Black & Decker 90512730 User Manual

WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS

WARNING: When using gardening appliances, basic safety precautions should always

be followed to reduce risk of fire, electric shock, and personal injury, including the following.

WARNING: Some dust created by this product contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING.

• Before any use, be sure everyone using this garden appliance reads and understands all safety instructions and other information contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.F

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL

APPLIANCES

• ALWAYS WEAR EYE PROTECTION – Wear safety spectacles or goggles at all times

when this tool is plugged in.

• GUARD – Do not use this tool without guard attached.

• DRESS PROPERLY – Do not wear loose clothing or jewelry. They can be caught in

moving parts. Rubber gloves and substantial rubber soled footwear are recommended when working outdoors. Don’t operate the tool when barefoot or wearing open sandals. Wear long pants to protect your legs. Wear protective hair covering to contain long hair.

• NYLON LINE – Keep face, hands and feet clear of rotating nylon line at all times.

• THE ROTATING LINE PERFORMS A CUTTING FUNCTION – Use care when trimming

around screens and desirable plantings.

• KEEP ALL BY-STANDERS AWAY – at a safe distance from work area, especially

children.

• IMPORTANT WARNING – When being used as an Edger, stones, pieces of metal and

other objects can be thrown out at high speed by the line. The tool and guard are designed to reduce the danger. However, the following special precautions should be taken:

• MAKE SURE that other persons and pets are at least 100 feet away.

• TO REDUCE THE RISK of rebound (ricochet) injury, work going away from any nearby solid object such as wall, steps, large stone, tree, etc. Use great care when working close to solid objects and where necessary, do edging or trimming by hand.

• AVOID ACCIDENTALLY STARTING – Don’t carry plugged-in tool with finger on trigger.

• DO NOT FORCE THE TOOL – at a rate faster than the rate at which it is able to cut

effectively.

• USE THE RIGHT TOOL – Do not use this tool for any job except that for which it is

intended.

• DON’T OVERREACH – Keep proper footing and balance at all times.

• DON’T ABUSE CORD – Don’t yank cord from power supply. Keep cord from heat, oil, and

sharp edges.

• DAMAGE TO UNIT – If you strike or become entangled with a foreign object, stop tool

5°-10°

INSTRUCTION MANUAL

Catalog Number: GH600

GGGGHHHH666600000000 TTTTrrrriiiimmmmmmmmeeeerrrr////EEEEddddggggeeeerr

KEY INFORMATION YOU SHOULD KNOW:

• The guard must be installed before trimming or edging - if not, the motor will overheat.

• When replacing the line, use only .065”

diameter ROUND line - otherwise the unit will not function properly.

• Do not bump the feed head against the ground

- it will disrupt the feed mechanism.

• Angle tool slightly (5

° to 10°) when trimming.

Date Code:

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., AND

DATE CODE . IN MOST CASES, ABLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM

OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS

VITALTO BLACK & DECKER.

HANK

YOU

FOR

CHOOSING

LACK

&&D

ECKER

OOTTOOWWW

WWW

LACKAND

ECKER

COM

WNER

TTOOREGISTER

YOUR

NEW

PRODUCT

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZADE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates potentially hazardous situation

which, if not avoided, may result in property damage.

immediately, unplug, check for damage and have any damage repaired before further operation is attempted. Do not operate with a broken hub or spool.

• DAMAGE TO CORD – Keep power cord away from rotating line. If you damage the cord, unplug it from the power supply before moving the tool or examining the damage. A damaged cord must be replaced before further use.

• DISCONNECT TOOL – when not in use, when replacing line, or prior to cleaning.

• AVOID DANGEROUS ENVIRONMENTAL CONDITIONS – Do not use electric tools in damp or wet locations. Follow all instructions in this Instruction Manual for proper operation of your tool. Don’t use the tool in the rain.

• DO NOT OPERATE portable electric tools in gaseous or explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.

• STORE IDLE TOOLS INDOORS – When not in use, tools should be stored indoors in a dry, locked-up place out of reach of children.

• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuits or outlets to be used for the gardening appliance. Receptacles are available having built in GFCI protection and may be used for this measure of protection.

• SECURE EXTENSION CORD using the cord retainer shown in Figure 5.

• STAY ALERT – Watch what you are doing. Use common sense. Do not operate tool when you are tired.

• MAINTAIN APPLIANCES WITH CARE – Follow instructions in maintenance section. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free from oil and grease.

• CHECK DAMAGED PARTS – Before further use of the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this manual.

• WARNING: When servicing double insulated tools, USE ONLY IDENTICAL REPLACEMENT PARTS. Replace or repair damaged cords.

• WARNING: To prevent electrical shock hazard, use only with an extension cord suitable for outdoor use. Always connect extension cords to a fused line or one protected by a circuit breaker.

SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way.

SAFETY WARNINGS AND INSTRUCTIONS: EXTENSION CORDS

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. If the extension will be used outside, the cord must be suitable for outdoor work. The letters “WA” on the cord jacket indicate that the cord is suitable for outdoor use.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

Ampere Rating

More Not more American Wire Gage Than Than 0-6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended

IMPORTANTS RENSEIGNEMENTS :

• Installer le dispositif de protection avant d’utiliser l’outil afin d’éviter de

surchauffer le moteur.

• N’utiliser que du fil ROND de 1,65 mm (0,065 po) de diamètre. Sinon, l’outil

ne fonctionnera pas correctement.

• Ne pas cogner la tête du mécanisme d’alimentation contre le sol afin de ne

pas l’abîmer.

• Incliner légèrement l’outil (de 5 à 10 degrés) durant la coupe d’une bordure.

• Toujours utiliser le dispositif de retenue et le dispositif de verrouillage de la

rallonge.

CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.

LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS

Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les symboles ci-dessous servent à vous aider à reconnaître cette information.

DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera

la mort ou des graves blessures.

AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle n’est pas

évitée, pourrait causer la mort ou de graves blessures.

MISE EN GARDE : Indique une situation potentiellement dangereuse qui, si elle n’est pas

ASSEMBLY / ADJUSTMENT SET-UP

• WARNING: The guard must always be on the tool to protect the user. NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE.

UNPLUG THE TOOL BEFORE ATTEMPTING TO ATTACH THE GUARD.

1. Position the open center of the guard over the line feed head (Figure 1).

2. Hinge the guard on the hook located on the lower motor housing. Ensure the line is free, and not tucked under the guard. Once hooked, lightly pull on the back edge of the guard and push the guard down until the 3 latches snap into place on the motor housing. (Figure 2)

3. The guard is not

intended to be removed once installed.

4. Once the guard is installed, remove the covering from the line cut-off blade, located on the edge of the guard.

5. The auxiliary handle can be adjusted along the tube. Simply loosen the knob and position the handle as desired. Retighten knob to secure the auxiliary handle. (Figure 3)

6. The GH600 allows you to adjust the length of the tube. Loosen the knob located on the auxiliary handle. Next, adjust the height of the main handle by pushing the button and moving the handle up or down as shown in figure 4. Finally, adjust the location of the auxiliary handle as required (figure 3), securing it in place by retightening the knob.

7. An extension cord retainer (figure 5) is built into the switch handle that prevents the cord from coming unplugged. To use this feature, simply double the extension cord about 8 inches from the end, and insert it into the slot in the bottom of the handle area. Hook the loop formed by doubling the cord over the tab. Gently tug on the cord to insure that it is firmly retained in the trimmer’s handle. Plug the receptacle end of the extension cord into the plug blades in the trimmer.

OPERATING INSTRUCTIONS

• CAUTION: ALWAYS WEAR EYE PROTECTION

• CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence.

• Angle unit as shown in Figure 6.

• With the unit on, slowly swing the trimmer side to side as shown in Figure 7.

• To convert for maintenance edging, unplug the unit from the power source. Gently pull the wire edge guide down into place as shown in Figure 8 and 9. Push the black “For Edging” button and rotate the lower motor housing 180°. The tool will lock in the edger position.

• To operate as a maintenance edger, position the trimmer above the surface as shown in Figure 10.

• Return to the trimming position by unplugging the unit from the power source, pushing the black “For Edging” button and rotating the lower motor housing back 180°. The tool will lock in the trimmer position.

When using the tool put up the wire edge guide to the original position, out of the way.

CUTTING LINE

LINE FEEDING

Your trimmer uses .065” (1.65 mm) diameter, ROUND nylon line to cut grass and weeds quickly and easily. During use, the tip of the nylon line will become frayed and worn and the special self feeding line hub will automatically feed and trim a fresh length of line. Cutting line will wear faster and require more feeding if the cutting or edging is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. The advanced automatic line feeding mechanism senses when more cutting line is needed and feeds and trims the correct length of line whenever its required. DO NOT BUMP unit on ground in attempt to feed line or for any other purposes.

CLEARING JAMS AND TANGLED LINES

From time to time, especially when cutting thick or stalky weeds, the line feeding hub may become clogged with sap or other material and the line will become jammed as a result. To clear the jam, follow the steps listed below.

1. Unplug the trimmer.

2. Press the release tabs on the line hub cap, as shown in Figure 11 and remove the cap by

pulling it straight off.

3. Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from

the spool area. (If you plan to replace the spool or rewind it, this is the place to do so, otherwise, move on.)

4. Unwrap about one foot (30 cm) of line to ensure that it’s undamaged. If it is OK rewind it

and insert the line end through the eyelet in the spool hub as shown in Figure 12. Pull 4” (10 cm) of the line through the hole and maintain tension while placing the spool down into the hub with the arrow up, as shown in Figure 13.

5. Press the spool down GENTLY and rotate it until you feel it drop into place. (When in

place, the spool will turn a few degrees left and right freely). Take care to keep the line from becoming trapped under the spool.

6. Snap the hub cap and spring back on, and power the tool on. In a few seconds or less

you’ll hear the nylon line being cut automatically to the proper length.

SPOOL OR LINE REPLACEMENT (Use .065” diameter ROUND line only)

1. Perform steps 1 and 2 above.

2. Remove the spool from the tool and remove and discard all line on the spool.

3. Choose either OPTION 1 or OPTION 2 below for spool or line replacement.

4. Insert the line end through the eyelet in the spool hub, as shown in Figure 12. Pull the line

through the hole to maintain tension while placing the spool down into the hub, as shown in Figure 13.

5. Press the spool down GENTLY and rotate it until you feel it drop into place. (When in

place, the spool will turn a few degrees left and right freely). Take care to keep the line from becoming trapped under the spool.

6. Snap the hub cap and spring back on, and power the tool on. In a few seconds or less

you’ll hear the nylon line being cut automatically to the proper length.

OPTION 1: ACCESSORY REPLACEMENT SPOOL

Use Black & Decker replacement spool Model No. AF-100.

OPTION 2: REWINDING SPOOL USING BULK LINE

Bulk line for your trimmer/edger is available at extra cost from your local dealer or Black & Decker Service Center. To install bulk line, follow the steps below.

(Use .065” diameter ROUND line only)

1. Insert one end of the bulk line into the hole in the spool as shown in Figure 12 about 1/2”

(12 mm).

2. Hold the line in the hole and pull the rest of the line through the slot in the spool, shown in Figure 14.

3. Snugly and evenly wind the bulk line onto the spool in the direction of the arrow on the spool until the line builds up to the notches in the spool rim. (Fig. 14) Do not overfill spool. The spool holds 30 feet (10 m) of line.

MAINTENANCE

Be sure the tool is unplugged.

1. Keep the air intake slots (Figure 9) clean to avoid overheating.

2. Your trimmer line can dry out over time. To keep your line in top condition, store spare pre-wound spools or bulk line in a plastic, sealable bag with a tablespoon of water.

3. Plastic parts may be cleaned by using a mild soap and a damp rag.

4. DO NOT immerse tool in water or squirt it with a hose. DO NOT allow any liquid to get inside it.

5. Do not store the tool on or adjacent to fertilizers or chemicals.

6. DO NOT clean with a pressure washer.

7. The line cutter on the edge of the guard can dull over time. It is recommended you periodically touch-up the sharpness of the blade with a file.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

ACCESSORIES

Use Black & Decker replacement spool Model No. AF-100 and / or the cap and spring replacement Model No. RC100. Reload nylon line (either bulk or prewound replacement spool) as shown in this manual.

• USE ONLY .065” (1.65 mm) DIAMETER NYLON MONOFILAMENT LINE. Do not use

serated or heavier gauge line, as they will overload the motor and cause overheating. The unit only functions properly with 0.065” diameter nylon monofilament line. This line is available at your local dealer or authorized service center.

• WARNING: The use of any accessory not recommended by Black & Decker for use

with this tool could be hazardous.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986.

Full Two Year Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory and available on our website www.blackanddecker.com. This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. Free warning label replacement: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

Modèle GH600

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUE CE SOIT, COMPOSER LE

1-800-544-6986

AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LAPLUPART

DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR

TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS

IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.

ERCI

ERCIDD

’

AAVOIR

VOIR

CHOISI

LACK

& D

ECKER

ISITEZ

WWW

LACKAND

ECKER

COM

WNER

POUR

ENREGISTRER

VOTRE

NOUVEAU

PRODUIT

MODE D’EMPLOI

CCCCOOOOUUUUPPPPEEEE----BBBBOOOORRRRDDDDUUUURRRREE

+ 3 hidden pages