Black & Decker BEMW471ES, BEMW481ES, BEMW461ES User guide

Download

Page 1

1 22 55

www.blackanddecker.co.uk

BEMW461ES BEMW471ES BEMW481ES

Page 2

14a

14b

14c

14d

A B

14b 14c

14a 14c14b

14b

14a

14c

14d

Page 3

8 7

14g

14f

Page 4

ENGLISH

(Original instructions)

N O1

Page 5

(Original instructions)

ENGLISH

1817

2120

22 23

Page 6

ENGLISH

(Original instructions)

Intended use

Your BLACK+DECKER BEMW461ES, BEMW471ES, BEMW481ES lawn mowers have been designed for mowing grass. These appliances are intended for consumer use only.

Safety instructions

Warning! When using mains-powered

appliances, basic safety precautions, including the following, should always be

followed to reduce the risk of re, electric

shock and personal injury.

u Read all of this manual carefully before

using the appliance.

u The intended use is described in this

manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury.

u Retain this manual for future

reference.

Training

u Read the instructions carefully. Be

familiar with the controls and the proper use of the appliance.

u Never allow children or people

unfamiliar with these instructions to use the machine. Local regulations can restrict the age of the operator.

u Never operate the machine while

people, especially children, or pets are nearby.

u Keep in mind that the operator or user

is responsible for accidents or hazards occurring to other people or their

property.

Preparation

u While operating the machine always

wear substantial footwear and long trousers. Do not operate the machine when barefoot or wearing open sandals. Avoid wearing clothing that is loose

tting or that has hanging cords or ties.

u Thoroughly inspect the area where the

machine is to be used and remove all objects which can be thrown by the

machine.

u Before using, always visually inspect

to see that the blade, blade bolt and the blade assembly are not worn or

damaged. Replace worn or damaged

components in sets to preserve balance. Replace damaged or unreadable

labels.

u Before use check the supply and

extension cord for signs of damage or aging. If the cord becomes damaged during use, disconnect the cord from the supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the machine if the cord is damaged or worn.

u Wear safety glasses or goggles when

operating this tool. Use a face or dust mask whenever the operations take place in dusty surroundings. Hearing protection should be worn whenever the sound level seems uncomfortable.

u Guard against electric shock.

Page 7

(Original instructions)

ENGLISH

Prevent body contact with earthed or grounded surfaces (e.g. metal railings, lampposts, etc.).

Operation

u Never operate the appliance with

defective guards or shields, or without

safety devices, for example deectors

and/or grass catchers, in place.

u Only use the appliance in daylight or

good articial light.

u Do not expose the appliance to rain.

Do not use the appliance in damp or wet conditions. Preferably do not use the appliance in wet grass.

u Be sure of your footing, particularly on

slopes. Be aware that freshly cut grass is damp and slippery. Do not work on

steep slopes.

u Work across the face of slopes, never

up and down. Take extreme caution when changing direction on slopes.

u Do not mow excessively steep slopes. u Walk, never run when using the

appliance. Do not pull the appliance towards you or walk backwards when using the appliance.

u Switch on the appliance according to

instructions and with your feet well away from the blade.

u Do not start the machine when

standing in front of the discharge opening.

u Do not tilt appliance when switching it

on, except if the appliance has to be tilted for starting.

In that case, do not tilt the appliance more than absolutely necessary and lift only the part that is away from the operator. Always ensure that both hands are in the operating position before returning the appliance to the ground.

u Switch off the appliance and wait for

the blade assembly to stop running if the appliance has to be tilted for transportation when crossing surfaces other than grass, and when transporting the appliance to and from the area to be mowed.

u Do not lift or carry the appliance until

the blade has come to a complete standstill.

u Keep your hands and feet well away

from the blade.

u Do not put your hands or feet near or

under rotating parts.

u Keep away from discharge openings at

all times.

u Switch off, remove the plug from

the socket and ensure that moving parts have stopped rotating before leaving the appliance unattended and before changing, cleaning or inspecting any parts of the appliance or clearing a blockage. After striking a foreign object. Inspect the machine for damage and make repairs before restarting and operating the machine;

u If the appliance starts to vibrate

abnormally or if you hit a foreign object, switch the appliance off and remove the plug from the socket.

Page 8

ENGLISH

(Original instructions)

Check for any damage to the appliance, replace or repair any damaged parts, check for and tighten any loose parts.

u Take care to keep the mains cable

away from the blade. Always be aware of the position of the cable.

u The motor will continue to run for a few

seconds after switching the appliance off. Never attempt to force the blade to come to a standstill.

Maintenance and storage

u Before use, check the appliance for

damaged or defective parts. Check for misalignment and seizure of moving parts, breakage of parts, damage to guards and switches and any other conditions that may affect its operation. Ensure that the appliance will operate properly and perform its intended function. Never use the appliance when any guard or enclosure is damaged or not in place. Do not use the appliance if any part is damaged or defective. Do not use the appliance if the switch does not turn it on and off.

Have any damaged or defective parts

repaired or replaced by an authorised repair agent.

u Check the cable frequently for

damage. If the cable is damaged, it must be replaced by an authorised repair agent in order to prevent a hazard. Inspect extension cables periodically. Replace a damaged extension cable immediately.

u Keep all nuts, bolts and screws on

the appliance tight to ensure a safe working condition.

u Check the grass collector for wear or

damage and replace it if necessary. Never use the appliance without the grass collector.

u Be careful during adjustment of the

machine to prevent entrapment of the

ngers between moving blades and

xed parts of the machine.

u When servicing the blades be aware

that, even though the power source is switched off, the blades can still be

moved.

u When not in use, the appliance should

be stored in a dry place. Children should not have access to stored appliances.

u Always allow the machine to cool

down before storing.

u Ensure that only replacement cutting

means of the right type are used.

u Use only BLACK+DECKER

recommended spare parts and accessories.

Additional safety instructions for Lawnmowers

u Always use an approved extension

cable suitable for the power input of this tool (see technical data). The extensioncable must be suitable for outdoor use and marked accordingly. Up to 30 m of 1.5 mm2 HO5VV-F extension cable can be used without loss of product performance.

Page 9

(Original instructions)

ENGLISH

Before use, inspect the extension cable for signs of damage, wear and ageing. Replace the extension cable if damaged or defective. When using a cable reel, always unwind the cable completely.

u Do not transport the machine while the

power source is running

u Firmly grip handle with both hands

when operating the lawn mower.

u If at any time it is felt necessary to tilt

the lawn mower, make sure that both hands remain in the operating position while the lawn mower is tilted. Keep both hands in the operating position until the lawn mower is returned to rest correctly on the ground.

u Never wear radio or music

headphones while operating the lawn mower.

u Never attempt to make a wheel height

adjustment while the motor is running or while the safety key is in the switch housing.

u If the lawn mower stalls, turn mower

off, wait for blade to stop, before attempting to unclog the chute or remove anything from under the deck.

u Keep hands and feet away from

cutting area.

u Keep blades sharp.

Always use protective gloves when handling the lawn mower blade.

u If you are using the grass collector,

check it frequently for wear and deterioration. If excessively worn, replace with a new grass collector for your safety.

u Use extreme caution when reversing

or pulling the lawn mower towards you.

u Do not put hands or feet near or under

the lawn mower. Keep clear of the discharger opening at all times.

u Clear the area where the lawn mower

is to be used of objects such as rocks, sticks, wire, toys, bones etc., which could be thrown by the blade. Objects struck by the blade can cause severe injury to persons. Stay behind the handle when the motor is running.

u Do not operate the lawn mower

barefooted or while wearing sandals. Always wear substantial footwear.

u Do not pull lawn mower backward

unless absolutely necessary. Always look down and behind before and while moving backward.

u Never direct discharged material

toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Release the start handle to turn the lawn mower off and stop the blade when crossing gravel surfaces.

u Do not operate the lawn mower

without the entire grass collector, discharge guard, rear guard, or other safety protective devices in place and working. Periodically check all guards and safety protective devices to ensure they are in good working order and will operate properly and perform their intended function.

Page 10

ENGLISH

(Original instructions)

Replace a damaged guard or other safety device before further use.

u Never leave a running lawn mower

unattended.

u Always release the bail bar to stop the

motor and wait until the blade comes to a complete stop before cleaning the lawn mower, removing the grass bag, unclogging the discharge guard, when leaving the lawn mower, or before making any adjustments, repairs or inspections.

u Operate lawn mower only in daylight

or good articial light when objects in

the path of the blade are clearly visible from the operating area of the lawn mower.

u Do not operate the lawn mower while

under the inuence of alcohol or drugs,

or when your are tired or ill. Always stay alert, watch what you are doing, and use common sense.

u Avoid dangerous environments.

Never operate the lawn mower in damp or wet grass, never use lawn mower in the rain. Always be sure of your footing, walk, never run.

u If the lawn mower should start to

vibrate abnormally, release the on/off switch, wait for the blade to stop and then check for the cause immediately. Vibration is generally a warning of trouble, see the troubleshooting guide for advise in the case of abnormal vibration.

u Always wear proper eye and

respiratory protection when operating the lawn mower.

u The use of any accessory or

attachment not recommended for use with this lawn mower could be hazardous. Only use accessories approved by BLACK+DECKER.

u Never overreach while operating the

lawn mower. Always be sure to keep proper footing and balance at all times while operating the lawn mower.

u Mow across the face of slopes, never

up and down. Exercise extreme caution when changing direction on slopes.

u Watch for holes, ruts, bumps, rocks or

other hidden objects. Uneven terrain could cause a slip and fall accident. Tall grass can hide obstacles.

u Do not mow on wet grass or

excessively steep slopes. Poor footing could cause a slip and fall accident.

u Do not mow near drop-offs, ditches, or

embankments. You could lose your footing or balance.

u Always allow the mower to cool down

before storing. Pull the plug from the socket and pull the battery pack from the machine. Make sure that all moving parts have come to a complete stop:

u Whenever you leave the machine; u Before clearing a blockage; u Before checking, cleaning or working

on the appliance.

Page 11

(Original instructions)

ENGLISH

Vibration

The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN50636 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated. When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. Do not operate the tool if the vibration registers as abnormal.

Safety of others

u This appliance is not intended for use

by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

Unless they have been given

supervision or instruction concerning

use of the appliance by a person

responsible for their safety.

u Children must be supervised to

ensure that they do not play with the

appliance.

u After striking a foreign object. Inspect

the appliance for damage and make

repairs as necessary.

Residual risks

Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc. Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include:

u Injuries caused by touching any

moving parts.

u Injuries caused by touching any hot

parts.

u Injuries caused when changing any

parts or accessories.

u Injuries caused by prolonged use

of the appliance. When using any

appliance for prolonged periods

ensure you take regular breaks.

u Impairment of hearing. u Health hazards caused by breathing

dust developed when using your

tool (example:- working with wood,

especially oak, beech and MDF.)

Page 12

ENGLISH

(Original instructions)

u If operating the mower in a damp

location is unavoidable, use a residual current device (RCD) with a tripping current of not more than 30 mA. Use of an RCD reduces the risk of electric shock.

u Never pick up or carry an appliance

while the motor is running.

Warning symbols

The following warning symbols are found on the appliance along with the date code:

Warning! Read the manual prior to operation.

Do not expose the appliance to rain or high humidity.

Always remove the plug from the socket before inspecting a damaged cable. Be careful not to use your appliance if the cable is damaged.

Beware of sharp blades.

Beware of ying objects. Keep

bystanders away from the cutting area.

Keep the cable away from the cutting blades.

Directive 2000/14/EC guaranteed sound power

Electrical safety

Warning! This tool is double

insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must

be replaced by the manufacturer or an

authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

u Electric safety can be further improved

by using a high sensitivity 30 mA

Residual Current Device (RCD).

Features

This appliance includes some or all of the following features.

1. Power button

2. Comfort grip handles

3. On/off switches

4. EasySteer pivot control

5. EasySteer pivot control buttons

6. Upper handle

7. Handle knobs

8. Cable management system (BEMW471ES, BEMW481ES

units only)

9. Lower handle

10. Back ap

11. Carrying handles

12. Height adjustment gauge

13. Height adjustment lever

14. Grass box

14. Grass box handle

The blades will continue to rotate after the machine is

Assembly

Warning! Before assembly, make sure that the appliance is

switched off and unplugged.

switched off.

Page 13

(Original instructions)

ENGLISH

Assembling the grass collection box (g. A, B, C, D

and E)

The grass box requires assembly before use and comes in 5 pieces.

u Clip the handle (15) into the lid (14a) of the grass box

(g. B). The handle will only t one way round.

u Clip the 2 sides (14b) and (14c) of the grass collection box

together. Make sure that all clips and guides are aligned

(g. C).

u Align the lid (14a) onto the assembled grass collection

box. Ensure that the 10 guides are aligned (g. D)

u Align the assembled sides onto the bottom (14d) of the

grass collection box. Ensure that the 4 guides are

aligned (g. E)

u Push the 2 parts together. Apply even force around all

edges of the grass collection box securing the clips into position uniformly. Check that each clip is fastened together securely.

Fitting the lower handle (g. F)

u Insert the ends of the lower handles (9) into the

corresponding holes in the mower.

u Press the handle down as far as it will go. u Secure the handle using the screws.

Assembling the upper handle (g. G)

u Fit the upper handle part to the lower handle using the

handle knobs (7) , washers and screws as shown.

Securing the motor cable (g. H)

u The motor cable has to be xed using the cable restraint. u Snap a restraint clip (16) around the cable and lower

handle about 150mm below the handle knob (7).

Fitting the grass collection box (g. I)

u Lift the ap (10) and place the grass collection box (14)

ensuring the recesses (14f) t over the lugs (14g).

Proper Hand Position (Fig. J)

Warning! To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown. Warning!: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction. Proper hand position requires one hand on each of the comfort grip handles (2).

(Fig. J1)

EasySteer Innovation - The innovative handle design easily moves from left to right at the push of a button, giving you precision control and manouvrability around your garden.

Adjusting the height of cut (g. K)

The height of cut is adjusted by the central height adjust mechanism, there are 6 positions to choose from.

u Pull the height adjustment lever (13) away from the body

of the unit.

u Move the lever towards the rear of the appliance to

lower the height of cut.

u Move the lever towards the front of the appliance to

raise the height of cut.

u Push the height adjustment lever into one of the 6

height locations. NOTE: The height of cut can be viewed on the height of cut gauge (12) on the side of the unit.

Switching on and off (g. M)

Switching on

u Push the power button (1).

u Pull the left or right ON/OFF switch (3) towards the handle.

Switching off

u Release ON/OFF switches (3).

Warning! Never attempt to lock a switch in the on position.

Mowing (g. N, O1 & O2)

We recommend to use your mower as outlined in this section in order to achieve optimum results and to reduce the risk of cutting the mains cable.

u Loop the extension cord through the cable

management system (5) (BEMW471ES, BEMW481ES

units only) as shown (Fig. N). Ensure you

leave approximately 100 of cord between the power

switch (1) and the cable management system.

u Ensure that the cable management system

(BEMW471ES, BEMW481ES GB units only) can slide

freely from one side to the other.

u Place the bulk of the mains cable on the lawn, close to the

starting point (position 1 in g. O1).

u Switch the appliance on as described above.

u Proceed as shown in g. O1

u Move from position 1 to position 2.

u Turn right and proceed towards position 3. The cable

management system will slide from one side to the other, ensuring the extension cord is kept away from the cutting blade.

u Turn left and move towards position 4.

u Repeat the above procedure as required.

Warning! Do not work towards the cable as shown in g. O2.

Up to edge cutting (g. P, Q)

Up to edge cutting allows you to cut grass right up to the edge

of a wall or fence (g P).

Up to edge cutting allows you to accurately cut grass right up

to the edge of your lawn (g Q).

Page 14

ENGLISH

(Original instructions)

u With the lawnmower parallel with the edge of your lawn,

push the lawnmower along the edge of the lawn. Ensure that the edge of the mower is slightly over the edge of

your lawn (g.Q).

Cable tidy (g. R)

u Cable tidy, stores cable when not in use. Only available on

BEMW471ES & BEMW481ES GB units.

Removing Blade (Fig. S, T)

Note: BEMW461ES / BEMW471ES & BEMW481ES all use new winged blades which improves collection vs previous range of mowers. Blade accessories Cat # 34cm A6320 38cm A6321 42cm A6322. Warning! Ensure the blade has completely stopped and disconnect the mower from the power source.

u Cut a piece of 2x4 wood (17) 305mm to keep blade from

turning while removing ange nut.

u Turn the appliance onto its side. Wear gloves and proper

eye protection. Be careful of sharp edges of blade.

u Position piece of wood (17) to keep blade from turning

as shown in Fig. S.

u Use a 14mm wrench (19) to loosen and remove the

blade bolt by turning counterclockwise.

u Pull off blade (18), blade insulator (20), as shown in

Fig. T. Examine all pieces for damage and replace if necessary.

Installing Blade (Fig. U)

u Place blade insulator (20) then the blade (18) onto bolt

shaft with the lettering on the blade facing out, and place the blade bolt (21) onto the bolt shaft.

u Tighten the blade bolt as rmly as possible by hand. u Position piece of wood (17) to keep blade from turning

as shown in Fig. U.

u Use a 14mm wrench to securely tighten the blade

bolt by turning the wrench clockwise.

Blade sharpening

Keep blade sharp for best mower performance. A dull blade does not cut grass cleanly. Use proper eye protection while removing, sharpening, and installing blade. Sharpening the

blade twice during a mowing season is usually sufcient under

normal circumstances. Sand causes the blade to dull quickly. If your lawn has sandy soil, more frequent sharpening may be required. Note: Replace bent or damaged blade immediately. When sharpening the blade:

u Make sure blade remains balanced. u Sharpen blade at the original cutting angle. u Sharpen cutting edges on both ends of blade, removing

equal amounts of material from both ends.

To sharpen blade in a vice (g. V)

u Be sure the blade has stopped and the mower is

unplugged before removing the blade.

u Remove blade from mower. See instructions for removing

and installing blade.

u Secure blade (18) in a vice (22).

u Wear proper eye protection and gloves and be careful not

to cut yourself.

Carefully le the cutting edges of the blade with a ne tooth le (23) or sharpening stone, maintaining the angle

of the original cutting edge. Check balance of blade. See instructions for blade balancing.

u Replace blade on mower and tighten securely.

Blade balancing (g. W)

Check balance of the blade (18) by placing centre hole in the blade over a nail or round shank screwdriver, clamped horizontally in a vice. If either end of the blade rotates

downward, le along the sharp edge of that dropping end.

Blade is properly balanced when neither end drops.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have plastic bearing surfaces which require no lubrication.

Cleaning

Turn the mower off and let the blade come to a stop. Use only mild soap and a damp cloth to clean the mower. Clean out any clippings which may have accumulated on the underside of the deck. After several uses, check all exposed fasteners for tightness.

Preventing corrosion

Fertilizers and other garden chemicals contain agents which greatly accelerate the corrosion of metals. If you mow in areas where fertilizers or chemicals have been used, the mower should be cleaned immediately afterward as follows: Turn the mower off and unplug mower. Wipe all exposed parts with a damp cloth.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool/appliance care and regular cleaning. Warning! Before performing any maintenance on corded/ cordless power tools:

u Switch off and unplug the appliance/tool.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it.

Page 15

(Original instructions)

ENGLISH

Your charger does not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Troubleshooting

If your appliance seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local BLACK+DECKER repair agent. Warning! Before proceeding, release the bail bar to turn mower off and wait for the blade to stop.

Problem Possible cause Possible solution

Mower will

not start.

Machine functions intermit-

tently.

Machine leaves ragged

nish or motor labours.

Cord is not plugged in.

Circuit fuse is blown.

Plug mower into a working outlet.

Replace circuit fuse. (If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have itserviced by an authorised BLACK+DECKER service center.

Cord or switch is damaged.

Have cord or switch replaced at an authorised BLACK+DECKER service center.

Grass too long. Increase the height of

cut and move machine to shorter grass to start.

Thermal cut out activated.

Height of cut

Allow motor to cool and increase height of cut.

Increase height of cut.

too low. Cutting blade

Replace the blade.

blunt. Underside

of machine clogged.

Check underneath the machine and clear out as necessary (always wear heavy duty gloves)

Blade tted

Ret blade correctly.

upside down.

Products and batteries contain materials that can be recovered or recycled, reducing demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com

Technical data

BEMW461ES BEMW471ES BEMW481ES

Voltage

Power inpurt

No-Load

speed

Height

adjustment

Blade length

Weight

-1

min

mm 20 - 70 20 - 70 20 - 70

cm 34 38 42

230 230 230

1400 1600 1800

3500 3500 3500

15.17 15.94 17.17

Hand/arm weighted vibration value:

= 2.5m/s2 , uncertainty (K) = 1.5m/s2.

Sound pressure level at the operator's ear:

LPA: 82dB(A); K= 2.1dB(A)

Sound power level LWA: 95dB(A); K= 1.3dB(A)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

BEMW461ES, BEMW471ES, BEMW481ES lawn mower

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1:2012 + A11:2014,

EN 60335-2-77:2010

2000/14/EC, Lawn Mower, L < 50cm, Annex VI,

DEKRA Certication B.V. Meander 1051 / P.O. Box 5185

6825 MJ ARNHEM / 6802 ED ARNHEM Netherlands.

Level of accoustic power according to 2000/14/EC (Article 12,

measured sound power level LWA: 95dB(A); K= 1.3dB(A).

guaranteed sound power level LWA: 96dB(A).

These products also comply with directive 2014/30/EU,

2011/65/EU. For more information, please contact Black &

Decker at the following address or refer to the back of the

Annex III, L< 50cm):

manual.

Protecting the environment

Separate collection. Products and batteries marked with this symbol must not be disposed of

with normal household waste.

Page 16

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

R. Laverick

Director of Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

31/10/2017

Guarantee

Black & Decker is condent of the quality of its products

and offers consumers a 24 month guarantee from the date of purchase. This guarantee is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

To claim on the guarantee, the claim must be in accordance with Black & Decker Terms and Conditions and you will need to submit proof of purchase to the seller or an authorised repair agent. Terms and conditions of the Black & Decker 2 year guarantee and the location of your nearest authorised repair agent can be obtained on the Internet at www.2helpU.

com, or by contacting your local Black & Decker ofce at the

address indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and receive updates on new products and special offers.

Australia Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100

New Zealand Black & Decker Tel. +64 9 259 1133

United Kingdom & Black & Decker Tel. 01753 511234

Republic Of Ireland 210 Bath Road Fax 01753 512365 www.blackanddecker.co.uk Slough, Berkshire SL1 3YD emeaservice@sbdinc.com

N533563 REV-01 11/2017

20 Fletcher Road, Mooroolbark, Fax 03-9727 5940 Victoria, 3138

5 Te Apunga Place Fax +64 9 259 1122 Mt Wellington Aukland 1060