Black & Decker 9078 User Manual

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust

. Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can

cause you to lose control.

2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current

device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench

or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application.

The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.

Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could

result in a hazardous situation.

5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer.

A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

b) Use power tools only with specifically designated battery packs.

Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like paper

clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6) Service a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a "live"

wire will make exposed metal parts of the tool "live" and shock the operator.

• Use clamps or another practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

•

ANSI Z87.1 eye protection (CAN/CSA Z94.3)

•

ANSI S12.6 (S3.19) hearing protection

•

NIOSH/OSHA/MSHA respiratory protection

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation

which, if not avoided, may result in property damage.

SYMBOLS

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min ........................minutes ......................alternating current

......................direct current

o ........................no load speed

..........................

Class II Construction

........................

earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations per minute

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

9999000077778888 CCCCOOOORRRRDDDDLLLLEEEESSSSSSSS 3333....6666 VVVVOOOOLLLLTTTT 3333 P

PPPOOOOSSSSIIIITTTTIIIIOOOONNNN SSSSCCCCRRRREEEEWWWWDDDDRRRRIIIIVVVVEEEERR

KEY INFORMATION YOU SHOULD KNOW:

TO CHARGE: Charge 12 hours before first use.

TO OPERATE: The black button must be in the forward/reverse position

and depressed to operate tool in either direction. When the button is in the center, it is in a safety position and will not operate.

TO INSTALL A BIT : Insert bit firmly into the cavity in the spindle until it snaps into place. If the bit does not fit into the spindle, rotate the bit and re-insert it.

Pinch Point

Point de pincement

Punto de pellizco

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE

A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

HANK

YOU

FOR

CHOOSING

LACK

&&D

ECKER

OOTTOOWWW

WWW

LACKAND

ECKER

COM

WNER

TTOOREGISTER

YOUR

NEW

PRODUCT

FEATURES (FIGURE A)

1. On/off switch with forward/reverse function

2. Torque adjustment collar

3. Bit holder

4. Handle adjustment button

5. Handle

6. Battery cover

CHARGING THE SCREWDRIVER

Before attempting to charge your screwdriver, thoroughly read all of the safety instructions. To charge your screwdriver, follow the steps below.

1. Plug the output cord of the charger (7) into the socket in the back half of the screwdriver handle (8) as shown in Figure B.

2. Plug the charger into any standard electrical outlet.

CHARGING NOTES

NOTE: The tool was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for 12 hours.

1. Charger will work best at normal room temperature.

2. The charger plug and the tool handle may become warm while charging. This is normal and does not indicate a problem.

3. The tool can be left on charge as long as you desire. A minimum charge time of 12 hours is required to recharge a completely discharged tool.

4. For most fix up jobs a charge of 3 to 4 hours will be adequate.

WARNING: When disconnecting the screwdriver from the charger, be sure to unplug the

charger from the outlet first then disconnect the charger cord from the screwdriver.

Operating Instructions

REMOVING AND INSTALLING BITS

To install a screwdriver bit (9) Fig. C simply insert it into the cavity in the bit holder (3) until it snaps into place. To remove the bit pull it straight out. If bit does not fit, rotate the bit and re-insert it. To insert a bit tip (11) first insert a bit tip holder (10) into the spindle and then insert the bit tip into the holder. NOTE: Screwdriver bit types and quantity may vary.

ADJUSTING THE HANDLE

For optimum versatility, the handle can be be set to different positions as shown in Fig. D. To adjust the handle, press the handle adjustment button (4) and swivel the handle into the desired position. Release the button and the handle will lock in that position. NOTE: To avoid being pinched, grasp the handle below the pinch point shown in Figure D.

OPERATING IN POWER MODE

Forward

• Slide the button (1) shown in Fig. E to the right, exposing the triangle pointing forward.

• Press the button and the tool will run; release the button and the tool will stop.

Reverse

• Slide the button (1) shown in Fig. E to the left, exposing the triangle pointing backward.

• Press the button and the tool will run; release the button and the tool will stop.

OPERATING IN MANUAL MODE

•The tool can be used as a conventional non-powered screwdriver whenever the forward/reverse button is not depressed. With the button (1) in the middle position, the tool will not activate.

SETTING THE TORQUE (FIGURE F)

This tool is fitted with a collar to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials. The collar has a wide range of settings to suit your application.

• Turn the collar (2) to the desired setting. If you do not yet know the appropriate setting, proceed as follows:

• Set the collar to the lowest torque setting.

• Tighten the first screw.

• If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws.

Hints for optimum use

• Always use the correct type of screwdriver bit. Never use a screwdriver bit tip without a bit tip

holder

• If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a

lubricant.

• Use the spindle lock to loosen very tight screws or to firmly tighten screws.

• Always hold the tool and screwdriver bit in a straight line with the screw.

TROUBLESHOOTING

Problem

Possible Cause Possible Solution

• Unit will not start. • Battery not charged. • Check battery charging

requirements.

• Battery will not charge. • Charger not plugged in. • Plug charger into a working

outlet. Refer to “Important Charging Notes” for more details.

• Check current at receptacle by plugging in a lamp or other appliance.

• Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

• Surrounding air temperature • Move charger and tool to a too hot or too cold. surrounding air temperature

of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C).

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

Lubrication

Black & Decker tools are properly lubricated at the factory and are ready for use.

Accessories

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel-cadmium batteries. Help protect our environment and conserve natural resources by returning the spent nickel-

Avertissements de sécurité généraux pour les outils électriques

AVERTISSEMENT! Lire tous les avertissements de sécurité et toutes les directives. Le non-respect des avertissements et des directives pourrait se solder

par un choc électrique, un incendie et/ou une blessure grave.

Conserver tous les avertissements et toutes les directives pour un usage ultérieur.

Le terme «outil électrique» cité dans les avertissements se rapporte à votre outil électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail a) Tenir la zone de travail propre et bien éclairée.

Les endroits sombres sont souvent

des causes d'accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, soit en

présence de liquides inflammables, de gaz ou de poussière.

Les outils

électriques produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les curieux au moment d’utiliser un outil électrique.

Une

distraction pourrait vous en faire perdre la maîtrise.

2) Sécurité en matière d’électricité a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais

modifier la fiche en aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des

tuyaux, des radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc

électrique est plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à d'autres conditions où il

pourrait être mouillé.

La pénétration de l’eau dans un outil électrique augmente le

risque de choc électrique.

d) Ne pas utiliser abusivement le cordon d’alimentation. Ne jamais utiliser le

cordon pour transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de la chaleur, de l’huile, des bords tranchants ou des pièces mobiles.

Les

cordons endommagés ou emmêlés augmentent les risques de choc électrique.

IMPORTANTS RENSEIGNEMENTS :

CHARGEMENT : il faut charger le tournevis pendant 12 heures avant de l’utiliser

pour la première fois.

FONCTIONNEMENT : le bouton noir doit être placé en position de marche avant

ou de marche arrière. Enfoncer le bouton pour faire fonctionner l’outil dans un sens ou dans l’autre et le mettre en position centrale pour verrouiller l’outil en position d’arrêt.

INSTALLATION DE LA MÈCHE : pour installer une mèche, il suffit de l’enfoncer

fermement dans la cavité de la broche jusqu’à ce qu’elle soit bien enclenchée. Si la mèche ne s’insère pas correctement dans la broche, la faire pivoter et l’insérer à nouveau.

TTTTOOOOUUUURRRRNNNNEEEEVVVVIIIISSSS SSSSAAAANNNNSSSS FFFFIIIILLLL ÀÀÀÀ 3333 PPPPOOOOSSSSIIIITTTTIIIIOOOONNNNSSSS

DDDDEEEE 3333,,,,6666 VVVVOOOOLLLLTTTTSSSS,,,, MMMMOOOODDDDÈÈ

ÈÈLLLLEEEE 9999000077778888

cadmium battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call 1-800-8-BATTERY.g center for information on where to drop off the spent battery, or call 1-800-8-BATTERY.

BATTERY PACK REMOVAL IMPORTANT: This tool is designed for easy disassembly for the purpose of battery pack

removal. It is not designed to be re-assembled by the consumer. Before attempting to disassemble this tool, turn it on and run it in either direction until it stops to ensure a complete discharge of the battery pack. To disassemble the tool, remove the screws in the side of the tool body. Take the two body halves apart and you will find the battery pack. Lift the battery pack out and pull off the terminal clips.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "ToolsElectric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUE CE SOIT, COMPOSER LE

1-800-544-6986

AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART

DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR

TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS

IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.

ERCI

ERCIDD

’

AAVOIR

VOIR

CHOISI

LACK

&&D

ECKER

ISITEZ

WWW

LACKAND

ECKER

COM

RODUCT

EGISTRA

TION

POUR

ENREGISTRER

VOTRE

NOUVEAU

PRODUIT

MODE D’EMPLOI

CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.

Imported by: Black & Decker (U.S.) Inc., 701 E. Joppa Rd. Towson, MD 21286 U.S.A.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

+ 4 hidden pages