Black & Decker 90558474, V-2 Million, SL302B User Manual

FICHE TECHNIQUE

Ampoule du projecteur : 12 volts, série H3, ampoule à filament double de 55 W et 35 W Pile : au plomb scellée, sans entretien, de 12 volts, 3 ampères-heures Chargeur inclus à CA : homologué UL, classe 2, courant continu de 12 volts (300 mA) Fusible de la fiche de courant continu : 2 A, 250 V

V-2 MILLION POWER SERIES

™

SPOTLIGHT

INSTRUCTION MANUAL

Catalog Number SL302B

Thank you for choosing Black & Decker!

Go to www.BlackandDecker.com/NewOwner

to register your new product.

PLEASE READ BEFORE RETURNING THIS

PRODUCT FOR ANY REASON:

If you have a question or experience a problem with your Black & Decker purchase, go to

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

If you can’t find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.

Please have the catalog number available when you call.

for instant answers 24 hours a day.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

Imported by / Importé par

Black & Decker Canada Inc.

100 Central Ave.

Brockville (Ontario) K6V 5W6

Voir la rubrique “Outils

électriques”

des Pages Jaunes

pour le service et les ventes.

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 24

• DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or explosive atmospheres.

Motors in these tools normally spark, and the sparks might ignite fumes.

• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use

outdoors and so marked.

• EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure

to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:

• Do not plug in a power supply without the bulb lens and cover in place.

• Do not put spotlight in water or other liquid. Do not place or store spotlight where it can fall or be pulled into a tub or sink.

• Keep the lens in place.

• Do not operate this unit without the lens.

WARNING: FIRE HAZARD: Never contact combustible material to the lens. WARNING: BURN HAZARD: Hot lens. May cause property damage or fire. Do not touch or obstruct lens.

• All halogen lights give off heat:

– Do not touch lens while operating. – Keep combustibles away from spotlight lens. Extreme heat can cause fires. – Never place the light face-down on any surface when lit and following recent use. – Do not touch the lens or enclosure as it becomes hot during operation and remains hot for several

minutes after the spotlight is switched off. – Allow the spotlight to fully cool down before storage or charging. – Do not leave the spotlight unattended. Keep children and animals away from the work area.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

• Use only on a flat, stable surface. When a cart is used, use caution when moving the spotlight/cart combination to avoid injury from tip-over. Never place the light face-down on any surface.

• Never look directly into the light or shine the light into another person’s eyes.

• Keep sharp objects away from lens — it is glass and can break.

• The lens of the light blocks harmful UV radiation. Do not use if the lens becomes cracked or broken.

• Do not immerse spotlight in water.

• Do not drop or throw spotlight. It contains glass and a sealed lead acid battery.

• Use in a dry location only.

• Do not open body casing. There are no user-serviceable parts inside.

CHARGING SAFETY WARNINGS

AND GUIDELINES

Before using battery charger, read all instructions and cautionary markings on battery charger and unit.

CAUTION: To reduce the risk of injury, charge only Black & Decker Batteries. Other types of batteries may

burst causing personal injury and damage.

• NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.

• Plug in the charging adapter at the spotlight first, then plug into the charging source.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7.6m) (7.6-15.2m) (15.2-30.4m) (30.4-45.7m)

240V 0-50 51-100 101-200 201-300

(0-15.2m) (15.2-30.4m) (30.4-60.9m) (60.9-91.4m)

Ampere Rating

More Not more American Wire Gauge Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended

SAFETY GUIDELINES / DEFINITIONS

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided,

may result in property damage. RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be

followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Black & Decker strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool or equipment.

IMPORTANT SAFETY INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL APPLIANCES

READ ALL INSTRUCTIONS

WARNING: Read all instructions before operating product. Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

• AVOID DANGEROUS ENVIRONMENTS Don’t use appliances in damp or wet locations. Don’t use appliances in the

rain.

• KEEP CHILDREN AWAY. All visitors should be kept at a distance from work area.

• STORE IDLE APPLIANCES INDOORS. When not in use, appliances should be stored indoors in dry, and high or

locked-up place – out of reach of children.

• DON’T FORCE APPLIANCE. It will do the job better and with less likelihood of a risk of injury at the rate for

which it was designed.

• USE RIGHT APPLIANCE. Do not use the appliance for any job except that for which it is intended.

• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves

and substantial, non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with side

shields, complying with applicable safety standards and, when needed, a face shield. Also use face or dust mask if operation is dusty. This applies to all persons in the work area. Also use a hard hat, hearing protection, gloves, safety shoes and dust collection systems when specified or required. Safety glasses or the like are available at extra cost at your local dealer or Black & Decker Service Center.

• DON’T ABUSE CORD. Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from

heat, oil, and sharp edges.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• DISCONNECT APPLIANCE. The AC Charger and DC Charging Adapter should be maintained in a readily operable

condition. To avoid damage to the unit or Adapter, disconnect the unit from any power supply when not in use, before cleaning, during lightning storms, and changing accessories or when it will be unused for long periods of time. To disconnect the unit from the power supply, the AC Charger must be completely disconnected from any AC extension cord and the DC Charging Adapter.

• AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in appliance with finger on switch. Be sure switch is

off when plugging in.

• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuits or outlets to be

used. Receptacles are available having built in GFCI protection and may be used for this measure of safety.

• USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or

attachment not recommended for use with this appliance could be hazardous. Note: Refer to the accessory section of this manual for further details.

• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired.

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it ON and OFF.

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 2

CHARGING/RECHARGING THE SPOTLIGHT

This unit is shipped in a partially charged state. Charge unit BEFORE first use using the 120 Volt AC Charger for 18-24 hours or until the green Battery Status LED Indicator lights. Charge after each use until green Charge Status LED Indicator lights.

Charging/Recharging Using the 120 Volt AC Charger and a Standard Household Extension Cord (not included)

Plug a standard North American 120 volt AC extension cord (not included) into the 120 Volt AC Charger on the back of the unit.

Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed).

Charge for 18-24 hours or until the green Battery Status LED Indicator lights. Notes: To extend battery life, disconnect the charger after 48 hours.

All batteries lose charge with time, especially when they are warm. Recharge the unit every two months for 18-24 hours when not in frequent use. If the unit is not going to be used for extended periods, disconnect the charger and store in a cool, dry place.

Charging/Recharging Using the 12 Volt DC Charging Adapter

Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging Port (shown in the illustration below).

Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source. Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed). Charge until the green Charge Status LED Indicator lights.

Notes:When using a vehicle’s 12 volt DC accessory outlet as a charging source, be aware that some vehicles

require you to turn on the ignition to power the accessory outlet. To avoid deeply discharging your vehicle battery we recommend to have the vehicle running while recharging the light with the DC recharge adapter.

WARNING: NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.

OPERATING INSTRUCTIONS

The Trigger Switch is located on the front of the pistol-grip handle of the spotlight (refer to the “Controls and Functions” illustration).

• Turn on the Spotlight by squeezing the ON/OFF Trigger.

• Turn off the Spotlight by releasing the ON/OFF Trigger.

To lock the Trigger in the ON position for continuous operation, squeeze the ON/OFF Trigger and slide theTrigger Lock Button located on the side on the handle DOWN (refer to the “Controls and Functions” illustration). The Spotlight will stay ON until you slide the Trigger Lock Button back UP.

Dimmer Switch

The Dimmer Switch is located on the top of the Spotlight (refer to the “Controls and Functions” illustration). Sliding the switch forward (toward the Spotlight bulb) sets the Spotlight on High Beam; sliding the switch backward sets the Spotlight on Low Beam.

Using the Carry Handle as a Stand For Hands-Free Operation

Invert the unit to use the Carry Handle as a stand, and set it upon a flat, stable surface for hands-free operation.

Using the Built-In Carry Lanyard

The Carry Lanyard may be used to store or carry the Spotlight; and also allows you to position the Spotlight for convenient, hands-free operation.

12 VOLT DC CHARGING PORT (UNDERSIDE OF UNIT)

12 VOLT DC CHARGING ADAPTER

BUILT-IN 120V AC CHARGER

CHARGE STATUS LED INDICATORS

• Note: To ensure maximum battery life do not overcharge. Only charge until the green LED charge status indicator

lights.

• Do not expose charger to rain or snow. Use in a dry location only.

• Do not crush, cut, pull or expose charger cords to extreme heat.

• Position charger cords so they do not become entangled or become a safety hazard. Keep charger cords away from sharp edges.

• To reduce risk of damage to plug and cord, pull by plug rather than cord when disconnecting unit from the charger.

• Use of improper extension cord could result in a risk of fire, electric shock or electrocution.

• Use only the supplied chargers when charging this spotlight. The use of any other charger could damage the spotlight or create a hazardous condition.

• Use only one charger when charging.

• Do not attempt to charge the unit if the charger plug is damaged— return the unit to manufacturer for repair.

• Do not attempt to open the charger. There are no customer serviceable parts inside. Return to manufacturer for repair.

• All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF position before connection to a power source or load.

• After charging/recharging, disconnect charger or extension cord and wait 5 minutes before use.

• This unit contains a non-spillable battery. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/or moisture.

• FIRST AID – SKIN: If battery acid comes in contact with skin, rinse immediately with water, then wash

thoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention. EYES: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate medical attention.

IMPORTANT:

• This unit is delivered in a partially charged state. Fully charge unit for 18-24 hours using the AC charging method before using for the first time. Green indicator will light when fully charged.

• Read And Understand This Instruction Manual Before Using This Unit.

SAVE THESE INSTRUCTIONS

INTRODUCTION

Thank you for choosing the

Black & Decker®V-2 Million Power Series™Spotlight.

Please read this guide

carefully before use to ensure optimum performance and to avoid damage to the unit.

FEATURES

• Powerful, focused quartz halogen beam with Dimmer Switch for high and low settings

• Safety cap protects 120 volt AC charger

• Comfortable pistol grip, handle and carry lanyard

• Charge Status LED Indicator

• UL listed, built-in 120 volt AC charger that works with a standard household extension cord (not included)

• 12 volt DC charging adapter included

• Rechargeable, non-spillable, sealed lead acid battery

Controls and Functions

ON/OFF

TRIGGER

DIMMER SWITCH

120 VOLT AC CHARGER (BACK OF UNIT)

CHARGE STATUS LED INDICATOR

TRIGGER LOCK

CARRY LANYARD

PISTOL GRIP HANDLE

QUARTZ HALOGEN BULB

12 VOLT DC CHARGING PORT

(UNDERSIDE OF UNIT)

CARRY HANDLE

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 4

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this spotlight could be hazardous and will

void manufacturer’s warranty.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools–Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: Do not open body casing. There are

no user-serviceable parts inside.

FULL ONE YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for one year against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT:

If your warning labels become illegible or are missing, call 1-800-544-

6986 for a free replacement.

SPECIFICATIONS

Spotlight Bulb: 12 volt, H3 series, dual-filament 55W/35W bulb Battery: Maintenance-free, sealed lead acid, 12 volt, 3 amp hour Embedded AC Charger: UL Listed Class 2, 12 volt DC (300 mA) DC Plug Fuse: 2 A/250 V

Problem Solution

Spotlight will not operate 1. If you suspect the bulb is blown, check the filament. If the filament is

coiled and unbroken, the bulb is not blown. If bulb is blown, call 1-800-544-6986 to locate the nearest authorized service center. The bulb is NOT user-replaceable.

2. The light may be charging/recharging using the 12 volt DC charging adapter. The unit will not operate while charging/recharging via the DC charger. Unplug from the 12 volt DC power source.

3. The battery may be completely discharged. Charge the unit following the directions in this Instruction Manual.

4. If the Spotlight does not operate after recharging as directed, contact Technical Support toll-free at 1-800-544-6986.

Cannot depress trigger Slide Trigger Lock Button on side of handle UP to unlock the Trigger.

CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:

• Only use the Carry Lanyard for carrying or hanging the Spotlight. The Carry Lanyard is not intended to support additional weight. Do not attach or hang anything additional to the light or risk of breakage may occur.

• When light is hung by the Carry Lanyard, do not shake the light or object that it is hanging from. Do not hang the light from electrical wires or anything that it is not secure.

CARE AND MAINTENANCE

All batteries lose charge with time, especially when they are warm. Recharge the unit every two months when not in frequent use, preferably using the 120 volt AC method.

Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with a mild solution of water and detergent.

Battery Replacement/Disposal

BATTERY REPLACEMENT The battery should last the service life of the unit. Contact Technical Support toll-free at 1-800-544-6986 for any information you may need.

BATTERY DISPOSAL Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is required — contact your local authority for information. Failure to comply with local, state and federal regulations can result in fines or imprisonment. For more information on recycling this battery, call toll-free 1-800-544-6986.

WARNINGS:

• Do not dispose of the battery in fire as this may result in an explosion.

• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).

• Do not expose battery to fire or intense heat as it may explode.

• For more information on recycling this battery, call toll-free 1-800-544-6986.

12 Volt DC Charging Adapter Plug Fuse Replacement

The fuse in the plug end of the 12 Volt DC Charging Adapter protects the adapter’s charging circuit. If the 120 Volt AC Charger operates, but the DC charging adapter does not, then this fuse may be opened (blown).

To replace the fuse:

1. Unscrew the end cap of the DC plug (counterclockwise).

2. Remove spring center contact and fuse.

3. Check fuse with a continuity checker.

4. If blown, locate a replacement 2 amp/250 volt fuse.

5. Replace the fuse, spring, contact and end cap.

6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.

7. Test for proper operation of the 12 Volt DC Charging Adapter.

TROUBLESHOOTING

Problem Solution

Spotlight will not charge (green Charge Status LED Indicator does not light)

1. Check connection to the 120 Volt AC Charger (or DC Charging Port).

2. Check connection to AC (or DC) power source.

3. Confirm there is a functioning AC (or DC) current.

4. Make sure the Trigger is not pressed (pressing the Trigger when one of the charging adapters is plugged in interrupts the charging process).

5. Make sure the Trigger Lock is not engaged. It is possible to have left the Trigger Lock ON when the battery discharged. The Spotlight will not charge until the Trigger is unlocked.

6. If the Spotlight will not charge after checking all of the above, contact Technical Support toll-free at 1-800-544-6986.

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

Imported by

Black & Decker (U.S.)

Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

90558474 SL302B.qxp:SL302B ManualENSPFR 073008 11/25/09 1:20 PM Page 6

+ 8 hidden pages