. If excessively worn, replace with a new grass collector for your safety.
u Use extreme caution when reversing
or pulling the lawn mower towards you.
u Do not put hands or feet near or under
the lawn mower. Keep clear of the discharger opening at all times.
u Clear the area where the lawn mower
is to be used of objects such as rocks, sticks, wire, toys, bones etc., which could be thrown by the blade.
Objects struck by the blade can cause severe injury to persons. Stay behind the handle when the motor is running.
u Do not operate the lawn mower
barefooted or while wearing sandals. Always wear substantial footwear.
u Do not pull lawn mower backward un-
less absolutely necessary. Always look down and behind before and while moving backward.
u Never direct discharged material
toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Release the bail bar to turn the lawn mower off and stop the blade when crossing gravel surfaces.
u Do not operate the lawn mower
without the entire grass collector, discharge guard, rear guard, or other safety protective devices in place and working. Periodically check all guards and safety protective devices to ensure they are in good working order and will operate properly and perform their intended function. Replace a damaged guard or other safety device before further use.
u Never leave a running lawn mower
unattended. Always remove the safety key if the lawn mower is going to be left unattended.
u Always release the bail bar to stop
the motor and wait until the blade comes to a complete stop and remove the safety key before cleaning the lawn mower, removing the grass bag, unclogging the discharge guard, when leaving the lawn mower, or before making any adjustments, repairs or inspections.
8
Page 9
(Original instructions)
ENGLISH
u Operate lawn mower only in daylight
or good articial light when objects in
the path of the blade are clearly visible from the operating
area of the lawn
mower.
u Do not operate the lawn mower while
under the inuence of alcohol or drugs,
or when your are tired or ill. Always stay alert, watch what you are doing, and use common sense.
u Avoid dangerous environments. Never
operate the lawn mower in damp or wet grass, never use lawn mower in the rain. Always be sure of your foot­ing, walk, never run.
u If the lawn mower should start to
vibrate abnormally, release the bail bar, wait for the blade to stop and remove the safety key, then check for the cause immediately. Vibration is generally a warning of trouble, see the troubleshooting guide for advise in the case of abnormal vibration.
u Always wear proper eye and respira-
tory protection when operating the lawn mower.
u The use of any accessory or attach-
ment not recommended for use with this lawn mower could be hazardous. Only use accessories approved by BLACK+DECKER.
u Never overreach while operating the
lawn mower. Always be sure to keep proper footing and balance at all times while operating the lawn mower.
u Mow across the face of slopes,
never up and down. Exercise extreme caution when changing direction on slopes.
u Watch for holes, ruts, bumps, rocks or
other hidden objects. Uneven terrain could cause a slip and fall accident. Tall grass can hide obstacles.
u Do not mow on wet grass or exces-
sively steep slopes. Poor footing could cause a slip and fall accident.
u Do not mow near drop-offs, ditches,
or embankments. You could lose your footing or balance.
u Always allow the mower to cool down
before storing.
Safety of others
u This appliance is not intended for use
by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
u Children must be supervised to ensure
that they do not play with the appli­ance.
Residual risks.
Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc. Even with the application of the relevant safety regulations and the implementa­tion of safety devices, certain residual risks can not be avoided. These include:
u Injuries caused by touching any rotat-
ing/moving parts.
u Injuries caused when changing any
parts, blades or accessories.
u Injuries caused by prolonged use
of a tool. When using any tool for prolonged periods ensure you take regular breaks.
u Impairment of hearing.
9
Page 10
ENGLISH
(Original instructions)
u Health hazards caused by breathing
dust developed when using your tool (example:- working with wood, espe­cially oak, beech and MDF.)
Warning symbols
The following warning symbols are found on the appliance along with the date code:
Warning! Read the manual prior to operation.
Do not expose the appliance to
R
rain or high humidity.
Beware of sharp blades.
Always remove the safety key before cleaning the lawn mower, removing the grass bag, unclog­ging the discharge guard, when leaving the lawn mower, or before making any adjustments, repairs or inspections.
Beware of ying objects. Keep
bystanders away from the cut­ting area.
F
Wear eye protection
The blades will continue to rotate after the machine is switched off.
Additional safety instructions for batteries and chargers
Batteries
u Never attempt to open for any reason. u Do not expose the battery to water. u Do not expose the battery to heat. u Do not store in locations where the
temperature may exceed 40 °C.
u Charge only at ambient temperatures
between 10 °C and 40 °C.
u Charge only using the charger pro-
vided with the appliance/tool. Using
the wrong charger could result in an electric shock or overheating of the battery.
u When disposing of batteries, follow
the instructions given in the section "Protecting the environment".
u Do not damage/deform the battery
pack either by puncture or impact, as
this may create a risk of injury and re.
u Do not charge damaged batteries. u Under extreme conditions, battery
leakage may occur. When you notice
liquid on the batteries carefully wipe the liquid off using a cloth. Avoid skin
contact.
u In case of skin or eye contact, follow
the instructions below.
Warning! The battery uid may cause
personal injury or damage to property. In case of skin contact, immediately rinse with water. If redness, pain or irritation occurs seek medical attention. In case of eye contact, rinse immediately with clean water and seek medical attention.
Directive 2000/14/EC guaran-
p
aged batteries.
teed sound power.
Chargers
Your charger has been designed for a
specic voltage.
10
Do not attempt to charge dam-
Page 11
(Original instructions)
ENGLISH
Always check that the mains voltage corresponds to the voltage on the rating plate. Warning! Never attempt to replace the charger unit with a regular mains plug.
u Use your BLACK+DECKER charger
only to charge the battery in the appli-
ance/tool with which it was supplied.
Other batteries could burst, causing personal injury and damage.
u Never attempt to charge non-recharge-
able batteries.
u If the supply cord is damaged, it must
be replaced by the manufacturer or an authorised BLACK+DECKER Service Centre in order to avoid a hazard.
u Do not expose the charger to water. u Do not open the charger. u Do not probe the charger. u The appliance/tool/battery must be
placed in a well ventilated area when charging.
$
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insu­lated; therefore no earth wire is
#
required. Always check that the
mains voltage corresponds to the voltage on the rating plate. Never attempt to replace the charger unit with a regular mains plug.
u If the supply cord is damaged, it must
be replaced by the manufacturer or an authorised BLACK+DECKER Service Centre in order to avoid a hazard.
Charging the battery
The battery needs to be charged before rst use and whenev­er it fails to produce sufcient power on jobs that were easily
done before. The battery may become warm while charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures below 10 °C or above 40 °C. Recommended charging tem­perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell temperature is below approximately 10 °C or above 40 °C. The battery should be left in the charger and the charger will begin to charge automatically when the cell tempera­ture warms up or cools down.
u Plug the charger into an appropriate outlet before inserting
the battery pack.
u Insert the battery pack into the charger.
The green LED will ash indicating that the battery is being
charged.
The completion of charge is indicated by the green LED remaining on continuously. The pack is fully charged and may be used at this time or left in the charger
Warning! Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished.
Charger diagnostics
This charger is designed to detect certain problems that can arise with the battery packs or the power source. Problems
are indicated by one LED ashing in different patterns.
Bad Battery
The charger can detect a weak or damaged battery. The red
LED ashes in the pattern indicated on the label. If you see
this bad battery blink pattern, do not continue to charge the battery. Return it to a service centre or a collection site for recycling
Hot/Cold Pack Delay
When the charger detects a battery that is excessively hot or
excessively cold, it automatically starts a Hot/Cold Pack delay,
suspending charging until the battery has normalised.
11
Page 12
ENGLISH
(Original instructions)
After this happens, the charger automatically switches to the Pack Charging mode. This feature ensures maximum
battery life. The red LED ashes in the pattern indicated on the label when the Hot/Cold pack delay is detected.
State of Charge Indicator
The battery is equipped with a state of charge indicator.
This can be used to display the current level of charge in the battery while in the trimmer and during charging. It does not indicate appliance functionality and is subject to variation based on product components, temperature and end user application.
Checking State of Charge during use
u Press the state of charge indicator (A1). u The four LEDs (A2) will illuminate indicating the percent
of charge in the battery (Fig.A.)
u If LED light does not illuminate, charge battery.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely. The charger will keep the battery
pack fresh and fully charged.
Features
This appliance includes some or all of the following features.
1. Switch box
2. Bail handle
3. Upper-handle
4. Lower-handle
5. Upper-handle attachment levers (2)
6. Lower-handle attachment levers (2)
7. Cut height adjust lever
8. Grass collection bag
9. Rear door cover
10. Battery port
11. Battery storage compartment
12. Carrying handles
13. EdgeMax™
Installing and removing the battery pack
(g. B - C)
u depress the battery port cover release button (14) and pull
the battery port cover (15) up to expose the battery port (10) as shown in gure B.
u Slide the battery (16) into the battery port until it is fully
seated and an audible click is heard (gure C). Make sure
battery pack is fully seated and fully latched into position.
u Close the battery port cover. Ensure the cover is fully
latched before starting mower.
To remove battery pack (g. D)
u Open the battery port cover (15). u Depress the battery release button (17) on the battery
pack and pull battery pack out of tool as shown in gure D.
Battery storage
An extra battery can be stored using the battery storage
compartment (11).
u Lift the storage compartment cover and slide the battery
into the compartment as shown in gure E. Battery in this
compartment will not actuate the mower.
u Screw the upper handle quick release clamps (7) through
the lower handle into the clamp nuts (20), With the
upper handle quick release clamps screwed in half way, close the quick release clamps (g. G). If the connection between the handle and quick release clamps is too tight or loose, adjust the depth of the quick release clamps and
close them again until the teeth are fully closed.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the safety key and battery have been removed.
Attaching lower handle (g. F)
u lift lower handle (4) into place making sure the arrow (18)
on the base of the mower lines up with 1, 2, or 3 on the base of the handle (19) (inset of gure F).
Note! Ensure each side of the lower handle is set on the
same number. The arrow must be lined up with 1, 2, or 3 for
operation.
u Close the handle height adjust levers (7) as shown in
gure F. As you close each, make sure the teeth are engaged as shown in gure G.
u If the connection between the handle and lever is too tight
or loose, open the lever and adjust the depth of the lever by turning the lever. Close it again until the teeth are fully clasped and each lever stays securely closed.
Attaching upper handle (g. H)
u Remove the upper-handle attachment levers (5), nuts
(20), and washers (21) from the handle.
u Line up the holes on the bottom of the upper handle (3)
with the holes on the top of the lower handle (4). Note: Make sure the cord is located on the front of both handles. If it is not it may result in the cord tangling and the
inability to easily store the mower (g. I)
u From the outside of the upper handle (3), slide the lever
bolt through the holes.
u Slide the washer over the bolt of the lever and loosely
assemble the entire assembly with the nut.
u Rotate the upper handle into its operating position. u Close the lever. If it is too tight or too loose, open the lever
and the nut to adjust the clamping. Check the levers by
closing them. They should be tight enough so the handles
are held rmly, but loose enough so the levers can be fully
closed. Adjust by opening the lever and turning the nut
until the handles are secured.
Securing the motor cable (g. J)
Warning: Attach cable so that it does not become stretched or pinched in the joints of the handles during use or folding. This can cause damage to the cord.
The motor cable (22) has to be xed to the handles using the
cable restraints (23) that are already attached to the handle to clip the cable to the handle:
12
Page 13
(Original instructions)
ENGLISH
u Place the handles in operating position, see “Attaching
lower handle” section.
u Run the cable up the front of the lower and upper handles. u pull back the cable restraint. u Slide the motor cable under the clip and ensure it is fully
held in place by the restraint.
Bagging
u Ensure the side discharge attachment (27) (g. M) and the
mulching insert (26) (g. L) are removed from the mower
before bagging.
u Lift the rear door cover (9) and place the grass collection
bag (8) onto the mower so the bag hooks (24) rest on the
lugs (25) as shown in gure K. Then lower the rear door
cover.
Mulching
u Ensure the side discharge attachment (27) and the collec-
tion bag (8) are not attached.
u Lift the rear door cover (9) and slide the mulching insert
(26) fully into the mower as shown in gure L.
u ensure the rear door cover fully closes before turning
mower on.
Side discharge
u Ensure the collection bag (8) is removed. u Lift the rear ap (9) and slide the mulching insert (26) fully
into the mower as shown in gure L.
u Lift the side ap (28) and hook side discharge attachment
(27) onto the mower as shown in gure M.
u Release the side ap and ensure the attachment holds in
place before turning mower on as shown in the insert of
gure M.
Operation
Warning! Let the mower work at its own pace. Do not
overload.
Adjusting handle height (fIg. N)
u Open both lower-handle attachment levers (6). u Adjust the handle so the arrow (18) on the base of the
mower lines up with 1, 2, or 3 on the base of the handle (19). ensure the handle is set to the same number on both
sides of the mower.
u Close both levers and ensure the handle is rmly latched.
Adjusting mower height (fIg. O)
The height of cut is adjusted by the central cut height adjust lever, there are 7 positions to choose from. Note: If you are not sure which height to cut, begin mowing with the height adjustment lever (7) in position 7 and adjust
the height down as needed, as shown in gure O.
To set the height of cut:
u Pull the mower height adjustment lever out of the locking
notch.
u Move the lever towards the rear of the appliance to lower
the height of cut.
u Move the lever towards the front of the appliance to raise
the height of cut.
u Push the height adjustment lever into one of the 7 locking
notches.
Safety key
Warning! In order to prevent accidental start-up or unauthor-
ized use of your cordless Mower, a removable safety key (29) has been incorporated into the design of your mower. The mower will be completely disabled when the safety key has been removed from the mower. Note: The safety key has a hole in the centre to allow for storage on a nail, out of the reach of children. Do not tether safety key to mower.
u Insert safety key (29) into the switch housing until it is fully
seated inside housing as shown in gure P. The mower is
now operational.
u Your mower is equipped with a special on-off switch box.
To operate the mower, push the button (30) on the switch
box (1), then pull the bail handle (2) to the handlebar as shown in gure Q.
u To turn the mower off, just release the bail handle.
Warning! Never attempt to lock a switch or bail handle in the on position. Note: Once the bail handle has returned to the original posi­tion it will activate the “Automatic braking Mechanism”. The motor is electrically braked and the mower blade will stop rotating in 3 seconds or less.
Mower overload
To prevent damage due to overload conditions, do not try to remove too much grass at one time. Slow down your cutting pace, or raise the cut height.
EdgeMax™
EdgeMax™ (13) allows you to cut grass right up to the edge of a wall or fence (g. R). EdgeMax™ allows you to accurately cut grass right up to the edge of your lawn (g. R1).
u With the lawn mower parallel to the edge of your lawn,
push the lawn mower along the edge of the lawn. ensure
that the EdgeMax™ is slightly over the edge of your lawn (g. R1).
Note: When the side discharge attachment is attached
EdgeMax™ can only be used on the right side of the mower.
Auto sense
Auto senseTM Technology determines the thickness of grass
TM
Technology
and makes power adjustments accordingly. For thicker grass, the mowers kick into high power while in lighter grass, the mowers lower the power output to conserve battery life and extend runtime
Storage
Warning! Rotating blade can cause serious injury. Release
bail handle (2) to turn mower off, remove safety key, and re­move battery before lifting, transporting, or storing the mower. Store in a dry place.
Warning! To avoid being pinched, keep ngers away from
area between handles when folding down handles. Warning! Make sure cord does not become stretched or pinched in the joints of the handles during folding. This can cause damage to the cord.
The handle of the mower can be easily folded down for quick
and convenient storage.
13
Page 14
ENGLISH
(Original instructions)
u Holding onto the handle, open, but do not remove, the
lower-handle attachment levers (6) and fold the handle to
the front of the mower as shown in gure S.
u Open, but do not remove, the upper-handle attachment
levers (5) and fold the upper handle (3) back over the
lower handle (4) as shown in gure T.
u The mower shold be compacted down as shown in
gure U.
Carrying the mower
u The mower can be carried using the convenient carry
handles (12) as shown in gure V. DO NOT attempt to lift the mower by grasping the upper handle (3) or lower handle (4).
Mowing tips
Warning! Always inspect area where mower is to be used
and remove all stones, sticks, wire, bones, and other debris which might be thrown by the rotating blade. Warning! Mow across the face of slopes, never up-and-down. Exercise extreme caution when changing direction on slopes. Do not mow excessively steep slopes. Always maintain good footing.
u Release bail handle to turn mower “Off” when crossing
any gravel area (stones can be thrown by the blade).
u Set mower at highest cutting height when mowing in rough
ground or in tall weeds. Removing too much grass at one time can cause the motor to be overloaded and to stop. Refer to troubleshooting guide.
u If a grass collection bag (8) is used during the fast growing
season, the grass may tend to clog up at the discharge opening. Release bail handle to turn mower off and remove the safety key. Remove the catcher and shake the grass down to the back end of the bag. Also clean out any grass or debris which may be packed around the discharge opening. Replace the grass catcher.
u If mower should start to vibrate abnormally, release bail
handle to turn mower off and remove safety key. Check immediately for cause. Vibration is a warning of trouble. Do not operate mower until a service check has been made. Refer to troubleshooting guide in manual.
u Always release bail handle to turn mower off and remove
safety key when leaving it unattended even for a short period of time.
Tips for optimum use:
u Slow down in areas where the grass is especially long or
thick.
u Avoid mowing when the grass is wet from rain or dew-
soaked.
u Cut your lawn frequently, especially during high growth
periods.
Note: It is recommended that your mower be recharged after
use to prolong the battery life. Frequent charging will not
harm your battery, and will ensure that the battery is fully charged and ready for its next use. Storing battery not fully charged will shorten battery life.
Removing and installing blade
Warning! When reassembling the blade system, ensure each
part is reinstalled correctly, as described below.
Improper assembly of the blade or other parts of the blade system may cause serious injury. Warning! Release bail handle to turn mower off, wait for the blade to stop, and remove safety key and battery pack.
u Cut a piece of 2x4 wood (31) (about 2 feet long) (610 mm)
to keep blade from turning while removing bolt (32).
u Wear gloves and proper eye protection.
u Turn the mower on its side. Be careful of sharp edges of
blade. Position wood and unscrew bolt with 1/2” wrench (33) as shown in gure W.
u Remove bolt and washer (34). pull off blade (35) as shown
in gure X. The fan (36) should not be removed. Examine
all pieces for damage and replace if necessary.
u The blade can only be attached to the fan in one direction.
To reassemble, line up the d-shaped hole of the blade with the d-shaped post of the fan, ensuring the writing on the blade faces out away from the mower.
u To tighten rmly, position the piece of wood as shown
in gure Y to keep the blade from turning. Slide the bolt
through the washer and screw bolt into place. Tighten with the wrench.
Blade sharpening
Keep blade sharp for best mower performance. A dull blade does not cut grass cleanly. Use proper eye protection while removing, sharpening, and installing blade. Ensure that safety key and battery pack is removed. Sharpening the blade twice during a mowing season is usually
sufcient under normal circumstances. Sand causes the blade to dull quickly. If your lawn has sandy soil, more frequent sharpening may be required.
Note: Replace bent or damaged blade immediately. When sharpening the blade:
u Make sure blade remains balanced. u Sharpen blade at the original cutting angle. u Sharpen cutting edges on both ends of blade, removing
equal amounts of material from both ends.
To sharpen blade in a vise (g. Z)
u Be sure the bail handle is released, the blade has stopped
and safety key and battery pack removed before removing the blade.
u Remove blade from mower. See instructions for removing
and installing blade.
u Secure blade (35) in a vise (38). u Wear proper eye protection and gloves and be careful not
to cut yourself. Carefully le the cutting edges of the blade with a ne tooth le (39) or sharpening stone, maintaining
the angle of the original cutting edge. Check balance of blade. See instructions for blade balancing. Replace blade on mower and tighten securely.
Blade balancing (g. Z1)
Check balance of the blade (35) by placing centre hole in the blade over a nail or round shank screwdriver (40), clamped horizontally in a vise (38). if either end of the blade rotates
downward, le along the sharp edge of that dropping end.
Blade is properly balanced when neither end drops.
Lubrication
No lubrication is necessary. Do not oil the wheels. They have
14
Page 15
(Original instructions)
ENGLISH
plastic bearing surfaces which require no lubrication.
Cleaning
Release bail handle (2) to turn mower off, let the blade come to a stop and then remove safety key. Use only mild soap and a damp cloth to clean the mower. Clean out any clippings which may have accumulated on the underside of the deck. After several uses, check all exposed fasteners for tightness.
Preventing corrosion
Fertilizers and other garden chemicals contain agents which greatly accelerate the corrosion of metals. If you mow in areas where fertilizers or chemicals have been used, the mower should be cleaned immediately afterward as follows: Release bail handle (2) to turn mower off and remove safety key and battery. Wipe all exposed parts with a damp cloth.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory opera-
tion depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool. u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Troubleshooting
If your appliance seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local BLACK+DECKER repair agent. Warning! Before proceeding, release the bail bar to turn mower off, wait for the blade to stop and remove the safety
Problem Possible solution
Mower doesn’t run when bail handle is activated.
Check to make sure safety key has been installed and is fully seated and that button on switch housing is being completely depressed before pulling bail handle.
Release bail handle to turn mower off. Remove safety key and battery pack, turn mower over and check that blade is free to turn.
Has battery been fully charged? Plug in charger and wait for green light to come on
Problem Possible solution
Motor stops while mowing.
Mower runs but cutting performance is unsatis­factory, or does not cut entire lawn.
Mower is too hard to push.
Mower is abnormally noisy and vibrates.
Battery charger LEDs not on.
Mower not picking up clippings with bag.
Release bail handle to turn mower off. Remove safety key and battery pack. Turn mower over and check that blade is free to turn.
Raise cutting height of wheels to highest posi­tion and start mower.
Check that the battery cavity is free of debris and is connected properly.
Has battery been fully charged? Press state of charge button.
Avoid overloading the mower. Slow down the cutting pace, or raise the cut height.
Has battery been fully charged? Press state of charge button.
Release bail handle to turn mower off. Remove safety key and battery pack. Turn mower over and check:
u Blade for sharpness - Keep blade sharp. u Deck and discharge chute for clogging.
Wheel height adjustment may be set too low for grass condition. Raise cutting height.
Release bail handle to turn mower off. Remove safety key and battery pack. Raise cutting height to reduce deck drag on grass. Check each wheel for free rotation
Release bail handle to turn mower off. Remove safety key and battery pack. Turn mower on side and check blade to ensure it has not been bent or damaged. If blade is damaged, replace with a BLACK+DECKER replacement blade. If the underside of the deck is damaged, return mower to a BLACK+DECKER Authorized service center.
If there is no visible damage to the blade and the mower still vibrates:
u Release bail handle to turn mower off. u Remove safety key and battery pack. u Disassemble entire blade assembly as
described in the “Removing and installing blade” section.
u Remove any debris and clean each
piece.
u Replace each piece as described in the
“Removing and installing blade” section.
If mower still vibrates, return the mower to an authorized BLACK+DECKER authorized service center.
Check plug connection.
Replace charger.
Chute clogged. Release bail handle to turn mower off. Remove safety key and battery pack. Clear chute of grass clippings.
Raise cutting height of wheels to shorten length of the cut.
Bag full. Empty bag more often.
Protecting the environment
Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste.
Z
15
Page 16
ENGLISH
(Original instructions)
Products and batteries contain materials that can be recovered or recycled, reducing demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com
Technical data
CLMA4820L2
Input Voltage
No-Load Speed
Weight
Battery
Voltage
Capacity Ah
Type
Charger
Input Voltage
Output Voltage
Current mA
Approx. charge time
VDC36V
-1
min
2900
kg
net weight 21.24KG gross 25.95KG
90624732
V
36V
DC
2Ah
Li-Ion
90616337-01
V
230V
AC
V
36V
DC
1350 mA or 1.35A
h
90 mins
Hand/arm weighted vibration value:
= < 0,5 m/s2 , uncertainty (K) = 1,5 m/s2.
LPA (sound preasure) 80 dB(A)
uncertainty (K) = 3 dB(A)
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
These products also comply with directive 2004/108/EC and
2011/65/EU. For more information, please contact Black &
Decker at the following address or refer to the back of the
manual.
The undersigned is responsible for compilation of the technical
le and makes this declaration on behalf of Black & Decker.
R. Laverick
Director of Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
09/09/2015
Guarantee
Black & Decker is condent of the quality of its products
and offers consumers a 24 month guarantee from the date of purchase. This guarantee is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance with Black&Decker Terms and Conditions and you will need to submit proof of purchase to the seller or an authorised repair agent. Terms and conditions of the Black&Decker 2 year guarantee and the location of your nearest authorised repair agent can be obtained on the Internet at www.2helpU.com, or
by contacting your local Black & Decker ofce at the address
indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and receive updates on new products and special offers.
%
CLMA4820L2 Autosense lawn mower
Black & Decker declares that these products described under
Level of accoustic power according to 2000/14/EC (Article 12,
16
"technical data" are in compliance with:
2006/42/EC, EN 60335-1, EN 60335-2-77:2010
2000/14/EC, Lawn Mower, L < 50cm, Annex VI,
DEKRA Certication B.V., Utrechtseweg 310, ED Arnhem
Netherlands
Notied Body ID No.: 0344
Annex III, L ≤ 50 cm):
LWA (measured sound power) 93 dB(A)
uncertainty (K) = 3 dB(A)
LWA (guaranteed sound power) 96 dB(A)
Page 17
(Original instructions)
ENGLISH
17
Page 18
ENGLISH
(Original instructions)
18
18
Page 19
(Original instructions)
ENGLISH
19
19
Page 20
90629771 REV-0
Australia Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100 20 Fletcher Road, Mooroolbark, Fax 03-9727 5940 Victoria, 3138
New Zealand Black & Decker Tel. +64 9 259 1133 5 Te Apunga Place Fax +64 9 259 1122 Mt Wellington Aukland 1060
United Kingdom & Black & Decker Tel. 01753 511234 Republic Of Ireland 210 Bath Road Fax 01753 512365
www.blackanddecker.co.uk Slough, Berkshire SL1 3YD emeaservice@sbdinc.com
11/2015
Loading...