Black & Decker 2187, 2233, 2097, 2227 User Manual
L
EVEL COMMAND
WITH
9210 C
OMPRESSOR
30
200
60 90
400
600
800
2097 / 2187 / 2227 / 2233
120
L
EVEL
I
NSTALLATION INSTRUCTIONS
Congratulations on your purchase of a new Level Command
kit. This kit was designed to provide inflation control of your
air helper springs. This kit will be an asset to your vehicle,
meeting nearly all of your air supply needs.
Please take a few minutes to read through the instructions,
identify the components, and learn how to properly install your
Level Command kit.
N
OTE
:
The Level Command kit can be used with all air helper
spring products. If you are installing an air suspension system,
do not install the air line tubing to the air springs as stated in
the suspension system instruction manual. If you are adding
the Level Command kit to an existing air suspension system,
you will need to deflate the air springs and remove the air line
tubing.
psi
kPa
0 150
C
N
1000
PSI
OMMAND
OTE ON CONNECTING THE AIR LINE TUBING
Cut the air line tubing as squarely as possible. To connect
the air line tubing to the fittings, push the tubing into the fittings
as far as possible. If for any reason the tubing must be removed,
first release the air pressure from the air helper spring. Push the
collar toward the body of the fitting and the pull out the tubing.
To reassemble, make sure the tubing is cut squarely and push
the tubing back into the fitting.
T
OOLS REQUIRED
• 3/16"
• 1/4"
DRILL BIT
• W
IRE CRIMPER/STRIPPER
• P
HILLIPS SCREW DRIVER
• (2) 7/16"
:
DRILL BIT
WRENCHES
• 3/8"
• P
OWER DRILL
• P
LIERS
• U
TILITY KNIFE
• C
ENTER PUNCH
DRILL BIT
:
P
ARTS LIST
SINGLE AIR CONTROL PANEL 1
COMPRESSOR 9210 1
30 FT. AIR LINE TUBING 1
1/8" NPT PUSH-TO-CONNECT
STRAIGHT FITTING 3055 1
PUSH-TO-CONNECT
T-FITTING 3025 2
10 -32 x 1" MACHINE SCREW 5
10 -32 LOCK NUT 5
#10 FLAT WASHER 7
15 FT. 16 GAGE WIRE 1
IN-LINE FUSE HOLDER 1
20 AMP BLADE FUSE 1
FEMALE SPADE CONNECTOR 2
MALE SPADE CONNECTOR 1
RING TERMINAL 1
WIRE CONNECTOR 2
NYLON TIE 15
24-8204 03-01 NAD-30665-2
STRAIGHT AIR FITTING
2227
BLACK (TO GROUND)
12 VOLT, 20 AMP
MINIMUM IGNITION
ACTIVATED CIRCUIT
AIR LINE
Air Line & Wiring Diagram
RED
FUSE
WHITE
WHITE
POSITIVE, 12 VOLT
DASHBOARD
ILLUMINATION
CIRCUIT
60 90
400
30
200
psi
kPa
PSI
0 150
AIR LINE
600
1000
GROUND
120
800
1” MACHINE
SCREW
BRASS
INSERTS
RUBBER
ISOLATORS
Compressor Attachment
AIR COMPRESSOR
VEHICLE PANEL
1/4 HOLES TO
BE DRILLED
#10 FLAT WASHER
10/32 LOCK NUT
AIR SPRING
(sold separately)
Connectors:
Male spade connector
Ring T erminal
“T” FITTING
Femal spade connector
Wire connector
AIR SPRING
(sold separately)
Inline fuse connector
Figure “A”
Loading...