Black & Decker 90547733, LPS7000 User Manual

Catalog Number LPS7000

SAVE THIS MANUAL FOR FUTURE REFERENCE.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZADE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Thank you for choosing Black & Decker!

Go to www.BlackandDecker.com/NewOwner

to register your new product.

PPLLEEAASSEE RREEAADD BBEEFFOORREE RREETTUURRNNIINNGG TTHHIISS

PPRROODDUUCCTT FFOORR AANNYY RREEAASSOONN::

If you have a question or experience a problem with your Black & Decker purchase, go to

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

If you can’t find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.

Please have the catalog number available when you call.

for instant answers 24 hours a day.

CORDLESS LITHIUM-ION COMPACT SAW

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 1

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools. Unmodified

plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of

electric shock.

3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-related hazards.

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 2

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could

result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with another battery pack.

b) Use power tools only with specifically designated battery packs. Use of any

other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid contact.

If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tool by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire

will make exposed metal parts of the tool “live” and shock the operator.

• Use clamps or another practical way to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

• When not in use, place tool on its side on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large battery packs will stand upright but may

be easily knocked over.

• Keep hands away from cutting area. Never reach underneath the material for any

reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers or thumb into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the saw by gripping the shoe.

• Keep blades sharp. Dull blades may cause the saw to swerve or stall under pressure.

• Use extra caution when cutting overhead and pay particular attention to overhead

wires which may be hidden from view. Anticipate the path of falling branches and debris ahead of time.

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 3

• When cutting pipe or conduit ensure that they are free from water, electrical wiring, etc.

• Do not touch the workpiece or the blade immediately after operating the tool. They

can become very hot.

• Do not use in rain or wet conditions.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety

glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSAZ94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Do not operate this tool for long periods of time. Vibration caused

by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 4

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating

current

......................direct current

o ........................no load speed

..........................

Class II Construction

........................earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations per minute

Safety Warnings and Instructions: Batteries

• Do not disassemble or open, drop (mechanical abuse), crush, bend or deform, puncture,

or shred.

• Do not modify or remanufacture, attempt to insert foreign objects into the battery,

immerse or expose to water or other liquids, or expose to fire, excessive heat including soldering irons, or put in microwave oven.

• Only use the battery/tool with a charging system specified by the manufacturer/supplier.

• Do not short-circuit a battery or allow metallic or conductive objects to contact both

battery terminals simultaneously.

• Dispose of used batteries promptly according to the manufacturer/supplier’s instructions.

• Improper battery/tool use may result in a fire, explosion, or other hazard.

• Battery/tool usage by children should be supervised.

Safety Warnings and Instructions: Charging

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary warnings on battery

charger and product using battery. CAUTION: To reduce the risk of injury, use this charger only with this product. Batteries in other products may burst causing personal injury or damage.

3. Do not expose charger to rain or snow.

4. Use of an attachment not recommended or sold by Black & Decker may result in a

risk of fire, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

7. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.

FUNCTIONAL

DESCRIPTION - Figure A

1. On/off switch

2. Lock-off button

3. Charging socket

4. Shoe

5. Blade clamp release lever

6. LED light

7. Charger

8. Charger plug

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 5

M T

a. An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size.

CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS

NAMEPLATE RATING AMPS – 0 – 10.0

Total Extension Cord Length (ft)

0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

Wire Gauge 18 16 16 14

8. Use only the supplied charger when charging your tool. The use of any other charger

could damage the tool or create a hazardous condition.

9. Use only one charger when charging.

10. Do not attempt to open the charger. There are no customer serviceable parts inside.

Return to any authorized Black & Decker service center.

11. DO NOT incinerate the tool or batteries even if they are severely damaged or

completely worn out. The batteries can explode in a fire. Toxic fumes and materials are created when lithium ion battery packs are burned.

12. Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.

13. If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for three minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or

flame.

CHARGING PROCEDURE - FIGURE B & B1 IMPORTANT: The batteries in your tool are not fully

charged at the factory. Before attempting to charge them, thoroughly read all of the safety instructions.

(1) The charging socket (3) is keyed to lock out other chargers. Align the tab in the charger plug (8) with the key in the charging socket (see figure B). (2) Plug the charger output plug (8) into the charging socket (3) of the tool as shown in figure B1. (3) Plug the charger (7) into any standard 120 Volt 60 Hz electrical outlet. (4) Let the tool charge initially for at least 10 hours. After the initial charge, your tool should be fully charged in 10 hours from a fully discharged condition.

Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished. For longest battery life, do not discharge batteries fully. It is recommended that the

batteries be recharged after each use.

WARNING: Do not use tool while it is connected to

the charger.

WARNING: Fire Hazard. When disconnecting the charger from the tool, be sure to unplug the charger from the outlet first, then disconnect the charger cord from the tool.

Important Charging Notes

1. Your tool was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 10 hours.

2. CAUTION: To reduce the risk of damage to the batteries, NEVER charge them in an air temperature below 40°F (4.5°C) or above 105°F (40.5°C). Also, NEVER charge them if the battery temperature is below 40°F (4.5°C) or above 105°F (40.5°C). Longest life and best performance occurs when batteries are charged with an air

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 6

temperature of approximately 75°F (24°C). NOTE: The tool will not charge if the tool temperature is below approximately 32°F (0°C) or above 113°F (45°C).

3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.

4. If the batteries do not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and tool to a surrounding air temperature of 40°F (4.5°C) to 105°F (+40.5°C). (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the tool and charger to your local Black & Decker service center. See Tools Electric in yellow pages.

5. The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. Battery life may be greatly diminished if batteries are discharged deeply. DO NOT CONTINUE using product with its batteries in a depleted condition. Recharge discharged batteries promptly.

6. To maximize battery life: a. Do not fully discharge batteries. b. Fully recharge batteries after each use. c. Store tool in a location where the surrounding air temperature is approximately 40°F

- 75°F (4.5°C - 24°C). d. Disconnect charger from tool after charge is complete. WARNING: Fire Hazard.

When disconnecting the charger from the tool, be sure to unplug the charger from the outlet first, then disconnect the charger cord from the tool.

OPERATING INSTRUCTIONS

WARNING: Always wear proper eye and respiratory protection while operating this

tool.

• Use clamps or another practical way to

secure and support the workpiece to a stable platform. Holding the work by hand

or against your body leaves it unstable and may lead to loss of control.

• Place blade and shoe lightly against work to

be cut.

• Switch on saw motor and allow it to obtain

maximum speed before applying pressure.

TRIGGER SWITCH (FIGURE C)

The tool is equipped with a switch lock-off feature to prevent unintentional operation.

• To switch the tool on, press the lock off

button (2) from either side, then squeeze the on/off switch (1).

• After the tool is running, release the switch

lock-off button. The tool will continue to run as long as the trigger is depressed.

• To switch the tool off, release the on/off

switch. There is no provision for locking the tool on.

• This tool is designed with two gripping

surfaces for optimal control. Hold saw

firmly with one hand (figure C) or both hands (figure D) while cutting.

The saw can be used in either of the modes shown in figure E. Whenever possible, the saw shoe (4) must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage.

• A light (6) is built-in to the saw above the

blade holder (5). The light will automatically come on each time the on/off switch is depressed.

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 7

M T

T M

JIG SAW / RECIPROCATING SAW MODES (FIGURES F, F1)

The LPS7000 can be used in two different ways: JIG SAW MODE - Blade teeth face forward as shown in figure F. RECIPROCATING MODE - Blade teeth face downward as shown in figure F1. The LPS7000 accepts T-shank blades only. Thin kerf 10tpi or higher blade recommended

BLADE CLAMP RELEASE LEVER (FIGURE G)

CAUTION: Burn hazard. Recently used

blades may be hot.

To install blade into saw:

• Push down on the blade clamp release lever (5)

to its full open position as shown.

• Insert blade shank (9) from the front.

• Release the blade clamp release lever (5).

To remove blade from saw:

• Push down on the blade clamp release

lever (5) to its full open position.

• Remove blade.

• Release the blade clamp release lever (5).

WOOD CUTTING NOTE: Use “T” shank 10tpi or higher, thin kerf blades.

• Before cutting any type of wood, use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

• Place shoe firmly against work to be cut.

• Switch on saw motor before applying pressure.

• Whenever possible, the shoe must be held firmly against the material being cut. This will

prevent the saw from jumping or vibrating and minimize blade breakage.

TREE TRIMMING

• Hold shoe firmly against tree branch. If possible, cut close to the trunk to minimize

movement of the branch.

METAL CUTTING (FIGURE H)

NOTE: Use “T” shank 18-24 tpi metal cutting blade.

• In thin gauge sheet metals it is best to

clamp thin plywood to underside of sheet. This will ensure a clean cut without excess vibration or tearing of metal.

• Avoid forcing cutting blade as this reduces

blade life and causes costly blade breakage.

• When cutting metal piping, do not cut

directly through the pipe as you would saw a wooden dowel. Instead, cut around the circumference of the pipe to avoid pinching the blade. Only one section of the blade

should be in contact with the pipe. NOTE: You should spread a thin film of oil or other coolant along the line ahead of the saw cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

PROJECT TIPS

• Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor

while cutting.

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 8

M T

T M

• When cutting, always ensure that the shoe is resting against the workpiece. This will

improve operator control and minimize vibration.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT:To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

BATTERY DISPOSAL

Before attempting to disassemble this tool, turn it on and run it until it stops to ensure a complete discharge of the batteries. Using a screwdriver, remove the screws in the product housing and lift the housing half from the tool. Disconnect the terminal clips from the batteries and lift the batteries out.

TROUBLESHOOTING

oblem Possible Cause Possible Solution

• Unit will not start. • Battery not charged. • Check battery charging

requirements.

• Battery will not charge. • Charger not plugged in. • Plug charger into a

working outlet. Refer to “Important Charging Notes” for more details.

• Check current at receptacle by plugging in a lamp or other appliance.

• Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

• Surrounding air temperature • Move charger and tool

too hot or too cold. to a surrounding

air temperature of above 40 degrees F (4.5°C) or below 105 degrees F (+40.5°C).

• Charger jack not fully plugged • Check to be sure

into tool charging socket. charger plug is fully

inserted into unit tool charging socket.

• Blade comes out of unit. • Blade not fully inserted in • Check to be sure blade

blade clamp. is fully inserted into blade

clamp

• On/Off Trigger will not activate. • Lock-off not depressed. • Check to be sure lock-off

is depressed.

• Poor cutting performance. • Dull blade • Replace blade. For assistance with your product, visit our website www.blackanddecker.com for the

location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986. ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 9

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lithium-ion battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent lithium-ion batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative. RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent lithium-ion batteries. Help protect our environment and conserve natural resources by returning the tool to an authorized Black & Decker service center for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or cal

1-800-8-BATTERY.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com. This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 10

MODE D’EMPLOI

N° de catalogue LPS7000

Merci d’avoir choisi Black & Decker!

Consulter le site Web

www.BlackandDecker.com/NewOwner

pour enregistrer votre nouveau produit.

LLIIRREE AAVVAANNTT DDEE RREETTOOUURRNNEERR CCEE PPRROODDUUIITT

PPOOUURR QQUUEELLQQUUEE RRAAIISSOONN QQUUEE CCEE SSOOIITT ::

Si des questions ou des problèmes surgissent après l’achat d’un produit Black & Decker,

consulter le site Web

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

Si la réponse est introuvable ou en l’absence d’accès à Internet, composer le

1-800-544-6986 de 8 h à 17 h HNE, du lundi au vendredi, pour parler avec un agent.

Prière d’avoir le numéro de catalogue sous la main lors de l’appel.

pour obtenir des réponses instantanément 24 heures par jour.

CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.

SCIE SANS FIL COMPACTE À BLOC-PILES

AU LITHIUM-ION

90547733 LPS7000 Saw 6/11/09 7:21 AM Page 11

+ 25 hidden pages