Black & Decker 608435-00 User Manual

TO REDUCE RISK OF INJURY:

• Before any use, be sure everyone using this tool reads and understands all safety instructions and other information contained in this manual.

• Save these instructions and review frequently prior to use and in instructing others.

WARNING: When using an electric appliance, basic safety precautions should always be followed

to reduce risk of fire, electric shock, and personal injury, including the following.

WARNING: Some dust created by this product contains chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber

To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.

WARNING: This product contains chemicals, including lead, known to the State of California to

cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and

duration of use, noise from this product may contribute to hearing loss.

READ ALL INSTRUCTIONS BEFORE USING BLOWER.

• READ and follow all instructions.

• DO NOT place inlet or outlet of vacuum near eyes or ears when operating.

• THIS APPLIANCE IS PROVIDED WITH DOUBLE INSULATION. Use only identical replacement parts. See instructions for servicing of double insulated appliances.

• STORE IDLE TOOLS. When not in use, the unit should be stored in a dry, high or locked-up place - out of reach of children.

• DON'T OVERREACH. Keep proper footing and balance at all times.

• DO NOT pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

• MAINTAIN TOOL WITH CARE. Keep fan area clean for best and safest performance. Follow instructions for proper maintenance.

• DO NOT attempt to repair the blower/vac. To assure product safety and reliability, repairs, maintenance, and adjustments should be performed by Black & Decker service centers or authorized service stations, always using Black & Decker replacement parts.

• DO NOT operate blower/vac in a gaseous or explosive atmosphere. Motors in these tools normally spark, and the sparks might ignite fumes.

• DO NOT use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.

• USE EXTRA CARE when cleaning on stairs.

• DO NOT leave appliance when plugged in. Unplug from outlet when not in use and before servicing.

• DO NOT allow to be used as a toy. Close attention is necessary when used by or near children. Not recommended for use by children.

• DO NOT attempt to clear clogs from tool without first unplugging it.

• USE ONLY as described in this manual. Use only manufacturer's recommended attachments.

• DO NOT use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.

• DO NOT pull or carry by cord, use cord as a handle, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.

• DO NOT unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• DO NOT put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair and everything that may reduce air flow.

• KEEP hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• TURN OFF all controls before unplugging.

• DO NOT vacuum water, other liquids, or wet objects such as leaves. Never immerse any part of the tool in liquid.

• DO NOT handle plug or appliance with wet hands.

• KEEP CHILDREN, BYSTANDERS AND ANIMALS AWAY from the work area a minimum of 30 feet (10 meters) when starting or operating the tool.

• INSPECT THE AREA before using the tool. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. As a vacuum, the tool is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc.

WARNING: To reduce the risk of electrical shock; do not expose to rain, do not use on wet surfaces.

Store indoors.

WARNING: Tu rn off and unplug unit, then wait until fan stops or at least 10 seconds before removing the blower or

vacuum tube assemblies.

SAVE THESE INSTRUCTIONS

Your Blower/Vac is double-insulated to give you added safety. In a double insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double insulated appliance requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double insulated appliance must be identical to the parts they replace. A double insulated appliance is marked with the words double insulated or "double insulation". The symbol (square within a square) may also be marked on the appliance.

Double insulated tools have 2-wire cords and can be used with 2-wire or 3-wire extension cords. Only round jacketed extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.) (C.S.A. in Canada). If the extension will be used outside, the cord must be suitable for outdoor use. Any cord marked as outdoor can also be used for indoor work.

An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size.

To determine the minimum wire size required, refer to the chart below. Before using an extension cord, inspect it for loose or exposed wires, damaged insulation, and defective fittings. Make any needed repairs or replace the cord if necessary.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Catalog Number BV2500,

KEY INFORMATION YOU SHOULD KNOW:

• Before operating, make sure that either the blower or vacuum tube assembly is locked in place.

• The power switch must be OFF in order to depress the release button for changing blower and vacuum tube assemblies.

Release Button

Bouton de Dégagement

Botones de Liberación

Blowing Mode

Souffleuse

Modo de Soplador

ON En Marche Encendido

OFF

Arrêt

Apagada

Vacuuming Mode

Aspirateur

Modo de Aspiradora

Extension Tube

Tube de Rallange

Tubo de Extension

Vacuum Tube

Tube D´Aspiration

Tubo de Aspirado

DATE CODE

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO (544-6986)

IF YOU SHOULD EXPERIENCE APROBLEM

WITH YOUR BLACK &DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986)

BEFORE YOU CALL, HA VE THE FOLLOWING INFORMATION AV AILABLE, CATALOG No., TYPE

No., AND DATE CODE. IN MOSTCASES, ABLACK & DECKER REPRESENT A TIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGESTION OR

COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.

Switch

Interrupteur

Interruptor

WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS

SERVICING OF DOUBLE INSULATED APPLIANCES

SAFETY RULES AND INSTRUCTIONS: EXTENSION CORDS

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage Than Than

0- 6 18 16 16 14 6- 10 18 16 14 12 10- 12 16 16 14 12 12- 16 14 12 Not Recommended

INSTRUCTION

MANUAL

BV9000

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This equipment must be used with a suitable polarized 2 wire or 3 wire extension cord. Polarized connections will fit together only one way. Make sure that the receptacle end of the extension cord has large and small blade slot widths. If the plug does not fit fully into the extension cord, reverse the plug. If it still does not fit, obtain a suitable extension cord. If the extension cord does not fit fully into the outlet, contact a qualified electrician to install the proper outlet. Do not change the tool plug or extension cord in any way.B

EFORE OPERATING

• SECURING POWER SUPPLY CORD - Secure the extension cord in the tool's built-in cord retainer as shown in Figure 12 or

secure the power supply cord and a suitable extension cord as shown in Figure 13.

SWITCH

NOTE: The switch will not operate if the release button, shown in Figure 1, is depressed.

To turn the tool ON, slide the switch forward, as shown in Figure 1. To turn tool OFF, slide switch to the rear.

OPERATION

USE AS A BLOWER: ALWAYS WEAR SAFETY GLASSES, WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY.

• BLOWER MODE

Ensure that the unit is switched OFF and is disconnected from the power supply. Assemble blow tube as shown in Figure 2. (This only needs to be done the first time you assemble the unit.)

WARNING: When turning the tool off for tube installation or any other reason, wait 10 seconds for the fan to stop

rotating before disassembly.

Attach the blower tube assembly (The assembly includes the blower tubes, the fan chamber and the blower air speed control mechanism) to the front of the tool, as shown in Figure 3 by inserting point A into the matching recess marked point B, also shown in Figure 3. Swing the tube up to engage the lock, as shown in Figure 4.

NOTE: The lock will not engage if the ON/OFF switch is in the forward (ON) position.

Hold the end of the blower tube approximately 7 inches (180mm) above the ground and turn the tool ON. Using a sweeping motion, from side to side, advance slowly keeping the accumulated debris (leaves,grass clippings etc.) in front of you, as shown in Figure 5. Once you have blown the debris into a pile, you can convert to vacuum mode to collect the debris for disposal.

• BLOWER AIR SPEED CONTROL

Your Blower Vac has a variable air speed feature that allows you to select the air speed that best fits your needs. To adjust the air speed, simply slide the orange collar. This will allow movement over the full range of

1 3/4"(44.5mm).With the slide collar in the "A" position, as shown in Figure 6, the maximum blower speed will be 200 mph (320 kph). When pushed forward to position "C" ( as far from the tool housing as possible; about 1 3/4"{44.5mm}) the speed will be approximately 140 mph (225 kph). Position "B" (midway between the two) permits infinite adjustment between positions "A" and "C". A little practice will help you determine what is the best speed for your application.

USE AS A VACUUM CLEANER: ALWAYS WEAR SAFETY GLASSES. WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY.

• REMOVING THE BLOWER TUBE ASSEMBLY

Switch off the unit and unplug from the outlet. To disconnect the blower tube assembly from the tool, depress the release button, shown in Figure 1, ensuring that the tube

does not fall to the ground.

NOTE: The release button will not depress if the ON/OFF switch is in the forward (ON) position.

•VACUUMING MODE

Ensure that the unit is switched off and disconnected from the power supply. Position the vacuum tube and extension tube as shown in Figure 7. Push the extension tube into the vacuum tube until it snaps into place and the arrows shown in Figure 7A are covered as in Figure 7B. If necessary, this can be made easier by wiping the end of the extension tube with a cloth dampened with soapy water only.

Attach the vacuum tube assembly (The assembly includes the extension tube, the vacuum tube and the fan chamber.) to the front of the tool. Insert point "A", shown in Figure 8, into the matching recess in the front of the tool point "B", also shown in Figure 8, and swing the tube up to engage the lock, as shown in Figure 9.

Attach the collection bag to the vacuum outlet using the bayonet fitting, as shown in Figure 10. Hold the vacuum as shown in Figure 11. Tilt the vacuum tube slightly and use a sweeping action similar to the action described

under Blower Mode. The light debris will flow into and through the vacuum tube into the collection bag. Things such as leaves and small twigs will be mulched as they pass through the fan chamber so that the collection bag will hold a lot of debris.

When the collection bag gets full, suction will noticeably decrease. Turn off and unplug the tool and unzip the bag to empty before continuing to operate.

CAUTION: NEVER UNZIP THE COLLECTION BAG WITHOUT FIRST TURNING OFF AND UNPLUGGING THE

VACUUM.

NOTE: If the suction decreases and the bag is not full, the vacuum tube is probably clogged with debris. Turn off and

unplug the vacuum and clear the tube before continuing.

MAINTENANCE

• CLEANING AND STORAGE TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.)

Use only mild soap and a damp cloth to clean the tool. Clean out any clippings which may have accumulated in the Blower/Vac. When used properly with dry leaves the fan chamber of your Blower/Vac should remain clean. If damp earth and debris are ingested some of the particles may build up on the inside of the fan chamber. If this happens the performance of the unit will decrease. This area can be cleaned out by gently wiping out with a damp rag after disconnecting from the power source. Your Blower/Vac should be stored in a dry place.

CAUTION

DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN.

Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts. Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the

tool into a liquid.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-54-HOW-TO (544-6986).

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

Leaf Collection System Cat. No. BV-006 (Available from your dealer at extra cost.) (BV-006 is included with BV9000). The Leaf Collection System replaces the collection bag with a system of collecting debris directly into a 30-33 gallon trash can.

Complete directions for the system’s use are included. (Trash can not included.)

IMPORTANT

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you.

To find your local service location, refer to the yellow page directory under “Tools—Electric” or call: 1-800-54-HOW-TO (544-6986).

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways:

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under “Tools-Electric” in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center.

This product is not intended for commercial use.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE

LA RAISON, PRIÈRE DE COMPOSER

1 800 544-6986.

RENSEIGNEMENTS IMPORTANTS

• Avant de faire fonctionner l’outil, s’assurer que le souffleur ou l’assemblage du tube d’aspiration soit bien enclenché.

• Mettre l’interrupteur en position d’arrêt («OFF») avant d’enfoncer le bouton de déclenchement en vue de remplacer l’assemblage du souffleur ou du tube d’aspiration.

SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUG

BEFORE OPERATING

AVERTISSEMENT : IMPORTANTES MESURES DE SÉCURITÉ

AFIN DE RÉDUIRE LES RISQUES DE BLESSURES :

•Avant toute utilisation, s’assurer que tous ceux qui se servent de l’outil lisent et comprennent toutes les mesures de sécurité et tout autre renseignement contenus dans le présent guide.

• Conserver ces mesures et les relire fréquemment avant d’utiliser l’outil ou d’en expliquer le fonctionnement à d’autres personnes.

AVERTISSEMENT : Afin de réduire les risques d’incendie, de secousses électriques ou de blessures

lorsqu’on utilise des outils électriques, il faut toujours respecter les mesures de

sécurité suivantes.

AVERTISSEMENT : Le produit génère de la poussière qui peut renfermer des produits chimiques.

Selon l’état de la Californie, ces produits chimiques peuvent causer le cancer ainsi que des malformations congénitales, et ils présentent d’autres dangers au système reproductif humain. Voici des exemples de tels produits chimiques :

• les composés d’engrais;

• les composés d’insecticides, d’herbicides et de pesticides;

• l’arsenic et le chrome provenant de bois traité. Afin de minimiser les risques, porter de l’équipement de sécurité approuvé comme des masques antipoussières spécialement conçu pour filtrer les particules microscopiques.

AVERTISSEMENT : Le produit renferme des produits chimiques, dont du plomb. Selon l’état de la

Californie, ce produit chimique peut causer le cancer ainsi que des malformations congénitales, et il présente d’autres dangers au système reproductif humain. Se laver les mains après l’utilisation.

MISE EN GARDE : Porter un dispositif approprié de protection de l’ouïe lors de l’utilisation du

produit. Dans certaines conditions et durées d’utilisation, le produit peut émettre un niveau de bruit provoquant la perte de l’ouïe.

LIRE TOUTES LES DIRECTIVES AVANT D’UTILISER L’OUTIL.

MESURES DE SÉCURITÉ POUR TOUS LES OUTILS•

• LIRE et respecter toutes les mesures de sécurité.

• NE PAS porter l’entrée ou la sortie du tube de l’aspirateur à proximité des yeux ou des oreilles lorsque l’outil fonctionne.

• L’OUTIL EST MUNI D’UNE DOUBLE ISOLATION. Utiliser seulement des pièces de rechange identiques. Voir les directives sur

l’entretien des outils à double isolation.

• RANGER LES OUTILS NON UTILISÉS dans un endroit sec, situé en hauteur ou fermé à clé, hors de portée des enfants.

• NE PAS DÉPASSER SA PORTÉE. Toujours demeurer dans une position stable et garder son équilibre en tout temps.

• NE PAS aspirer d’objets en combustion tels les mégots de cigarette, des allumettes ou des cendres chaudes.

• BIEN ENTRETENIR L’OUTIL. Garder le ventilateur propre afin d’optimiser et de sécuriser le rendement. Suivre les directives

d’entretien.

• NE PAS tenter de réparer l’outil. Pour garantir la sécurité et la fiabilité du produit, les réparations, en confier l’entretien et les

réglages à un centre de service Black & Decker ou à un atelier d’entretien autorisé utilisant uniquement des pièces de rechange Black & Decker.

• NE PAS utiliser l’outil dans des endroits où l’atmosphère renferme des vapeurs combustibles ou explosives. Les étincelles que

produit habituellement le moteur en marche pourraient enflammer ces produits.

• NE PAS se servir de l’outil pour ramasser des liquides inflammables ou combustibles (comme de l’essence) ni l’utiliser dans

des endroits où de tels produits peuvent se trouver.

• FA IRE TRÈS ATTENTION lorsqu’on travaille dans des escaliers.

• NE PAS laisser l’outil branché sans surveillance. Le débrancher lorsqu’on ne s’en sert pas et avant d’en faire l’entretien.

• IL NE S’AGIT PAS d’un jouet. Faire particulièrement attention lorsqu’un enfant utilise l’outil ou qu’on s’en sert près d’un enfant.

Il est déconseillé de laisser un enfant se servir de l’outil.

• NE PAS tenter de débloquer l’outil avant de le débrancher.

• UTILISER SEULEMENT L’OUTIL de la manière prescrite dans le présent guide. Utiliser uniquement les accessoires

recommandés par le fabricant.

• NE PAS utiliser lorsque le cordon ou la fiche sont endommagés. Confier l’outil à un centre de service lorsqu’il ne fonctionne

pas convenablement, lorsqu’il est tombé ou endommagé, lorsqu’il a été laissé à l’extérieur ou lorsqu’il est tombé à l’eau.

• NE PAS tirer sur le cordon ni se servir du cordon pour transporter l’outil. Ne pas tirer sur le cordon près d’arêtes tranchantes

ou de coins. Éloigner le cordon de toute surface chauffée.

• NE PAS débrancher l’outil en tirant sur le cordon. Pour le débrancher, en saisir la fiche et non le cordon.

• NE RIEN insérer dans les ouvertures. Ne pas utiliser l’outil lorsqu’une ouverture est bouchée; garder les ouvertures exemptes

de poussière, de charpie, de cheveux et de tout ce qui peut réduire le débit d’air.

• ÉLOIGNER les cheveux, les vêtements amples, les doigts et le corps des ouvertures ainsi que des pièces mobiles.

• METTRE TOUTES LES COMMANDES HORS FONCTION avant de débrancher l’outil.

• NE PAS utiliser pour aspirer de l’eau, tout autre liquide ou des objets mouillés comme des feuilles. Ne jamais immerger l’outil,

au complet ou en partie.

• NE PAS manipuler la fiche ni l’outil avec les mains mouillées.

• S’ASSURER QUE LES ENFANTS, LES OBSERVATEURS ET LES ANIMAUX SE TROUVENT À UNE DISTANCE minimale de

10 mètres (30 pieds) de la surface de travail lorsqu’on démarre l’outil ou qu’on s’en sert.

• EXAMINER LA ZONE avant d’utiliser l’outil. Enlever tout débris ou objet dur (comme des pierres, du verre, des fils) qui peut

ricocher, être éjecté ou provoquer des blessures ou des dommages lors de l’utilisation de l’outil. Lorsqu’on se sert de l’outil pour aspirer, celui-ci est conçu pour ramasser des matériaux secs (comme des feuilles, de l’herbe, de petites branches et des bouts de papier). Ne pas aspirer des roches, du gravier, du métal, du verre cassé ou d’autres objets semblables.

AVERTISSEMENT : Afin de minimiser les risques de secousses électriques, protéger de la pluie, ne pas s’en servir

sur des surfaces mouillées et ranger à l’intérieur.

AV ERTISSEMENT : Arrêter et débrancher l’appareil. Attendre au moins 10 secondes ou jusqu’à ce que le

ventilateur s’arrête complètement avant de retirer l’assemblage du souffleur ou du tube d’aspiration.

CONSERVER CES MESURES.

ENTRETIEN DES OUTILS À DOUBLE ISOLATION

La souffleuse-aspirateur à double isolation procure une protection supplémentaire. Dans ce type d’outil, les deux systèmes d’isolant remplacent la mise à la terre. Il n’y a aucun moyen de mettre l’outil à la terre et aucun système de mise à la terre ne doit être ajouté à l’outil. L’entretien d’un outil à double isolation exige beaucoup de soin et une excellente connaissance du système; il ne devrait être confié qu’à un technicien compétent. Les pièces de rechange de ce type d’outil doivent être identiques aux pièces d’origine. Un outil à double isolation porte l’inscription «DOUBLE INSULATED» ou «DOUBLE INSULATION». Le symbole (un carré à l’intérieur d’un carré) peut aussi figurer sur l’outil.

MESURES DE SÉCURITÉ : CORDONS DE RALLONGE

Les outils à double isolation sont munis d’un cordon bifilaire et ils peuvent être utilisés avec un cordon de rallonge muni de 2 ou de 3 fils. Il faut seulement utiliser des cordons de rallonge à gaine ronde et ils devraient être homologués par l’organisme américain Underwriters Laboratories (U.L.) ou la CSA (au Canada). Lorsque le cordon de rallonge est utilisé à l’extérieur, il doit être prévu à cet effet. Tout cordon extérieur peut servir à l’intérieur.

Les cordons de rallonge doivent être faits de conducteurs de calibre approprié (AWG ou jauge américaine des fils) par mesure de sécurité et afin de prévenir les pertes de puissance et les surchauffes. Le numéro de calibre du fil est inversement proportionnel à la capacité du cordon. Ainsi, un cordon de calibre 16 a une capacité supérieure à un cordon de calibre 18. Lorsqu’il est nécessaire d’utiliser plus d’un cordon de rallonge, veiller à ce que chaque cordon ait au moins le calibre minimal.

Le tableau ci-dessous permet de déterminer le calibre minimal des cordons.Avant d’utiliser un cordon de rallonge, s’assurer qu’il n’y a pas de fils dénudés ni détachés, et que l’isolant et les raccords ne sont pas défectueux. Effectuer les réparations nécessaires ou remplacer le cordon, le cas échéant.

Calibre minimal des cordons de rallonge

Tension Longueur totale du cordon en pieds

120 V De 0 à 25 De 26 à 50 De 51 à 100 De 101 à 150 240 V De 0 à 50 De 51à 100 De 101 à 200 De 201 à 300

Intensité (A) Au Au Calibre moyen de fil (AWG)

moins plus

0-6 18 16 16 14 6-10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Non recommandé

GUIDE D’UTILISATION

+ 2 hidden pages