Black & Decker 4060, 4063, 4025, 386312-02, 4063SD User Manual

GRB/386312-02 8/11/00 1:56 PM Page 1

GRABBER Construction Products, 205 Mason Circle, Concord, CA 94520

GRB/386312-02 8/11/00 1:56 PM Page 2

GRABBER

INSTRUCTION MANUAL GUIDE D'UTILISATION MANUAL DE INSTRUCCIONES

GRABBER

ROCKER 4025/4060/4063/4063SD Scrudrivers Tournevis Destornilladores

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

ROCKER ScruDrivers

GRB/386312-02 8/11/00 1:56 PM Page 3

English

change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Applicable only to Class II (double insulated) tools. The 4060 and 4063 units are double insulated.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools

or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W.” These cords are rated for

outdoor use and reduce the risk of electric shock. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than 0-6 18161614 6 - 10 18 16 14 12 10-1216161412 12 - 16 14 12 Not Recommended

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use tool while tired or

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY GRABBER TOOL, CALL US TOLL FREE AT:

1-800-477-TURN (1-800-477-8876)

General Safety Rules

WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to carry electricity away from the user. Applicable only to Class I

(grounded) tools.

• Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not

GRB/386312-02 8/11/00 1:56 PM Page 4

under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury,

• Dress properly. Do not wear loose clothing or jewelry. Contain

long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught

in moving parts.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or switches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or

against your body is unstable and may lead to a loss of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer and the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.

English

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage

of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified

personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts.

Follow instructions in the Maintenance section of this manual.

Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

Additional Safety Rules

• Hold tool by insulated gripping surfaces when performing an

operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

• Keep handles dry, clean, free from oil and grease. It is recommended to use rubber gloves. This will enable better control

• DO NOT TOUCH ANY METAL PARTS OF THE TOOL when

drilling or driving into walls, floors or wherever live electrical wires may be encountered. Hold the tool only by insulated

grasping surfaces to prevent electric shock if you drill or drive into a live wire.

GRB/386312-02 8/11/00 1:56 PM Page 1

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. T o reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

The label on your tool may include the following symbols.

V ....................................volts

A ....................................amperes

Hz ..................................hertz

W ....................................watts

min..................................minutes

..................................alternating current

................................direct current

o....................................no load speed

....................................

Class II Construction

…/min..............................revolutions or reciprocation per minute

....................................earthing terminal

....................................safety alert symbol

Switch

To start tool, depress the trigger switch, shown in Figure 1. To stop tool, release the switch. The variable speed trigger switch permits speed control. The farther the trigger switch is depressed, the higher the speed of the tool.

English

FIG. 2

BIT

BALL GROOVE

1/4" HEX

DRIVE

BALL

RETAINER

REVERSING

LEVER

TRIGGER

SWITCH

LOCKING

BUTTON

FIG. 1

FIG. 3

DEPTH

LOCATOR

ADJUSTMENT

COLLAR

BIT TIP

HOLDER

CLUTCH

HOUSING

RETAINING

SPRINGS

BIT TIP

FIG. 4

LOCATOR

NUTSETTER

CLUTCH

HOUSING

ADJUSTING

COLLAR

NUTSETTER

GRB/386312-02 8/11/00 1:56 PM Page 2

T o lock the switch in the on position for continuous operation, depress the trigger switch and push up the locking button. The tool will continue to run. To turn the tool off, from a locked on condition, squeeze and release the trigger once. Before using the tool (each time), be sure that the locking button release mechanism is working freely. Be sure to release the locking mechanism before disconnecting the plug from the power supply. Failure to do so will cause the tool to start immediately the next time it is plugged in. Damage or injury could result.The reversing lever is used to reverse the tool for backing out screws. It is located above the trigger, shown in Figure 1. To reverse the screwdriver, turn it off and push the reversing lever to the right (when viewed from the back of the tool). To position the lever for forward operation, turn the tool off and push the lever to the left.

Dead Spindle Action

All GRABBER screwdrivers provide a dead output spindle to permit fasteners to be located easily in the driving accessory. Clutches are held apart by light spring pressure permitting the driving clutch to rotate without turning the driven clutch and accessory. When sufficient forward pressure is applied to the unit, the clutches engage and rotate the spindle and accessories. A reversing switch makes it possible to drive or loosen either right or left hand screws.

Accessory Assembly

The 1/4" hex drive ball lock chuck is used on all depth sensitive and drywall screwdrivers. Assemble accessories by engaging the hex spindle and tapping lightly on the accessory until it snaps in place. Usually pliers are required to remove the accessory by pulling forward.

Depth Sensitive Units

TO CHANGE BIT HOLDERS:

1. Pull forward on adjustment collar and remove from clutch housing.

2. Pull bit holder straight out with pliers if it is difficult to remove.

English

3. Push new bit holder into spindle until ball lock snaps in groove in bit holder shank.

4. Replace adjustment collar by snapping over retaining ring.

NOTE: Align ribs on inside of depth locator with grooves in clutch housing before snapping into place.

CHANGING BIT TIP

1. Pull forward on adjustment collar and remove it from clutch housing (see Figure 3).

2. Use pliers to remove worn bit and install new bit tip.

DEPTH ADJUSTMENT:

Follow the graphic on the collar to increase or decrease the fastening depth. To seat the screw deeper in the workpiece, turn the adjustment collar to the right. To seat the screw higher in the workpiece, turn the adjustment collar to the left.

INSTALLING AND CHANGING NUTSETTERS AND LOCATORS

Depth Sensitive Units for Drill Point Screws

1. To change or install a new nutsetter: a) Pull forward on adjustment collar and remove from clutch

housing. b) Pull nutsetters straight out with pliers c) Select nutsetter size desired. d) Two locators are supplied, a 9/16" ID for 3/8" nutsetters and

1/2" ID for 5/16" nutsetters. Match locator to desired size

nutsetter or bit holder.

2. Place nutsetter into clutch housing and push end of nutsetter until ball lock snaps into groove of nutsetter shank.

3. Reassemble adjustment collar by snapping over springs (see Figure 4).

NOTE: Align ribs on inside of depth locator with grooves in clutch housing.

GRB/386312-02 8/11/00 1:56 PM Page 3

+ 15 hidden pages