Black & Decker Bx250 Instruction Manual [ar]

BX250 Blender

First Use Safety Recommendation

Please read through this booklet for safe and efficient use of the appliance. We urge you to read the "Do's & Don'ts" section and also follow all detailed instructions even if you are familiar with a similar appliance.

Keep this guide handy for future reference.

BX250

IMPORTANT SAFEGUARDS

While using electrical appliances, in order to reduce the risk of fire, electric shock, and / or injury to persons, basic safety precautions should be followed, including the following:

• Read all instructions carefully, even if you are familiar with the appliance.

• To protect against the risk of electric shock, DO NOT IMMERSE the appliance,

cord set or plug in water or other liquids.

• To clean, wipe the exterior with a damp cloth.

• Close supervision is necessary when any appliance is used near children. Do not allow children or any person unfamiliar with these instructions use this appliance. Never leave an appliance unattended when in use.

• Switch off and remove the plug from the power outlet when not in use, before assembling or disassembling parts, cleaning or carrying out any maintenance of the appliance. Never pull the cord while unplugging out from power outlet.

• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or is dropped or damaged in any manner. Return the complete appliance to your nearest authorized service facility for examination, electrical repair, mechanical repair or adjustment to avoid any hazard.

• The use of attachments or accessories not recommended or sold by this appliance manufacturer may result in fire, electric shock or personal injury.

• Do not let the cord hang over the edge of a table, counter, or touch hot surfaces.

• Avoid touching hot surfaces, use handles and knobs.

• Do not operate or place any part of this appliance on or near any hot surfaces (such as gas or electric burner or in a heated oven).

• Do not abuse the cord. Never carry the appliance by the cord or yank it to disconnect it from the outlet; instead, grasp the plug and pull to disconnect.

• When using an extension cord with your appliance, make sure the extension cord is correctly wired, and rated for its use.

• This product is intended for household use only.

• Do not attempt to repair the appliance yourself; instead, take it to your Black & Decker-owned or Authorized Service Centre for repair.

• Care should be taken when handling slicing discs & blade, especially when removing them from the holders and during cleaning.

• Keep children and animals away from the appliance and cord set.

SAVE THESE INSTRUCTIONS

Parts Identification

1. Motor Unit

2. Speed Switch

3. Power Cord

4. Blade Assembly

5. Blending Jar

6. Jar Lid

7. Measuring cup

8. Grinder jar - 2 nos.

9. Grinder blade assembly

10. Cheese blade assembly

Product Features

350W of motor power to take care of toughest grinding needs Cord storage to reduce clutter Non slip rubber feet for a firmer grip of product on standing platform.

1.5 lt transparent jar for meeting your daily requirements

70 gms Dry Grinder & Cheese Grater unit for meeting all your small dry grinding & cheese grating

requirements.

How to use your Blender :-

Your blender is designed for indoor household blending and grinding operations only.

• Remove all the packaging from the product.

• Wash the jar, lid, measuring cup and blade assembly in warm sudsy water and dry it thoroughly.

• Ensure that the rated voltage on your appliance is the same as the line voltage in the socket you

will be using to operate your blender.

• Your blade assembly has a sealing ring, which can be removed while cleaning and

should be replaced immediately to prevent damage and loss. (figure A)

• Now take the blade assembly with the sealing ring in place and rotate it

Fig. A

anticlockwise lock it in place at the bottom of the blender jar. (figure B)

• Place the assembled jar on the main unit with the handle positioned on the

right side of the unit as shown in the figure C.

Fig. B

• Put your ingredients into the jar before plugging it into the power supply.

• Place the lid on the jar and rotate it clockwise to lock it in position. The lid

will also operate the safety switch which will make the unit operational.

Fig. C

NOTE: Unless the lid is in the locked position the unit will not work.

• Select the desired speed to mix and blend the ingredients in the jar.

• Turn the Knob to "0" position and wait until blades have stopped before removing the jar.

NOTE : Never run the blender continuously for more than 2 minutes in a stretch. Turn off as soon as the right consistency is reached. If you want to continue operating the blender, allow a rest of not less than 1 minute between operating cycles.

How to use your Dry Grinding / Cheese Grating Mill

• Make sure that the switch is in the off position.

• Place the ingredients in the grinder Jar (figure D)

• Tighten the grinder blade / cheese blade assembly

(ensure that the sealing ring is in place) onto the grinder jar by rotating it anticlockwise. (figure E)

• Assemble the mill assembly onto the main unit by locking

it in position by rotating it anticlockwise. (figure F)

• Use the pulse operation 2~3 times initially to mix the ingredients.

• Now select the speed till the desired consistency is achieved.

• When the grinding / grating is finished turn the speed knob to "0" position and wait till the

blade comes to complete stop.

• Remove the mill assembly from the main unit by rotating it clockwise.

• Hold the mill assembly as shown in figure D, rotate the blade assembly clockwise & lift it

from the jar. You can then pour the contents out.

NOTE:

- Never use the mill assembly for more than 30seconds without interruption. Allow the

Fig. E

Fig. D

Fig. F

grinder to cool down for at least one minute between two consecutive operating cycles.

- Never forget to place the sealing ring in the grinder blade assembly (figure G). If it is not present or damaged, it will cause leakage of ingredients during usage.

- Your mill is meant for grinding small quantities of dry ingredients.

- Never use the grinder to grind very hard ingredients such as nutmeg, turmeric etc.

- The Grinding mill cover will get discoloured when the grinder is used to process ingredients such as cloves, anise etc.

Control Panel

1. Position "0" - the unit does not operate, and it is in OFF position.

2. Position "P"- the unit will operate at high speed as long as the knob is held in this position. (figure H)

3. Position "1" - the blender works at low speed.

4. Position "2" - the blender works at high speed.

To Crush Ice

Fig. H

Fig. G

• Liquid must be used to crush ice.

• To make frozen drinks, fill the jar with liquid upto desired level ( max half the jar capacity) and then put in ice cubes ( the max size of diced ice cubes should be not more than 2cms).

• Blend / crush the content till desired consistency is achieved, then turn the knob to the "0"position.

NOTE : Do not crush ice without liquid.

+ 8 hidden pages