Black & Decker FS1800RS, 90503808 User Manual

• Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may create a risk of injury when used on another tool.

Service

• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel may result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of shock or injury.

SPECIFIC SAFETY RULES

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

• Use extra caution when cutting overhead and pay particular attention to overhead

wires which may be hidden from view. Anticipate the path of falling branches and debris ahead of time.

• KEEP HANDS AWAY from cutting area. Never reach underneath the material for any

reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers or thumb into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the saw by gripping the shoe.

• KEEP BLADES SHARP. Dull blades may cause the saw to swerve or stall under pres-

sure.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min ........................minutes ......................alternating current

......................direct current

o ........................no load speed

..........................

Class II Construction

........................

earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations

per minute

........................lock-on symbol ........................lock-off symbol

........................Quick Release lock-on symbol

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the battery is out of the tool or charger. Remove cap before placing battery in charger or tool.

WARNING: Do not store or carry battery so that metal objects can contact exposed

battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap. Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.

SAFETY WARNINGS AND INSTRUCTIONS: CHARGING THE SAW

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

3. CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs. Other types of batteries may burst causing personal injury and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed

extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdoor use can also be used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable for outdoor use.

b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size.

CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS NAMEPLATE RATING AMPS – 0 – 10.0

Total Extension Cord Length (ft) 25 50 75 100 125 150 Wire Gauge 18 18 16 16 14 14

9. Use only the supplied charger when charging your saw. The use of any other charger

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

CATALOG NUMBER

FS1800RS

INSTRUCTION

MANUAL

GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS

WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below, may result in electric shock, fire and/or seri-

ous personal injury.

SAVE THESE INSTRUCTIONS

Work Area

• Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.

Damaged cords may create a fire.

• A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. Acharger that may be

suitable for one type of battery may create a risk of fire when used with another battery.

• Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious

personal injury,

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

• Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery

pack into a tool with the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. Awrench or a key that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Atool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect battery pack from tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such

preventive safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

• When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may

cause sparks, burns, or a fire.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edge are less likely to bind and are easier to control.

11118888 VVVVoooolllltttt CCCCoooorrrrddddlllleeeessssssss RRRReeeecccciiiipppprrrrooooccccaaaattttiiiinnnngggg SSSSaaaaww

Battery Cap

KKKKEEEEYYYYIIIINNNNFFFFOOOORRRRMMMMAAAATTTTIIIIOOOONNNNYYYYOOOOUUUUSSSSHHHHOOOOUUUULLLLDDDDKKKKNNNNO

OOOWWWW::

• Keep shoe firmly against work surface.

• Charge battery for 9 hours before first use. For more information see “CHARGING

THE POWER PACK”.

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO

BLACK & DECKER.

HANK

YOU

FOR

CHOOSING

IREST

ORM

! G

OOTTO

WWW

IREST

ORMT

OOLS

COM

RODUCT

EGISTRA

TION

TTOOREGISTER

YOUR

NEW

PRODUCT

could damage the battery or create a hazardous condition.

10. Use only one charger when charging.

11. Do not attempt to open the charger or the saw. There are no customer serviceable

parts inside. Return to any authorized Black & Decker service center.

12. DO NOT incinerate the saw or battery packs even if they are severely damaged or

completely worn out. The batteries can explode in a fire.

13. A small leakage of liquid from the battery cells may occur under extreme usage, charg-

ing or temperature conditions. This does not indicate a failure. However, if the outer

seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10

minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-

35% solution of potassium hydroxide.

IMPORTANT CHARGING NOTES

1. After normal usage, your power pack should be fully charged in 3 to 9 hours. If the

power pack is run-down completely, it may take up to 9 hours to become fully charged.

Your power pack was sent from the factory in an uncharged condition. Before attempt-

ing to use it, it must be charged for at least 9 hours.

2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This

is important and will prevent serious damage to the power pack. Longest life and best

performance can be obtained if power pack is charged when air temperature is about

75°F.

3. While charging, the charger may hum and become warm to touch. This is a normal con-

dition and does not indicate a problem.

4. If the power pack does not charge properly—(1) Check current at receptacle by plug-

ging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light

switch which turns power off when you turn out the lights. (3) Move charger and power

pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and tem-

perature are

OK, and you do not get proper charging, take or send the power pack and charger to

your local Black & Decker service center. See Tools Electric in yellow pages.

5. The power pack should be recharged when it fails to produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE using saw with its power pack

in a depleted condition.

6. To prolong power pack life, avoid leaving the power pack on charge for extended periods

of time (over 30 days without use). Although overcharging is not a safety concern, it can

significantly reduce overall power pack life.

7. When the battery is inserted into the charger, the red “Charging Indicator” light will come

on indicating that there is contact between the battery and charger. The light will stay on

as long as the battery is in the charger and the charger is plugged into a working outlet. It

WILL NOT flash, go out or change to a different color when the charging cycle is

complete.

8. The power pack will reach optimum performance after being cycled 5 times during

normal usage. There is no need to run the batteries down completely before recharging.

Normal usage is the best method of discharging and recharging the batteries.

OPERATION

CAUTION: Always wear eye protection while operating this power tool.

NOTE: Before cutting any type of material, be sure it is firmly anchored or clamped to

prevent slipping.

• Place blade and shoe lightly against work to be cut.

• Switch on saw motor and allow it to obtain maximum speed before applying pressure.

• Always hold saw firmly with both hands while cutting as shown in Figure 1. Whenever possible, the saw shoe must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage.

TRIGGER SWITCH (FIGURE 2)

Release lock-off by switching to the unlocked position shown in Fig. 2 from either side of the saw. Pull the trigger switch to turn the motor ON. Releasing the trigger turns the motor OFF. NOTE: This tool has no provision to lock the switch in the ON position, and should never be locked in the ON position by any other means.

BLADE CLAMP RELEASE LEVER (FIGURE 3)

CAUTION: TURN OFF AND REMOVE BATTERY FROM TOOL.

To install blade into saw:

1. Open blade clamp release lever to its full open position as shown in Figure 3.

2. Insert blade shank from the front.

3. Close blade clamp release lever.

To remove blade from saw:

1. Open blade clamp release lever to its full open position.

2. Remove blade.

FLUSH CUTTING (FIGURE 4)

• The compact design of the reciprocating saw motor housing and pivoting shoe permit close cutting to floors, corners and other difficult areas.

• To maximize flush cutting capabilities, insert the blade shaft into the blade clamp with the teeth of the blade facing up.

• Turn the saw upside down so you are as close to the work surface as possible.

WOOD CUTTING (FIGURE 5)

• Before cutting any type of wood, be sure the work piece is firmly anchored or clamped to prevent slipping.

• Place blade and shoe lightly against work to be cut.

• Switch on saw motor before applying pressure.

• Always hold saw firmly with both hands while cutting. Whenever possible, the shoe must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage.

METAL CUTTING

• Use a finer blade for ferrous metals and a coarse blade for non-ferrous materials.

• In thin gauge sheet metals it is best to clamp wood to both sides of sheet. This will ensure a clean cut without excess vibration or tearing of metal.

• Avoid forcing cutting blade as this reduces blade life and causes costly blade breakage.

NOTE: You should spread a thin film of oil or other coolant along the line ahead of the saw cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

POCKET CUTTING - WOOD ONLY (FIGURE 6)

• Measure the surface area to be cut and mark clearly with a pencil, chalk or scriber.

• Insert pocket cutting blade in blade clamp and tighten blade clamp securely.

• Tip the saw backward until the back edge of the shoe is resting on the work surface.

• Switch motor on, permitting blade to attain maximum speed.

• Grip handle steadily and begin a slow, deliberate upward swing with the handle of the saw.

• The blade will begin to feed into material. Always be sure blade is completely through material before continuing with pocket cut.

NOTE: In areas where blade visibility is limited, use the edge of the shoe as a guide.

PROJECT TIPS

• Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while cutting.

• When cutting, always ensure that the shoe is resting against the workpiece. This will improve operator control and minimize vibration.

• For longer blade life, use bi-metal blades. These utilize a carbon steel back welded to high speed steel teeth making the blade more flexible and less prone to breaking.

TROUBLESHOOTING

Problem

Possible Cause Possible Solution

• Unit will not start. • Battery not installed properly. • Check battery installation.

• Battery not charged. • Check battery charging requirements.

• Battery will not charge. • Battery not inserted into charger. • Insert battery into charger until red LED appears.

• Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes”

for more details.

• Surrounding air temperature • Move charger and tool to

too hot or too cold. a surrounding air

temperature of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C).

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

MAINTENANCE REMOVE BATTERY FROM SAW WHEN PERFORMING ANY CLEANING OR OTHER

MAINTENANCE. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust etc.

• When electric tools are used on fiberglass boats, sports cars, drywall etc.,they are subject to accelerated wear and possible premature failure, as the fiberglass chips and grindings and drywall dust are highly abrasive to bearings, brushes, commutator, etc. During any use on fiberglass or drywall it is extremely important that the tool be cleaned frequently by blowing with an air jet.

LUBRICATION

Your tool was properly lubricated before leaving the factory. Once every year take or send your tool to a Black & Decker service center, or authorized service station, for a complete cleaning, inspection and lubrication. Tools "out of service" for long periods should be relubricated before being put back to work.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts

ACCESSORIES

The FS1800RS FIRESTORM

reciprocating saw will accept up to a 12 inch long blade. Always use the shortest blade suitable for your project. Longer blades are more likely to be bent or damaged during use. During operation some longer blades may vibrate or shake if the saw is not kept in contact with the workpiece.

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-54-HOW-TO. (800-544-6986)

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickelcadmium batteries. Help protect our environment and conserve natural resources by returning the spent nickel-cadmium battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call 1-800-8-BATTERY.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-54-HOW TO (544-6986).

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after

ROCK TOOL UP TO NORMAL CUTTING POSITION AFTER BLADE HAS CUT THROUGH MATERIAL BERCER L’OUTIL EN POSITION NORMALE DE COUPE ÁPRES AVOIR TRAVERSÉ MATÉRIAU AVEC LA LAME. BALANCEE LA HERRAMIENTA HASTA LA POSICION DE CORTE NORMAL DESPUES DE HACER EL CORTE A

TRAVES DEL MATERIAL

STARTING POSITION FOR POCKET CUTTING POSITION DE DÉPART POUR LES COUPES EN RETRAIT POSICION DE INICIO PARA EL CORTE DE BOLSILLO

FS1800RS tool can accept any of the following 18V slide pack batteries and 18V slide pack chargers seen in the chart below. Please see the individual charger manuals for all safety and operating instructions.

18V Slide Pack Batteries

18V Firestorm Battery 18V FSXtreme Battery 18V FSXtreme Battery 3 terminal 18V FSXtreme Battery Silver Series 18V Black & Decker Battery

FSB18 FS180BX FS18BX

FS18SBX

HPB18

Cat. # Description

18V Slide Pack Chargers

18V Cup Charger 18V Dual Port Charger 18V Radio Charger 18V Three Port Charger

9.6V-18V Fast Charger

9.6V-24V One Hour Charger

9.6V-24V Dual Port One Hour Charger

FS18C FS180DC FS18RC 5104211-00 FSMVC FS240FC FS2400DC

Cat. # Description

les cordons endommagés. Les cordons endommagés augmentent les risques de secousses électriques.

• Lorsqu’on utilise un outil électrique à l’extérieur, se servir d’un cordon de rallonge prévu pour l’extérieur, portant la mention “W-A” ou “W”. Ces cordons sont conçus

pour servir à l’extérieur et minimisent les risques de secousses électriques.

SÉCURITÉ PERSONNELLE

• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu’on utilise un outil électrique. Ne pas s’en servir lorsqu’on est fatigué ou affaibli par des drogues, de

l’alcool ou des médicaments. De graves blessures peuvent résulter d’un moment d’inattention lors de l’utilisation d’un outil électrique.

• Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des bijoux. Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les vêtements et

les gants des pièces en mouvement qui peuvent les happer.

• Éviter les démarrages accidentels. S’assurer que l’interrupteur est en position hors tension avant de brancher l’outil. Afin d’éviter les risques de blessures, ne pas

transporter l’outil avec le doigt sur l’interrupteur ni brancher un outil dont l’interrupteur est en position sous tension.

• Enlever les clés de réglage avant de mettre l’outil sous tension. Une clé qui est laissée sur une pièce rotative de l’outil présente des risques de blessures.

• Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s’assure d’une meilleure maîtrise de l’outil dans des situations imprévues grâce à une position stable et un bon équilibre.

• Porter de l’équipement de sécurité. Toujours porter des lunettes de sécurité. Dans certaines conditions, il faut porter des masques respiratoires, des chaussures antidérapantes, un casque de sécurité ou des protège-tympans.

UTILISATION ET ENTRETIEN DE L’OUTIL

• Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de soutenir la pièce à ouvrer sur une plate-forme stable. La pièce est instable lorsqu’elle

est retenue par la main ou le corps de l’utilisateur. Cela présente des risques de perte de maîtrise de l’outil.

• Ne pas forcer l’outil. Utiliser l’outil approprié à la tâche. L’outil approprié fonctionne mieux et sûrement lorsqu’on s’en sert à son rendement nominal.

• Ne pas se servir de l’outil lorsque l’interrupteur est défectueux. Le cas échéant, l’outil est dangereux et il faut le réparer.

• Débrancher l’outil de la source d’alimentation avant de le régler, d’en remplacer les accessoires ou de le ranger. On minimise de la sorte le risque de démarrage accidentel

de l’outil.

• Ranger l’outil hors de portée des enfants et de toute autre personne qui n’en connaît pas le fonctionnement. L’outil est dangereux entre les mains de ces personnes.

• Prendre soin des outils. S’assurer que les outils de coupe sont tranchants et propres. Des outils bien entretenus à arêtes tranchantes ont moins tendance à se coincer

et ils se maîtrisent mieux.

• Vérifier l’alignement et les attaches des pièces mobiles, le degré d’usure des pièces ainsi que tout autre facteur susceptible de nuire au bon fonctionnement de l’outil.

Faire réparer un outil endommagé avant de s’en servir. Des outils mal entretenus sont la cause de nombreux accidents.

• Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires qui conviennent à un outil peuvent présenter des risques avec un autre outil.

ENTRETIEN

• Confier l’entretien de l’outil seulement à du personnel qualifié. Le non-respect de la présente directive présente des risques de blessures.

• Lors de l’entretien de l’outil, utiliser seulement des pièces de rechange identiques.

Respecter les consignes relatives à l’entretien du présent guide d’utilisation. Il y a risque de secousses électriques ou de blessures lorsqu’on utilise des pièces non autorisées ou lorsqu’on ne respecte pas les consignes relatives à l’entretien.

CONSIGNES DE SÉCURITÉ PARTICULIÈRES

• Tenir l’outil par les surfaces isolées prévues à cette fin lorsqu’il risque d’entrer en

contact avec des fils cachés ou son propre cordon, car de tels contacts peuvent

mettre les pièces métalliques de l’outil sous tension, engendrant des risques de choc électrique.

• Faire preuve d’une grande prudence en réalisant des coupes à bout de bras afin d’éviter les fils électriques aériens cachés. Anticiper la direction dans laquelle les branches coupées et les débris se détacheront et tomberont au sol.

• Garder les mains éloignées des zones de coupe. Ne pas mettre les mains sous la pièce

pour quelque raison que ce soit. Saisir la section profilée à l’avant de l’outil. Ne pas mettre les doigts ou le pouce près de la lame à va-et-vient ni de sa bride de serrage. Ne pas stabiliser la scie en saisissant le patin.

• Maintenir les lames bien aiguisées en tout temps; les lames usées peuvent faire dévier la scie ou faire caler le moteur lorsqu’on exerce une pression sur l’outil.

• Saisir les surfaces isolées de l'outil lorsqu'on s'en sert là où il pourrait y avoir des fils sous tension et lorsqu'il pourrait entrer en contact avec son propre fil. En cas de

contact avec un fil sous tension, les composantes métalliques à découvert de l'outil deviendraient sous tension et l'utilisateur subirait des secousses électriques.

AVERTISSEMENT : Certains outils électriques, tels que les sableuses, les scies, les meules, les perceuses ou certains autres outils de construction, peuvent produire de la poussière contenant des produits chimiques susceptibles d’entraîner le cancer, des malformations congénitales ou pouvant être nocifs pour le système reproductif. Parmi ces produits chimiques, on retrouve :

• le plomb dans les peintures à base de plomb,

• la silice cristalline dans les briques et le ciment et autres produits de maçonnerie,

• l’arsenic et le chrome dans le bois de sciage ayant subi un traitement chimique (comme l’arséniate de cuivre et de chrome).

Le risque associé à de telles expositions varie selon la fréquence avec laquelle on effectue ces travaux. Pour réduire l’exposition à de tels produits, il faut travailler dans un endroit bien aéré et utiliser le matériel de sécurité approprié, tel un masque anti-poussières spécialement conçu pour filtrer les particules microscopiques.

• Éviter tout contact prolongé avec la poussière soulevée par cet outil ou autres outils électriques. Porter des vêtements de protection et nettoyer les parties exposées du corps à l’eau savonneuse. S’assurer de bien se protéger afin d’éviter

d’absorber par la bouche, les yeux ou la peau des produits chimiques nocifs.

AVERTISSEMENT : Cet outil peut produire et répandre de la poussière susceptible

de causer des dommages sérieux et permanents au système respiratoire. Toujours

utiliser un appareil respiratoire anti-poussières approprié approuvé par le NIOSH ou l’OSHA. Diriger les particules dans le sens opposé du visage et du corps.

MISE EN GARDE : porter un dispositif de protection personnel anti-bruit approprié

durant l’utilisation. Sous certaines conditions et pendant toute la durée de l’utilisation, le

bruit émanant de ce produit pourrait contribuer à la perte d’audition.

AVERTISSEMENT : Ne pas utiliser cet outil pendant des périodes prolongées. Les

vibrations causées par l’action de fonctionnement de l’outil peuvent blesser en permanence les doigts, les mains et les bras. Porter des gants pour amortir les vibrations, faire des pauses fréquentes et limiter le temps d’utilisation quotidien de l’outil.

L’étiquette de l’outil peut comporter les symboles suivants.

V ....................................volts A..........................ampères

Hz ..................................hertz W ........................watts

min..................................minutes ......................courant alternatif

................................courant continu

o ........................sous vide

....................................

Construction de classe II

............................

borne de mise à la

minute

....................................symbole d´avertissement .../min ..................tours ou courses

à la minute

..................................Symbole de verrouillage en position d’arrêt

..................................Symbole de verrouillage en position de marche

..................................Symbole de déverrouillage rapide de la position de marche

INFORMATION CONCERNANT LE CAPUCHON DU BLOC-PILE

Un capuchon est fourni avec le bloc-pile en vue d’être utilisé chaque fois qu’on retire ce dernier de l’outil ou du chargeur en vue de le ranger ou de le transporter; enlever le capuchon avant de remettre le bloc-pile dans le chargeur ou dans l’outil.

RÈGLES DE SÉCURITÉ GÉNÉRALES CONCERNANT LES

OUTILS À PILES

AVERTISSEMENT : LIRE, COMPRENDRE ET SUIVRE TOUTES LES DIRECTIVES

précisées ci-dessous afin d’éviter les risques de choc électrique, d’incendie ou de blessure grave.

ZONE DE TRAVAIL

• S’assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et

des endroits sombres présentent des risques d’accidents.

• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme celles dégagées par des liquides, des gaz ou des poussières inflammables). Les

étincelles générées par le moteur des outils électriques peuvent enflammer les poussières ou les vapeurs.

• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu’on utilise un outil électrique. Une distraction peut entraîner la perte de maîtrise de l’outil.

MESURES DE SÉCURITÉ RELATIVES À L’ÉLECTRICITÉ

• Les outils à double isolation comportent une fiche polarisée (une lame plus large que l’autre). La fiche n’entre que d’une façon dans une prise polarisée. Lorsque la fiche n’entre pas à fond dans la prise, essayer de nouveau après avoir inversé les broches de la fiche. Si la fiche n’entre toujours pas dans la prise, communiquer avec un électricien certifié afin de faire installer une prise polarisée. Ne modifier en aucune façon la fiche. La double isolation élimine le besoin d’un cordon trifilaire mis à la terre et d’un système d’alimentation mis à la terre.

• Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs, des cuisinières et des réfrigérateurs. Les risques sont alors plus élevés si le corps de

l’utilisateur est mis à la terre.

• Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration d’eau dans l’outil augmente les risques de secousses électriques.

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter l’outil ni tirer sur le cordon pour débrancher l’outil. Éloigner le cordon des sources de chaleur, des flaques d’huile, des arêtes tranchantes et des pièces mobiles. Remplacer immédiatement

the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "ToolsElectric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center.

SPECIAL WARRANTY NOTE TO CONTRACTORS:

FIRESTORM

branded products are offered as high end consumer home use tools and

carry a HOME USE WARRANTY. These tools are designed, manufactured and tested to meet or exceed the needs of the do-it-yourselfer in the execution of projects and repairs in and around the home. With proper use they will provide the home owner with step up power and performance well beyond their two year warranty. However, if you use tools for a living and use FIRESTORMTMbranded products or any of Black & Decker’s other Consumer Home Use tools ON THE JOBSITE you should know that they CANNOT BE COVERED

UNDER OUR WARRANTY.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

IIIIMMMMPPPPOOOORRRRTTTTAAAANNNNTTTTSSSS RRRREEEENNNNSSSSEEEEIIIIGGGGNNNNEEEEMMMMEEEENNNNTTTTSSSS ::

• Garder le patin fermement contre la surface de travail.

• Charger la pile pendant 9 heures avant d’utiliser l’outil pour la première fois. Pour obtenir plus d’information, vois la section « CHARGEMENT DU BLOC-PILE ».

SSSScccciiiieeee aaaalllltttteeeerrrrnnnnaaaattttiiiivvvveeee ssssaaaannnnssss ffffiiiillll ddddeeee 11118888 vvvvoooollllttttss

Numéro de catalogue

FS1800RS

GUIDE D’UTILISATION

CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUE CE SOIT, COMPOSER LE

1-800-544-6986

AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART

DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR

TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS

IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.

ERCI

ERCIDD

’

AAVOIR

VOIR

CHOISI

IREST

ORM

! V

ISITEZ

WWW

IREST

ORMT

OOLS

COM

RODUCT

EGISTRA

TION

POUR

ENREGISTRER

VOTRE

NOUVEAU

PRODUIT

+ 4 hidden pages